TechLogix Networx TL-TP100-HDC Users Manual

Page 1
User Manual
TL-TP100-HDC
100m HDBaseT Extender Set for HDMI, RS232, Ethernet & IR
Vers ion: TL-TP100-HDC _160926
Page 2
TL-TP100-HDC User Manual
www.tlnetworx.com
Preface
Read this user manual carefully before using this product. Pictures shown in this manual are for reference only; the actual product may vary.
This manual is only for operation instruction only and not for any maintenance or repair.
Trademarks
Product model and logo are trademarked. Any other trademarks mentioned in this manual are acknowledged as the properties of the trademark owner. No part of this publication may be copied or reproduced without prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the equipment.
Page 3
TL-TP100-HDC User Manual
www.tlnetworx.com
SAFETY PRECAUTIONS
To i ns u r e p ro p e r o p e r a t io n , please read all instructions carefully before using the device. Save this manual for further reference.
l Unpack the equipment carefully and save the original box and packing material for
possible future shipment
l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
l Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
l Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
l Refer all servicing to qualified service personnel.
l To p re v e n t f i r e o r s h o ck h a z a rd , d o n ot e x p o se t h e u ni t t o ra i n , m o is t u r e o r i n s ta l l t h is
product near water.
l Do not remove the housing of the device, as opening or removing housing may
expose you to dangerous voltage or other hazards.
l Install the device in a place with adequate ventilation to avoid damage caused by
overheating.
l Keep the device away from liquids.
l Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the device immediately.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
l Unplug the power cord when left unused for a long period of time.
l If disposing of the unit, do not burn or mix with general household waste. The device
must be disposed of per local regulations for electronic recycling.
Page 4
www.tlnetworx.com
TL-TP100-HDC User Manual
Table of Contents
1. Introduction ..................................................................................................................................... 1
1.1 Introduction to TL-TP70-HDC .......................................................................................... 1
1.2 Features ................................................................................................................................. 1
1.3 Package Contents ................................................................................................................ 1
2. Panel Description ........................................................................................................................... 2
2.1 Tra n s mi t t er ............................................................................................................................ 2
2.2 Receiver ................................................................................................................................. 3
3. System Connection ........................................................................................................................ 3
3.1 Usage Precautions ............................................................................................................... 4
3.2 System Diagram ................................................................................................................... 4
3.3 Connection Procedure ....................................................................................................... 5
3.4 Twi st ed P ai r Ca bl e Conn ec ti on ........................................................................................ 6
4. Specification .................................................................................................................................... 7
4.1 Supported Resolution ......................................................................................................... 7
5. Panel Drawing ............................................................................. Error! Bookmark not defined.
6. Tro u b le s ho o t in g & M ai n te n a nc e ................................................................................................. 9
7. After-sales Service ....................................................................................................................... 10
Page 5
1
www.tlnetworx.com
TL-TP100-HDC User Manual
1. Introduction
1.1 Introduction to TL-TP100-HDC
The TL-TP100-HDC is an ultra-thin extender set consisting of a transmitter (TL-TP100­HDC-T) and a receiver (TL-TP100-HDC-R). Using HDBaseT technology, the set transmits an HDMI signal to the receiver up to 100m distance via a twisted pair cable. Featuring bi-directional IR, Ethernet and RS232, you can control your display or source using the included accessories. With bi-directional PoE power, you only need to connect the power supply on one end.
1.2 Features
EDID pass through
HDCP 2.2 compliant
4K over Cat 5e/6 up to 40m
1080p over Cat 5e/6 up to 70m
Bi-directional IR, RS232
Ethernet pass-through
Note: Shielded twisted pair cable with shielded connectors are recommended.
1.3 Package Contents
Ø 1 x Tr an s m it t er (TX)
Ø 1 x Receiver (RX)
Ø 4 x Mounting ears
Ø 8 x Screws
Ø 8 x Plastic cushions
Ø 1 x Power adapter (DC 24V 1.25A)
Ø 2 x RS232 cables
Ø 1 x User manual
Page 6
2
www.tlnetworx.com
TL-TP100-HDC User Manual
2. Panel Description
2.1 Tr an s mi t te r
No.
Name
Description
LINK
HDBT link status indicator
Ø OFF: no link Ø GREEN: link successful Ø Blinking GREEN: link abnormal
HDCP
HDCP compliant indicator
Ø OFF: no HDMI traffic (no picture) Ø GREEN: traffic with HDCP Ø Blinking GREEN: traffic without HDCP
Power
OFF: No power RED: DC power present
RS232
RS232 control connector
IR IN
Connects to a 5V IR receiver (with carrier); signals tranmitted to the remote receiver
IR OUT
Connects to a 5V IR emitter (with carrier); signals tranmitted from the remote receiver
HDMI IN
Connect to an HDMI source
HDBT OUT
Connect to the HDBT IN socket on the receiver via a twisted pair cable; supports bi-directional PoH
RXTX
HDCPLINK
TX
Page 7
3
www.tlnetworx.com
TL-TP100-HDC User Manual
ETHERNET
100m Ethernet interface. Supports a four port LAN configuration whereas one of these 4 ports (both the Ethernet ports of transmitter and receiver) may be used for internet access and the others may be connected with computers. If a strong connection is present, the yellow LED indicators on the corresponding ports will blink and the green LED indicators will remain solid.
