Page 1
Programmable DC Power Supplies
3.3kW in 2U
Built in RS-232 & RS-485 Interface
Advanced Parallel Operation
Optional Interface:
Compliant LAN
IEEE488.2 SCPI (GPIB) Multi-Drop
Isolated Analog Programming
Page 2
GENESYS
TM
GEN 3.3kW SERIES POWER
SUPPLIES
USER MANUAL
GEN 3.3kW SERIES POWER
GEN8-400
TM
GENESYS
SUPPLIES
USER MANUAL
This Manual Covers Models:
GEN40-85
GEN200-16.5
GEN10-330
GEN15-220
GEN20-165
GEN30-110
GEN60-55
GEN80-42
GEN100-33
GEN150-22
GEN300-11
GEN600-5.5
Manual Supplement
For units equipped with IEEE488.2 (GPIB) Interface option,
refer to Manual IA586-04-01_.
For units equipped with LAN Interface option,
refer to Manual IA672-04-01_.
IA626-04-01-Rev. Q
Page 3
This information sheet was prepared based on People's Republic of China "Management Methods for Controlling Pollution Caused by
"SJ/T 11364—2006 Marking for Control of Pollution Caused by Electronic Information Products
As People's Republic of China "Management Methods for Controlling Pollution Caused by Electronic Information Products Regulatio
2002/95/EC
, inquiries concerning EU RoHS Directive
The date of manufacture
Part Name
GENESYS, GEN3.3KW POWER SUPPLY SERIES Product Weight
13Kg
Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent
Chromium (Cr6+)
Polybrominated
Biphenyls （PBB）
Polybrominated Diphenyl
Ethers（PBDE）
0.1wt% 0.1wt% 0.01wt% 0.1wt% 0.1wt% 0.1wt%
Case
OOOO O O
Plastic panel
OOOO O O
PCB's assembly XOOO O O
Inner metal parts OOOO O O
Inner cables OOOO O O
Accessories OOOO O OProvided in the package
○ : Indicates that the concentration values of toxic and hazardous substances in all "homogeneous materials" of respective parts and materials does not exceed the concentration limits
regulated by "SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products".
× : Indicates that the concentration value of a toxic or hazardous substance included in a "homogeneous part" of a respective part ot material exceeds the concentration limit regulated by
"SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products".
Information Concerning Inclusion of Toxic and Hazardous Substances
NotesConcentration Values of Toxic and Hazardous Substances/Elements (wt%)
Subpart Name
（2002/95/EC）, inquiries concerning EU RoHS Directive （2002/95/EC） information should be done separately.
GENESYS, GEN3.3KW POWER SUPPLY SERIES Product Weight
13Kg
Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent
0.1wt% 0.1wt% 0.01wt% 0.1wt% 0.1wt% 0.1wt%
OOOO O O
Plastic panel
OOOO O O
PCB's assembly XOOO O O
Inner metal parts OOOO O O
Inner cables OOOO O O
Accessories OOOO O O
: Indicates that the concentration values of toxic and hazardous substances in all "homogeneous materials" of respective parts
regulated by "SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Infor
: Indicates that the concentration value of a toxic or hazardous substance included in a "homogeneous part" of a respective p
"SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Product
NotesConcentration Values of Toxic and Hazardous Substances/Elements (wt%)
n"is a different legislation from EU RoHS Directive
Electronic Information Products Regulation"and
Ethers（PBDE）
The date of manufacture
Polybrominated Diphenyl
Polybrominated
Biphenyls （PBB）
".
Provided in the package
and materials does not exceed the concentration limits
mation Products".
s".
art ot material exceeds the concentration limit regulated by
（2002/95/EC） information should be done separately.
）
Part Name
Chromium (Cr6+)
Subpart Name
（
Case
○
×
Page 4
DECLARATION OF CONFORMITY
GEN3300W SERIES
We, TDK-Lambda Ltd., located at Haharoshet St. 56 Industrial Zone P.O.B. 500 Karmiel, Israel declare under our sole
responsibility that the GEN3300W series as detailed on the products covered sheet comply with the provisions of
the following European Directive and are eligible to bear the CE mark:
Restriction Of the use of certain Hazardous Substances Directive 2011/65/EU (RoHS2)
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Assurance of conformance of the described product with the provisions of the stated EC Directive is given
through compliance to the following standard:
Electrical Safety EN 60950-1:2006+A11+A1+A12
Electromagnetic Compatibility (EMC): EN 55022:1998+A1:2000+A2:2003
EN 55024:1998+A1:2001+A2:2003
EN 61000-3-3:1995+A2:2005
which cover testing to the following standards:
EN 55022:1998+A1:2000+A2:2003 Conducted Emissions Class A
Radiated Emissions Class A
EN 61000-3-3 :1995+A2:2005 Voltage Fluctuations
EN 61000-4-2 :1995+A1:1998+A2:2001 ESD AD: 8KV, CD:4KV
EN 61000-4-3 :2006 Radiated Immunity 3V/m
EN 61000-4-4 :2004 EFT/B Power leads: 2KV
Signal leads: 0.5KV
EN 61000-4-5 :2006 Conductive Surges Common mode: 2KV
Dierential mode: 1KV
EN 61000-4-6 :2007 Conducted Disturbances 3Vrms
EN 61000-4-8 :1993+A1:2001 Immunity to Mag. Field 1A/m
EN 61000-4-11:2004 Voltage Dips
Our European Representative in the EU is TDK-Lambda UK Limited, located at Kingsley Avenue, llfracombe,
Devon, EX34 8ES UK. Further, all products covered by this declaration are manufactured in accordance with
ISO9000:2008 which ensure continued compliance of the products with the requirements of the Low Voltage
Directive and EMC Directive.
Name of Authorized Signatory Martin Southam
Signature of Authorized Signatory
Position of Authorized Signatory Marketing Director EMEA
Date 3
rd
April 2013
Date Series rst CE marked 22 February 2006
Place where signed Ilfracombe, Devon, England
PRODUCTS COVERED SHEET FOR:
GEN3300W series
1. GEN3300W with one phase input 190-240VAC
2. GEN3300W with three phase input 190-240VAC
3. GEN3300W with three phase input 380-415VAC
with rated output 0-8VDC/0-400A up to 0-600VDC/0-5.5A and total output power equial or less 3300W
Optional modules:
1. IEEE (GPIB) module
2. Isolated analog (V/I) module
3. LAN module
4. USB module
TDK-Lambda Ltd., Industrial Zone P.O.B 500 Karmiel, IsraelTDK-Lambda Ltd., Industrial Zone P.O.B 500 Karmiel, IsraelTDK-Lambda Ltd., Industrial Zone P.O.B 500 Karmiel, Israel
Page 5
This page intentionally left blank
Page 6
TABLEOF CONTENTS
WARRANTY ..........................................................................................................................................
SAFETY INSTRUCTIONS.....................................................................................................................
GERMAN SAFETY INSTRUCTIONS ...................................................................................................
CHAPTER 1 GENERAL INFORMATION
....................................................................................
1.1 OPERATION MANUAL CONTENT .................................................................................................
1.2 INTRODUCTION .............................................................................................................................
1.2.1 General description ................................................................................................................
1.2.2 Models covered ......................................................................................................................
1.2.3 Features and options .............................................................................................................
1.2.4 Multiple output power system .................................................................................................
1.2.5 Control via the serial communication port ..............................................................................
1.2.6 Analog voltage programming and monitoring .................................................................. ......
1.2.7 Parallel operation ...................................................................................................................
1.2.8 Output connections ................................................................................................................
1.2.9 Cooling and mechanical construction ....................................................................................
1.3 ACCESSORIES ...............................................................................................................................
1.3.1 General ..................................................................................................................................
1.3.2 Serial link cable ......................................................................................................................
1.3.3 Misc. hardware .......................................................................................................................
1.3.4 AC cables ...............................................................................................................................
CHAPTER 2 SPECIFICATIONS
...................................................................................................
2.1 OUTPUT RATING ...........................................................................................................................
2.2 INPUT CHARACTERISTICS ..........................................................................................................
2.3 CONSTANT VOLTAGE MODE .......................................................................................................
2.4 CONSTANT CURRENT MODE ......................................................................................................
2.5 ANALOG PROGRAMMING AND MONITORING ............................................................................
2.6 PROGRAMMING AND READBACK ...............................................................................................
2.7 PROTECTIVE FUNCTIONS ...........................................................................................................
2.8 FRONT PANEL ................................................................................................................................
2.9 ENVIRONMENTAL CONDITIONS ..................................................................................................
2.10 MECHANICAL ..............................................................................................................................
2.11 SAFETY/EMC ...............................................................................................................................
2.12 SUPPLEMENTAL CHARACTERISTICS .......................................................................................
2.13 OUTLINE DRAWINGS .................................................................................................................
Pg.1
Pg.2
Pg.4
Pg.6
Pg.6
Pg.6
Pg.6
Pg.6
Pg.6
Pg.7
Pg.7
Pg.7
Pg.7
Pg.7
Pg.8
Pg.8
Pg.8
Pg.8
Pg.8
Pg.8
Pg.9
Pg.9
Pg.9
Pg.9
Pg.9
Pg.9
Pg.10
Pg.10
Pg.10
Pg.10
Pg.10
Pg.10
Pg.11
Pg.12
CHAPTER 3 INSTALLATION
.......................................................................................................
3.1 GENERAL .......................................................................................................................................
3.2 PREPARATION FOR USE ..............................................................................................................
3.3 INITIAL INSPECTION .....................................................................................................................
3.4 RACK MOUNTING ..........................................................................................................................
3.4.1 To install the power supply inarack .......................................................................................
3.4.2 Rack mount slides ..................................................................................................................
3.5 LOCATION MOUNTING AND COOLING .......................................................................................
3.6 AC SOURCE REQUIREMENTS .....................................................................................................
3.7 AC INPUT POWER CONNECTION ................................................................................................
3.7.1 AC input connector..................................................................................................................
3.7.2 AC input cord ..........................................................................................................................
3.7.3 AC input wire connection.........................................................................................................
3.8 TURN-ON CHECKOUT PROCEDURE ...........................................................................................
3.8.1 General ...................................................................................................................................
3.8.2 Prior to operation ...................................................................................................................
3.8.3 Constant voltage check ..........................................................................................................
3.8.4 Constant current check ..........................................................................................................
3.8.5 OVP check .............................................................................................................................
3.8.6 UVL check ..............................................................................................................................
3.8.7 Foldback check ......................................................................................................................
3.8.8 Address setting ......................................................................................................................
3.8.9 Baud rate setting ....................................................................................................................
Pg.13
Pg.13
Pg.13
Pg.13
Pg.13
Pg.13
Pg.14
Pg.14
Pg.14
Pg.14
Pg.15
Pg.15
Pg.15
Pg.16
Pg.16
Pg.16
Pg.17
Pg.17
Pg.17
Pg.17
Pg.18
Pg.18
Pg.18
Page 7
TABLEOF CONTENTS
3.9 CONNECTING THE LOAD ..........................................................................................................
3.9.1 Load Wiring ..........................................................................................................................
3.9.2 Current Carrying Capacity ...................................................................................................
3.9.3 Wire termination .................................................................................................................
3.9.4 Noise and Impedance Effects ..............................................................................................
3.9.5 Inductive loads .....................................................................................................................
3.9.6 Making the load connections ................................................................................................
3.9.7 Connecting single loads, local sensing (default) ..................................................................
3.9.8 Connecting single loads, remote sensing ............................................................................
3.9.9 Connecting multiple loads, radial distribution method ..........................................................
3.9.10 Multiple loads connection with distribution terminals .........................................................
3.9.11 Grounding outputs .............................................................................................................
3.10 LOCAL AND REMOTE SENSING .............................................................................................
3.10.1 Sensing wiring ...................................................................................................................
3.10.2 Local sensing .....................................................................................................................
3.10.3 Remote sensing .................................................................................................................
3.10.4 J2 sense connector technical information ..........................................................................
3.11 REPACKAGING FOR SHIPMENT .............................................................................................
CHAPTER 4FRONT AND REAR PANEL CONTROLS AND CONNECT
4.1 INTRODUCTION ..........................................................................................................................
4.2 FRONT PANEL CONTROLS AND INDICATORS ........................................................................
4.3 REAR PANEL ...............................................................................................................................
4.4 REAR PANEL SW1 SETUP SWITCH .........................................................................................
4.4.1 SW1 positions functions ......................................................................................................
4.4.2 Resetting the switch .............................................................................................................
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR ....................................
4.5.1 Making J1 connections ........................................................................................................
ORS
...............
Pg.18
Pg.18
Pg.18
Pg.19
Pg.20
Pg.20
Pg.20
Pg.23
Pg.23
Pg.23
Pg.24
Pg.24
Pg.25
Pg.25
Pg.25
Pg.26
Pg.26
Pg.26
Pg.27
Pg.27
Pg.27
Pg.29
Pg.30
Pg.31
Pg.31
Pg.32
Pg.32
CHAPTER 5LOCAL OPERATION
5.1 INTRODUCTION ..........................................................................................................................
5.2 STANDARD OPERATION ............................................................................................................
5.2.1 Constant Voltage Mode .......................................................................................................
5.2.2 Constant Current Operation .................................................................................................
5.2.3 Automatic Crossover ............................................................................................................
5.3 OVER VOLTAGE PROTECTION (OVP) ......................................................................................
5.3.1 Setting the OVP level ..........................................................................................................
