TEAM Electronic PT3208S handbuch

TEAM PT3208S

electronic

PMR­&
optional
erweiterbares
Betriebsfunkgerät

Bedienungsanleitung
Manual
Mode d’emploi

11

ENGLISH

TEAM PT-3208S

Manual

Table of Contents

page

Displays and Controls 2
Setting Up the TEAM PT-3208S 12

Mounting of the Accumulator 12
Mounting and Removing of the Belt Clip 12

Operation of the TEAM PT-3208S 13

1) Turning the Unit On/Off 13

2) Volume Level Adjustment 13

3) Channel Selection 13

4) Transmission 13

5) Reception 13

6) Sockets for External Speaker-Microphone 14

7) Charging of the Accumulator 14

8) Low Power Indicator 14
Scan Function of the TEAM PT-3208S 14

1) Start of Scan Function 15

2) End of Scan Function 15

3) Restart of the Scan Function 15

4) Transmission during activated Scan Function 15
Auxiliary Functions of the TEAM PT-3208S 15

1) Transmit Time Limiter 15

2) Busy Channel Lockout Function 16

3) Energy Saving Function 16

4) Additional Muting Function 16
General 17

1) Safety 17

2) Service 17

3) Conformity 17

4) Programmed Channels 17

5) Programmed Functions 17 - 18

6) Technical Data 18

7) CTCSS-Tones and DQT-Codes 27

Setting up the TEAM PT-3208S

Unpack carefully your UHF radio PT-3208S. Please check whether the supplied material mat­ches with the positions listed below. In case of loss or damage of a part contact your carrier at
once.

This transceiver is a heavy duty PMR radio, which can be optionally modified by your dealer also
into a professional transceiver together with the PMR channels. In this unit only the channels
1 – 8 are already factory-preset to the PMR channels, i.e. the number of the rotary channel selector
position corresponds with the actual PMR channel. The positions 9 – 16 are free according to
the factory setting. The TX output power on the PMR channels is reduced to 500 mW in the
radiated field according to the European regulation. See in the chapter “technical data“ for the
table of the PMR channel numbers together with the corresponding frequencies. When the unit
remains in pure PMR operation, it is free of charge and registration in most European countries.
If you want to use the unit as a professional transceiver, you have to contact your local tele­communication authorities. You may be required to pay costs of registrations and annual fees for
every unit and for every frequency. If your application is passed, you can go to your dealer and
let him set your PT-3208S to the permitted frequency(ies) and adjustments.

Mounting of the Accumulator

At first turn the rear panel towards you. Place the accumulator ( 9 ) in that way
on the unit’s rear panel that the 4 slip planes of the unit grip into the correspond­ing guiding slots of the accumulator, and that the accumulator’s charging
contacts show into the direction of the unit’s base. Then push the accumulator
under simultaneous slight pressure on its back into the direction of the unit’s top
side, until the latch on the unit’s base clicks into place. Now the unit is ready for
radio operation.

Detaching of the Accumulator

Turn again the unit’s rear panel towards you. To release the accumulator from
the unit you have to pull the latch on the unit’s base with your finger towards the
unit’s front panel, while pushing simultaneously the accumulator towards the

unit’s base. After the accumulator is slid out of the unit’s slip planes you can take it off.
Removing and mounting of the belt clip

Turn the rear panel towards you.

Mounting of the Belt Clip

Pull the springy support of the belt clip a bit out of its rest position by using your
index finger and your middle finger. When the support is parallel to belt clip’s main
part insert it from above into the corresponding guide on the back of the accumu­lator. Push the belt clip into the direction of the unit’s base until the belt clip’s latch
clicks into place.

Detaching

The latch of the belt clip is located on the accumulator’s back near the top side.
Pull the latch with your fingernail away from the accumulator’s back and push
simultaneously the belt clip towards the unit’s top side. After the belt clip is slid out
of its guide you can take it off.

battery pack

belt clip desktop

charger

wrist loop

adapter

manual
Declaration of

Conformity

12

ENGLISH

Operation of the TEAM PT-3208S

1) Turning the unit On/Off
To turn on the unit rotate the volume control with ON/OFF switch [VOLUME/OFF] ( 4 )
from its rest position clockwise until you hear a clicking sound. A short beep tone will
be heard from the loudspeaker ( 8 ), which indicates that the unit is in reception mode.
To switch off the unit rotate the volume control with ON/OFF switch [VOLUME/OFF] ( 4 )

counterclockwise to the final stop [OFF] until you hear a clicking sound. This indicates that the
unit is switched off now.

