TECCOR S2055W, S2035J, S2065J, S2070W, S4055W Datasheet

...

Selected Packages*

File #E71639

U.L. RECOGNIZED

TO-202

TO-92

*TO-218X

*TO-218

TO-263

Pak

TO-252

D-Pak

3-lead

Compak

*TO-220

General Description

The Teccor line of thyristor SCR semi-conductors are half-wave, unidirectional, gate-controlled rectifiers which complement Teccor's line of sensitive SCRs. Teccor offers devices with ratings of 1 A to 70 A and 200 V to 1000 V, with gate sensitivities from 10 mA to 50 mA. If gate currents in the 12 µA to 500 µA ranges are required, see “Sensitive SCRs” section of this catalog.

Three packages are offered in electrically isolated construction where the case or tab is internally isolated to allow the use of low-cost assembly and convenient packaging techniques.

The Teccor line of SCRs features glass-passivated junctions to ensure long-term reliability and parameter stability. Teccor’s glass offers a rugged, reliable barrier against junction contamination.

Variations of devices covered in this data sheet are available for custom design applications. Consult the factory for more information.

TO-251

V-Pak

(1 A to 70 A)

Features

• Electrically-isolated package

• High voltage capability — 200 V to 1000 V

• High surge capability — up to 950 A

• Glass-passivated chip

Compak SCR

• Surface mount package — 1 A series

• New small profile three-leaded Compak package

• Packaged in embossed carrier tape with 2,500 devices per reel

• Can replace SOT-223

SCRs Data Sheets

TYPE

10 A

12 A

Part Number

Isolated Non-isolated

TO-92

S201E S2N1 1 0.64 200 1 10

S401E S4N1 1 0.64 400 1 10

S601E S6N1 1 0.64 600 1 10

TO-220 TO-202

S2006L S2006F1 S2006V S2006D 6 3.8 200 1 15

S4006L S4006F1 S4006V S4006D 6 3.8 400 1 15

S6006L S6006F1 S6006V S6006D 6 3.8 600 1 15

S8006L S8006V S8006D 6 3.8 800 1 15

SK006L SK006V SK006D 6 3.8 1000 1 15

S2008L S2008F1 S2008R S2008V S2008D 8 5.1 200 1 15

S4008L S4008F1 S4008R S4008V S4008D 8 5.1 400 1 15

S6008L S6008F1 S6008R S6008V S6008D 8 5.1 600 1 15

S8008L S8008R S8008V S8008D 8 5.1 800 1 15

SK008L SK008R SK008V SK008D 8 5.1 1000 1 15

S2010L S2010F1 S2010R S2010V S2010D 10 6.4 200 1 15

S4010L S4010F1 S4010R S4010V S4010D 10 6.4 400 1 15

S6010L S6010F1 S6010R S6010V S6010D 10 6.4 600 1 15

S8010L S8010R S8010V S8010D 10 6.4 800 1 15

SK010L SK010R SK010V SK010D 10 6.4 1000 1 15

See “Package Dimensions” section for variations. (11)

TO-220

S2012R S2012V S2012D 12 7.6 200 1 20

S4012R S4012V S4012D 12 7.6 400 1 20

S6012R S6012V S6012D 12 7.6 600 1 20

S8012R S8012V S8012D 12 7.6 800 1 20

SK012R SK012V SK012D 12 7.6 1000 1 20

TO-251

V-Pak Compak

TO-252

D-Pak

(1) (2) (15)

Amps

T(RMS)IT(AV)

MAX MAX MIN MIN MAX

& V

DRM

Volts

RRM

(4)

mAmps

Specific Test Conditions

di/dt — Maximum rate-of-rise of on-state current; IGT = 150 mA with

£ 0.1 µs rise time

dv/dt — Critical rate of applied forward voltage

t — RMS surge (non-repetitive) on-state current for period of 8.3 ms

for fusing

and I

DRM

Igt — dc gate trigger current; VD = 12 V dc; RL = 60 W for 1 to 16 A

devices and 30 W for 20 to 70 A devices

— Peak gate current

— dc holding current; gate open

— Maximum on-state current

— Peak one-cycle forward surge current

TSM

G(AV)

— Peak gate power dissipation

— Gate controlled turn-on time; gate pulse = 100 mA; minimum

— Peak off-state forward and reverse current at V

RRM

— Average gate power dissipation

DRM

and

and V

DRM

— DC gate trigger voltage; VD = 12 V dc; RL = 60 W for 1 to 16 A

devices and 30 W for 20 to 70 A devices

— Peak on-state voltage at maximum rated RMS current

General Notes

• All measurements are made at 60 Hz with a resistive load at an ambient temperature of +25 °C unless otherwise specified.

