Team Electronic TeCom-PRO Freenet, PR8102, TeCom-PRO, PR8029, TeCom-PRO Commercial User Manual

Download

Page 1

TeCom-PRO

FreeNet Funkgerät / Radio

Bedienungsanleitung Manual

TeCom-PRO

VHF Betriebsfunkgerät Commercial Radio

Page 2

Advanced Functions 31 Channel Mode 31

Scan all Available Channels (01) 31 Scan Priority Channels (02) 31 VOX Sensitivity (03) 31 TX Power (04) 32 Squelch (05) 32 Scrambler (06) 32 Background Light On / Off (07) 32 Background Color (08) 33 Conrmation Tone On / Off (09) 33 ANI (Automatic Number Identication) On / Off (10) 33 Key Lock (11) 33 Time-Out-Timer (12) 34 Scan Types (13) 34 Voice Annunciation (14) 34 Name (15) 34

Frequency Mode 35

RX-TX Frequency Difference (15) 35 CTCSS-Code RX and TX (16) 35 CTCSS-code RX (18). 35 CTCSS- / DCS-Code RX (17) 35 CTCSS/DCS TX-Code (18) 36 +/- Shift Up (19) 36 Frequency Steps (20) 36

Programming Mode 36

1. Channel Number 37

2. Reception Frequency 37

3. CTCSS/DCS RX-Code 37

4. Transmitting Frequency 38

5. CTCSS/DCS TX-Code 38

6. Busy Channel Lockout 38

7. Priority Channel Scan 38

8. TX Power HI/LO 38

9. Bandwidth 38

10. Name 38

CCIR Selective Call 38 Diagrams 39

Functions in Channel Mode 39 Additional Functions in Frequency Mode 40

CTCSS/DCS Codes 41

Specications 41

GENERAL 26

Unpacking 26 Maintenance 26 Legend - Control Elements and Other Parts 27 - 28

MANUAL 29

Basic Functions 29

Antenna 29 Battery Pack 29 Turn Power On / Off 29 Adjustment of Volume 29 Transmit 29 Emergency Alarm 29 Calling Tone 29 Key Lock 29 Frequency Inversion 30 Store Manually Set Frequency 30 Delete Stored Frequency 30 Delete all Settings of the Frequency Mode 30 Delete all Settings 31

1750 kHz Call Tone 31

Dear Customer, Thank you for purchasing a TEAM brand handheld transceiver. Please read his manual to ensure

proper use and a long life of your radio. The TeCom-PRO is available in two versions: TeCom-PRO Freenet – Item No. PR8102

The FreeNet version is only permitted in Germany. It does not require a licence and no fees apply. It is programmed with the six FreeNet channels on 149 MHz and a Tx power of max. 500 mW. With this version, it is not permitted to change any settings of the frequencies, the Tx power or the bandwidth.

TeCom-PRO (COM) - Item No. PR8029 The commercial version requires a licence, to be obtained at your country’s governmental agency in charge of telecommunication, and fees apply. The radio can only be programmed to the approved frequencies, Tx power and bandwidth by an authorized TEAM dealer.

For the list of countries, where the TeCom-PRO can be used, see the declaration of conformity. Thank you & best regards,

TEAM Electronic GmbH

Page 3

GENERAL

Unpacking

Carefully unpack the giftbox and check the content for completeness. If any items are missing or damaged, please contact your dealer immediately.

Scope of Delivery: 1 x TeCom-PRO 1 x SMA-Antenna 1 x Battery Pack 1 x Charger-Mould and Adapter 1 x Belt Clip 1 x Manual

Maintenance

Please follow these instructions for your radios longevity.

 Please do not open the radio. Damages may occur.  For charging the battery pack of the TeCom-PRO, please use only the charger that is included

in the scope of delivery.  Do not expose the radio to direct sunlight or heat. High temperatures can shorten the life of certain electronic parts in your radio. Further, plastic parts can be deformed.