2) Volume level adjustment

If a radio operator sends a message on the actual channel, you can hear it in the
incorporated loudspeaker ( 8 ). If the actual channel is free, the loudspeaker will be
silent. In this case you can produce a strong noise in the loudspeaker by pressing the

monitor key ( 6 ). Adjust the volume control [VOLUME/OFF] ( 4 ) to a comfortable
listening level. Turning the control clockwise will increase the volume level and turning it coun­terclockwise will reduce the volume level.

3) Channel selection

The TEAM PT-3208S has maximal 16 channels available. To select another channel

turn the rotary channel selector [1-15, S] ( 3 ). According to the programming of the

channels, which has been made by your dealer, the unit will call up those transmit and

reception frequencies which correspond to the actual position 1 – 15 ( 16 ) of the
rotary channel selector.

Note: If the rotary channel selector is set to a not programmed position, you will hear a con­tinuous warning tone in the loudspeaker.

4) Transmission
Do not transmit if the antenna ( 1 ) is not mounted. Check activity on the actual channel. Do not
send if someone talks on the actual channel. Only if the loudspeaker is silent and the control
lamp ( 2 ) is dark, the channel is free. Press also the monitor key ( 6 ). There must be a noise if
the channel is not occupied.
To transmit depress and hold the PTT key ( 5 ). During transmission the control lamp ( 2 ) lights
up red and the rotary channel selector is disabled. Hold the unit upright. The sensitivity of the
built-in microphone is set for speaking at a distance of 2 inches. Speaking too loud will cause
distortions and makes the signal difficult to understand. On completion of the transmission re­lease the PTT key and the set will return to receive mode.

Note: Radio operation is only possible with the counter operator at coinciding channels.

5) Receiving
After being switched on, the unit is always in receiving mode, as long as it is not transmitting.
When it does not find any signal on the actual channel, it would produce a disturbing noise in the
loudspeaker ( 8 ). For this end the unit is equipped with a built-in noise suppression circuit
( squelch ) that mutes the receiver if there is no station on the actual channel. If there is any
incoming signal, the squelch will turn the loudspeaker on and cause the control lamp ( 2 ) simul­taneously to light up green. This indicates that the channel is occupied. Your dealer can adjust
the squelch threshold. The squelch function can be disabled to hear also weak stations which
are not strong enough for the squelch to turn the loudspeaker on ( monitor function ).
Depress the monitor key ( 6 ). Now the noise suppression is shut off and the control lamp lights
simultaneously up green. If there is no station on the actual channel you hear a noise in the spea­ker. To reactivate the squelch release the monitor key ( 6 ) again. Thus the squelch works again.
The monitor key function can also be changed by your dealer. For further information see point
4 of the chapter “Auxiliary functions of the PT-3208S”.

ENGLISH

13

6) Sockets for External Speaker-Microphone
Behind the screw-fixed cover on top of the unit’s right side you can find two jack
sockets for stereo plugs Ø 2,5/3,5 mm [SPK/MIC] ( 7 ). They serve for the connec­tion of a speaker-microphone with PTT function or for a separate microphone or a
separate speaker. As already indicated on the cover, the upper socket is for the spea­ker and the lower socket is for the microphone. The internal speaker and/or the inter­nal microphone will be switched off, if the socket for the corresponding external
accessory is in use.

7) Charging of the Accumulator

The accumulator is not charged in the factory. Therefore it must be charged before
it is used the first time.
Insert the DC connector of the power cord coming from the adapter into the socket
on the rear of the charging mould. Then connect the adapter with a wall outlet
( 230 V, 50 Hz ).
Now insert the transceiver with mounted accumulator or only the accumulator it­self into the charging mould. The front panel must show into the direction of the
push button, or the charging contacts to the rear.

The red LED ( CHARGING ) on the charging mould lights up now, which indicates
that the charging process has started. After approximately six hours the red LED turns off and
the green LED ( COMPLETION ) lights up. That means that now the accumulator is charged and
the charging current is reduced. The charging process can be continued for 1 or 2 hours after
the green LED has turned on, to take advantage of the entire capacity of the accumulator. But
do not exceed the charging duration beyond this time, otherwise you will cause an overcharging
which will reduce the accumulator capacity or shorten the accumulator life. Atoo frequent recharging
of a partially discharged accumulator will also result in a reduction of its capacity. For this end
the charging mould is equipped with a discharge function. To activate a previous discharging of
a partially discharged accumulator insert the transceiver with mounted accumulator or only the
accumulator itself into the charging mould. After the red LED has begun to light up, depress brief­ly the button on the charging mould. This will cause the red LED to turn off and the yellow LED
( DISCHARGING ) to turn on. That means that the accumulator is discharged now. At the end of
the discharge process the yellow LED turns off automatically and the red LED
( CHARGING ) lights up again. This indicated that the charging process has started automati­cally. At the end of the charge process the red LED turns off and the green LED lights up again,
which indicates that the accumulator is charged now.
Never try to recharge alkaline cells or other accumulators than the supplied one with the charg­ing mould.

