TechLogix Networx TL-FO2-HDC2 Users Manual

User Manual
TL-FO2-HDC2
300m Uncompressed 4K/60 HDMI & Control Fiber Optic
Extender Set
All Rights Reserved
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Preface
Read this user manual carefully before using this product. Pictures shown in this manual are for reference only; the actual product may vary.
This manual is only for operation instruction only and not for any maintenance or repair.
Trademarks
Product model and logo are trademarked. Any other trademarks mentioned in this manual are acknowledged as the properties of the trademark owner. No part of this publication may be copied or reproduced without prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the equipment.
SAFETY PRECAUTIONS
To insure proper operation, please read all instructions carefully before using the device. Save this manual for further reference. l Unpack the equipment carefully and save the original box and packing material for possible future
shipment
l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. l Do not dismantle the housing or modify the module. It may result in electrical shock or burn. l Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or
malfunction.
l Refer all servicing to qualified service personnel. l To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near
water.
l Do not remove the housing of the device, as opening or removing housing may expose you to
dangerous voltage or other hazards.
l Install the device in a place with adequate ventilation to avoid damage caused by overheating. l Keep the device away from liquids. l Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or
liquid falls or spills on to the housing, unplug the device immediately.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
l Unplug the power cord when left unused for a long period of time. l If disposing of the unit, do not burn or mix with general household waste. The device must be
disposed of per local regulations for electronic recycling.
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Table of Contents
Introduction ........................................................................................................................................ 4
Features at a Glance ..................................................................................................................... 4
Package Contents.......................................................................................................................... 4
Panel Descriptions............................................................................................................................. 5
Transmitter ..................................................................................................................................... 5
Receiver ........................................................................................................................................... 6
System Connection ........................................................................................................................... 7
Usage Precautions ......................................................................................................................... 7
Connection Procedure ................................................................................................................. 7
Panel Drawings .................................................................................................................................. 8
Transmitter ..................................................................................................................................... 8
Receiver ........................................................................................................................................... 9
Specifications ................................................................................................................................... 10
Troubleshooting and Maintenance .............................................................................................. 11
No image on display.................................................................................................................... 11
Color loss or poor picture quality:............................................................................................ 11
After-sales Service .......................................................................................................................... 12
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Introduction
The TL-FO2-HDC2 is an HDMI 2.0 (18G signal) with HDCP 2.2 support fiber optic extender that can reach up to 300 meters (984 ft) over a duplex OM3 cable with common LC terminations. The unit supports HDMI video resolutions up to 4K@60, HDR video, IR or RS232 pass-through controls, multichannel audio, as well as ARC with optional optical audio embedding and/or de-embedding. The TL-FO2-HDC2 is also compatible with HDMI 1.3/1.4 content with HDCP 1.3/1.4 content protection.
The TL-FO2-HDC2 supports two ARC connection modes: HDMI and S/PDIF, which results in four options to pass audio from the display to the head end. When the receiver is set to HDMI, audio from the display will pass to the transmitter via the HDMI output port. When the receiver is set to S/PDIF, audio from the display will pass to the transmitter via the S/PDIF optical audio port. When the transmitter is set to HDMI, audio from the receiver will be provided on the HDMI input port. When the transmitter is set to S/PDIF, audio from the receiver will be provided on the S/PDIF optical audio port.
Features at a Glance
Transmit HDMI, IR and RS232 over dual LC fiber optic cable
Full, uncompressed 18 Gbps HDMI video
Compatible with single mode (SM) and multimode (MM) fiber
HDMI 2.0 / HDCP 2.2
Supports HDR, ARC, EDID, CEC, deep color, and all digital audio formats
Includes IR accessories & mounting hardware
Package Contents
[1] Transmitter
[1] Receiver
[2] Mounting kits
[2] Power supplies (international)
[1] IR emitter
[1] IR receiver
[2] 3-Pin terminal blocks
[8] Rubber feet
[1] Fiber test cable
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Name
Description
1
Power LED
OFF: No power
RED: DC power present
2
Link LED
Optical link status indicator
OFF: no link
GREEN: link successful
Blinking GREEN: link abnormal
3
Status LED
HDCP compliant indicator
OFF: no HDMI traffic (no picture)
GREEN: traffic with HDCP
Blinking GREEN: traffic without HDCP
4
ARC Connection Switch
Select ARC output as HDMI or analog/optical
5
Firmware Port
Used for future firmware updates
6
Optical Out Port
Dual LC connectors to connect to the Optical Out port on the transmitter.