ETHERNET
DC 24V
Connect with DC24V 1.25A power adaptor. (Not necessary if receiver connects with power).
&
Pictures shown in this manual are only for reference.
2.2 Receiver
No.
Name
Description
LINK
HDBT link status indicator
Ø OFF: no link Ø GREEN: link successful Ø Blinking GREEN: link abnormal
HDCP
HDCP compliant indicator
Ø OFF: no HDMI traffic (no picture) Ø GREEN: traffic with HDCP Ø Blinking GREEN: traffic without HDCP
Tx Rx
HDCPLINK
RX
Page 8
4
www.tlnetworx.com
TL-TP100-HDC User Manual
Power
OFF: No power RED: DC power present
RS232
RS232 control connector
IR IN
Connects to a 5V IR receiver (with carrier); signals tranmitted to the remote transmitter
IR OUT
Connects to a 5V IR emitter (with carrier); signals tranmitted from the remote transmitter
HDMI OUT
Connect to an HDMI source
HDBT IN
Connect to the HDBT OUT socket on the transmitter via a twisted pair cable; supports bi-directional PoH
ETHERNET
100m Ethernet interface. Supports a four port LAN configuration whereas one of these 4 ports (both the Ethernet ports of transmitter and receiver) may be used for internet access and the others may be connected with computers. If a strong connection is present, the yellow LED indicators on the corresponding ports will blink and the green LED indicators will remain solid.
ETHERNET
DC 24V
Connect with DC24V 1.25A power adaptor. (Not necessary if transmitter connects with power).
&
Pictures shown in this manual are only for reference.
3. System Connection
3.1 Usage Precautions
1) System should be installed in a clean environment that has a proper temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be installed
properly.
3) All devices should be connected before powering on the devices.
4) The twisted pair terminations for the devices should be a straight-thru conforming
to the TIA/EIA T568B standard.
Page 9
5
www.tlnetworx.com
TL-TP100-HDC User Manual
3.2 System Diagram
3.3 Connection Procedure
Step1. Connect an HDMI source (such as a set top box) to the HDMI IN port of the
transmitter with an HDMI cable.
Step2. Connect HDBT OUT port of the transmitter to HDBT IN port of the receiver
using a twisted pair cable.
Step3. Connect an HDMI display to HDMI OUT port of the receiver with an HDMI
cable.
Step4. If IR control is required, perform the following:
a) Connect the IR emitter to the IR OUT port on either the transmitter or
receiver.
b) Connect the IR receiver to the IR IN port on either the transmitter or
receiver.
Step5. If RS232 control is required, connect the RS232 port of the devices to be
controlled to the receiver or the transmitter.
Step6. If Ethernet (LAN) support is required, connect one part to an internet servicing
device (such as a modem). The other ports may be connected to the devices.
Step7. Connect the DC24V power adaptor to either the transmitter or receiver. Power
will be transmitter to the remote extender via the twisted pair cable.
Receiver
Tx Rx
Tran smi tter
Tx Rx
CAT5 e/ 6A Cabl e
HDTV
S
t
a
n
d
b
y
Laptop
INTERNET
Wir eless R outer
Blu -ray DV D
HDM I Cable
HDM I Cable
Page 10
6
www.tlnetworx.com
TL-TP100-HDC User Manual
3.4 Twis te d Pa ir C ab le C on ne ct io n
The Cat5e/Cat6 terminations for HDBaseT devices should be a straight thru connection conforming to the TIA/EIAT568B standard. The TIA/EIA T568A standard is NOT recommended.
Note: For best operation, the twisted pair cable should be shielded and the cable connectors should be metallic. The shielded layer of cable MUST be connected to the connector’s metal shell.