5.3.2 Activated OVP protection indications ...................................................................................
5.3.3 Resetting the OVP circuit .....................................................................................................
5.4 UNDER VOLTAGE LIMIT (UVL) ..................................................................................................
5.4.1 Setting the UVL level ...........................................................................................................
5.5 FOLDBACK PROTECTION ..........................................................................................................
5.5.1 Setting the Foldback protection ...........................................................................................
5.5.2. Resetting activated Foldback protection ............................................................................
5.6 OUTPUT ON/OFF CONTROL ......................................................................................................
5.7 OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR ..............................
5.8 ENABLE/DISABLE CONTROL VIA REAR PANEL J1 CONNECTOR ..........................................
5.9 CV/CC SIGNAL .............................................................................................................................
5.10 PS_OK SIGNAL ..........................................................................................................................
5.11 SAFE START AND AUTO-RESTART MODES ............................................................................
5.11.1 Automatic start mode .........................................................................................................
5.11.2 Safe start mode ..................................................................................................................
5.12 OVER TEMPERATURE PROTECTION (OTP) ..........................................................................
5.13 LAST SETTING MEMORY .........................................................................................................
5.14 SERIES OPERATION .................................................................................................................
5.14.1 Series connection for increased output voltage .................................................................
5.14.2 Series connection for positive and negative output voltage ...............................................
5.15 PARALLEL OPERATION ............................................................................................................
5.16 DAISY-CHAIN CONNECTION ....................................................................................................
5.17 FRONT PANEL LOCKING ..........................................................................................................
.............................................................................................
Pg.34
Pg.34
Pg.34
Pg.34
Pg.34
Pg.35
Pg.35
Pg.35
Pg.35
Pg.35
Pg.36
Pg.36
Pg.36
Pg.36
Pg.36
Pg.36
Pg.36
Pg.37
Pg.37
Pg.37
Pg.38
Pg.38
Pg.38
Pg.38
Pg.38
Pg.38
Pg.39
Pg.40
Pg.41
Pg.43
Pg.43
Page 8
TABLE OF CONTENTS
Pg.68
8.5
CHAPTER 6 REMOTE ANALOG PROGRAMMING
6.1INTRODUCTION ...........................................................................................................................
6.2 LOCAL/REMOTE ANALOG CONTROLL.......................................................................................
6.3 LOCAL/REMOTE ANALOG INDICATION......................................................................................
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT .............
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT ...........................
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT .............................................
CHAPTER7RS232 & RS485 REMOTE CONTROL
7.1INTRODUCTION ...........................................................................................................................
7.2 CONFIGURATION .........................................................................................................................
7.2.1 Default setting .......................................................................................................................
7.2.2 Address setting .....................................................................................................................
7.2.3 RS232 or RS485 selection ...................................................................................................
7.2.4 Baud rate setting ...................................................................................................................
7.2.5 Settingthe unitinto Remoteor Local mode ..........................................................................
7.2.6 RS232/458 portat Local mode .............................................................................................
7.2.7Front panel in Remote mode ................................................................................................
7.3 REAR PANEL RS232/485 CONNECTOR ......................................................................................
7.4 CONNECTING POWER SUPPLIES TO RS232 OR RS485 BUS .................................................
7.4.1Single power supply ..............................................................................................................
7.4.2 Multi power supplies connectionto RS232 or RS485 bus ....................................................
7.5 COMMUNICATION INTERFACE PROTOCOL ..............................................................................
7.5.1 Dataformat ...........................................................................................................................
7.5.2 Addressing ............................................................................................................................
7.5.3 End of message ....................................................................................................................
7.5.4 Command repeat .................................................................................................................
7.5.5 Checksum .............................................................................................................................
7.5.6 Acknowledge .........................................................................................................................
7.5.7Error message ......................................................................................................................
7.5.8 Backspace ............................................................................................................................
7.6 ERROR MESSAGES .....................................................................................................................
7.7 COMMAND SET DESCRIPTION ..................................................................................................
7.7.1 General guides .....................................................................................................................
7.7.2 Command set categories ......................................................................................................
7.7.3Initialization control commands .............................................................................................
7.7.4ID control commands ............................................................................................................
7.7.5 Output control commands .....................................................................................................
7.7.6Global output commands.......................................................................................................
7.7.7Status control commands .....................................................................................................
7.8STATUS, ERROR AND SRQ REGISTERS ...................................................................................
7.8.1 General .................................................................................................................................
7.8.2 Conditional registers .............................................................................................................
7.8.3 Service Request: Enabled and Event Registers ...................................................................
7.9 SERIAL COMMUNICATION TEST SET-UP ..................................................................................
CHAPTER8ISOLATED ANALOG PROGRAMMING OPTION
8.1INTRODUCTION ...........................................................................................................................
8.2 SPECIFICATIONS .........................................................................................................................
8.2.10-5V/0-10V option .................................................................................................................
8.2.24-20mA option .......................................................................................................................
8.3ISOLATED PROGRAMMING&MONITORING CONNECTOR ....................................................
8.4 SETUP AND OPERATING INSTRUCTIONS .................................................................................
8.4.1 Settingupthe power supplyfor 0-5/0-10V Isolated Programming and Monitoring ...............
8.4.2 Settingupthe power supplyfor 4-20mA Isolated Programming and Monitoring ..................
PARALLEL OPERATION WITH ISOLATED ANALOG OPTION................................................................Pg.
.................................................................
...............................................................
..............................................
Pg.44
Pg.44
Pg.44
Pg.44
Pg.45
Pg.46
Pg.47
Pg.48
Pg.48
Pg.48
Pg.48
Pg.48
Pg.48
Pg.48
Pg.48
Pg.49
Pg.49
Pg.49
Pg.50
Pg.50
Pg.51
Pg.51
Pg.51
Pg.51
Pg.51
Pg.51
Pg.51
Pg.51
Pg.52
Pg.52
Pg.52
Pg.52
Pg.52
Pg.52
Pg.53
Pg.53
Pg.53
Pg.55
Pg.56
Pg.57
Pg.57
Pg.57
Pg.58
Pg.61
Pg.62
Pg.62
Pg.62
Pg.62
Pg.62
Pg.63
Pg.64
Pg.64
Pg.64
65
CHAPTER 9 MAINTENANCE
9.1INTRODUCTION ...........................................................................................................................
9.2 UNITS UNDER WARRANTY .........................................................................................................
9.3 PERIODIC MAINTENANCE ..........................................................................................................
9.4 ADJUSTMENT AND CALIBRATION .............................................................................................
9.5PARTS REPLACEMENT AND REPAIRS .......................................................................................
9.6 TROUBLESHOOTING ...................................................................................................................
9.7 FUSE RATING ...............................................................................................................................
USER MANUAL INDEX ........................................................................................................................
......................................................................................................
Pg.66
Pg.66
Pg.66
Pg.66
Pg.66
Pg.66
Pg.66
Pg.67
Page 9
This page intentionally left blank
Page 10
WARRANTY
This TDK-Lambda Ltd. product is warranted against defects in materials and workmanship for a period of
ve years from date of shipment. During the warranty period, TDK-Lambda Ltd. will, at it's option, either
repair or replace products which prove to be defective.
LIMITATION OF WARRANTY
The warranty shall not apply to defects resulting from improper or inadequate usage or maintenance
by the buyer, buyer supplied products or interfacing. The warranty shall not apply to defects resulting
from unauthorized modications or from operation exceeding the environmental specications of the
product or if the QA seal has been removed or altered by anyone other than TDK-Lambda Ltd. authorized
personnel. TDK-Lambda Ltd. does not warrant the buyers circuitry or malfunctions of TDK-Lambda
Ltd. products resulting from the buyer's circuitry. Furthermore, TDK-Lambda Ltd. does not warrant any
damage occurring as a result ofthe buyer's circuitry or the buyer's - supplied products. No other warranty
is expressed or implied.
WARRANTY SERVICE
This product must be returned to an authorized TDK-Lambda Ltd. service facility for repairs or other
warranty service. For products returned to TDK-Lambda Ltd. for warranty service, the buyer shall prepay
shipping charges to TDK-Lambda Ltd. and TDK-Lambda Ltd. shall pay the shipping charges to return the
product to the buyer. Refer to section 3.11 for repackaging for shipment.
DISCLAIMER
The information contained in this document is subject to change without notice. TDK-Lambda Ltd. shall not
be liable for errors contained in this document or for incidental or consequential damages in connection
with the furnishing, performance or use of this material. No part of this document may be photocopied,
reproduced or translated into another language without the prior written consent of TDK-Lambda Ltd..
TRADEMARK INFORMATION
Genesys™ power supply is a trademark of TDK-Lambda Ltd. & TDK- Lambda Americas Inc.
Microsoft™ and Windows™ are trademarks of Microsoft Corporation.
1
Page 11
REGULATORY NOTICES
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
WARNING: Modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment under FCC Rules.
CE Notice (European Union)
Marking by the CE Symbol indicates compliance to the EMC Directive and the Low Voltage
Directive of the European Union. Such marking is indicative that the Genesys series GEN3300W
meets the following technical standards:
TM
A “Declaration of Conformity” in accordance with the preceding directives and standards has been
made and is on file at our EU representative TDK-Lambda Limited, located at Kingsley Avenue,
Ilfracombe, Devon EX34 8ES, UK.
EN 55022:2010 Information technology equipment - Radio disturbance characteristics Limits and methods of measurement.
EN 55024:2010 Information thecnology equipment - Immunity characteristics - Limits and
methods of measurement.
EN 60950-1:2006+A11:2009 + A1:2010 + A12:2011 Information technology equipment Safety - Part 1: General requirements.
WARNING: This is a Class A product. On a domestic environment this product may cause radio
interference in which case user may be required to takeadequate measures.
SAFETY APPROVALS:
UL 60950-1 Second Edition, UL Listed, C-UL for Canada, IEC 60950-1 Second Edition, CE
marking, when applied to the GEN3300W product, indicates compliance with the Low Voltage
Directive 2006/95/EC in that it complies with EN 60950-1 Second Edition.
2
Page 12
SAFETY INSTRUCTIONS.
ENVIRONMENTAL CONDITIONS
The Genesys power supply series safety approval applies to the following operating conditions:
*Indoor use *Ambient temperature: 0Cto 50 C
*Maximum relative humidity: 90% (no condensation) *Altitude: up to 3000m
*Pollution degree 2
CAUTION
!
TM
oo
Do not use this product in environmentswith strong Electromagnetic field, corrosive
gas and conductive materials.
CAUTIONRiskof Electrical Shock.
Instruction manual symbol. The
instrument will be marked with this
symbol when it is necessary for the
user to referto the instruction
manual.
Indicates hazardous voltage.
-
-
On (Supply)
Direct Current (DC)
-
Alternative Current (AC)
~
Indicates ground terminal.
3
~
Three-PhaseAlternating Current
Protective Ground Conductor Terminal
Off (Supply)
WARNING
CAUTION
Standby (Supply)
The WARNING sign denotes a hazard. An attention toaprocedure is called.
Not following procedure correctly could result in personal injury.
AWARNING sign should not be skipped and all indicated conditions must be
fully understood and met.
The CAUTION sign denotes a hazard. An attention toaprocedure is called. Not
following procedure correctly could result in damage to the equipment. Do not proceed
beyond aCAUTION sign until all indicated conditions are fully understood and met.
FCC COMPLIANCE NOTICE:
Note: This equipment has been tested and found to comply with the limits for aClass A
digital device, pursuant to part 15 of the FCCRules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated inacommercial environment. This equipment generates uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment inaresidential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
345
Page 13
Page 14
Page 15
CHAPTER 1 GENERAL INFORMATION
1.1 USER MANUAL CONTENT
This user’s manual contains the operating instructions, installation instructions and specifications of
the Genesys 3300W power supply series. The instructions refer to the standard power supplies,
including the built-in RS232/485 serial communication. For information related to operation with the
optional IEEE programming, refer to User Manual for Power Supply IEEE Programming Interface.
1.2 INTRODUCTION
TM
1.2.1 General description
Genesys power supplies are wide output range, high performance switching power supplies. The
Genesys series is power factor corrected and operates from worldwide AC voltage range. Output
TM
TM
voltage and current are continuously displayed and LED indicators show the complete operating
status of the power supply. The Front panel controls allow the user to set the output parameters, the
protection levels (Over-Voltage protection, Under-Voltage limit and Foldback) and preview the
settings. The rear panel includes the necessary connectors to control and monitor the power supply
operation by remote analog signals or by the built-in serial communication (RS232/485). GPIB
programming and Isolated-Analog programming/monitoring are optional.
1.2.2 Models covered by this manual
Model Voltage Current
range(V) range(A)
GEN8-400 0-8 0-400
GEN10-330 0-10 0-330
GEN15-220 0-15 0-220
GEN20-165 0-20 0-165
GEN30-110 0-30 0-110
GEN40-85 0-40 0-85
GEN60-55 0-60 0-55
GEN80-42 0-80 0-42
GEN100-33 0-100 0-33
GEN150-22 0-150 0-22
GEN200-16.5 0-200 0-16.5
GEN300-11 0-300 0-11
GEN600-5.5 0-600 0-5.5
Table1-1: Models covered by the manual
1.2.3 Features and options
Constant Voltage /Constant Current with automatic crossover.
*
* Active Power Factor correction.
* Single Phase or Three Phase options.
*Embedded Microprocessor Controller.
* Built in RS232/485 Interface.
