HL-2S
HDMI Extender System
with HDBaseT-Lite and ARC
Installation Manual
HDBaseT
Firmware
Update
HDMI In ARC SPDIF Out
In
IR
HDMI Extender
Out
HL-2S TX
with HDBaseT-Lite™
HDBT
HDMI
Power
Power In
+
24VDC Only
Transmitter
Audio
Out
L R
HL-2S Installation Manual
Table of Contents
Introduction .............................................3
Kit Contents .............................................4
Feature Set .............................................5
Specications ...........................................6
Transmitter Connections ...................................7
Receiver Connections .....................................8
Transmitter Functions .....................................9
Reciever Functions ......................................10
Troubleshooting .........................................11
IR Connection Diagram (Any) ...............................12
IR Connection Diagram (12V Powered) .......................13
Warranty ..............................................14
2
HL-2S Installation Manual
Introduction
INTRODUCTION
Thank you for purchasing Transformative Engineering’s HL-2S HDMI Extender Kit. This
product incorporates many advanced technologies to accomplish full-function, 1.4a -
2.0 HDMI compliant extension of the High Denition MultiMedia Interface protocol over
one length of Category 5e/6/7 wire. Among these is certied HDBase-T technology,
licensed here. This unique conversion of HDMI signals provides for the most reliable,
stable and predictable method to transfer all HDMI requirements. More information
on this technology may be found at the HDBase-T website, www.hdbaset.org . We are
proud to be an early Adopter Member of the Alliance.
Proper connection and attention to limitations of this product will provide secure,
reliable, and predictable results. The most important variable to success will depend on
wire chosen as the interconnection between our Transmitter and Receiver. All Category
wire is not created equal. It is vital that care is taken at all times to avoid kinks, crimps,
nicks, and other abuse of the wire and jacket. Also, we highly recommend that all wire
be sweep tested before and after installation to insure full bandwidth is not impaired. A
sweep-test generator, such as the Fluke CableIQ Qualication Tester, or its equivalent,
is suggested. Please be sure to specify Category 5e, or better, cable that meets a
minimum of 400MHz bandwidth. Typical high-quality Category 6 cable performs from
550-850 MHz, and Category 7 cable should pass 1GHz or more.
This HDMI Extender will meet our rated specications using CAT 5e/6/7 UTP cable. It
will also perform with STP (shielded twisted pair) cable as well. MOST FAILURES OR
INCONSISTENT PERFORMANCE ARE THE RESULT OF INFERIOR WIRE OR IMPROPER
TERMINATIONS. The rst step in diagnosing problems with this product should center
on the connection and choice of the wire used.
Please follow the instructions and diagrams shown in this Manual. Any questions
should be directed to your Dealer, Distributor, or to our Technical Department. Our
Contact information is:
Transformative Engineering, Inc.
194 Vanderbilt Ave.
Norwood, MA 02062-5000
Telephone: 781-769-6410
Fax: 781-255-0975
Email: info@transformativeengineering.com
3
HL-2S Installation Manual
Kit Contents
KIT CONTENTS
(1) HL-2S Transmitter Unit (HL-2STX)
(1) HL-2S Receiving Unit (HL-2SRX)
(1) 24V .75A DC Power Supply
(1) SMA-1 IR Adapter Dongle
(4) Integrated Metal Mounting Tabs
(1) User Manual
4
HL-2S Installation Manual
Features
FEATURE SET
• HD / UHD4K HDMI Extender
• Full HDCP Security, HDCP2.2 compliant
• Audio Return Channel (ARC)
• Optical Digital Audio Path
• EDID Protocol Integrity
• Bi-Directional IR Pass-Thru with Power for Active Pickup
• 24V Power Supply for Robust Performance
• Single Power Supply at Either the Tx OR Rx unit powers both
• Extruded Aluminum Construction with Flexible Mounting Options
• 2-Channel Analog Audio Derived from TV’s ARC or TOSLINK
Optical Output
5
HL-2S Installation Manual
Specications
SPECIFICATIONS
Input Signal: HDMI Version 1.0 thru 2.0
IR Signal – Pass Thru (Industry Compatible)
IR Powered Pickup – Ring (Ground), Tip (Signal),
Sleeve (+12VDC) (see page 8)
Video Formats Supported: 480i/576i/480p/576p/720p/1080i/1080p/
UHD4K-60Hz-4-2-0/UHD4K-30Hz-4-4-4