7
HDMI Input
Connect to an HDMI display
8
Audio Output
Optical audio (up to 5.1)
9
IR In
Connects to a 5V IR receiver (with carrier); signals tranmitted to the remote receiver. NOTE: Use TL-IR-CC if connecting to a third party control system.
10
IR Out
Connects to a 5V IR emitter (with carrier); signals are transmitted from the remote receiver
11
RS232
RS232 control connector
12
24V DC Input
Connect with DC12V power adaptor.
Panel Descriptions
Transmitter
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Name
Description
A
Power LED
OFF: No power RED: DC power present
B
Link LED
Optical link status indicator
OFF: no link
GREEN: link successful
Blinking GREEN: link abnormal
C
Status LED
HDCP compliant indicator
OFF: no HDMI traffic (no picture)
GREEN: traffic with HDCP
Blinking GREEN: traffic without HDCP
D
ARC Connection Switch
Select ARC input as HDMI or analog/optical
E
Firmware Port
Used for future firmware updates
F
Optical In Port
Dual LC connectors to connect to the Optical Out port on the transmitter.
G
HDMI Output
Connect to an HDMI display
H
Audio Input
Optical audio (up to 5.1)
I
IR In
Connects to a 5V IR receiver (with carrier); signals tranmitted to the remote receiver. NOTE: Use TL-IR-CC if connecting to a third party control system.
J
IR Out
Connects to a 5V IR emitter (with carrier); signals are transmitted from the remote receiver
K
RS232
RS232 control connector
L
24V DC Input
Connect with DC12V power adaptor.
Receiver
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
System Connection
Usage Precautions
System should be installed in a clean environment that has a proper temperature and humidity.
All of the power switches, plugs, sockets and power cords should be installed properly.
All devices should be connected before powering on the devices.
Port 1 of the transmitter connects to Port 2 of the receiver. Port 2 of the transmitter connects to port 1 of the receiver.
Connection Procedure
1. Connect an HDMI source (such as a set top box) to the HDMI IN port of the transmitter with an HDMI cable.
2. Connect OPTICAL OUT port of the transmitter to OPTICAL IN port of the receiver using a duplex fiber optic cable with LC connectors.
3. Connect an HDMI display to HDMI OUT port of the receiver with an HDMI cable.
4. If IR control is required, perform the following:
a. Connect the IR emitter to the IR OUT port on either the transmitter or
receiver.
b. Connect the IR receiver to the IR IN port on either the transmitter or
receiver.
5. If RS232 control is required, connect the RS232 port of the devices to be controlled to the receiver or the transmitter.
6. If Ethernet (LAN) support is required, connect the devices to the Ethernet ports.
7. If ARC (audio return channel) from the display to the source is required:
a. Receiver side:
i. HDMI audio: Slide the ARC Connection switch to HDMI.
ii. Optical audio: Slide the ARC Connection switch to ARC. Connect a
standard optical audio cable to the adapter.
b. Transmitter side:
i. HDMI audio: Slide the ARC Connection switch to HDMI.
ii. Optical audio: Slide the ARC Connection switch to ARC. Connect a
standard optical audio cable to the adapter.