 Please do not store the radio in dusty or dirty areas.  Always keep the radio dry. Please do not expose your TeCom-XP to liquids of any kind, corriosion of the

electronic circuits can occur.  In case the radio omits smoke or an unusual smell or is very hot, please turn the radio off and remove the battery pack instantly. Contact your dealer immediatly.

 Never transmit without an antenna. A damage of the power amplier may occur. 

Features

+ Max. Output Power FreeNet : 500 mW / VHF COM : 5 Watt + 128 Programmable Channels + Channel Spacing FreeNet : 12.5 kHz / Commercial Version 12.5 / 25 kHz

+ Automatic Numbering Identication (ANI) code

+ VOX-Function + All Channel Scan + Priority Channel Scan + Scrambler Function + Three Color LCD Backlight + Emergency Alarm + PC-Programmable + 50 CTCSS and 105 DQT Codes ( Normal / Inversed ) + Time-Out-Timer ( TOT ) + Busy Channel Lockout + CCIR 5-Tone Selective Calling

1 Antenna 2 Rotary Channel Selector 3 ON / OFF and Volume Knob 4 Speaker 5 Microphone 6 LC Display

7 PTT key 8 Monitor key 9 Call key 10 Battery Pack Lock

10 Battery Pack Lock

11 Jacks for external Ear- / Microphone

12 Battery Pack

Legend - Controls and Other Parts

Page 4

MANUAL

Basic Functions

Antenna

Place the base of the antenna into the SMA socket and turn the antenna clockwise until it ts tight.

To remove the antenna turn the antenna counter-clockwise.

Battery Pack

To attach the battery pack to the radio, place the leading parts into the holes an the bottom of the radio. Next, press the battery pack at the upper part (belt clip holder) against the radio until the battery pack locks in. To remove the battery pack from the radio, push down the clips on the left and right side of the battery

pack with your thumb and index nger until the battery pack is released.

Turn Power On / Off

To power on the radio, turn the On / Off switch clockwise beyond the barrier. A beep tone will be heard followed by the words „Power On“ and the actual channel number if the functions beep tone and voice annunciation have been activated. In the LC display all available function symbols can be seen for approximatly 1 seconds. To power off the radio, turn the On / Off switch counter-clockwise above the barrier.

Adjustment of Volume

To be able to set a comfortable volume level after turning the radio on, keep holding the monitor key while adjusting volume to the desired level.

Transmit

To transmit, keep pressing the PTT key until you are nished with your message. For best sound

qualitiy, speak with a middle loud voice with a distance of approximately 4 inches to the microphone. During transmission, the control LED lights up red. After release of the PTT key, the radio return to reception mode.

Emergency Alarm

To send the emergency alarm, press the monitor key and the call key simultaneously. The alarm will sound on the transmitting radio and on all receiving radios that are set to the same channel. To stop the emergency alarm press the PTT key.

Calling Tone

To send a calling tone, hold the calling tone key for 2 seconds. Receiving radios set to same channel and code will receive the calling tone.

Key Lock

To acitvate the key lock function, hold the the key lock key for 2 seconds. In the LC display a key symbol will appear in the lower right corner. When the key lock function is activated, only the PTT-, monitor- and calling keys are available. All remaining functions are disabled. To deactivate the key lock function, please hold the key lock key [* LOCK] for approximately 2 seconds. In the display, „UNLOCK“ will appear for a short while until the key symbol dissappears.