TIA/EIA T568A
TIA/EIA T568B
Pin
Cable color
Pin
Cable color
1
green white
1
orange white
2
green
2
orange
3
orange white
3
green white
4
blue 4 blue
5
blue white
5
blue white
6
orange
6
green
7
brown white
7
brown white
8
brown
8
brown
1st
Ground
4--5
1st
Ground
4--5
2nd
Ground
3--6
2nd
Ground
1--2
3rd
Group
1--2
3rd
Group
3--6
4th
Group
7--8
4th
Group
7--8
Page 11
7
www.tlnetworx.com
TL-TP100-HDC User Manual
4. Specification
Model Spec
Tr an s mi t te r
Receiver Input
Input Signal
1 HDMI,1 IR in, 1 RS232
1 IR in, 1 HDBaseT, 1 RS232
Input Connector
1 HDMI female 1 3.5mm mini jack for IR in 1 3P captive connector
1 3.5mm mini jack for IR in 1 RJ-45 1 3P captive connector
Video Signal
HDMI1.4
HDMI1.4
Audio
Digital audio, transmit through HDMI audio
Digital audio, transmit through HDMI audio
Output
Output
1 HDBaseT, 1 IR out, 1 RS232
1 HDMI, 1 IR out, 1 RS232
Output Connector
1 RJ-45 1 3.5mm mini jack for IR out 1 3P captive connector
1 HDMI female 1 3.5mm mini jack for IR out 1 3P captive connector
Ethernet Port
Connector
2 Black RJ45, with a dual color indicators (Green & Yellow)
2 Black RJ45, with a dual color indicators (Green & Yellow)
Ethernet Tr an s m is s io n Speed
Adaptive 10M/100M (max), full duplex or half duplex.
General
Tr an s m is s io n Mo d e
HDBaseT
Resolution
800x600@60Hz1024x768@Hz1280x720@60Hz 1280x1024@60Hz 1366x768@60Hz 1600x1200@60Hz 1920x1080@60Hz 1920x1200@60Hz3D4K×2K
Tr an s m is s io n Di s ta n c e
1080P ≤ 100m; 4K×2K ≤ 70m
Bandwidth
10.2Gbps
HDMI Standard
HDMI1.4 & HDCP2.2
Impedance
75Ω
Temperature
0~ 50
Page 12
8
www.tlnetworx.com
TL-TP100-HDC User Manual
Humidity
0% ~ 90%
Power Consumption
10W
Power Supply
Input: 100VAC~240VAC, 50/60Hz; Output: 24VDC
1.25A
Dimension (W*H*D)
152mmx16.2mmx104mm
152mmx16.2mmx104mm
Net Weight
235g
241g
NOTE: All nominal levels are at ±10%.
5. Supported Resolutions
Aspect Ratio
Resolution
Refresh Rate
4Kx 2K 4096x2160
30Hz
3840x2160
24/25/30Hz
16:9
1920x1080
60Hz
1600x900
60Hz
1366x768
60Hz
1280x720
60Hz
1024x576
60Hz
16:10
1920x1200
60Hz
1680x1050
60Hz
1360x768
60Hz
1280x800
60Hz
4:3
1600x1200
60/65/70/75/85Hz
1280x1024
60/75/85/96Hz
1024x768
60/70/75/85Hz
800x600
56/60/72/75/85Hz
640x480
60/72/75Hz
Page 13
9
www.tlnetworx.com
TL-TP100-HDC User Manual
6. Panel Drawing
Page 14
10
www.tlnetworx.com
TL-TP100-HDC User Manual
7. Troubleshooting & Maintenance
l No image on display:
l Ensure that the display device has been set to the correct input.
l Ensure that the HDMI cables used for both the source/transmitter and the
receiver/display are properly connected and are working. Test the HDMI cables directly from a source to display and ensure their operation.
l Ensure that the twisted pair cable has not been damaged and that it has been
terminated correctly with T568B on both ends. A temporary length of twisted pair cable can be used for testing to ensure that the devices are all compatible and working properly.
l Ensure proper grounding of the power supply.
l Known issues with HDMI 1.2 source devices:
Older compatibility (HDMI 1.2) may result in HDBaseT transmission issues. Please contact Technical Support for a solution to these issues.
l Color lose or poor picture quality:
l Ensure that the HDMI cables used for both the source and transmitter and the
receiver and display are properly connected and are of good quality. Test the HDMI cables directly from a source to display and ensure their picture quality.
l Ensure proper grounding of the power supply.
l If the static becomes stronger or picture quality becomes worse when
connecting the video connectors, this may be due to improper grounding.
l Check the grounding and make sure all the components are properly grounded to
a common ground. Improper grounding may cause damage to the receiver.
l Lack of internet support or recognition via the Ethernet ports:
l Change the IP address of the extender of the devices connected to the
extenders.
If your problem persists after following the above troubleshooting steps, please contact your authorized reseller or TechLogix technical support.
Page 15
11
www.tlnetworx.com
TL-TP100-HDC User Manual
8. After-sales Service
1) Product Limited Warranty: We w arrant that our products will be f ree from defects in materials and workmanship for three years.
2) Warranty coverage may be voided wh en:
l The warranty period has expired l The factory applied serial number has been altered or removed from the product l There is damage, deterioration or malfunction caused by:
l Atypical wear and tear l Use of supplies or parts not meeting the specifications l No certificate or invoice as the proof of warranty l Damage caused by force majeure l Non-authorized service
3) Te c h n i c al S u p p o r t : When contacting TechLogix support, please have the following
information available:
l Product part number l Installation and sale date l Detailed failure information
Loading...