8. Connect the DC12V power adaptors to the transmitter and receiver.
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Panel Drawings
Transmitter
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Receiver
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Transmitter Input/Output
HDMI Input
1 HDMI Receptacle
Optical Outp ut
2 LC Ports
ARC Outp ut
1 Optical Audio Port
IR Input/Output
2 3.5mm TRS Ports
RS232
1 3-pin Removable Terminal Block
12V DC
1 5.5mm OD/2.5mm ID Threaded Barrel Connector
ARC Audio Selector
1 2-position Switch
Receiver Input/Output
HDMI Output
1 HDMI Receptacle
Optical Input
2 LC Ports
ARC Input
1 Optical Audio Port
IR Input/Output
2 3.5mm TRS Ports
RS232
1 3-pin Removable Terminal Block
12V DC
1 5.5mm OD/2.5mm ID Threaded Barrel Connector
ARC Audio Selector
1 2-position Switch
Supported Audio, Video, and Control
Compatible Video Signals
All SD, HD, and other resol utions up to
- 4K/60 Hz / RGB and 4:4:4 8 bit (HDR)
- 4K/60 Hz / 4:2:2 10 bit (HDR)
- 4K/60 Hz / 4:2:0 10 bit (HDR)
Video Compliance
HDMI 2.0, HDMI 1.4, DVI 2.0 (Pixel clock up to 594 MHz)
Digital Content Protection
HDCP 1.2 / HDCP 2.2 Compatible
Embedded Audio
LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
ARC (Audio Return Channel)
Up to 6-channel audio
Supported RS232 Baud Rates
2400, 4800, 9600, 19200, 38400, 57600, 115200
Supported IR Carrier
33 to 55 kHz
Fiber Optic Transmission Characteristics
Required Cable Type
Duplex OM3 or OM4
Maximum Bandwidth
35 Gbps
Maximum Distance
300m (984 ft)
Signal Compression
None
Chassis and Environmental
Product Construction
Painted aluminum
Product Dimensions (W*H*D)
125 mm (4.92 in) x 19 mm (0.75 in) x 86 mm (3.17 in)
Product Operational Chassis Temperature
35 to + 44°C (95 to + 111 °F)
Environmental Operating Temperature
0 to + 45°C (32 to + 113 °F)
Environmental Operating Humidity
10% to 90%, non-condensing
Environmental Storage Temperature
-20 to +70°C (-4 to + 158 °F)
Environmental Storage Humidity
10% to 90%, non-condensing
Power and Regulatory
Power Input
12V DC
Power Supply Input
100-240V AC at 50/60 Hz; 0.5A Max
Power Supply Output
12V DC at 1 A
Maximum Power Consumption
6 watts
ESD Protection
Human-body Model: ±8kV Air-gap discharge and ±4kV Contact discharge
Regulatory Compliance
FCC, CE, RoHS, WEEE
Other
Warranty
Three years
Diagnostic LEDs
Link, Status, and Power
Included Accessories
IR Receiver (2 ea), IR Transmitter (2 ea), Mounting Ears (4 ea), Rubber Feet (8 ea), 12V 1A DC Power Supply (2 ea), 3-pin 3.5mm Terminal Block (2 ea), DE-9 to 3-pin RS232 Cable (2 ea)
Specifications
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
Troubleshooting and Maintenance
No image on display
Ensure that the display device has been set to the correct input.
Ensure that the HDMI cables used for both the source/transmitter and the
receiver/display are properly connected and are working. Test the HDMI cables directly from a source to display and ensure their operation.
Ensure that the fiber optic cable has not been damaged and that it has been terminated correctly with LC connectors on both ends. A temporary length of fiber optic cable can be used for testing to ensure that the devices are all compatible and working properly.
Ensure proper grounding of the power supply.
Color loss or poor picture quality:
Ensure that the HDMI cables used for both the source and transmitter and the receiver and display are properly connected and are of good quality. Test the HDMI cables directly from a source to display and ensure their picture quality.
Ensure proper grounding of the power supply.
If the static becomes stronger or picture quality becomes worse when connecting
the video connectors, this may be due to improper grounding.
Check the grounding and make sure all the components are properly grounded to a common ground. Improper grounding may cause damage to the receiver.
www.tlnetworx.com | +1-608-960-7242
TL-FO2-HDC2 User Manual
After-sales Service
Product Limited Warranty: We warrant that our products will be free from defects in materials and workmanship for three years.
Warranty coverage may be voided when: The warranty period has expired The factory applied serial number has been altered or removed from the product There is damage, deterioration or malfunction caused by: Atypical wear and tear Use of supplies or parts not meeting the specifications No certificate or invoice as the proof of warranty Damage caused by force majeure Non-authorized service
Technical Support: When contacting TechLogix support, please have the following information available: Product part number Installation and sale date Detailed failure information
www.tlnetworx.com | +1-608-960-7242
Loading...