Key Pad: 13 Menu ( MENU )

14 Conrmation ( ENTER )

15 Multi Functional Key ( VFO / MR ) 16 Scan ( 1 SCAN ) 17 Priority Scan ( 2 PRI ) 18 VOX ( 3 VOX ) 19 TX Power ( 4 POWER ) 20 Squelch ( 5 SQL ) 21 Scrambler ( 6 SCR ) 22 Background-Light On / Off / Auto ( 7 LED ) 23 Background-Light Color ( 8 COLOR ) 24 Multi-Tone ( 9 BEEP ) 25 Keylock ( *LOCK ) 26 ANI-Code ( 0 ANI ) 27 Frequency Reverse

Page 5

Frequency Inversion

This function is only useful for the commerical radio version. To inverse the transmission and receiption frequency, hold the frequency-inversion key [# T-R] for about 2 seconds. The letter R will be visible in the upper row of the LC display. To deactivate the frequency inverse function, hold the frequency inversion key [# T-R] until the letter R in the LC display disappears. Attention:

Channel- / Frequency-Mode Switch

The TeCom-XP PRO can be switched between the channel mode and the frequency mode by holding

the conrmation key [ENTER] when powering on the radio. This feature is only available in the

commercial version. Channel Mode

The programmed channel number is displayed (CH--001 - CH--128). Frequency Modes

The actual frequency is shown in the display. There are two different frequency modes available. To switch between these two modes press the VFO/MR key [VFO/MR].

manual : the frequency can be set via key pad or by the rotary channel selector. programmed : the programmed frequency can be seen in the middle of the display. On the right side, the channel number is shown. The channels are changed with the rotary channel selector.

Store Manually Set Frequency

This feature is only available in the commercial radio version.

In the manual frequency mode, select the frequency that you want to store. Press the menu key [MENU], followed by the VFO/MR key [VFO/MR]. The channel number on the right side starts blinking. Set the channel number where the frequency should be stored with the rotary channel selector and

conrm your entry by pressing the VFO/MR key [VFO/MR].

Delete Stored Frequency

This feature is only available in the commercial radio version.

In the programmed frequency mode, power the radio off. Hold the VFO/MR key while turning the radio back on. The symbol „DEL?“ appears in the display and the channel number on the right side starts

blinking. Set the channel to be deleted with the rotary channel selector and conrm your selection with the conrmation key [ENTER]. The symbol „YES ?“ appears in the display. To delete the channel press the conrmation key [ENTER]. For a short time the symbol „DELETE“ shows in the display.

More channels can now be deleted if necessary. To leave the delete mode, press the menu key [MENU] or the VFO/MR key [VFO/MR ].

Delete all Settings of the Frequency Mode

This feature is only available in the commercial radio version.

Hold the menu key [MENU] while powering the radio on. The symbol „RESET?“ appears in the LC

display. Conrm your selection by pressing the conrmation key [ENTER] and select the option

„VFO ?“ with the rotary channel selector. Delete all settings of the frequency mode by pressing the

conrmation key [ENTER].

Delete all Settings

This feature is only available in the commercial radio version.

Hold the menu key [MENU] while powering the radio on. The symbol „RESET?“ appears in the LC

display. Conrm your selection by pressing the conrmation key [ENTER] and select the option „FULL?“ with the rotary channel selector. Delete all settings by pressing the conrmation key [ENTER].

1750 kHz Call Tone

The 1750 kHz Call Tone, for repeater operation, can be send by holding the orange button while pressing the PTT key (for ham radio).

Advanced Functions Channel Mode

In the following, the advanced functions, their parameters and the menu navigation will be explained. The three keys above the numerical key pad ( [MENU], [ENTER] and [VFO/MR] are used for the navigation through the menu.

[MENU] opens the menu. To select a menu function, press one of the numerical keys, which have menu function.

[ENTER] conrms your selection.

[VFO/MR] closes the menu. The actual selection is displayed. TeCom-PRO contains 21 functions in total. The functions 1 - 10 can

be selected via the keypad or the rotary channel selector, while the functions 11 - 21 can only be set with the rotary channel selector.

Scan all Available Channels (01)

To scan all available channels, starting from the current channel, press the menu key [MENU] followed by the channel scan key [2 SCAN]. On occupied channels, the scan function stops. When and how the scan function continues, depends on the setting of Scan Types (see further down).