*Voltage&Current high resolution adjustment by digital encoders.
*High accuracy programming/readback-16 bit.
* Software Calibration (no internal trimmers / potentiometers).
* Last Setting Memory.
* Independent Remote ON/OFF (opto-isolated) and Remote Enable/Disable.
6
Page 16
* Parallel operation (Master/Slave) with Active current sharing.
* Remote sensing to compensate for voltage drop of power leads.
* External Analog Programming and Monitoring standard (0-5V or 0-10V, user selectable).
* Cooling fan speed control for low noise and extended fan life.
* Zero stacking- no ventillation holes at the top and bottom surface of the power supply.
*Optional GPIB interface (SCPI compatible).
*Optional Isolated Analog programming/monitoring (0-5V or 0-10V, user selectable
and 4-20mA).
1.2.4 Multiple output power system
The Genesys power supplies series can be configured intoaprogrammable power
TM
system of up to 31 units using the built-in RS232/RS485 communication port in the power
supply and the RS485 linking cable provided with each power supply.
InaGPIB system, each power supply can be controlled using the optional GPIB controller
(factory installed).
1.2.5 Control via the serial communication port
The following parameters can be programmed via the serial communication port:
1. Output voltage setting.
2. Output current setting.
3. Output voltage measurement.
4. Output on/off control.
5. Output current measurement.
6. Foldback protection setting.
7. Over-voltage protection setting and readback.
8. Under-Voltage limit setting and readback.
9. Power-supply start up mode (last setting or safe mode)
1.2.6 Analog voltage programming and monitoring
Analog inputs and outputs are provided at the rear panel for analog control of the power
supply. The output voltage and the current limit can be programmedby analog voltage or by
resistor, and can be monitored by analog voltage. The power supply output can be remotely
set to On or Off and analog signals monitor the proper operation of the power supply and the
mode of operation (CV/CC).
1.2.7 Parallel operation
Genesys power supplies of the same output voltage and current rating can be paralleled in
TM
master-slave configuration with automatic current sharing to increase power available.
1.2.8 Output connections
Output connections are made to rear panel bus-bars for models up to 100V and toa4terminal wire clamp connector for models above 100V rated output voltage. Either the
positive or negative terminal maybe grounded or the output maybe floated. Models up to
60VDC Rated Output shall not float outputsmore than +/- 60VDC above/below chassis
ground. Models >60VDC Rated Output shall not float outputsmore than +/-600VDC
above/below chassis ground. Contact factory for assistance with higher float voltage
applications.
Local or remote sense maybe used.
In remote sense, the voltage drop on the load wires
should be minimized. Refer to the specifications for the maximum voltage drop value.
7
Page 17
1.2.9 Cooling and mechanical construction
The Genesys series is cooled by internal fans. At the installation, care must be taken to
allow free air flow into the power supply via the front panel and out of the power supply via
the rear panel. The Genesys power supplies have a compact and lightweight package
TM
TM
which allows easy installation and space saving in the application equipment.
CAUTION
Observe all torque guidelines within this manual. Over torqueing may damage
unit or accessories. Such damage is not covered under manufacturers warranty.
1.3 ACCESSORIES
1.3.1 General
Accessories are delivered with the power supply or separately upon ordering. The list below
shows the possible accessories and ordering numbers.
1.3.2 Serial link cable
S
erial link cable, for linking power supplies by RS485 communication is provided with the
power supply.
Cable description: 0.5m length, shielded, RJ-45 type plugs, 8 contacts (P/N: GEN/RJ45).
1.3.3 Misc. hardware
* DB25 plug kit (AMP, 749809-9).
*Strain relief for AC cord
* Output terminal shield
* Plastic legs for bench mounting.
1.3.4 AC cables
AC cables are not provided with the power supply.
Refer to Table1-2 for recommended AC input cables (customer supplied). Add a non-locking
plug approved by the national safety standards of the country of usage.
AC Input Range
190-240V~ ,Single Phase
3x 12AWG (2 wire plus safety graund), stranded
copper, 300V,60Cminimum, rated for 25A. 3m
AC Input Cable
O
max. length, outer diameter: 9~11mm.
190-240V~ , Three Phase
4x14AWG (3 wire plus safety ground), standed
copper, 300V,60cminimum, rated for 15A. 3m
O
max. length, outer diameter: 9~11mm.
380-415V~ , Three Phase
4x16AWG (3 wire plus safety ground), standed
copper, 600V,60cminimum, rated for 10A. 3m
O
max. length, outer diameter: 9~11mm.
Table 1-2: Recommended AC input cable
8
Page 18
CHAPTER 2 SPECIFICATIONS
1.Vout voltage programming
2.Iout voltage programming (*13)
3.Vout resistor programming
4.Iout resistor programming (*13
5.On/off control
6.Output current monitor (*13)
7.Output voltage monitor
8.Power supply OK signal
9.Parallel operation
10.Series operation
11.CV/CC indicator
12.Enable/Disable
13.Local/Remote analog control
14.Local/Remote analog indicator
)
2.5 ANALOG PROGRAMMING AND MONITORING
---
---
---
---
---
---
---
---
---
---
---
---
---
---
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-1% of rated Iout.
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1% of rated Vout.
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1.5% of rated Iout.
By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
0~5V or 0~10V, user selectable. Accuracy: +/-1%.
0~5V or 0~10V, user selectable. Accuracy : +/-1%.
4~5V-OK, 0V-Fail. 500ohm series resistance.
Possible , up to 4 units in master/slave mode with two wires current balance connection.
Possible (with external diodes), up to 2 units.
Open collector. CC mode: On, CV mode: Off. Maximum voltage: 30V, maximum sink current: 10mA.
Dry contact. Open: Off, Short: On. Max. voltage at Enable/Disable in: 6V.
By electrical signal or Open/Short: 0~0.6V or short: Remote, 2~15V or open: Local.
Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 10mA.
2.1 OUTPUT RATING
1.Rated output voltage(1*)
2.Rated output current (*2)
3.Rated output power
V
A
W
MODEL
GEN
8-400
8
400
3200
10-330
10
330
3300
15-220
15
220
3300
20-165
20
165
3300
30-110
30
110
3300
40-85
40
85
3400
60-55
60
55
3300
80-42
80
42
3360
100-33
100
33
3300
150-22
150
22
3300
200-16.5
200
16.5
3300
300-11
300
11
3300
600-5.5
600
5.5
3300
2.2 INPUT CHARACTERISTICS
Single Phase models:
3-Phase, 200V models:
3-Phase, 400V models:
---
--%
Single Phase models: 170~265V, 47~63Hz
Single Phase models: 0.99@200Vac, rated output power. 3-Phase models: 0.95@200/380Vac, rated output power.
3-Phase, 200V models: 170~265Vac, 47~63Hz
3-Phase, 400V models: 342~460Vac, 47~63Hz
Single-Phase and 3-Phase 200V models: Less than 50A
3-Phase 400V models: Less than 20A
V
8
10
15
20
30
60
40 150
100
80
600
200
300
24.0
14.5
7.2
24.0
14.5
7.2
24.0
14.5
7.2
24.0
14.5
7.2
23.0
14.0
7.0
24.0
14.5
7.2
23.0
13.6
6.8
23.5
14.0
7.0
23.0
13.7
6.8
23.0
13.7
6.8
23.0
13.7
6.8
23.0
13.9
7.0
23.0
13.8
6.9
3.Power Factor (Typ)
4.Efficiency (*4)
5.Inrush current (*5)
2.Maximum
Input current
at 100% load
1.Input voltage/freg. (*3)
---
A
82
83
83
83
86
86
87
88
88
88
87
87
87
8
10
15
30
20
40
60
80
150
100
200
300
600
2.3 CONSTANT VOLTAGE MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*7)
3.Ripple and noise (p-p , 20MHz) (*8)
4.Ripple r.m.s., 5Hz~1MHz
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
8.Remote sense compensation/wire
9.
11.Transient response time
12.Hold-up time (Typ)
Up-prog. response time, 0~Vomax.(*9)
10.Down-prog. response time
Full load(*9)
No load(*10)
V
---
--mV
mV
---
---
V
mS
PPM/ C
o
mS
mS
mS
0.01% of rated output voltage +2mV
0.015% of rated output voltage +5mV
55
8
55
7
55
8
55
7
55
7
70
20
100
20
350
80
55
7
60
7
100
25
275
70
300
80
50PPM/ C from rated output voltage, following 30 minutes warm-up.
O
0.01% of rated Vout over 8 hrs interval following 30 minutes warm-up. Constant line, load & temp.
Less than 0.05% of rated output voltage +2mV over 30 minutes following power on.
2
2
2
2
5
5
5
5
5
5
5
5
200
5
80
250
20
100
500
600
700
800
160
900
1000
300
150
1100
1200
1500
2000
500
3000
3500
4000
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated output
current. Output set-point: 10~100%, Local sense.
Less than 1mS, for models up to and including 100V. 2mS, for models above 100V.
10mSec for Single-Phase and 3-Phase 200V models, 6mSec for 3-Phase 400V models. Rated output power.
V
8
10
15
20
40
30
60
80
100
150
200
600
300
2.4 CONSTANT CURRENT MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*11)
3.Load regulation thermal drift
4.Ripple r.m.s. 5Hz~1MHz (*12)
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
---
---
---
---
---
mA
PPM/ C
o
0.01% of rated output current +2mA
0.02% of rated output current +5mA
70PPM/ C from rated output current, following 30 minutes warm-up.
0.01% of rated Iout over 8hrs interval following 30 minutes warm-up. Constant line, load & temperature.
O
Less than 0.1% of rated output current over 30 minutes following load change.
650
400
300
1000
150
250
20
50
70
60
30
15
8
8~20V model: Less than +/-0.5% of rated output current over 30 minutes following power on.
30V~600V model: Less than +/-0.25% of rated output current over 30 minutes following power on.
9
Page 19
2.6 PROGRAMMING AND READBACK (RS232/485, Optional LAN/IEEE Interface)
1.Vout programming accuracy (*14)
2.Iout programming accuracy (*13)
3.Vout programming resolution
4.Iout programming resolution
5.Vout readback accuracy
6.Iout readback accuracy (*13)
7.Vout readback resolution
8.Iout readback resolution
---
---
---
---
---
---
0.05% of rated output voltage
0.1% of actual output current +0.2% of rated output current
0.002% of rated output voltage
0.002% of rated output current
0.05% of rated output voltage
0.3% of rated output current
2.7 PROTECTIVE FUNCTIONS
1.Foldback protection
2.Over-voltage protection
3.Over-voltage trip point
4.Output under voltage limit
5.Over temperature protection
---
---
---
---
V
Output shut-down when power supply change from CV to CC User presetable.
Inverter shut-down, manual reset by AC input recycle or by OUT button or by communication port command.
Preset by front panel or communication port. Prevents from adjusting Vout below limit. Does not affect analog
programming.
User selectable, latched or non latched.
0.5~10
0.5~12
2~36
1~24
1~18
2~44
5~66
5~165
5~110
5~88
5~220
5~330
5~660
V
8
15
2010
30
40
60
80
100
150
200
300
600
V
8
15
2010
30
40
60
80
100
150
200
300
600
2.8 FRONT PANEL
---
---
---
---
---
---
---
---
---
---
---
---
---
Vout/Iout manual adjust by separate encoders (coarse and fine adjustment).
OVP/UVL manual adjust by Vout. Adjust encoder.
Address selection by Voltage Adjust encoder. No of addresses:31.
Go to local control.
Output on/off
AC on/off
Front panel Lock
Foldback control
Baud rate selection: 1200, 2400, 4800, 9600 and 19200.
Re-start modes (automatic restart, safe mode).
Vout: 4 digits, accuracy: 0.05% of rated output voltage +/-1count.
Iout: 4 digits, accuracy: 0.2% of rated output current +/-1count.
VOLTAGE, CURRENT, ALARM, FINE, PREVIEW, FOLDBACK, LOCAL, OUTPUT ON, FRONT PANEL LOCK.
1.Control functions
2.Display
3.Indications
2.9 ENVIRONMENTAL CONDITIONS
1.Operating temperature
2.Storage temperature
3.Operating humidity
4.Storage humidity
5.Altitude
---
--%
%
---
0~50 C, 100% load.
-20~85 C
20~90% RH (no condensation).
10~95% RH (no condensation).
Maximum 3000m. Derate output current by 2%/100m above 2000m. Alternatively, derate maximum
ambient temperature by 1 C/100m above 2000m.
o
o
O
2.10 MECHANICAL
1.Cooling
2.Weight
3.Dimensions (WxHxD)
4.Vibration
5.Shock
---
Kg
mm
---
---
Forced air cooling by internal fans.
Less than 13Kg.
W: 423, H: 88, D: 442.5 (Refer to Outline drawing).
MIL-810F, method 514.5
Less than 20G, half sine, 11mS. Unit is unpacked.
Models with Vout 50V: Output is SELV, all communication/control interfaces (RS232/485, IEEE, Isolated Analog,
LAN, Sense, Remote Programming and Monitoring) are SELV.
Models with 60V Vout 400V: Output is Hazardous, communication/control interfaces: RS232/485, IEEE,
Isolated Analog, LAN, Remote Programing and Monitoring (pins 1-3, pins14-16) are SELV, Sense, Remote
Programming and Monitoring (pins 8-13, pins 21-25) are Hazardous.
Models with 400V<Vout 600V: Output is Hazardous, all communication/control interfaces (RS232/485, IEEE,
Isolated Analog, LAN, Sense, Remote Programming and Monitoring) are Hazardous.