• Operating temperature range (T devices and -40 °C to +125 °C for all other packages.

• Storage temperature range (T devices, -40 °C to +150 °C for TO-202 and TO-220 devices, and

-40 °C to +125 °C for all others.

• Lead solder temperature is a maximum of 230 °C for 10 seconds maximum; ³1/16" (1.59 mm) from case.

• The case temperature (T outline drawings in the “Package Dimensions” sectionof this catalog.

— Repetitive peak off-state forward and reverse voltage

RRM

) is -65 °C to +125 °C for TO-92

) is -65 °C to +150 °C for TO-92

) is measured as shown on dimensional

width = 15 µs with rise time £ 0.1 µs

— Circuit commutated turn-off time

Data Sheets SCRs

DRM

& I

(14)

RRM

(3)

(8)

(17)

(5) (13)

(12)

GMPG(AV)ITSM

(12)

(6) (10)

dv/dt I2t di/dt

(7)

(9) (10)

mAmps

TC =

25 °C

100 °C

0.01 0.2 0.5 1.6 1.5 30 1.5 15 0.3 30/25 40 20 3.7 50 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35

0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35

0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 350 250 41 100 2 35

0.01 0.2 0.5 1.6 1.5 30 2 20 0.5 100/83 300 225 41 100 2 35

0.02 0.5 1 1.6 1.5 30 2 20 0.5 100/83 250 200 41 100 2 35

0.02 3 1.6 1.5 30 2 20 0.5 100/83 100 41 100 2 35

0.01 0.5 1 1.6 1.5 40 2 20 0.5 120/100 350 250 60 100 2 35

0.01 0.5 1 1.6 1.5 40 2 20 0.5 120/100 300 225 60 100 2 35

0.02 0.5 1 1.6 1.5 40 2 20 0.5 120/100 250 200 60 100 2 35

0.02 3 1.6 1.5 40 2 20 0.5 120/100 100 60 100 2 35

TC =

125 °C

MAX MAX MAX MAX MIN MIN TYP MAX

Volts

TC =

25 °C

Vol ts

TC =

25 °C

mAmps

Amps

Watts Watts

Amps Volts/µSec

60/50 Hz

100 °C

TC =

125 °C

Amps

Sec Amps/µSec

µSec

Electrical Specification Notes

(1) See Figure E6.5 through Figure E6.16 for current rating at

specified operating case temperature.

(2) See Figure E6.1 and Figure E6.2 for free air current rating.

(3) See Figure E6.19 and Figure E6.20 for instantaneous on-state

current versus on-state voltage (typical).

(4) See Figure E6.18 for I

(5) See Figure E6.17 for I

(6) For more than one full cycle rating, see Figure E6.23.

(7) See Figure E6.22 for t

(8) See Figure E6.21 for V

(9) Test conditions are as follows:

= 1 A for 1 A devices and 2 A for all other devices

•I

versus TC.

versus IGT.

versus TC.

(11) See package outlines for lead form configuration. When ordering

special lead forming, add type number as suffix to part number.

(12) Pulse width £10 µs

(13) Initial on-state current = 200 mA dc for 1 A through 16 A devices;

400 mA dc for 20 A through 70 A devices.

= TJ for test conditions in off state.

(14) T

(15) The R, K, or M package rating is intended for high surge condition

use only and not recommended for ³50 A rms continuous current use since narrow pin lead temperature can exceed PCB solder melting temperature. Teccor's J package or W package is recommended for ³50 A rms continuous current requirements.

(16) For various durations of an exponentially decaying current

waveform, see Figure E6.3 and Figure E6.4. (t

is defined as

5 time constants.)