To stop the scan function press the PTT key or the conrmation key [ENTER].

Scan Priority Channels (02)

All programmed channels can be added to the scan list. The function Scan Priority Channel scans only the channels of the scan list. Channels can be added to the list via the software or the programming mode (step #7). To activate the Priority Channel Scan press the menu key [MENU] and the Priority Scan Key [1 SCAN]. All channels of the scan list are constantly scanned in ring mode for signals. How the scan function reacts once an occupied channel is detected, depends on the setup of the function Scan Type (see below).

To deactivate the priority scan function press the PTT key or the conrmation key [ENTER].

VOX Sensitivity (03)

The VOX sensitivity consists of 9 levels with increasing sensitivity from 1 to 9. To turn off the VOX function, set the value „OFF“. To set the VOX function press the menu key [MENU] followed by the VOX key [3 VOX]. The display reads „VOX ?“. To enter the VOX mode press the conrmation key [ENTER]. Now, set the desired

value via the key pad or the channel selector. Store your selection by pressing the conrmation key

[ENTER] and the VFO/MR key. To leave the menu press the VFO/MR key again.

Page 6

TX Power (04)

You can select between the TX powers HI and LO. The change of setting affects all channel. To change the transmit power for an individual channel see instructions for programming mode (step #8). In the freenet version, the programmed value for the low TX power (LO) is 300 mW and for the high TX power (HI) 500 mW. The TeCom-PRO has a maximum transmit power of 5 Watt. For the commercial version, the authorized TEAM dealer can set the values for TX-Power Low (LO) and TX-Power High (HI) via software according to the permit. To set the desired transmit power for the selected channel, press the menu key [MENU] followed by the TX power key [4 POWER]. The display reads „POW ?“. Conrm your selection with the conrmation key [ENTER] and set the desired value (H / L) with the channel selector. To store the conrmation key [ENTER] and set the desired value (H / L) with the channel selector. To store the setting press the

conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press VFO/MR [VFO/MR] again.

Squelch (05)

The TeCom-PRO contains a 9-level squelch function (1 - 9). The higher the number the more sensitive the squelch is. To deactivate the squelch function set the value 0. To set the squelch level press the menu key [MENU] followed by the squelch key [5 SQL]. The display reads „SQL ?“. Conrm your selection by pressing the conrmation key [ENTER] and set the desired value via the keypad or the channel selector.

Store the setting by pressing the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

Scrambler (06)

The scramber function distorts the signal with the effect that only two radios with activated scrambler function can clearly communicate. All others will hear the signal „scrambled“. To activate / deactivate the scrambler function press the menu key [MENU] followed by the scrambler key [6 SCR]. The display reads „SCRM ?“. Conrm your selection by pressing the conrmation key

[ENTER] and make your selection with the channel selector. To store the setting press the conrmation

key [ENTER] followed by the VFO/MR key [VFO/MR]. To leave the menu press the VFO/MR key.

Background Light On / Off (07)

For the background light of the LCD, there are three possible settings: ON : The background light is continually on.

OFF : The background light is off. AUTO: After powering on, turning the channel selector, or pushing any of the keys the LC display will be alluminated for approximately 8 seconds.

To set the background light press the Menu key [MENU] followed by the background light key [7 LED]. The display reads „LED ?“. Conrm your selection by pressing the conrmation key [ENTER] and set your selection (ON / OFF / AUTO) with the rotary channel selector.

To store the setting and leave the menu, press the conrmation key [ENTER] once, followed by

pressing the VFO/MR key [VFO/MR] twice.

Background Color (08)

There are three different colors available for the background light : LIGHT 1 : Purple

LIGHT 2 : Orange LIGHT 3 : Blue

To set the desired color press open the menu by pressing the menu key [ MENU ] followed by the

background color key [ 8 COLOR ]. The display reads „ LIGHT ?“. Conrm this selection by pressing the conrmation key [ ENTER ] and make your selection with the rotary channel selector. Store your setting by pressing the conrmation key [ ENTER ] followed by the VFO/MR key [ VFO/MR ].