Vout 50V models : Input-Output (SELV): 4242VDC 1min, Input-communication/control (SELV): 4242VDC 1min,
Input-Ground: 2828VDC 1min,
60V<Vout 100V models: Input-Output (Hazardous): 2600VDC 1min, Input-communication/control (SELV):
4242VDC 1min, Output(Hazardous)-SELV: 1900VDC 1min, Output(Hazardous)-Ground: 1200VDC 1min,
Input-Ground: 2828VDC 1min.
100V< Vout 600V models: Input-Output(Hazardous): 3550VDC 1min, Input-communication/control (SELV):
4242VDC 1min, Hazardous. Output-communication/control(SELV): 4242VDC 1min,
Output(Hazardous)-Ground: 2670VDC 1min, Input-Ground: 2828VDC 1min.
More than 100Mohm at 25 C, 70%RH.
O
2.11 SAFETY/EMC
2.Interface classification
4.Insulation resistance
3.Withstand voltage
1.Applicable standards: Safety
---
---
---
---
---
EMC
UL 60950-1, CSA22.2 No.60950-1, IEC 60950-1, EN 60950-1
EN55022, EN55024, EN61000-3-3, FCC part 15, VCCI.
Conducted emmision - EN55022 class A, FCC part 15 class A, VCCI class A.
Radiated emmision - EN55022 class A, FCC part 15 class A, VCCI class A.
Immunity - EN55024
% of rated
output voltage
% of rated
output current
0.002%
0.003%
0.007%
0.006%0.011%
0.004%
0.003%
0.002%
0.002%
0.011%
0.007%
0.006%
0.004%
0.002%
0.005%
0.007%0.004%
0.01%
0.002%
0.002%
0.003%
0.004%
0.005%
0.007%
0.01%
0.002%
10
Page 20
NOTES:
*1: Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage.
*2: Minimum current is guaranteed to maximum 0.4% of the rated output current.
*3: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be
described as 190~240Vac (50/60Hz) for Single-Phase and 3-Phase 200V models, and
380~415Vac (50/60Hz) for 3-Phase 400V models.
*4: Single-Phase and 3-Phase 200V models: at 200Vac input voltage.
3-Phase 400V: at 380Vac input voltage. With rated output power.
*5: Not including EMI filter inrush current, less than 0.2mSec.
*6: Single-Phase and 3-Phase 200V models: 170~265Vac, constant load.
3-Phase 400V models: 342~460Vac, constant load.
*7: From No-load to Full-load, constant input voltage. Measured at the sensing point in Remote
Sense.
*8: For 8V~300V models: measured with JEITA RC-9131A (1:1) probe.
For 600V model: measured with 10:1probe.
*9: From10% to 90% or 90% to 10% of rated output voltage, with rated , resistive load.
*10: From 90% to 10% of rated output voltage.
*11: For load voltage change, equal to the unit voltage rating, constant input voltage.
*12: For 8V~15V models the ripple is measured at 2V rated output voltage and rated output
current. For other models, the ripple is measured at 10~100% of rated output voltage and
rated output current.
*13: The Constant Current programming readback and monitoring accuracy does not include the
warm-up and Load regulation thermal drift.
*14: Measured at the sensing point.
2.12 SUPPLEMENTAL CHARACTERISTICS
The supplemental characteristics give typical but non-warranted performance characteristics.
The supplemental characteristics are useful in assessing applications for the power supply.
Several kinds of supplemental characteristics are listed below.
1.Evaluation Data: Typical performance of the power supply.
2.Reliability Data: Reliability performance of the power supply.
3.EN61000 Data: Performance of the power supply under EN61000 test conditions.
4.EMI Data: Typical EMI (conducted and radiated) performance of the power supply.
The supplemental characteristics data is held in each Lambda sales and service facility. For further
details please contact the Lambda office nearest you.
11
Page 21
2.13 GENESYS 3300W POWER SUPPLIES
OUTLINE DRAWINGS
TM
NOTES:
1.Analog programming connector. Matingplug suppliedwith
power supply.
2.Bus-barsfor 8V to 100V models. See detail.
Wire clamp connector for 150V to 600V models(shown).
3. AC cablestrain relief(suppliedwith power supply).
4. AC input connector (single phase shown).
5. Chassisslides, GENERAL DEVICES P/N: CC3001-00-S160
or equivalent, mounting holes #10-32 marked "A".
6. Bus Bars enclosurefor 60V to 600V.
7. Mounting holes for 19” rack. Use M6x16
screws to fix the unittothe rack.
423.0±1.0mm
Note1
Note2(150V~600V)
Note4
Note7
88.0mm±0.3
50.0
19.0
482.0±1.0mm
Bus-Bar Detail
8V to 100V Models
40.0m
m
30.0mm
5.0mm
50.0mm
10.5mm
60.5
92.0
92.0
442.5±1.0mm
642.5±1.0mm
517.0±1.0mm
35.5±1.0mm
Note5
Note3
Note2
Note6
42.0
A
A
A
86±0.3
T
D
L
amb
da
-
I
10
4
±
2.0m
m
76.2
12
Page 22
CHAPTER 3 INSTALLATION
3.1 GENERAL
This chapter contains instructions for initial inspection, preparation for use and repackaging for
shipment. Connection to PC, setting the communication port and linking Genesys power supplies
are described in Chapter 7.
WARNING
The Genesys series is intended only for installation in
Restricted Access Location (RAL). Access to Hazardous
parts (rear side of the power supply) shall be prevented after
installation.
Genesys power supplies generate magnetic fields which
might affect the operation of other instruments. If your
equipment is susceptible to magnetic fields, do not position
it adjacent to the power supply
TM
TM
NOTE
WARNING
TM
.
through the front panel slits.
3.2 PREPARATIONFOR USE
To avoid electric shock hazard, do not insert conductive parts
I
n order to be operational the power supply must be connected to an appropriate AC source. The
AC source voltage should be within the power supply specification. Do not apply power before
reading, Section 3.6 and 3.7.
Table 3-1 below, describes the basic setup procedure. Follow the instructions in Table 3-1 in the
sequence given to prepare the power supply for use.
Step no.
1
2
3
4
5
6
Item Description Reference
Inspection
Installation
AC source
Test
Load connection
Default setting
Initial physical inspection of the power supply
Installing the power supply,
Ensuring adequate ventillation.
AC source requirements
Connecting the power supply to the AC source.
Turn-on checkout procedure.
Wire size selection. Local /Remote sensing.
Single or multiple loads.
The power supply setting at shipment.
Section 3.3
Section 3.4
Section 3.5
Section 3.6
Section 3.7
Section 3.8
Section 3.9
Section 7.2.1
Table 3-1: Basic setup procedure
3.3 INITIALINSPECTION
Prior to shipment this power supply was inspected and found free of mechanical or electrical
defects. Upon unpacking of the power supply, inspect for any damage which may have occured in
transit.
The inspection should confirm that there is no exterior damage to the power supply such as broken
knobs or connectors and that the front panel and meters face are not scratched or cracked. Keep all
packing material until the inspection has been completed. If damage is detected, fileaclaim with
carrier immediately and notify the Lambda sales or service facility nearest you.
3.4 RACK MOUNTING
The Genesys power supply series is designed to fit inastandard 19” equipment rack.
TM
3.4.1 To install the Power Supply inarack:
1. Use the front panel rack-mount bracketsto install the power supply in the rack.
2. Useasupport bar to provide adequate support for the rear of the power supply.Do not obstruct
the air exhaust at the rear panel of the unit.
13
Page 23
14
Page 24
r
WARNING
so
The
n
the
Some componentsinsidethe power supplyare at AC voltage even whenthe On/Offswitch is in the
“Off”position.Toavoid electric shock hazard, disconnect the line cord and load and waittwo
minutes beforeremovingcover.
CAUTION
AC Input WiresNo Conductor Pretreatment:PhoenixContact clamping parts are designed
that all kinds of copper conductors canbe clamped without pretreatment.
It is forbidden to solder theconductors. The solder tin yieldsand fractures under high pressure.
result is increased contact resistance and an excessive temperature rise.Inaddition, corrosio
caused by picklingor fluxeshas been observedonsoldered conductor ends. Notch fractures at
transition point fromthe rigid to the flexible conductorareaare also possible.
The power supply ON/OFF switch is not themain “disconnectdevice”and does not completely
disconnectall the circuits fromthe AC source.
An appropriately rated“disconnect device”suchas circuit breaker, typeBplugonpower cord, ...etc.,
shallbeprovided in the final installation. The “disconnectdevice” for onephaseunits shall
disconnect bothsupply lines simultaneously.The “disconnected device”must be easily accessible.
3.7.1ACInput Connector
TheAC input connector is:for single phase: Phoenix ContactP/N: PC6/3-STF-10,16
forthree phase: Phoenix ContactP/N: PC6/4-STF-10,16
Header :for single-phase: Phoenix Contact P/N: PC6-16/3-GF-10,16
forthree-phase: Phoenix Contact P/N: PC6-16/4-GF-10,16
Use suitablewires and tightening torque as follows:
1. Wire diameter: 12AWG forsingle-phase models,
14AWG forthree-phase 200V models and
16AWG forthree-phase 400V models. Refer to Table1-2 for details.
2. Tightening torque: 10.7-13.4Lb-inch. (1.2 -1.5Nm).
3.7.2ACInput Cord
WARNING
AC input cordis not provided with power supply.
Refer to section1.3.4 for details of therecommended AC input cords and to section3.7 fo
disconnected device requirement.
3.7.3ACInput Wire Connection
1.Stripthe outside insulationofthe AC cable approx. 10cm. Trim thewiressothat theground wire is
10mm longer than theother wires. Strip 10mm at the end of each of thewires.
2.Unscrew the base of thestrain relief fromthe helix-shaped body.Insertthe base through the
outside opening in theACinput cover and screw thelocknut securely(11-14 Lb-inch.)intothe
base, fromthe inside.
3.Slidethe helix-shaped body ontothe AC cable. Insertthe stripped wiresthrough thestrain relief
Screw-on
Locknut
Fig.3-2: Stripped WiresinstalledinStrain Relief
15
Page 25
4.Connect
5.
position
Fig.3-4: AC input cover and strain relief
Removable cover. Remove only
to inspect AC Input wires
connection. Reinstall cover after
inspection.
Assembled Strain Relief
M3x8
Flat Head screws
(2 places)
L1
L2
L3
the AC wires to the terminals of the input plug supplied with the unit. To connect the
wires, loosen the terminal screw, insert the stripped wire into the terminal and tighten the
screw securely (4.4-5.3 Lb-inch.). Refer to Fig. 3-3 for details. Pay attention to connect the
wires according to the polarity marking on the plug.
AC Input Plug :
Single Phase: P/N: PC6/3-STF-10,16
Wire clamp screws
tightening torque: 10.7- 13.4 Lb-inch.
3-Phase: P/N: PC6/4-STF-10,16:
Protective Ground wire
t
AC Line wires
Fig.3-3: AC Input plug (3-Phase shown)
Connect the AC input plug to the AC input connector at the power supply rear panel. Fasten
the plug to the connector using the two screwsat each side of the plug.
(Tightening torque:10.7-13.4Lb inch)
Route the wires inside the cover to prevent pinching. Fasten the cover to the unit using the
M3x8 Flat Head screws are provided. Refer to Fig.3-4 for details.
3.8 TURN-ON CHECKOUT PROCEDURE
3.8.1 General
The following procedure ensures that the power supply is operational and may be used asabasic
incoming inspection check. Refer to Fig.4-1 and Fig.4-2 for the location of the controls indicated in
the procedure.
3.8.2 Prior to Operation
1. Ensure that the power supply is configured to the default setting:
-AC On/Off switch at Off position.
-Dip switch : All positions at Down (”Off”) position.
-Sense connector : Configured to Local Sense as shown in Fig.3-5:
1 Remote (+) sense
2 Local (+) sense
3 Not connected
4 Local (-) sense
5 Remote (-) sense
Fig.3-5: Sense connector default connection
Plug P/N: MC 1.5/5-ST-3.81
(Phoenix)
-For units equipped with IEEE option, ensure that the IEEE_En switch is in Up (default)
(Refer to Fig.4-2, item8for location), if checkout is to be done in IEEE mode.
16
Page 26
2. Connect the unit to anAC source as described in section 3.7.
3. Connect aDVM with appropriate cables for the rated voltage to the output terminals.
4. Turn the front panel AC power switch to On.
3.8.3 Constant Voltage Check
1. Turn on the output by pressing OUT pushbutton so the OUT LED illuminates.
2. Observe the power supply VOLT display and rotatethe Voltage encoder. Ensure that the
output voltage varies while the VOLT encoder is rotated. The minimum control range is from
zero to the maximum rated output for the power supply model.
Compare the DVM reading with the front panel VOLT display to verify the accuracy of the
VOLT display. Ensure that the front panel VOLT LED is on.
3. Turn off the front panelAC power switch.
3.8.4 Constant Current Check
1. Ensure that the front panelAC power switch is at Off position and the DVM connected to the
output terminals shows zero voltage.
2. Connect aDC shunt across the output terminals. Ensure that the shunt and the wires' current
ratings are higher than the power supply rating. Connect a DVM to the shunt.