Audio Formats Supported: All HDMI Supported Formats, including DTSHD,
Dolby-HD, DVD-A, Dolby TrueHD, 8-CH
LPCM
Output Signal: HDMI Version 1.0 thru 2.0
IR Signal – Pass Thru (Xantech Compatible)
(See page 8)
Maximum Distance (with CAT6): 70 Meters (230 Feet), @ 1080p
40 Meters (130 Feet), @ UHD4K
Power Supply X1 (supplied): 24 VDC, .75A DC
Dimensions (Each): 5.75”W x 1.1”H x 3.75”D
Weight: 1.0 Lbs (Each)
6
TRANSMITTER
HL-2S Installation Manual
Transmitter Connections
1
8 5 7
6
1 HDMI Input
2 ARC Indicator
3 Digital Optical Out (SPDIF)
4 Analog Audio Out
5 Power Input (Choose One)
9 10 11 12
3 4 2
7 HDCP Indicator
8 HDBaseT Link Indicator
9 IRDA Out
10 IRDA In
11 Mini USB (Firmware Update)
6 Power Indicator
12 HDBaseT Link Connection
7
HL-2S Installation Manual
Receiver Connections
RECEIVER
1
8 5 7
1 HDMI Output
2 ARC Indicator
3 Digital Optical In (SPDIF)
5 Power Input (Choose One)
6 Power Indicator
3 2
9 10 11 12 6
7 HDCP Indicator
8 HDBaseT Link Indicator
9 IRDA Out
10 IRDA In
11 Mini USB (Firmware Update)
12 HDBaseT Link Connection
8
HL-2S Installation Manual
Transmitter Functions
TRANSMITTER FUNCTIONS - See pg 7
1 HDMI Input – Connect this to your HDMI Source – Cable Box, Disc Player, etc.
2 ARC Indicator – This light will illuminate whenever a completed audio signal
from ARC or the TOSLINK connection is established.
3 Digital Optical Out (SPDIF) – Connect to Optical in of Surround Receiver as an
alternative to ARC for improved sound from your SmartTV.
4 Analog Audio Out – This is a 2-channel decoded audio source derived from
the Audio Return Channel or TOSLINK Digital stream from the TV to an amplier.
5 Power Input – Utilizing the supplied 24V .75A supply, when connected at the
Transmitter side, No Power Supply is necessary at the Receiver side.
6 Power Indicator – This light indicates that power is being supplied to the
unit.Connection of the (included) Power Supply should illuminate this light on both
Transmitter and Receiver Units.
7 HDCP Indicator – This light shows that a valid HDMI connection has been
made, “handshake” has taken place, and there is a High Denition Copy Protect ag
in operation. Attempts to copy Digital content will not be allowed. Any connection
to a non-compliant Digital copy device will cause this light to go off, and will result
in the loss of signal.
8 HDBaseT Link Indicator – These lights show that communication has been
properly established with the HDBase-T Receiver. No other connections need be
made for these lights to indicate your connection is secure. If the “POWER” light is
not on, you should check that the power supply is properly connected.
9 IRDA Out – Used for connecting to an Infra-Red Emitter for controlling a device
at this end. The IR Signal would originate from the Receiver end either from a
Powered Pickup or an IR Pass-Thru. (See diagrams on pages 12 and 13)
9
HL-2S Installation Manual
Recievers Functions
10 IRDA In – Used for connecting to a 12V Xantech Compatible Powered Infra-
Red Pickup Device via 3-conductor mini-jack, or to IR encoded signal for PassThru to the IRDA OUT at the Receiver end. (See diagram on page 12 and 13 for
suggested use)
11 Mini USB (Firmware Update) – For Firmware updates (provided if
necessary) by Transformative Engineering. DO NOT attempt to connect this port for
any other reason. Loss of all operation may result.
12 HDBase-T Link Connection – Connect via Category 5e/6/7 cable to the HL-
2S Receiver Unit ONLY. DO NOT CONNECT THIS RJ-45 CONNECTOR TO ETHERNET.
DAMAGE TO THIS PRODUCT AND YOUR NETWORK MAY RESULT. Recommended
minimum length is 5 Meters up to our maximum rated specication of 70 Meters.
12a Audio Return Channel – Audio Return Channel (ARC) is incorporated into
the HDMI connector and serves to provide a pathway for the audio signal that
originates from the Display (TV) source. When utilizing ARC-enabled Smart TVs
to “stream” content from internet providers, the audio from that content may be
presented back to the head-end and into ARC-enabled Surround Receivers. This is
effectively a method for bi-directional use of the HDMI signal path. Only Audio from
the ARC-enabled TV may be sent over this method. Please refer to setup instructions
on your AV Surround Receiver and Television display for details.