To leave the menu press the VFO/MR [ VFO/MR ] key again.

Conrmation Tone On / Off (09)

To conrm your selection made by pressing keys or turning the channel selector, an acoustic conrmation tone can be activated. To activate / deactivate the conrmation tone open the menu by pressing the menu key [MENU] followed by the conrmation tone key [9 BEEP]. The display reads „BEEP ?“. Conrm your selection by pressing the conrmation key [ENTER] and make your selection (ON / OFF) with the channel selector. Store your setting by pressing the conrmation key [ENTER] followed by the VFO/MR key

[VFO/MR]. To leave the menu press the VFO/MR key [VFO/MR].

ANI (Automatic Number Identication) On / Off (10)

The ANI function is comparable to caller ID. If the transmitting radio has an ANI code and if this function is activated, the code can be seen in the display. The ANI code will be programmed with the software T-UP7. To activate / deactivate the ANI function press the menu key [MENU] followed by the ANI key [0 ANI]. The display reads „ANI ?“. Press the conrmation key [ENTER] and make your selection (ON / OFF) with the channel selector.

To store your selection press the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press the VFO/MR key [VFO/MR].

Key Lock (11)

There are two different key lock modes available.

Manual : To activate / deactivate the key lock function press the key lock key [* LOCK] for

approximately 2 seconds.

Auto : After 25 seconds after the last operation, the key lock will be activated automatically.

To deactivate the key lock, the key lock key needs to be pressed for approximately 2 seconds.

To set the desired function (Manual / Auto) press the menu key [MENU] and turn the channel selector until the symbol „KEYBO?“ appears in the display. Conrm your selection by pressing the conrmation key [ENTER] and make your selection with the channel selector.

To store your selection press the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press the VFO/MR key [VFO/MR].

Page 7

Time-Out-Timer (12)

To avoid overly transmitting, the TeCom-PRO is equipped with the Time-Out-Time feature (TOT). The following settings are available : OFF; 30s, 60s, 90s, 120s, 150s, 180s, 210s, 240s and 270s.

To set the Time-Out-Timer open the menu by pressing the menu key [MENU] and turn the channel selector until the symbol „TOT ?“ appears in the display. Conrm your selection with the conrmation key [ENTER] and set the desired value with the channel selector.

To store your selection press the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press the VFO/MR key [VFO/MR].

Scan Types (13)

How the scan function reacts once an occupied channel is detected, is determined by the choosen Scan Type. There are three different types available :

TO : Time-Operated-Scan The radio stays on the channel where a signal has been detected for a certain time, to be programmed with the software, regardless if the signal continues or ends.

CO: Carrier-Operated-Scan The radio remains on the channel until the carrier signal ends. Then scanning continues.

SE: Search-Scan The scan function stops once a signal has been detected and stays on the channel.

To set the scan type open the menu with the menu key [MENU] and turn the channel selector until the display reads „SCANS?“. Conrm your selection with the conrmation key [ENTER] and make your selection (TO / CO / SE) with the channel selector.

To store the setting press the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press the VFO/MR key [VFO/MR].

Voice Annunciation (14)

All changes of settings can be announced in english or german language. The language has to be selected via the software. To activate/deactivate this function press the menu key [MENU] and turn the channel selector until the symbol „VOICE?“ appears in the display. Make your selection (ON / OFF) with the channel selector.

To store the setting press the conrmation key [ENTER] followed by the VFO/MR key [VFO/MR].

To leave the menu press the VFO/MR key [VFO/MR].