3. Turn the front panel AC power switch to On position.
4. Turn on the output by pressing OUT pushbutton so the OUT LED illuminates.
5. Observe the power supply CURRENTdisplay and rotate the CURRENT encoder. Ensure that
the output current varies while the CURRENT encoder is rotated. The minimum control range
is from zero to the maximum rated output for the power supply model.
Compare the DVM reading with the front panel CURRENT display to verify the accuracy of
the CURRENT display. Ensure that the front panel CURRENT LED is on.
6. Turn off the front panel AC power switch.
7. Remove the shunt from the power supply output terminals.
3.8.5 OVPCheck
Refer to Section 5.3 for explanation of the OVP function prior to performing the procedure below.
1. Turn the front panel AC power switch to On position and turn on the output by pressing OUT
pushbutton.
2. Using the VOLT encoder, adjust the output voltage to approx. 10% of the unit voltagerating.
3. Momentarily press
VOLTAGE display will show the last setting of the OVPlevel.
4. Rotate the VOLT encoder CCW to adjust the OVPsetting to 50% of the unit voltage rating.
5. Wait a few seconds until the VOLT display returns to show the output voltage.
6. Adjust the output voltagetoward it’smaximum and check that the output voltagecannot be
increased more than the OVP setting.
7. Adjust OVPlimit to the maximum by repeating step 3 and rotatingthe VOLT encoder CW.
3.8.6 UVLCheck
Refer to Section 5.4 for explanation of the UVLfunction prior to performing the procedure below.
1. Press the OVP/UVLbutton TWICEso that the CURRENT display shows"UUL". The VOLTAGE
display will show the last setting of the UVL level.
2. Rotate the VOLT encoder to adjust the UVL level to approx. 10% of the unit voltage rating.
3. Wait a few seconds until the VOLT display returns to show the output voltage.
4. Adjust the output voltagetoward it’sminimum and check that the output voltagecannot be
decreased below the UVL setting.
5. Adjust the UVL limit to the minimum by repeating step1 and rotating the VOLT encoder CCW.
the OVP/UVL button so that the CURRENT display shows“OUP”. The
17
Page 27
3.8.7 Foldback Check
WARNING
Shorting the output may expose the user to hazardous
voltages. Observe proper safety procedures.
Refer to Section 5.5 for explanation of the FOLD function prior to performing the procedure
below.
1. Ensure that the output voltage is set to approx. 10% of the unit rating.
2. Adjust the CURRENT encoder to set the current limit to approx. 10% of the unit rating.
3. Momentarily press the FOLD button. Ensure that the FOLD LED illuminates. The output
voltage remains unchanged.
4. Short the output terminals momentarily (approx. 0.5 sec.). Ensure that the output voltage falls
to zero, the VOLT display shows “Fb” and the ALARM LED blinks.
5. Press the FOLD button again to cancel the protection. The output voltage remains zero.
6. Press OUT button. Ensure that the output voltage returns to it’s last setting.
7. Turn the output offby pressing OUT button. Ensure that the VOLT display shows“OFF”.
3.8.8 Address Setting
1. Press and hold the REM/LOC button for approx. 3sec. The VOLT display will show the
communication port address.
2. Using the VOLT adjust encoder, check that the address can be set within the range of0to 30.
3.8.9 Baud Rate Setting
1. Press and hold the REM/LOC button for approx. 3sec. The CURRENT display will show the
communication port Baud Rate.
2. Using The CURRENT adjust encoder, check that the Baud Rate can be set to 1200, 2400,
4800, 9600 and 19200.
3.9 CONNECTINGTHE LOAD
WARNING
Turn off the AC input power before making or changing any
rear panel connection. Ensure that all connections are
securely tightened before applying power.There isapotential
shock hazard when using a power supply with a rated output
greater than 40V.
3.9.1 Load Wiring
The following considerations should be made to select wiring for connecting the load to the power
supply:
* Current carrying capacity of the wire (refer to 3.9.2)
* Insulation rating of the wire should be at least equivalent to the maximum output voltage of
the power supply.
* Maximum wire length and voltage drop (refer to 3.9.2)
* Noise and impedance effectsof the load wiring (refer to 3.9.4).
3.9.2 Current Carrying Capacity
Two factors must be considered when selecting the wire size:
1. Wires should be heavy enough not to overheat while carrying the power supply load
current at the rated load, or the current that would flow in the event the load wires were
shorted, whichever is greater.
at least
18
Page 28
2. Wire size should be selected to enable voltage drop per lead to be less than 1.0V at the rated
current. Although units will compensate for up to 5V in each load wire, it is recommended to
minimize the voltage drop (1V typical maximum) to prevent excessive output power consumption from the power supply and poor dynamic response to load changes. Please refer to
Tables 3-2 and 3-3 for maximum wire length to limit voltage drop inAmerican and European
dimensions respectively.
Wire size
AWG
14
12
10
8
6
4
2
0
Cross sect.
area
2
(mm )
2.5
4
6
10
16
25
35
Resistivity
Ohm/1000ft
2.526
1.589
0.9994
0.6285
0.3953
0.2486
0.1564
0.0983
10A
40
60
100
160
250
400
600
1000
voltage drop to 1V or less
20A
20
30
50
80
125
200
300
500
50A
8
12
20
32
50
80
125
200
100A
4
6
10
15
25
40
60
100
200A
2
3
5
8
12
20
30
50
Table 3-2: Maximum wire length for 1V drop on lead (in feet)
Maximum length in meters to limit
Maximum length in Feet to limit
Resistivity
Ohm/Km
8.21
5.09
3.39
1.95
1.24
0.795
0.565
10A
12.0
18.6
29.4
51.2
80.0
125.0
177.0
voltage drop to 1V or less
20A
6.0
9.8
14.8
25.6
40.0
62.0
88.0
50A
2.4
4.0
5.8
10.2
16.0
25.2
35.4
100A
1.2
2
2.9
5.1
8
12.6
17.7
200A
0.6
1.0
1.45
2.5
4
6.3
8.8
400A
---
--2
4
6
10
15
25
400A
0.3
0.5
0.7
1.25
2
3.1
4.4
Table 3-3: Maximum wire length for 1V drop on lead (in meters)
For currents not shown in Table 3-2 and 3-3, use the formula:
Maximum length=1000/(currentxresistivity)
where current is expressed in Amperes and resistivity in ohms/km or ohms/1000ft.
3.9.3 Wire termination
The wires should be properly terminated with terminals securely attached. DO NOT use unterminated wires for load connection at the power supply.
CAUTION
When local sensing, a short from +LS or +S to -V or -S or -LS,
will cause damage to the power supply.Reversing the sense
wires might cause damage to the power supply in local and
remote sensing. (Do not connect -S to +V or +S to -V.)
19
Page 29
3.9.4 Noise and Impedance Effects
To minimize the noise pickup or radiation, the load wires and remote sense wires should be twistedpairs to the shortest possible length. Shielding of sense leads may be necessary in high noise
environments. Where shielding is used, connect the shield to the chassis viaarear panel Ground
screw. Even if noise is notaconcern, the load and remote sense wires should be twisted-pairs to
reduce coupling, which might impact the stability of power supply. The sense leads should be
separated from the power leads.
Twisting the load wires reduces the parasitic inductance of the cable which could produce high
frequency voltage spikes at the load and the output of power supply, because of current variation in
the load itself.
The impedance introduced between the power supply output and the load could make the ripple
and noise at the load worse than the noise at the power supply rear panel output.Additional filtering
with bypass capacitors at the load terminals may be required to bypass the high frequency load
current.
3.9.5 Inductive loads
Inductive loads can produce voltage spikes that may be harmful to the power supply.Adiode should
be connected across the output. The diode voltage and current rating should be greater than the
power supply maximum output voltage and current rating. Connect the cathode to the positive
output and the anode to the negative output of the power supply.
Where positive load transients such as back EMF fromamotor may occur, connect a surge
suppressor across the output to protect the power supply. The breakdown voltage rating of the
suppressor must be approximately 10% higher than the maximum output voltage of the power
supply.
3.9.6 Making the load connections
WARNING
Hazardous voltages may exist at the outputs and the load connections
when using a power supply with a rated output greater than 40V.To
protect personnel against accidental contact with hazardous voltages,
ensure that the load and its connections have no accessible live parts.
Ensure that the load wiring insulation rating is greater than or equal to
the maximum output voltage of the power supply.
CAUTION
Ensure that the load wiring mounting hardware does not short the output
terminals. Heavy connecting cables must have some form of strain relief
to prevent loosening the connections or bending the bus-bars.
8V to 100V Models
Refer to Fig.3-6 for connection of the load wires to the power supply bus-bars and to Fig.3-7
for mounting the bus-bars shield to the chassis.
20
Page 30
Wire terminal lug (2 places)
Output
so
It
result
caused
transition
M10x25 screw (2 places)
Flat washer
(2 places)
Flat washer (2 places)
Spring washer (2 places)
Hex Nut (2 places)
Screws tightening torque: 290-310 Lb-inch.
Fig. 3-6: Load wires connection, 8V to 100V models.
Fig. 3-7: Bus-bars shield mounting,
8V to 40V models
Fig. 3-8: Bus-bars shield mounting,
60V to 100V models
150V to 600V Models
WARNING
Hazardous voltages exist at the outputs and the load connections. To protect personnel against
accidental contact with hazardous voltages, ensure that the load and its connections have no
accessible live parts. Ensure that the load wiring insulation rating is greater than or equal to the
maximum output voltage of the power supply.
CAUTION
Load Wires No Conductor Pretreatment: Phoenix Contact clamping parts are designed
that all kinds of copper conductors can be clamped without pretreatment.
is forbidden to solder the conductors. The solder tin yields and fractures under high pressure. The
is increased contact resistance and an excessive temperature rise. In addition, corrosion
by pickling or fluxes has been observed on soldered conductor ends. Notch fractures at the
point from the rigid to the flexible conductor area are also possible.
21
Page 31
The
Phoenix
The
output
The
150V to 600V models have afour terminal wire clamp output connector:
Contact P/N: FRONT4-H-7.62/4
twoleftterminalsare the positive outputs and theother two right terminalsare the negative
s.Max. 30A per terminal.
connector requirementsare as follows:
1. Wires: AWG18 to AWG10.
2. Tightening torque: 4.4-5.3Lb-inch. (0.5-0.6Nm).
Followthe below instructions for connectionofthe load wirestothe power supply:
1. Strip approx.10mm at the end of each of theload wires.
2. Loosen the connector terminal screws.
3. Loosen screws “B” from enclosure bottom cover to release the shutter.
4. Insertstripped wiresinto enclosure bottom cover opening and then to theterminals,
tighten theterminals screws securely(see fig.3-9)
5. Assemblethe enclosuretop cover to the chassisas shown in Fig.3-9,using clamp “A1” and
screw “A2”,tighten screw “A2” (tightening torque:4.8-5.3 Lb-inch).
Negative (-)
Output/Return
Enclosuretop cover
A1
A2
Shutters
Positive output (+)
Enclosure bottom cover
B
B
Load wires
Fig.3-9: Load wires connectiontothe output connector
6. Assemble the enclosure bottom cover to it’s place, as showninFig.3-10,using screws“C”,
3 places (tightening torque 4.8-5.3 Lb-inch).
7. Slide down the shutter to secure load wires in place, and tighten screws “B”.
C
B
B
C
Fig.3-10: Enclosure assembly
22
Page 32
3.9.7 Connecting single loads, local sensing (default).
Fig.3-11 shows recommended load and sensing connections forasingle load. The local sense lines
shown are default connections at the rear panel J2 sense connector. Local sensing is suitable for
applications where load regulation is less critical.
+V
Power
Supply
-
Rem.sense
-
Local sense
Local sense
+
+
Rem.sense
3.9.8 Connecting single loads, remote sensing
Fig.3-12 shows recommended remote sensing connection for single loads.
Remote sensing is used when, in Constant Voltage mode, the load regulation is important at the
load terminals. Usetwisted or shielded wires to minimize noise pick-up. If shielded wires are used,
the shield should be connected to the ground at one point, either at the power supply chassis or the
load ground. The optimal point for the shield ground should be determined by experimentation.
Power
Supply
-V
Load lines, twisted
pair, shortest length
possible.
Fig.3-11: Single load connection, local sensing
Load lines. Twisted pair
shortest length possible.
+V
-V
+
Load
-
+
Load
-
-
Rem.sense
-
Local sense
Local sense
+
+
Rem.sense
Fig.3-12: Remote sensing, single load
3.9.9 Connecting multiple loads, radial distribution method
Fig.3-13 showsmultiple loads connected to one supply. Each load should be connected to the
power supply’s output terminals using separate pairs of wires. It is recommended that each pair of
wires will be as short as possible and twisted or shielded to minimize noise pick-up and radiation.
The sense wires should be connected to the power supply output terminals or to the load with the
most critical load regulation requirement.
Sense lines. Twisted
pair or shielded.
23
Page 33
Load lines, twisted pair,
shortest length possible.
+V
Power
Supply
-
Rem.sense
-
Local sense
Local sense
+
+
Rem.sense
3.9.10 Multiple load connection with distribution terminals
If remotely located output distribution terminals are used, the power supply output terminals should
be connected to the distribution terminals by apair of twisted and/or shielded wires. Each load
should be separately connected to the remote distribution terminals (see Fig.3-14).
If remote sensing is required, the sensing wires should be connected to the distribution terminals or
at the most critical load.