(17) Minimum non-trigger V

at 125 °C is 0.2 V.

• Pulse duration = 50 µs, dv/dt = 20 V/µs, di/dt = -10 A/µs for 1 A devices, and -30 A/µs for other devices

•I

= 200 mA at turn-on

(10) See Figure E6.5 through Figure E6.10 for maximum allowable

case temperatures at maximum rated current.

SCRs Data Sheets

Part Number

Isolated Non-isolated

TO-263

Pak

TYPE

TO-220 TO-218X TO-218 TO-220 TO-218X TO-218

See “Package Dimensions” section for variations. (11) MAX MIN MIN MAX MAX

S2015L 15 9.5 200 1 30 0.01 0.5 1

15 A

S4015L 15 9.5 400 1 30 0.01 0.5 1

S6015L 15 9.5 600 1 30 0.01 0.5 1

S8015L 15 9.5 800 1 30 0.02 1 2

SK015L 15 9.5 1000 1 30 0.02 3

S2016R S2016N 16 10 200 1 30 0.01 0.5 1

16 A

S4016R S4016N 16 10 400 1 30 0.01 0.5 1

S6016R S6016N 16 10 600 1 30 0.01 0.5 1

S8016R S8016N 16 10 800 1 30 0.02 1 2

SK016R SK016N 16 10 1000 1 30 0.02 3

S2020L 20 12.8 200 1 30 0.01 0.5 1

20 A

S4020L 20 12.8 400 1 30 0.01 0.5 1

S6020L 20 12.8 600 1 30 0.01 0.5 1

S8020L 20 12.8 800 1 30 0.02 1.0 2

SK020L 20 12.8 1000 1 30 0.02 3

S2025L S2025R S2025N 25 16 200 1 35 0.01 1 2

25 A

S4025L S4025R S4025N 25 16 400 1 35 0.01 1 2

S6025L S6025R S6025N 25 16 600 1 35 0.01 1 2

S8025L S8025R S8025N 25 16 800 1 35 0.02 1.5 3

SK025L SK025R SK025N 25 16 1000 1 35 0.02 3

S2035J S2035K 35 22 200 5 40 0.01 1 2

35 A

S4035J S4035K 35 22 400 5 40 0.01 1 2

S6035J S6035K 35 22 600 5 40 0.01 1 2

S8035J S8035K 35 22 800 5 40 0.02 1.5 3

SK035K 35 22 1000 5 40 0.02 3

S2040R S2040N 40 25 200 5 40 0.01 1 2

40 A

S4040R S4040N 40 25 400 5 40 0.01 1 2

S6040R S6040N 40 25 600 5 40 0.01 1 2

S8040R S8040N 40 25 800 5 40 0.02 1.5 3

SK040R SK040N 40 25 1000 5 40 0.03 5

S2055R S2055W S2055M S2055N 55 35 200 5 40 0.01 1 2

55 A

S4055R S4055W S4055M S4055N 55 35 400 5 40 0.01 1 2

S6055R S6055W S6055M S6055N 55 35 600 5 40 0.01 1 2

S8055R S8055W S8055M S8055N 55 35 800 5 40 0.02 1.5 3

SK055R SK055M SK055N 55 35 1000 5 40 0.03 5

S2065J S2065K 65 41 200 5 50 0.02 1.5 3

65 A

S4065J S4065K 65 41 400 5 50 0.02 1.5 3

S6065J S6065K 65 41 600 5 50 0.02 1.5 3

S8065J S8065K 65 41 800 5 50 0.02 2 5

SK065K 65 41 1000 5 50 0.03 5

S2070W 70 45 200 5 50 0.02 1.5 3

70 A

S4070W 70 45 400 5 50 0.02 1.5 3

S6070W 70 45 600 5 50 0.02 1.5 3

S8070W 70 45 800 5 50 0.02 2 5

See “General Notes” on page E6 - 2 and “Electrical Specification Notes” on page E6 - 3.

(1) (15)

Amps

T(RMS)IT(AV)

DRM

RRM

Volts

(4)

mAmps

TC =

25 °C

DRM

& I

(14)

mAmps

TC =

100 °C

RRM

TC =

125 °C

+ 8 hidden pages