Name (15)

It is possible to program a name for the selected channel in the programming mode (step #10). To make this name visible in the display the Name-Function has to be activated. This function is only available in the channel mode. To activate / deactivate this function press the menu key [MENU] and turn the channel selector until the symbol reads „NAME?“. Make your selection (ON / OFF) and store your selection by pressing the menu key [MENU] followed by the VFO/MR key [VFO/MR]. To leave the menu press the VFO/MR key [VFO/MR].

Frequency Mode

ATTENTION: The following functions are only available in frequency mode. Due to governmental regulations, no frequency mode is available in the FreeNet version.

In the frequency mode, you can switch between the programmed frequency, with the channel number shown on the right side of the display, and the freely programmable frequency. To switch between those two modes press the VFO/MR key.

In the mode of the freely programmable frequency you can set any frequency, within the given range (VHF: 136 - 149 MHz) in steps of 5kHz / 6.25kHz / 10kHz / 12.5kHz / 25 kHz. More information about how to set the frequency steps can be found in the paragraph Frequency Steps (20).

Some of the following functions work differently, depending on the selected mode.

RX-TX Frequency Difference (15)

With this function you can read the difference between the reception and the transmitting frequencies, in the Programmed Frequency Mode. If the transmitting frequency is higher than the reception frequency

Set the radio to Programmed Frequency Mode. Press the menu key [MENU] and turn the channel selector until the display reads „DIFFR?“. Then, press the enter key [ENTER]. The difference between reception frequency and transmitting frequency is displayed.

To leave the menu press the conrmation key [ENTER].

CTCSS-Code RX and TX (16)

In the freely programmable frequency mode, the same CTCSS code can be programmed for transmission and reception with this function. In the freely programmable frequency mode, press the menu key [MENU] and turn the channel selector until the display reads „C--CDC?“. Press the enter key [ENTER] and select one of the 50 available

CTCSS codes. To turn off the CTCSS function select OFF. To conrm your selection press the enter key [ENTER] or wait a few seconds for automatic conrmation.

Hint : Any change of setting in this function will adapted the setting in CTCSS-code TX (17) and CTCSS-code RX (18).

CTCSS- / DCS-Code RX (17)

To read the CTCSS- / DQT-RX-code in the Programmed Frequency Mode, press the menu key [MENU] and turn the channel selector until the display reads „R--CDC?“. Conrm your selection by pressing the enter key [ENTER]. The programmed CTCSS code for the reception mode is displayed.

In the mode of the freely programmable frequency, one of the 50 available CTCSS codes can be programmed for the RX mode. Press the menu key [MENU], select the option „R--CDC?“ with the channel selector and conrm your selection by pressing the enter key [ENTER]. Next, select one of the 50 available CTCSS codes for

the RX mode. Conrm your selection by pressing the enter key [ENTER].

Page 8

CTCSS/DCS TX-Code (18)

The setup of this functions follows the aforementioned procedure, described in CTCSS/DCS RX-Code (18).

+/- Shift Up (19)

In the mode of the freely programmable frequency, the transmission frequency can be quickly shifted for 1 MHz up or down of the receiving frequency with this function. To shift the transmission frequency press the menu key [MENU] and select the option „S--D“ with

the channel selector. Conrm your selection with the conrmation key [ENTER]. Select one of the

following settings : S-D O: no shift

S-D + : shifted up S-D - : shifted down

Conrm your selection with the conrmation key [ENTER], followed by pressing the VFO/MR key

[VFO/MR] twice.

Frequency Steps (20)

In frequency mode, press the menu key [MENU], select the option „STEP?“ by turning the channel

selector and conrm your selection with the conrmation key [ENTER]. The following settings are available : 5kHz / 6,25kHz / 10kHz / 12,5kHz / 25kHz. To conrm the selection press the conrmation key [ENTER] once and the VFO/MR key [VFO/MR] twice.

Bandwidth (21)

There are two bandwiths available : narrow ( 12.5 kHz ) and wide ( 25 kHz ). In frequency mode press the menu key [MENU] and select the option „N/W“ with the channel selector.