+V
Power
Supply
Rem.sense
-
-
Local sense
Local sense
+
+
Rem.sense
-V
-V
Fig.3-13: Multiple loads connection, radial distribution, local sense
Distribution terminal
+V
-V
+
Load#1
-
+
Load#2
-
+
Load#3
-
+
Load#1
-
+
Load#2
-
+
Load#3
-
Fig.3-14: Multiple loads connection with distribution terminal
3.9.11Grounding outputs
Either the positive or negative output terminals can be grounded. To avoid noise problems caused
by common-mode current flowing from the load to ground, it is recommended to ground the output
terminal as close as possible to the power supply chassis ground.
Always use twowires to connect the load to the power supply regardless of how the system is
grounded.
WARNING
Models up to 60VDCRated Output shall not float outputsmore
than +/-60VDC above/below chassis ground. Models > 60VDC
Rated Output shall not float outputsmore than +/-600VDC
above/below chassis ground.
24
Page 34
WARNING
+S +LS
NC
-LS
-S
1
2
3
4
5
6
7
8
9
J2
OFF
ON
SW1
OUTPUT TERMINAL GROUNDING
There is a potential shock hazard at the RS232/485 and the IEEE portswhen
using power supplies with rated or combined voltage greater than 400V with the
Positive Output of the power supplies is grounded. Do not connect the Positive
Output to ground when using the RS232/485 or IEEE under the above conditions.
3.10 LOCAL AND REMOTE SENSING
The rear panel J2 sense connector is used to configure the power supply for local or remote
sensing of the output voltage. Refer to Fig.3-15 for sense connector location.
3.10.1 Sense wiring
WARNING
There isapotential shock hazard at the sense connector when using a power
supply with a rated output voltage greater than 40V. Local sense and remote
sense wires should have aminimum insulation rating equivalent or greater than
the maximum output voltage of the power supply. Ensure that the connections at
the load end are shielded to prevent accidental contact with hazardous voltages.
3.10.2 Local sensing
The power supply is shipped with the rear panel J2 sense connector wired for local sensing of the
output voltage. See Table 3-4 for J2 terminals assignment. With local sensing , the output voltage
regulation is made at the output terminals. This method does not compensate for voltage drop on
the load wires, therefore it is recommended only for low load current applications or where the load
regulation is less critical.
Terminal
J2-1
J2-2
J2-3
J2-4
J2-5
Fig.3-15: Sense connector location
Function
Remote positive sense (+S).
Local positive sense. Connected internally to the positive output terminal (+LS).
Not connected (NC).
Local negative sense. Connected internally to the negative output terminal (-LS).
Remote negative sense (-S).
Table 3-4: J2 terminals
25
Page 35
3.10.3 Remote sensing
WARNING
There isapotential shock hazard at the sense point when using power supply
with a rated output voltage greater than 40V. Ensure that the connections at the
load end are shielded to prevent accidental contact with hazardous voltages.
CAUTION
When using shielded sense wires, ground the shield
in one place only. The location can be the power
supply chassis or one of the output terminals.
Use remote sense where the load regulation at the load end is critical. In remote sense, the power
supply will compensate for voltage drop on the load wires. Refer to the power supply specifications
for the maximum voltage drop on load wires. The voltage drop is subtracted from the total voltage
available at the output. Follow the instructions below to configure the power supply for remote
sensing:
1. Ensure that the AC On/Off is in the Off position.
2. Remove the local sense jumpers from J2.
3. Connect the negative sense lead to terminal J2-5 (-S) and the positive sense lead to terminal
J2-1(+S) of the J2 mating connector. Ensure that the J2 mating connector is plugged securely
into the rear panel sense connector, J2.
4. Turn On the power supply.
Notes:
1. If the power supply is operating in remote sense and either the positive or negative load
wire is not connected, an internal protection circuit will activate and shut down the power
supply.To resume operation, turn the AC On/Off to the Off position, connect the open load
wire, and turn On the power supply.
2. If the power supply is operated without the remote sense lines or local sense jumpers, it will
continue to work, but the output voltage regulation will be degraded. Also, the OVP circuit may
activate and shut down the power supply.
3.10.4 J2 sense connector technical information
-J2 connector type: MC 1.5/5-G-3.81, Phoenix.
- Plug type: MC 1.5/5-ST-3.81, Phoenix.
-Wire AWG; 28 up to 16.
-Stripping length: 7mm.
-Tightening torque:1.95-2.21Lb-Inch. (
0.22- 0.25Nm)
3.11 REPACKAGING FORSHIPMENT
To ensure safe transportation of the instrument, contact the Lambda sales or service facility near
you for Return Authorization and shipping information. Please attach atag to the power supply
describing the problem and specifying the owner,model number and serial number of the power
supply.Refer to Warranty Information for further instructions.
26
Page 36
CHAPTER 4FRONT AND REAR PANEL CONTROLS
AND CONNECTORS
4.1INTRODUCTION
The Genesys Power Supplyseries has afullset of controls, indicators and connectors that allow
TM
theuserto easily setupand operate the unit. Beforestartingto operate the unit, please readthe
following sections forexplanationofthe functions of the controls andconnectors terminals.
- Section4.2:Front panel controls andindicators.
- Section4.3: Rear panel controls and connectors.
4.2FRONT PANEL CONTROLS AND INDICATORS
See Fig.4-1toreviewthe controls, indicators and meters located on the powersupply front panel.
6
CURRENT
POWER
1
VOLTAGE
2
ALARM
DC VOLTS
FINE
3
PREV/
OVP
UVL
FOLD
4
'
'
'
'
'
'
'
'
REM/LOC
5
DC AMPS
OUT
19
18
15
17
Fig.4-1: Front panel controls and indicators
Table4-1:Front Panel controls and indicators
Number
Control/Indicator
Description
High resolutionrotary encoder foradjusting the Output
1
VOLTAGE control
Voltage. Also adjuststhe OVP/UVL levels and selects
theAddress.
2
VOLTAGE indicator
Green LED,lightsfor Constant-Voltage mode
operation.
4digit, 7-segment LED display.Normally displays the
output voltage. When the PREV buttonispressed, the
3
VOLTAGE display
displayindicatesthe programmed settingofthe output
voltage. When the OVP/UVL buttonispressed,the
Voltage displayindicatesthe OVP/UVL setting.
16
14
11
13
7
9
10
12
8
Section
5.2.1
5.3.1
5.4.1
7.2.2
27
Page 37
Table 4-1: Front Panel controls and indicators
Number Control/Indicator Description
4 digit, 7-segment LED display.Normally displays the
4
CURRENT display
output current. When the PREV button is pressed, the
display indicates the programmed setting of output
current.
5
CURRENT indicator
Green LED, lights for Constant-Current mode operation.
High resolution rotary encoder for adjusting the Output
6
CURRENT control
Current. Also selects the Baud-Rate of the
communication port.
Main function
set the output On or Off. Press to reset and turn On the
output after OVPorFOLD alarm events have occurred.
Auxiliary function
7
OUT button
"Auto-Restart" modes. Press and hold OUT button to
toggle between "Safe-Start" and "Auto-Restart".The
VOLT display will cycle between "SAF" and "AU7”.
Releasing the OUT button while one of the modes is
displayed, selects that mode.
8
OUT indicator
Green LED, lights when the DC output is enabled.
Main function
unit into Local (REM/LOC button is disabled at Local
Lockout mode).
9
REM/LOC button
Auxiliary function
Press and hold REM/LOC for 3sec. to set the Address
with the VOLTAGE encoder and the Baud Rate with the
CURRENT encoder.
10
REM/LOC indicator
Green LED, lights when the unit is in Remote mode.
Foldback protection control.
- Press FOLD to set Foldback protection to On.
11
FOLD button
-To release Foldback alarm event, press OUT to
enable the output and re-arm the protection.
- Press FOLD again to cancel the Foldback protection.
12
FOLD indicator
Green LED, lights when Foldback protection is On.
:Output ON/OFF control. Press OUT to
: Selects between "Safe-Start" and
:Goto local. Press REM/LOCto put the
: Address and Baud Rate setting.
Section
5.2.2
7.2.4
5.6
5.11
7.2.5
7.2.2
7.2.4
5.5
13
14
OVP/UVL button
PREV/ button
Over VoltageProtection and Under Voltage limit setting.
- Press once to set OVP using VOLTAGE encoder ( the
current display shows“OUP” )
- Press again to set the UVL using VOLTAGE encoder
( the current display shows “UUL” ).
Main function
: Press PREV to display the output
voltage and current limit setting. For5sec. the display
will show the setting and then it will return to show the
actual output voltage and current.
Auxiliary function
: Front Panel Lock. Press and hold
PREV button to toggle between “Locked front panel”
and “Unlocked front panel”. The display will cycle
between “LFP” and “UFP”. Releasing the PREV button
while one of the modes is displayed, selects that mode.
28
5.3
5.4
5.17
Page 38
Table 4-1: Front Panel controls and indicators
Number Control/Indicator Description
15
PREV indicator
Green LED, lights when PREV button is pressed.
Section
Voltage and Current Fine/Coarse adjustment control.
Operates asatoggle switch. In Fine mode, the
16
FINE button
VOLTAGE and CURRENT encoders operate with high
resolution and in Coarse mode with lower resolution
(approx. 6 turns).
Auxiliary function
: Advanced Parallel Operation
5.15.2
Mode setting.
17
FINE indicator
Green LED, lights when the unit is in Fine mode.
Red LED, blinks in case of fault detection. OVP, OTP
18
ALARM indicator
Foldback, Enable and AC fail detection will cause the
ALARM LED to blink.
19
AC Power switch
AC On/Off control.
4.3 REAR PANEL
See Fig.4-2 to review the connections and controls located on the power supply rear panel.
Refer to Table 4-2 for explanations about the rear panel connections and controls.
9
8
10
ON
SW1
J2
OFF
6
7
J1
5
J3
IN
OUT
150~600V
Models
3
4
Fig.4-2: Rear panel connections and controls
Table 4-2: Rear panel connections and controls
Number
1
2
Item
AC input
connector
DC output
Description
Wire clamp connector. Three terminals for Single-Phase models
and four terminals for Three-Phase models.
Bus-bars for 8V to 100V models.
Wire clamp connector for 150V to 600V models (shown).
RJ-45 type connector, use for connecting power supplies to
3
Remote-In
connector
RS232 or RS485 port of computer for remote control purposes.
When using several power supplies inapower system, the first
unit Remote-In is connected to the computer and the remaining
units are chained, Remote-In to Remote-Out.
2
8~100V
Models
AC INPUT
1
Section
3.7
3.9.6
7.3
7.4
29
Page 39
Table 4-2: Rear panel connections and controls
1
2
3
4
5
6
7
8
9
Number
4
5
6
7
8
9
10
Item
Remote Out
connector
Programming
and
Monitoring
connector
SW1 Setup
switch
Remote
sense
connector
Blank
Sub-plate
IEEE
switch
Ground
stud
Description
RJ-45 type connector, used for chaining power supplies to form
a serial communication bus.
Connector for remote analog interface. Includes output voltage and
current limit programming and monitoring signals, Shut-off control
(electrical signal), Enable/Disable control (dry-contact), power
supply ok (PS_OK) signal and operation mode (CV/CC) signal.
Nine position DIPswitch for selecting remote programming and
monitoring modes for Output Voltage, Current Limit and other
control functions.
Connector for making remote sensing connections to the load
for regulation of the load voltage and compensation of load
wire drop.
Blank sub-plate for standard units. Isolated Remote Analog
programming connector for units equipped with Isolated
Analog control option (shown). IEEE connector for units
equipped with IEEE programming option.
Two position DIP switch for selecting IEEE mode or RS232/485
mode when IEEE option is installed.
M4 stud and hardware for chassis ground connection.
Section
7.3
7.4
4.5
4.4
4.4.1
4.4.2
3.8.2
3.10.2
3.10.3
4.4 REAR PANELSW1 SETUP SWITCH
The SW1 Setup switch (see Fig.4-3) isa9-position DIP switch that allows the user to choose the
following:
- Internal or remote programming for Output Voltage and Current Limit.
- Remote voltage or resistive programming of Output Voltage and Output Current limit.
- Select range of remote voltage and resistive programming.
- Select range of Output Voltage and Output Current monitoring.
- Select the Remote Shut-Off control logic.
- Select between RS232 or RS485 communication interface.
- Enable or disable the rear panel Enable/Disable control (dry contact).
Fig.4-3: SW1 setup DIP switch
30
Page 40
31
Page 41
4.5 REAR PANELJ1PROGRAMMING AND MONITORING CONNECTOR
The J1 Programming and Monitoring connector isaDB25 subminiature connector located on the
power supply rear panel. Refer to Table 4-4 for description of the connector functions. The power
supply default configuration is Local operation which does not require connections to J1. For remote
operation using J1 signals use the plug provided with power supply or equivalent type. It is essential
to use plastic body plug to conform with Safety Agency requirements. Ifashield is required for J1
wires, connect the shield toapower supply chassis ground screw.
4.5.1 Making J1 connections
-J1 connector type: AMP, P/N: 5747461-3
-J1 plug description: AMP, P/N: 745211-7
-Wire dimension range: AWG26-22
- Extraction tool: AMP, 91232-1 or equivalent.
-Manual Pistol grip tool:
Handle:AMP, P/N: 58074-1
Head:AMP, P/N: 58063-2
Before making any connection, turn the AC On/Off switch to the Off position and wait until the front
panel display has turned Off.
