3
4
5
5
6-7
7
8-10
9-11
12-13
13-14
15-16
17
Product Specifications
MyVoice 307 Overview
Getting Started
Charging Your Headset
Indicator Light
Pairing Your Headset with a Bluetooth Mobile Phone
Using Your Headset
Factory Reset
Troubleshooting
Safety Information
Care and Maintenance
Declaration of Conformity
Contents
2
User Guide
Bluetooth Headset
MyVoice 307
Product Specifications
Bluetooth Specification: v2.0 + EDR Class 2
Bluetooth Profiles Supported: Headset and Handsfree
Range of Frequency: 2.4GHz spectrum
Nominal Charging Time: Within 3 hours
Talk Time*: Up to 5 hours
Standby Time*: Up to 140 hours
Dimensions: 41 (L) x 20.5 (W) x 11.3 (H) mm /
1.61(L) x 0.81(W) x 0.44(T) inch
Weight: 8.9 grams / 0.32 ounces
* may vary due to the user’s habit, different modes of operation, and mobile phone
settings.
3 4
1. Multi-function Button (MFB)
• Power On / Off
• Pair with mobile phone
• Answer / End a call
• Last number redials
• Voice dialing
2. Volume
• Adjust volume
• Reject / Transfer a call
3. Status Indicator
4. Built-in Rechargeable Battery
5. Microphone
6. Charging Socket
7. Earpiece
MyVoice 307 Overview
(fig.1)
1
5
4
3
6
7
2
Getting Started
Charging Your Headset
To use your MyVoice 307 Bluetooth headset (“headset”), please follow the steps below:
1. Ensure your headset is fully charged.
2. Pair your charged headset with a Bluetooth-enabled mobile phone.
The headset comes with a built-in rechargeable
battery. Prior to using the headset for the first
time, it is recommended to fully charge the
battery.
Insert the charger’s plug into the headset’s USB
charging socket and plug the mains charger to
an AC wall outlet or plug to the PC/notebook.
5
Use only the supplied charger / USB charging cable to charge the headset.
Charge Plug
Charging Socket
Indicator Light
Headset Status Status Indicator
• Charging
• Fully charged
• Low battery
• Out of battery
• Out of Range
• Long blue
• The light turns off
• Double flash blue
• The light turns off
• Flash 4 blue every 15 sec until headset
reconnect and timeout after 10 mins
6
Status Indicator
♦ Charging indication will be delayed for a few seconds if the headset has not been used for a long
time or the battery is drained.
♦ 3 hours are required to fully charge the headset.
Indicator Light (cont’d)
7 8
Talk and Standby Time
A fully charged battery can offer up to 5 hours of talk time and up to 140 hours of standby time. The
headset remains in standby mode after being turned on.
Pairing Your Headset with a Bluetooth Mobile Phone
1) Ensure the headset is off.
2) To activate the pairing mode, press and hold the headset’s MFB without releasing your finger until its
status indicator showed long blue.
3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “MyVoice 307 ” and enter
the passcode “0000”. When the pairing is completed, the headset’s status indicator will flash blue
light rapidly five times.
If the pairing cannot be completed within two minutes after the pairing mode has been activated, the
headset’s status indicator will stay blue five seconds and then turns to standby mode. Repeat steps 1 to
3 to pair the devices again.
Function Button Audio Status indictor
POWER ON Press and hold
the MFB
When you turn on your headset for the first time, the headset proceeds into pairing
mode, i.e. the status indicator blinks green, so that you can immediately pair it with
your mobile phone.
a Short beep Flash blue light 3 times
POWER OFF Press and hold the
MFB for 2 seconds
a Long beep Blue light for two
seconds and then the
light goes off
End a call Press the MFB once
Answer a call Press the MFB once
Incoming call Ringtone on earphone Quick flashing blue light
Flashing blue light
Flashing blue light
Using your headset
9 10
Say the voice tag as soon as you hear the short beep and you must have recorded the
voice tag into your mobile phone.
Function Button Audio Status indictor
Adjust Volume Press the Volume
Key once to increase
by 1 step (Total 6
levels)
a Short beep Flashing blue light
Voice Dialing* Press the MFB once a short beep
a short beep
Flashing blue light
Reject a call* Press and hold the
Volume Key for 2
seconds
Double click the MFBLast no. Redial*
Flashing blue light
Flashing blue light
Using your headset (cont’d)
Function Button Audio Status indictor
Call Transfer
(mobile phone
to headset)*
While speaking,
press MFB once
Flashing blue light
* Subject to mobile support
Call Transfer
(headset to
mobile phone)*
While speaking, press
and hold the volume
Key for 2 seconds
Flashing blue light
Using your headset (cont’d)
Factory Reset
You may reset the headset to its default settings. Resetting will also remove the pairing history of your
headset with the mobile phone.
1. Hold the volume key and plug charging cable into the charging socket until earpiece will beep 2
times.
2. Release the volume key.
3. The headset is reset.
i.Tech Bluetooth headset is designed to work with Bluetooth devices. Due to large variability between
different Bluetooth devices from different manufacturers, interoperability between the headset and all
Bluetooth-enabled products is not guaranteed.
11 12
Troubleshooting
I can hear crackling noise.
To receive the best audio quality, it is recommended to wear your headset on the same side of
the body as your mobile phone.
I can't hear anything in my headset.