8) Accumulator Alert Indication
The unit is equipped with a accumulator level monitoring circuit which alerts you, when the stor­ed energy is nearly completely used up. If the accumulator voltage drops below a certain value
in receiving mode, you will hear a warning tone in the speaker. If the accumulator voltage drops
below this value while transmitting, the control lamp ( 2 ) starts to flash red. After releasing the
PTT key and pressing it once again now, the unit will not transmit any more. Now it is time to
recharge the accumulator.

Scan function of the TEAM PT-3208S

The scan function must be installed into your transceiver by your dealer, before you can use it.
If it is not installed, there is another channel available on position [S] ( = 16 ) of the rotary chan­nel selector. In the description below it is assumed that the scan function is active. Ask your dea­ler for more details.

14

ENGLISH

1) Start of the scan function
When you turn the rotary channel selector on position [S] ( = 16 ) the unit runs through all chan­nels which your dealer has selected for the scan function ( scanning list ). If there is a radio
operator signal on one channel which is strong enough to open the squelch, the scan function
will pause on that channel. You can hear the partner station but the scan remains active.

2) End of the scan function
When you turn the rotary channel selector on a position between 1 and 15 the scan function is
not active.

3) Restart of the scan function
Your dealer can select between two conditions under which the scan function restarts stepping
through the scanning list when it has previously stopped on an occupied channel:
a) Time control: The scan function restarts working after a dealer-set dwell time between 0.5 and
5 s, beginning from the moment of stopping on that channel. The dwell time does not depend on
whether the channel is free or still occupied.
b) Carrier wave control: The scan function restarts working 3 s after the radio operator signal has
dropped below the squelch threshold.

4) Transmission during activated scan function
Your dealer can select one of 4 different criteria to determine the transmit frequency while the
scan function is active:
a) First channel: When pressing the PTT key while the scan function is active the unit transmits
basically on the first channel on the scanning list, i.e. the channel with the lowest channel num­ber.
b) First channel or actual channel: When the pressing of the PTT key occurs while the scan fun­ction is stepping through the scanning list, the unit transmits on the first channel on the scanning
list. When the pressing of the PTT key occurs while the scan function is resting on a channel, the
unit transmits on this channel.
c) Prior channel: When pressing the PTT key while the scan function is active the unit transmits
basically on the prior channel, i.e. any channel of the scanning list which your dealer can select.
d) Prior channel or actual channel: When the pressing of the PTT key occurs while the scan func­tion is stepping through the scanning list, the unit transmits on the prior channel. When the pres­sing of the PTT key occurs while the scan function is resting on a channel, the unit transmits on
this channel.

Note: Once a channel is selected for transmit mode, you can send your entire message on this
channel. After you have released the PTT key the unit will still stay for a dealer-set dwell time
between 0.5 and 5 s on this channel, before the channel scanning is restarted again.

Auxiliary functions of the TEAM PT-3208S

These functions must be installed into your transceiver by your dealer, before you can use them.
In the description below it is assumed that the functions are active. Ask your dealer for more
details.

1) Transmit time limiter
The transmit time limiter ( = time-out-timer ) has the effect of limiting the maximum time for con­tinuous transmitting on a channel. This transmit duration limit can be adjusted in steps between

0.5 and 10 minutes by your dealer. If the transmit time exceeds the actual transmit duration limit
during your message, the transmitter will shut off automatically, and you will hear a warning tone
in the speaker. To stop the warning tone and to reactivate the transmitter you have to release
briefly the PTT key.

ENGLISH

15

2) Busy channel lockout function
The lockout function for busy channels has the effect to prevent the unit from interfering with
other stations. If there is a station on the actual channel at the moment when you press the PTT
key, the transmitter will not be switched on. In this situation you will only hear a warning tone in
the speaker. When you release the PTT key the warning tone will be stopped and the set will
revert to receiving mode. You can only send if there is no station on the actual channel at the
moment when you press the PTT key.

3) Energy saving function
The unit is equipped with an energy saving function. This function is factory set in your unit. This
function works only in receive mode. It reduces the current consumption when no signal is
detect-ed on the actual channel and no the rotary channel selector is not turned for a longer peri­od. If you do not use the unit for a longer period of time, you should switch it off.