CAUTION
The programming return terminals (12, 22 and 23) are
referenced to the -V potential of the power supply.Do not
attempt to bias any of these terminals relative to the -V or
any other potential. Use the Isolated Programming interface
option to allow control fromaprogramming source at a
different potential relative to the power supply negative
output.
CAUTION
To prevent ground loops and to maintain the isolation of the
power supply when programming from J1, use an
ungrounded programming source.
WARNING
There isapotential shock hazard at the output when using a
power supply with rated output greater than 40V.Use wires
with minimum insulation rating equivalent to the maximum
output voltage of the power supply.
32
Page 42
33
Page 43
CHAPTER 5LOCAL OPERATION
5.1 INTRODUCTION
This Chapter describes the operating modes that are not involved in programming and monitoring
the power supply via its serial communication port (RS232/RS485) or by remote analog signals.
Ensure that the REM/LOC LED on the front panel is Off, indicating Local mode. If the REM/LOC
LED is On, press the front panel REM/LOC button to change the operating mode to local.
- For information regarding remote analog programming refer to Chapter 6.
- For information regarding usage of the serial communication port refer to Chapter 7.
5.2 STANDARD OPERATION
The power supply has two basic operating modes: Constant Voltage Mode and Constant Current
Mode. The mode in which the power supply operates at any given time depends on the output
voltage setting, output current limit setting and the load resistance.
5.2.1 Constant Voltage Mode
1. In constant voltage mode, the power supply regulates the output voltageat the selected value,
while the load current varies as required by the load.
2. While the power supply operates in constant voltage mode, the VOLTAGELED on the front panel
illuminates.
3.Adjustment of the output voltage can be made when the power supply output is enabled
(Output On)or disabled (Output Off). When the output is enabled, simply rotate the VOLTAGE
encoder knob to program the output voltage. When the output is disabled, press the PREV
button and then rotate the VOLTAGE encoder knob. The VOLTAGEmeter will show the
programmed output voltage for5seconds after the adjustment has been completed.Then the
VOLTAGEmeter will display "OFF".
4.Adjustment resolution can be set to coarse or fine resolution.
Press FINE button to select between the lower and higher resolution. The FINE LED turns On
when the resolution is set to FINE.
NOTE
If after completing the adjustment, the display shows a different value
than the setting, the power supply maybeat current limit. Check the
load condition and the power supply current limit setting.
NOTE
The maximum and minimum setting values of the output voltage are
limited by the Over Volt
Refer to Sec.5.3 and 5.4 for more details.
5.2.2 Constant Current Operation
1. In constant current mode, the power supply regulates the output current at the selected value,
while the voltage varies with the load requirement.
2. While the power supply is operating in constant current mode, the CURRENT LED on the front
panel illuminates.
3.Adjustment of the output current limit can be made when the power supply output is enabled
(Output On)or disabled (Output Off).
-Disabled output (Off): Press PREV button and then rotate the Current encoder knob. The
CURRENT meter will show the programmed current limit for 5 seconds after the adjustment
has been completed. Then the VOLTAGEmeter will display "OFF".
age protection and Under Voltage limit setting.
34
Page 44
- Enabled output, power supply in Constant Voltage mode: Press the PREV button and then
rotate the CURRENT encoder knob. The CURRENT meter will show the programmed
current limit for5seconds after the adjustment has been completed, and then will return to
show the actual load current.
- Enabled output, power supply in Constant Current mode: Rotate the CURRENT encoder
knob to adjust the current limit.
4. Adjustment resolution can be set to Coarse or Fine adjustment. Press the FINE button to
select between the Coarse and Fine resolution. The FINE LED turns On when the resolution
is set to FINE.
5.2.3 Automatic Crossover
If the power supply operates in Constant Voltage mode, while the load current is increased to greater
than the current limit setting, the power supply will automatically switch to Constant Current mode. If
the load is decreased to less than the current limit setting, the power supply will automatically switch
back to Constant Voltage mode.
5.3 OVER VOLTAGEPROTECTION(OVP)
The OVP circuit protects the load in the event ofaremote or local programming error orapower
supply failure. The protection circuit monitors the voltage at the power supply sense points and thus
providing the protection level at the load. Upon detection of an Over Voltage condition, the power
supply output will shut down.
5.3.1 Setting the OVP level
The OVP can be set when the power supply output is Enabled (On) or Disabled (Off). To set the OVP
level, press the OVP/UVL button, so that the CURRENT meter shows"OUP".
The VOLTAGEmeter shows the OVP setting level. Rotate the VOLTAGE encoder knob to adjust the
OVP level. The display will show "OUP" and the setting value for5seconds after the adjustment has
been completed and then will return to it's previous state.
The minimum setting level is approx. 105% of the set output voltage, or the value in Table 7-6,
whichever is higher. The maximum setting level is shown in Table5-1.
To preview the OVP setting, press OVP/UVL
pushbutton so that the CURRENT display will show
"OUP". At this time, the VOLTAGE display will show the
OVP setting. After5seconds, the display will return to
it's previous state.
Model
8V
10V
15V
20V
30V
40V
Max.
OVP
10.0V
12.0V
18.0V
24.0V
36.0V
44.0V
Model
60V
80V
100V
150V
200V
300V
600V
Max.
OVP
66.0V
88.0V
110.0V
165.0V
220.0V
330.0V
660.0V
Table 5-1: Maximum OVP setting levels
5.3.2 Activated OVP protection indications
When the OVPis activated the power supply
output shuts down. The VOLTAGE display shows
"OUP" and the ALARM LED blinks.
5.3.3 Resetting the OVP circuit
To reset the OVP circuit afterit activates:
1. Reduce the power supply Output Voltage setting below the OVP set level.
2. Ensure that the load and the sense wiring is connected properly.
3. There are four methods to reset the OVPcircuit.
3.1 Press OUT button.
3.2 Turn the power supply Off using theAC On/Off switch, wait until the front panel display turns
Off, then turn the power supply On using theAC On/Off switch.
3.3 Turn the power supply output Offand then On using the SO control (refer to sect.5.7). In this
method the power supply should be set toAuto-Restart mode.
3.4 Send OUT1 command via the RS232/485 communication port.
35
Page 45
5.4 UNDER VOLTAGE LIMIT (UVL)
The UVL prevents adjustment of the output voltage below a certain limit.The combination of UVL
and OVP functions, allow the user to create a protection window for sensitive load circuitry.
5.4.1 Setting the UVL level
Setting the UVL can be made when the power supply output is Enabled (On) or Disabled (Off). To set
the UVL level, press the OVP/UVL button TWICE, so that the CURRENT meter shows “UUL”. The
VOLTAGE meter shows the UVL setting level. Rotate the VOLTAGE encoder knob to adjust the UVL
level. The display will show “UUL” and the setting value for 5 seconds after the adjustment has been
completed and then will return to it’s previous state.
UVL setting values are limited at the maximum level to approximately 95% of the Output Voltage
setting. Attempting to adjust the UVL above this limit will result in no response to the adjustment
attempt. The minimum UVL setting is zero.
5.5 FOLDBACKPROTECTION
Foldback protection will shut down the power supply output if the load current exceeds the current limit
setting level. This protection is useful when the load circuitry is sensitive to an over current condition.
5.5.1 Settingthe Foldback protection
To arm the Foldback protection, the FOLD button should be pressed so that the FOLDLED illuminates.
In this condition, transition from Constant Voltage to Constant Current mode will activate the Foldback
protection. Activation of the Foldback protection disables the power supply output, causes the ALARM
LEDto blink and display "Fb" on the VOLTAGE meter.
5.5.2 Resetting activated Foldback protection
There are four methods to reset an activated Foldback protection.
1. Press the OUT button. The power supply output is enabled and the Output Voltage and current
will return to their last setting. In this method, the Foldback protection remains armed, therefore if
the load current is higher than the current limit setting, the Foldback protection will be activated
again.
2. Press the FOLD button to cancel the Foldback protection. The power supply output will be disabled
and the VOLTAGE display will show “OFF”.Press the OUT button to enable the power supply output.
3. Turn the power supply output Off and then On using the SO control (refer to sect. 5.7). In this method
the foldback protection remains armed, therefore if the load current is higher than the current limit
setting the Foldback protection will be activated.
4. Turn the power supply Offusing the AC On/Off switch, wait until the front panel display turns Off,
then turn the unit back ON again. The power supply output is enabled and the Output Voltage and
Current will return to their last setting. In this method, the Foldback protection remains armed,
therefore if the load current is higher than the current limit setting, the Foldback protection will be
activated again.
5.6 OUTPUT ON/OFF CONTROL
TheOutput On/Off enables or disables the power supply output. Use this function to make adjustments
to either the power supply or the load without shutting off the AC power.The Output On/Off can be
activated from the front panel using the OUT button or from the rear panel J1 connector.The OUT
button can be pressed at any timeto enable or disable the power supply output. When the output is
disabled, the output voltage and current fall to zero and the VOLTAGE display shows“OFF”.
5.7 OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR
Contacts 2,3 and 15 of J1 (Fig.4-2, Item 5) serve as Output Shut-Off (SO) terminals. The SO terminals
accept a 2.5V to 15V signal or Open-Short contact to disable or enable the power supply output. The
SO function will be activated only when a transition from On to Offis detected after applying AC power
to unit. (Thus ,inAuto-Restart mode, the output will be enabled after applying AC power, even if SO is in
Off level.). After On to Off transition is detected, the SO will enable or disable the power supply output
according to the signal level or the short/open applied to J1.This function is useful for connecting power
supplies ina“Daisy-chain” (refer to section 5.16). TheSO control can be used also to reset the OVP
and Fold Protection. Refer to sect. 5.3 and 5.5 for details.
36
Page 46
When the unit is shut-offbyJ1 signal, the VOLTAGE display will show “SO” to indicate the unit state. J1
*AC fail
*Output Off
contact 15 is the SO signal input and contacts2and 3, IF_COM, are the signal return (connected
internally). Contacts 2,3 and 15 are optically isolated from the power supply output.
The SO control logic can be selected by the rear panel SW1 Setup switch. Refer to Table 5-2 for SW1
setting and SO control logic.
SW1-5 setting
Down (default)
Up
SO signal level
J1-2(3), 15
2-15V or Open
0-0.6V or Short
2-15V or Open
0-0.6V or Short
Power supply
output
On
Off
Off
On
Display
Voltage/Current
“SO”
“SO”
Voltage/Current
Table 5-2: SO logic selection
5.8 ENABLE/DISABLE CONTROL VIA REAR PANELJ1 CONNECTOR
Contacts1and 14 of J1 (Fig.4-2, Item 5) serve as Output Enable/Disable terminals by switch or relay.
This function is enabled or disabled by the SW1 Setup switch position 9. Refer to Table 5-3 for
Enable/Disable function and SW1 setting.
SW1-9 setting
Down (Default)
Up
Enable/Disable inputs
Open or Short
Open
Short
Table 5-3: Enable/Disable function and SW1 setting
Power supply output
On
Off
On
Display
Voltage/Current
“ENA”
Voltage/Current
ALARM LED
Off
Blinking
Off
CAUTION
To prevent possible damage to the unit, do not connect any of the
Enable/Disable inputsto the positive or negative output potential.
NOTE
Safe Start mode
Auto Restart mode
-If the Enable/Disable fault condition clears when unitsin safe start mode
recovery is by pressing OUT button or by sending a ‘OUT1’ serial command.
- The output will return back ON automatically when the Enable/Disable
fault conditions clears.
5.9 CV/CC SIGNAL
CV/CC signal indicates the operating mode of the power supply, Constant Voltage or Constant Current.
CV/CC signal is an open collector output with a 30V parallel zener,at J1-13, referenced to the COM
potential at J1-12 (connected internally to the negative sense potential). When the power supply
operates in Constant Voltage mode, CV/CC output is open. When the power supply operates in Constant
Current mode, CV/CC signal output is low(0-0.6), with maximum 10mA sink current.
CAUTION
Do not connect CV/CC signal toavoltage source higher than 30VDC.
Always connect CV/CC signal to the voltage source with a series resistor
to limit the sink current to less than 10mA.
5.10 PS_OK SIGNAL
PS_OK signal indicates fault condition in the power supply. PS_OK is a TTL signal output at J1-16,
referenced to IF_COM at J1-2,3 (Isolated Interface Common)). When a fault condition occurs, PS_OK
level is low, with maximum sink current of 1mA, when no fault condition occurs, PS_OK level is high with
maximum source current of 2mA. The following faults will set the PS_OK to Fault state:
*OTP
*OVP
*Foldback
*Enable/Disable open (Power supply is disabled)
*SO (Rear panel Shut-Off-Power supply is shut off))
*IEEE failure (with optional IEEE interface)
37
Page 47
5.11 SAFE START AND AUTO-RESTART MODES
When turning on the power supply AC On/Off,it can start to its last setting of Output Voltage and
Current limit with the output enabled (Auto-restart) or start with the output disabled (Safe mode).
Press and hold the OUT button to select between Safe start and Auto-restart modes. The VOLTAGE
display will continuously cycle between "SAF" and "AU7” every 3 seconds. Releasing OUT
pushbutton while one of the modes is displayed, selects that mode. The default setting at shipment
is Safe mode.
5.11.1Automatic start mode
In this mode, the power supply restores its last operation setting. Upon start-up, the output is
enabled or disabled according to its last setting.
5.11.2Safe start mode
In this mode, the power supply restores its last operation setting and sets the Output to Offstate. At
start-up, the output is disabled and the output voltage and current are zero. To enable the output and
restore the last output voltage and current limit values, momentarily press OUTbutton.