• Ensure the headset is turned on and is properly charged.
• Ensure the headset is properly paired with the mobile phone.
• Make sure that the mobile phone is connected with the headset – if it does not connect,
either refer to the mobile phone's Bluetooth menu or by pressing the MFB once (see “Using
Your Headset” and “Pairing Your Headset with a Bluetooth Mobile Phone”).
I can't connect my headset with my mobile phone.
• Ensure your headset is turned off and is properly charged.
• Ensure the headset is properly paired with your mobile phone.
• Ensure your mobile phone’s Bluetooth feature is activated. Please refer to your mobile
phone user guide for specific instruction.
• Ensure the headset is within ten metres range of your mobile phone and there are no
obstructions, such as walls or other electronic devices in between.
If the above steps do not solve your problem, please recharge the headset and remove your
mobile phone’s battery for a while.
13 14
Troubleshooting (cont’d)
I can’t turn off the headset or the headset does not respond
• You may do a “hardware reset” on your headset if you can’t turn it off or it doesn’t respond.
• Plug charging cable into the charging socket, the headset is reset
Safety Information
• Check and observe local laws regarding the use of a mobile phone and a headset while
driving. If you use the headset while driving, ensure your full attention and focus. It is your
responsibility to drive safely. Consider to pull off the road before making or answering a call.
• Never leave your headset above any air bag deployment area inside your car as serious
injury may result when an air bag deploys.
• Never allow children to play with the headset – small parts may be of choking hazard.
• Observe all signs and displays that require an electrical device or RF radio product to be
switched off in designated areas. These could include hospitals, blasting areas, and
potentially explosive atmospheres.
• Turn off your headset prior to boarding an aircraft. Do not use your headset inside an
aircraft.
Safety Information (cont'd)
• To prevent damage to your hearing, please do not set the listening volume too high.
• Do not attempt to modify the headset.
• Do not keep the headset near a wash basin or other wet places.
• Do not use the headset outdoors in the rain.
• Do not use the headset in stormy weather.
• Do not clean the headset while it is being charged. Always disconnect the charger from the
headset before cleaning.
• Do not attempt to force open the built-in battery.
• Only charge the headset’s built-in battery in accordance with the instructions described in
this user guide.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
FCC RF Radiation Exposure Statement:
15
Headset
• Turn off your headset before placing it in your pocket or bag. If the MFB is accidentally
depressed, your mobile phone may place an unintended call.
• Do not expose the headset to liquid, moisture or humidity, or rain as it is not waterproof.
• Do not use abrasive cleaners to clean the headset.
Care and Maintenance
• Do not expose the headset to extremely high or low temperatures.
• Do not expose the headset in direct sunlight when it is fully charged
• Do not leave the headset near open flames such as cooking burners.
• Do not dispose of the headset in a fire, as it will result in explosion.
• Do not bring the headset into contact with any sharp objects, as this will cause scratches and
damages.
• Do not stick anything inside the headset, as this may damage internal components.
• Do not attempt to disassemble the headset as it does not contain serviceable components.
• If you do not plan to use the headset for a long period, please store it in a dry place that is
free from extreme temperatures and dust.
• Avoid charging the headset in extremely high or low temperatures.
• Dispose of the battery and the headset according to local regulations. Do not dispose of
them as household waste.
16
Built-in Battery
• Do not attempt to replace the headset’s battery as it is in-built and is not changeable.
• Dispose of the battery according to local regulations. Do not dispose of the battery as
household waste.
• Charge the battery in accordance with the instructions supplied with this user guide.
Charger
• Use only the charger supplied by the headset’s original manufacturer to charge the headset.
Other chargers may look similar but using them could be dangerous and could damage the
headset.
Care and Maintenance (cont’d)
• Do not attempt to disassemble the charger as it may expose you to dangerous voltages or
other risks. Incorrect reassembly can cause electric shock when the headset is subsequently
used.
• Do not use the charger outdoors or in damp areas.
17 18
Declaration of Conformity
We, i.Tech Dynamic Limited, declare that the following product:
Product Name: i.Tech MyVoice 307
Model No.: C51-B307-XX
is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred
to as R&TTE Directive): Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance
with Annex II of the above directive.
A copy of the Declaration of Conformity can be found at http://www.itechdynamic.com.
Notes on Environmental Protection
After the implementation of the European Directive 2002/96/EU in the national legal system, the
following applies: Electrical and electronic devices must not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at the end of their service
lives to the public collection points that are set up for this purpose or designated points of sale.
However, such details are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the packaging indicates that the product is subject to these
regulations. By recycling, reusing the materials, or other forms of utilizing old devices, you are
making an important contribution in protecting our environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
15.21
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Federal Communications Commission (FCC) Statement
19
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) Statement
Dispose of the packaging and this product in accordance
with the latest provisions.
2009 Hutchison Harbour Ring Enterprises Limited
All rights in this publication are reserved and no part may be reproduced without the prior written
permission of the publisher. The contents of this publication are believed to be correct at the time
of going to press, but any information, specifications, products or services mentioned, and product
I.D. shown may be modified, supplemented or withdrawn without further notice. The Stylized i.Tech
logos are trademarks owned by Hutchison Harbour Ring Enterprises Limited or its affiliates. All
other trademarks or registered trademarks belong to their respective owners.
06/2009
S3J-A307US-01-F
Loading...