Press the conrmation key [ENTER] and select the desired option (WIDE or NARROW) with the channel selector. To conrm the selection press the conrmation key [ENTER] once and the VFO/MR

key [VFO/MR] twice.

Programming Mode

The programming mode is only available for the commercial radio version. The TeCom-PRO contains a programming mode, that allows to program channels and their relevant settings. The programming mode can be activated via software.

The 10-step programming procedure of a channels contains the following settings:

1. Channel Number 6. Busy Channel Lockout

2. Receiving Frequency 7. Priority Channel Scan

3. CTCSS/DCS RX-Code 8. TX-Power High / Low

4. Transmitting Frequency 9. Bandwidth

5. CTCSS/DCS TX-Code 10. Channel Name

To enter the programming mode hold the monitor key [MONI] and the menu key [MENU] simultaneously while turning the radio on. The LC-display reads „SELF“. Start the programming procedure by pressing

the conrmation key [ENTER]. After programming a step, press the enter key [ENTER] to proceed to

the next step. The current step is displayed on the right side. After completion of all ten steps turn the radio off and back on again to return to operation mode.

Hints: > It is possible to program more than one channel once you are in programming mode. > It is not necessary to program all ten steps. Once steps 1 and 2 are programmed, the channel is stored and available in the operation mode. If the transmission frequency is left blank there is no transmission possible. All other parameters will be set by default. > To cancel the programming procedure of a channel press the menu key [MENU].

In the following the programming of all ten settings will be explained.

1. Channel Number

Set the channel number by turning the channel selector. The display reads „CH-XXX“ where XXX

stands for the channel number (001 - 128). To conrm your selection and move to the next step press

the enter key [ENTER].

2. Reception Frequency

Enter the RX-frequency for reception via the keypad or the channel selector. The radio only accepts entries within the given range of frequency (136 – 174 MHz). To change the frequency steps, press the call button. The steps 5kHz, 6.5 kHz, 10 kHz, 12.5 kHz and 25 kHz are available. The setting of the reception frequency is the only mandatory entry.

To conrm your selection press the enter key [ENTER].

3. CTCSS/DCS RX-Code

There are 50 CTCSS and 105 DCS codes available. The digital DCS codes can be reversed, thus, there are two times 105 DCS codes available. To select one of the following options, press the keylock key [*LOCK].

OFF : No code has been selected

67.0 : CTCSS-coding system D023N : DCS-coding system - To invert the code press the inverse key [ # T-R ]. the display will read D023I, with I standing for inverted.

After setting a coding system, select a code by turning the channel selector and conrm your selection by pressing the conrmation key [ENTER].

4. Transmitting Frequency

To program the transmitting frequency follow the procedure as described under 2. Reception Frequency. An entry is not mandatory but in this case no transmission will be possible on this channel.

To conrm your selection press the enter key [ENTER].

5. CTCSS/DCS TX-Code

To program the CTSS/DCS code for the transmission frequency, follow the procedure as described under 3. CTCSS/DCS RX-Code.

To conrm your selection press the enter key [ENTER].

If no transmitting frequency ( 4. ) has been programmed, this step will be skipped.

Page 9

6. Busy Channel Lockout

This function prevents transmission on occupied channels. The following options are available: OFF : Function deactivated

1 : Signal – Is a signal received, transmission will be blocked until the signal ends, regardless of the used code. 2 : CTCSS/DCS – Transmission is only blocked if the CTCSS/DCS code of the incoming signal is identical to the own code.

Make your selection by turning the channel selector and conrm by pressing the enter key [ENTER].

The defaut setting is OFF.

7. Priority Channel Scan

Decide if the channel should be added to the priority channel scanning list or not. The options ADD and DEL can be selected with the channel selector. The entry will be stored once the enter key [ENTER] has been pushed. The default setting is YES.