RECEIVER FUNCTIONS - See Page 8
1 HDMI Output – Connect this to your Display device – TV, Projector, etc. All video
signals input to the HDMI Input on the Transmitter will appear here.
2 ARC Indicator – This light will illuminate whenever a completed audio signal
from ARC or the TOSLINK connection is established.
3 Digital Optical In (SPDIF) – Use the Optical output from a SmartTV as an
alternative to ARC for improved sound.
10
HL-2S Installation Manual
Troubleshooting
5 Power Input – Utilizing the supplied 24V .75A supply, when connected at the
Receiver side, No Power Supply is necessary at the Transmitter side.
6 Power Indicator – This light indicates that power is being supplied to the
unit. Connection of the (included) Power Supply should illuminate this light on both
Transmitter and Receiver Units.
7 HDCP Indicator – Refer to Item (7) above.
8 HDBaseT Link Indicator – Refer to Item (8) above.
9 IRDA Out – Used for connecting to an Infra-Red Emitter for controlling a device
at this end. The IR Signal would originate from the Transmitter end either from a
Powered Pickup or an IR Pass-Thru. (See diagrams on pages 12 and 13)
10 IRDA In – Used for connecting to a Powered Infra-Red Pickup Device (Xantech
compatible) via 3-conductor mini-jack, or to IR encoded signal for Pass-Thru to the
IRDA OUT at the Transmitter end. (See diagrams on pages 12 and 13)
11 Mini USB (Firmware Update) – For Firmware updates (provided if
necessary) by Transformative Engineering. DO NOT attempt to connect this port for
any other reason. Loss of all operation may result.
12 HDBase-T Link Connection – Refer to Item (1) above.
TROUBLESHOOTING
As mentioned previously, most malfunctions can be addressed by careful examination
of the Category cable terminations and suitability of the UTP cable itself. Once the
“Link” lights are on, this system is operating normally. Lack of function should be
traced to a failure in HDMI interconnection cables or device settings. If all this has been
examined with no resolution of your problem, please contact our Technical Support
Department at 781-769-6410 or via email at: info@transformativeengineering.com.
11
HL-2S Installation Manual
IR Connection Diagrams
IR Pass Thru IR Connection
Diagram
UTP Cable
(Any) Pickup
HDBaseT
IR Signal
Firmware
Update
HDMI In ARC SPDIF Out
In
IR
HDMI Extender
HDBT
Out
HDMI
Power
HL-2S TX
with HDBaseT-Lite™
Power In
+
Transmitter
Audio
Out
L R
24VDC Only
Power
Supply
for P/U
Connecting
Block
IR asher
(emitter)
SMA-1
Adapter
HDBaseT
Firmware
Update
HDMI Out ARC SPDIF In
12
In Out
IR
HL-2S RX
HDMI Extender
with HDBaseT-Lite™
HDBT
HDMI
Power
Power In
+
24VDC Only
Transmitter
IR Connection Diagrams
Powered Pickup IR Connection
Diagram
HDBaseT
HL-2S Installation Manual
Power In
Firmware
Update
In
HDBT
Out
IR
HDMI
Power
+
24VDC Only
Xantech-
Compatible
Pickup
IR asher
(emitter)
IR Signal
UTP Cable
HDMI In ARC SPDIF Out
HDBaseT
Firmware
Update
HDMI Out ARC SPDIF In
HL-2S TX
HDMI Extender
with HDBaseT-Lite™
In Out
IR
HL-2S RX
HDMI Extender
with HDBaseT-Lite™
HDBT
HDMI
Power
Transmitter
Audio
Out
L R
Power In
+
Transmitter
24VDC Only
13
HL-2S Installation Manual
Warranty
WARRANTY
Transformative Engineering, Inc. guarantees this product for Two Years
from your original purchase. We guarantee performance and operation to
published specications including all parts and labor. We do not warranty
against mis-use or abuse. To obtain warranty service, please contact our
Technical Support Department at 781-769-6410 or via email at: info@
transformativeengineering.com.
Transformative Engineering, Inc.
194 Vanderbilt Ave.
Norwood, MA 02062-5000
Telephone: 781-769-6410
Fax: 781-255-0975
Email: info@transformativeengineering.com
14
Loading...