4) Additional muting function
The unit is also equipped with a possibility to suppress messages of unwanted operators on the
actual channel while the message of the partner station remains audible. To identify the wanted
radio messages there are two methods available: CTCSS and DQT.

CTCSS method ( = Continuous Tone Coded Squelch System )
The wanted radio message must contain a certain inaudible tone, which the CTCSS detecting
circuit of the receiving unit recognises and which can take the additional muting device out of ser­vice. In transmit mode the unit adds to its voice signal also a certain inaudible tone which will be
recognised by the CTCSS detecting circuit of the counter station’s receiver to open its additional
muting device.

DQT method ( Digital Quiet Talk )
The digital pulse detecting circuit of the receiving unit checks if the received signal contains any
digital pulses. If it has identified a certain sequence of digital pulses as the opening code of the
wanted message, the muting device lets the radio message pass from that moment on. In case
of sending DQT coded messages the unit transmits immediately, after the PTT key has been
pressed down, a certain sequence of digital pulses, too. These pulses will be recognised by the
digital pulse detecting circuit of the counter station’s receiver, which gives an order to the muting
device to let the radio message pass to the speaker from that moment on. The duration of the
sequence of digital pulses is very short, so you can start to speak without waiting after you have
pressed the PTT key.
Please take into account that other radio operators, who are not equipped with a CTCSS or DQT
coding/encoding device, or who don’t use it, can hear all your conversation if they are working
on the same channel like you and your counter operator.
Your dealer can install for each channel separately the CTCSS or DQT operation. It is also pos­sible to set at the same channel different operation types for receive and transmit mode. But if
you do not want the CTCSS or DQT operation at all, you can take it as well out of service.
If the CTCSS or DQT operation is installed in receiving mode on the actual channel, and if
there is a radio operator on this channel who uses either no CTCSS or DQT operation or a not
according one, you will see only the control lamp ( 2 ) lighting up green, but the speaker will be
silent. This shows you that the channel is occupied and that you should not transmit on this chan­nel for not disturbing the other station.
The CTCSS method allows your dealer to select one of 38 different inaudible tones to encrypt
your messages between you and the wanted radio operator. If you use the DQT method your
dealer will have 166 different digital codes to encrypt your messages between you and the want­ed radio operator.
The monitor key stops besides the noise suppression also a possible CTCSS or DQT operation
in the receiver . The monitor key function can be changed in that way by your dealer that only the
CTCSS or DQT operation in receiving mode is shut off, but not the noise squelch.

16

ENGLISH

General

1)Safety
The unit radiates RF energy in transmitting mode. To reduce the exposure to the lowest possi­ble value and to benefit the most of the set’s features, keep the following in mind:
In transmission mode, keep the unit in a vertical position at a distance of 2 inches away from your
face. Keep the antenna at a distance of at least 3 inch away from your head and your body.

2) Service
The condition of the accumulator must be tested from time to time. If the accumulator is weak a
short time after complete charge, it should be removed from the set. It can leak and damage the
device. Replace it by a new one.
Worn out accumulators do not belong into the waste bin, but must be returned to a suitable
collecting depot or to a special dealer, for the sake of the environment.
There are no user-adjustable or user-serviceable parts inside the radio. The casing must not be
opened. Independent repairs or adjustments must not be carried out, since each modification or
unauthorised intervention will immediately cancel all and any guarantee or repair claims, they are
also likely to result in non-conformity to ETS/EN regulations which will render the set to become
illegal.
In the event a defect becoming apparent, contact a properly equipped and authorised TEAM
dealer or TEAM directly.

3) Conformity
The transceiver TEAM PT-3208S complies with the rules of the European Directive R&TTE and
meets the European Telecommunication Standards EN 300 296, EN 300 086, EN 301 489-1/-5
and EN 60065.

4) Programmed Channels

Channel Transmit Frequency Encryption TX Reception Frequency Decryption RX Bandwidth

(MHz) (MHz) Narrow / Wide

1 446,00625 MHz 446,00625 MHz narrow
2 446,01875 MHz 446,01875 MHz narrow
3 446,03125 MHz 446,03125 MHz narrow
4 446,04375 MHz 446,04375 MHz narrow
5 446,05625 MHz 446,05625 MHz narrow
6 446,06875 MHz 446,06875 MHz narrow
7 446,08125 MHz 446,08125 MHz narrow
8 446,09375 MHz 446,09375 MHz narrow

9
10
11
12
13
14
15
16

ENGLISH

17

5) Programmed functions
Insert below the functions that your dealer has programmed into your transceiver.