8. TX Power HI/LO

One of the two TX powers (HI and LO), which can be set by your dealer via software, can be

assigned the channel. Make your selection with the channel selector and conrm by pressing the

enter key [ENTER].

9. Bandwidth

On of the following options can be set with the channel selector: W : Wide – 25 kHz

N : Narrow – 12.5 kHz

Conrm your selection by pressing the enter key [ENTER]. The default setting is WIDE.

10. Name

Instead of the default channel number, a channel name can be edited. The name can be composed of max. six digits. The character is to be selected with the channel

selector. After conrming the selection by pressing the number key [# T-R], the next digit can be set.

The following symbols are available : Digits 0 -9 Hyphen ( - )

Letters A – Z Empty Space

End the name programming procedure by pressing the conrmation key [ENTER ].

All ten available parameter have been programmed. To return to operation mode, turn the radio off and then back on. To continue programming other channels start from step 1 again.

CCIR Selective Call

This function has to be programmed via software. More information about the possible settings can be found in the manual of the software.

A selective call to one specied radio can be sent prior to the signal. The caller ID is displayed on the

receiving radio.

SCAN ?

Channel Scan

All Programmed Channels

ENTER

To End Press

ENTER

NAME?

Settings Channel Name :

ON / OFF

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

VOICE?

Settings Annunciation :

ON / OFF

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

SCANS?

Settings Scan Types :

TO / CO / SE

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

TOT ?

Settings Time-Out-Timer :

OFF, 30 - 270s

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

KEYBO?

Settings Keylock :-

MANUAL, AUTO

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

ANI ?

Settings ANI :

ON / OFF

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

BEEP ?

Settings Beep Tone :

ON / OFF

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

LIGHT ?

Settings Backlight Color :

1 / 2 / 3

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

LED ?

Settings Backlight :

AUTO / ON / OFF

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

SCRM ?

Settings Scrambler :

OFF / ON

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

SQL ?

Settings Squelch :

0 - 9

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

POW ?

Settings TX-Power :

H / L

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

VOX ?

Settings Sensitivity :

OFF, 1 - 9

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

PRI ?

Channel Scan

Priority Scan List

ENTER

To End Press

ENTER

Channel Selector

Diagram

Functions in Channel Mode

Page 10

Additional Functions in Frequency Mode

N/W ?

Settings Bandwidth :

NARROW/WIDE

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

STEP?

Settings Frequency Steps:

5/6,25/10/12,5/25kHz

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

S-D ?

Settings TX Shift :

0 / + / -

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

T-CDC ?

CTCSS TX :

OFF, 67,0 - 254,1 Hz

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

R-CDC?

CTCSS RX :

OFF, 67,0 - 254,1 Hz

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

C-CDC ?

CTCSS TX & RX :

OFF, 67,0 - 254,1 Hz

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

DIFFR?

Settings TX-RX

Difference : 0 - 99,995 MhZ

ENTER

To store setting and leave

menu press VFO/MR twice

Channel Selector

General Range of Frequency : FreeNet 149.0250 - 149.1125 MHz VHF COM 136 - 174 MHz Operating Temperature : -20°C ~ +50°C Power Supply : DC 7.2 V Mode : Simplex or Semi-Duplex Dimensions : 100 mm x 55 mm x 32 mm ( Antenna not included ) Weight : 220 g ( incl. Battery Pack )

Specications

Page 11

Page 12

TeCom-PRO

Service :

TEAM Electronic GmbH

Bolongarostrasse 88

D-65929 Frankfurt am Main

fon ++49 - 69 - 300 90 500

fax ++49 - 69 - 31 43 82

team-electronic@t-online.de

www.team-electronic.de

For Use and Sale in :

TeCom-PRO FreeNet (PR8102)

Germany

TeCom-PRO Commercial (PR8029)

Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Great Britain, Greece, Hungary, Italy,

Lithuania, Luxembourg, the Netherlands,

Norway, Poland, Portugal, Spain, Sweden