Condition to Restart the Channel Scan Function Channel Scanning

Time Control Carrier Wave Control activated deactivated
Duration [ s ]

18

ENGLISH FRANçAIS

Transmit Channel during Active Channel Scan Function

First Channel First Channel or Prior Channel Prior Channel or

actual Channel actual Channel

Function of the Monitor Key

Out of Function Stopping briefly Stopping Stopping briefly

CTCSS & DQT CTCSS & DQT Noise Squelch

in toggle mode CTCSS & DQT

Transmit Time-Out-Timer

Duration [min]

6) Technical Data
PMR Frequency Range

Channel Frequency [ MHz ] Channel Frequency [ MHz ] Channel Frequency [ MHz ]

1 446.00625 2 446.01875 3 446.03125
4 446.04375 5 446.05625 6 446.06875
7 446.08125 8 446.09375

Channel spacing: 12.5 kHz
Radiated TX output power: 500 mW
Modulation type: 8K50F3E
Deviation: max. 2.5 kHz ( narrow )
RX sensitivity: + 14 dBµV/m ( narrow )

Audio output power: 0.56 W at 8 Ω at 10 % THD
Supply voltage: 5.5 – 7.5 V
Current consumption: TX: 490 mA

Professional radio communication:
Frequency range: 450 MHz – 470 MHz
Frequency step size: 6.25 kHz; 5 kHz
Channel separation: narrow: 12.5 kHz / wide: 25 kHz
TX output power: max. 5 W
Modulation type: FM
Deviation: narrow: 2.5 kHz / wide: 5 kHz
RX sensitivity: narrow: + 14 dBµV/m / wide: + 8 dBµV/m

Audio output power: 0.56 W at 8 Ω at 10 % THD
Supply voltage: 5.5 – 7.5 V
Current consumption: TX ( Low ): 490 mA; TX ( High ): 1.5 A
RX without power down mode: 60 mA
RX with power down mode: 30 mA
Dimsions ( cabinet ): W/H/D: 59 x 117 x 42 mm

Weight with Batteries and antenna: 322 g

This product is meant for distribution and sale in the following European countries:

Austria, Germany, Switzerland.

27

DQT-Codes
Code Code Code Code Code Code

D023I D114I D174I D315I D445I D631I
D025I D115I D205I D331I D464I D632I
D026I D116I D223I D343I D465I D654I
D031I D125I D226I D346I D466I D662I
D032I D131I D243I D351I D503I D664I
D043I D132I D244I D364I D506I D703I
D047I D134I D245I D365I D516I D712I
D051I D143I D251I D371I D532I D723I
D054I D152I D261I D411I D546I D731I
D065I D155I D263I D412I D565I D732I
D071I D156I D265I D413I D606I D734I
D072I D162I D271I D623I D612I D743I
D073I D165I D306I D431I D624I D754I
D074I D172I D311I D432I D627I

DQT-Codes
Code Code Code Code Code Code

D023N D114N D174N D315N D445N D631N
D025N D115N D205N D331N D464N D632N
D026N D116N D223N D343N D465N D654N
D031N D125N D226N D346N D466N D662N
D032N D131N D243N D351N D503N D664N
D043N D132N D244N D364N D506N D703N
D047N D134N D245N D365N D516N D712N
D051N D143N D251N D371N D532N D723N
D054N D152N D261N D411N D546N D731N
D065N D155N D263N D412N D565N D732N
D071N D156N D265N D413N D606N D734N
D072N D162N D271N D623N D612N D743N
D073N D165N D306N D431N D624N D754N
D074N D172N D311N D432N D627N

CTCSS-Töne • CTCSS tones • Fréquences des tons CTCSS :
Code Frequ. (Hz) Code Frequ. (Hz) Code Frequ. (Hz) Code Frequ. (Hz) Code Frequ. (Hz)

1 67,0 10 94,8 18 123,0 26 162,2 34 218,1
2 71,9 11 97,4 19 127,3 27 167,9 35 225,7
3 74,4 12 100,0 20 131,8 28 173,8 36 233,6
4 77,0 13 103,5 21 136,5 29 179,9 37 241,8
5 79,7 14 107,2 22 141,3 30 186,2 38 250,3
6 82,5 15 110,9 23 146,2 31 192,8
7 85,4 16 114,8 24 151,4 32 203,5
8 88,5 17 118,8 25 156,7 33 210,7

TEAM PT3208S

electronic

for sale and use in :

Austria, Germany and Switzerland

Team Electronic GmbH

Bolongarostrasse 88

65929 Frankfurt am Main

Tel. 069 - 30 09 50 - 0

Fax 069 - 31 43 82

eMail [e-mail]

Web Seite www.team-electronic.de