5.12 OVER TEMPERATURE PROTECTION(OTP)
The OTP circuit shuts down the power supply before the internal components can exceed their safe
internal operating temperature. When an OTP shutdown occurs, the display shows"O7P" and the
ALARM LED blinks.
Resetting the OTP circuit can be automatic (non-latched) or manual (latched) depending on the
Safe or Automatic restart mode.
1. Safe start mode:
condition has been removed. The display continue to shows"O7P" and the ALARM LED
continues to blink. To reset the OTP circuit, press OUT button (or send OUT ON command via the
serial port).
2. Auto-restart mode:
automatically when the over temperature condition is removed.
5.13 LAST SETTING MEMOR
The power supply is equipped with Last Setting Memory,which stores power supply parameters at
eachAC turn-off sequence.
STORED PARAMETERS:
1. OUT On or Off
2. Output voltage setting (PV setting)
3. Output current limit (PC setting)
4. OVP setting
5. UVL setting
6. FOLD setting
7. Start-up mode (Safe or Auto-rest
8. Remote/Local:If the last setting was Local Lockout (latched mode), the supply will return to
Remote mode (non-latched).
9.Address setting
10. Baud rate
11. Locked /Unlocked front panel (LFP/UFP)
(Items8,9,10 are related to Remote digital control operation and explained in chapter 7)
12. Master/Slave setting
In Safe start mode, the power supply stays offafter the over temperature
InAuto-restart mode , the power supply recovers to it's last setting
Y
art)
5.14 SERIES OPERATION
Power supplies of the SAME MODEL can be connected in series to obtain increased output voltage.
Split connection of the power supplies gives positive and negative output voltage.
38
Page 48
CAUTION
Do not connect power supplies from different
manufacturers in series or in parallel.
5.14.1 Series connection for increased output voltage
In this mode, two units are connected so that their outputs are summed. Set the current limit of
each power supply to the maximum that the load can handle without damage. It is
recommended that diodes be connected in parallel with each unit output to prevent reverse
voltage during start up sequence or in case one of the units shuts down. Each diode should be
rated to at least the power supply rated output voltage and output current. Refer to Fig.5-1 and
5-2 for series operation with local and remote sensing.
WARNING
When power supplies are connected in series, and
the load or one of the output terminals is grounded,
no point maybeatagreater potential of +/-60VDC
from ground for models up to 60VDCRated Output
and +/-600VDC from ground for models >60VDC
Rated Output. When using RS232/485 or IEEE, refer
to the OUTPUT TERMINALS GROUNDING
warning, section 3.9.11.
+S
+LS
-LS
+LS
-LS
+S
-S
-S
+
(*)
-
+
LOAD
-
+
(*)
-
(*) Diodes are
user supplied.
POWER
SUPPLY
POWER
SUPPLY
Fig.5-1: Series connection, local sensing
Remote programming in series operation for increased output voltage:
1.Programming by external voltage:
2.Using the SO function and PS_OK signal:
+S
+LS
-LS
+LS
-LS
-S
+S
-S
+
(*)
-
+
LOAD
-
+
(*)
-
POWER
SUPPLY
POWER
SUPPLY
Fig.5-2: Series connection, remote sensing
The analog programming circuitsof this power supply
are referenced to the negative output potential.
Therefore, the circuits used to control each series
connected unit must be separated and floated from
each other.
The Shut-Off and PS_OK circuits are referenced to the
isolated interface common, IF_COM (J1-2,3). The
IF_COM terminals of different units can be connected
to obtainasingle control circuit for the power supplies
connected in series.
39
Page 49
3. Programming by external resistor:
Programming by external resistor is possible . Refer to
section 6-5 for details.
4. Programming via the Serial
Communication port (RS232/RS485):
The communication port is referenced to the IF_COM
which is isolated from the power supply output
potential. Therefore power supplies connected in
series can be chained using the Remote-In and
Remote-Out connectors. Refer to chapter 7 for details.
5.14.2 Series connection for positive and negative output voltage
In this mode, two units are configured as a positive and negative output. Set the current limit of each
power supply to the maximum that the load can handle without damage. It is recommended that
diodes be connected in parallel with each unit output to prevent reverse voltage during start-up or in
case one of the units shuts down. Each diode should be rated to at least the power supply rated
output voltage and output current. Refer to Fig.5-3 for this operating mode.
+S
+LS
+LS
+S
-S
-S
+
(*)
-
LOAD
+
COM.
-
+
(*)
(*) Diodes are user supplied.
-
POWER
SUPPLY
-LS
POWER
SUPPLY
-LS
Fig.5-3: Series connection for positive/negative output voltages
Remote programming in series operation for positive and negative output voltage
1. Programming by external voltage:
The analog programming circuitsof this power supply
are referenced to the negative output potential.
Therefore, the circuits used to control each series
connected unit must be separated and floated from
each other.
2. Using the SO function and PS_OK
signal :
The Shut-Off and PS_OK circuits are referenced to the
isolated interface common, IF_COM (J1-2,3). The
IF_COM terminals of the units can be connected to
obtain a single control circuit for the power supplies
connected in series.
3. Programming by external resistor :
Programming by external resistor is possible. Refer
to section 6.5 for details.
4. Programming via the Serial
Communication port (RS232/RS485):
The communication port is referenced to the IF_COM
which is isolated from the power supply output
potential. Therefore power supplies connected in
series can be chained using the Remote-In and
Remote-Out connectors. Refer to chapter 7 for details.
40
Page 50
5.15 PARALLEL OPERATION
Up to four units of the same VOLTAGE and CURRENT rating can be connected in parallel to provide
up to four times the output current capability. One of the units operates as a master and the
remaining units are slaves. The slave units are analog programmed by the master unit.
In remote digital operation, only the master unit can be programmed by the computer while the slave
units may be connected to the computer for voltage, current and statusreadback only.
There are two methods, basic and advanced, to configure multiple supplies for parallel operation.
With both methods, Power Supplies, should be connected in a Daisy-Chain configuration.
Refer to Sec. 5.15.1, to Sec. 5.15.2 and to Sec.5.16 for detailed explanation.
5.15.1 Basic parallel operation
In this method, setting the units as Master and Slaves is made by the rear panel J1 connections and
the setup switch SW1. Each unit displays its own output current and voltage. To program the load
current, the Master unit should be programmed to the total load current divided by the number of
units in the system. Refer to the following procedure to configure multiple supplies for simple parallel
operation.
1. Setting up the Master unit
Set the master unit output voltage to the desired voltage. Program the current limit to the
desired load current limit divided by the number of parallel units. During operation, the master
unit operates in CV mode, regulating the load voltage at the programmed output voltage.
Connect the sensing circuit to local or remote sensing as shown in Fig.5-4 or Fig.5-5.
2. Setting up the slave units
-1.The output voltage of the slave units should be programmed 2%~5% higher than the output
voltage of the master unit to prevent interference with the master unit's control.
The current limit of each unit should be programmed to the desired load current limit
divided by the number of parallel units.
-2.Set the rear panel setup switch SW1 position 2 to it's up position.
-3.Set the rear panel setup switch SW1 position 3 in the same position as
SW1 position 4 of the master.
-4.Connect short between J1-8 and J1-12 (refer to Table 4-4.)
-5. Connect J1 terminal 10(IPGM) of the slave unit to J1 terminal 25(P) of the master unit.
-6. Connect J1 terminal 23(IPGM_RTN) of the slave unit to J1 terminal 12(COM) of the master
unit.
During operation the slave units operate as a controlled current source following the master
output current. It is recommended that the power system is designed so that each unit supplies
up to 95% of its current rating because of the imbalance which may be caused by cabling and
connections voltage drop.
3. Setting Over Voltage protection
The master unit OVP should be programmed to the desired OVP level. The OVP of the slave
units should be programmed to a higher value than the master OVP. When the master unit
shuts down, it programs the slave unit to zero output voltage. If a slave unit shuts down
(when its OVP is set lower than the master output voltage), only that unit would shut down
and the remaining slave units would supply all the load current.
4. Setting Foldback protection
Foldback protection if desired, may only be used with the master unit. When the master unit
shuts down it programs the slave units to zero output voltage.
5. Connection to the load
In parallel operation, power supplies can be connected in local or remote sensing. Refer to
Fig.5-4 and 5-5 for typical connections of parallel power supplies. The figures show
5.15.2 Advanced parallel operation
In this method, multiple supplies can be configured to parallel operation as a single power supply.
The total load current and output voltage are displayed by the Master unit and can be readback
from the Master unit. The Slave units display only their operating status (On, Off or Fault
condition).
Refer to the following procedure to configure multiple supplies for Advanced parallel operation.
1. Basic configuration
Repeat steps 1 to 5 in Sec. 5.15.1 (Basic parallel operation).
41
Page 51
2. Setting the unitsasMaster or Slave
a) Depress and hold the FINE button for3seconds. The Master/Slave configuration will be
displayed on the Current Display.Rotate the CURRENT encoder to obtain the desired mode.
Refer to Table 5-4 for the CURRENT display and modes of operation.
CURRENT Display
H1
H2
H3
H4
S
Single supply(default)
Master supplywith1Slave supply
Master supplywith2Slave supplies
Master supplywith3Slave supplies
Slave supply
Operating Mode
Table 5-4: Setting mode of operation
b) When the desired configuration is obtained, depress and release the FINE button or wait
approx. 5 seconds.
3. Master and Slave units default operation
a) When a unit is programmedto Slave mode it enters the Remote mode with Local Lockout. In
this mode, the front panel controls are disabled to prevent accidental setting change (refer to Sec.
7.2.7 for details).
b) The Slave unitsparameters will automatically set the following:
*Output voltage to approximate. 102% of rated output voltage.
*ProgrammedCurrent to zero.
*UVL to zero volts
*AST On
*OUT On
*Foldback protection Off
*OVP to itsmaximum value
c) The Master and Slave modes are stored in the power supply EEPROM when the AC power is
Turned off. The system will return to the Master/Slave mode upon re-application of AC power.
4. CURRENT display accuracy
In the advanced parallel mode, the total current is programmed and reported by the Master.In
this method, the CURRENT display accuracy is 2%+/- 1 count. In cases that higher accuracy is
required, it is recommended to use the basic parallel operation mode.
5. To release units from Slave mode
Slave units can be released using the following procedure:
a) Depress FINE button for3seconds. The Master/Slave configuration will be displayed on the
CURRENT display.
b) Select H1 mode using the CURRENT encoder.
c) Depress FINE button again or wait 5 seconds.
d) Turn the AC power Offto store the new setting.
e) After exiting from Slave operation the unit’s parameters will be set to:
*Programmed Voltage to zero *AST OFF
*Programmed Current to zero *OUT OFF
*UVL to zero volts *Foldback protection OFF
*OVP to its maximum value *Locked Front Panel
J1-12 COM
+S
+LS
IPGM_RTN
J1-23
+S
+V
+V
-S -LS
To J1-10
SLAVE#2
POWER SUPPLY
To J1-23
SLAVE#2
POWER SUPPLY
CAUTION
Make sure that the connection between -Vo terminals is
reliable to avoid disconnection during operation.
Disconnection may cause damage to the power supply.
MASTER
POWER SUPPLY
J1-25
P
IPGM
J1-12
J1-8
J1-10
SLAVE#1
POWER SUPPLY
-S -LS
+LS
As shortas possible
-V
-V
42
Twisted
pair
+
LOAD
-
Fig.5-4: Parallel connection
with local sensing
VORSICHT
Stellen Sie sicher, dass die Verbindung zwischen den -V
Anschlussklemmen sich nicht während des Betriebs
lösen kann. Eine Unterbrechung kann die Netzteile
beschädigen.
Page 52
NOTE
Use PREV button to preview the output voltage and current setting or to unlock the front panel.
NOTE
With local sensing it is important to minimize the wire length and resistance. Also the
positive and negative wire resistance should be close as possible to each other to achieve
current balance between power supplies.
+S
-S
To J1-10
SLAVE#2
POWER SUPPLY
To J1-23
SLAVE#2
POWER SUPPLY
MASTER
POWER SUPPLY
J1-25
P
IPGM
J1-12
J1-8
SLAVE#1
POWER SUPPLY
J1-10
+S-S
+S-S
J1-12 COM
IPGM_RTN
J1-23
Twisted
pair
As shortas possible
+V
-
V
V
+
-V
Twisted
pair
-S
+S
Twisted
pair
+S
Make sure that the
connection between -Vo
terminals is reliable to
+
LOAD
-
avoid disconnection
during operation.
Disconnection may cause
damage to the power
-S
supply.
CAUTION
Fig.5-5: Parallel operation with Remote sensing
5.16 DAISY-CHAIN CONNECTION
It is possible to configure amultiple power supply system to shut down all the unitswhen a fault
condition occurs in one of the units. When the fault is removed, the system recovers according to its
setting to Safe start mode or Automatic restart.
Setup switch SW1 position 5 should be set to itsDown position to enable the Daisy-chain operation.
Other SW1 positions can be set according to the application requirements.
Ifafault occurs in one of the unitsits PS_OK signal will be set to low level and the display will indicate
the fault. The other unitswill shut off and their display will indicate "SO”. When the fault condition is
removed, the unitswill recover to their last setting according to their Safe start or Auto-restart setting.
Fig.5-6 shows connection of three units, however the same connection method applies to systems
with a larger number of units.
POWER SUPPLY
#
1
J1-16
J1-2,3
IF_COM
PS_OK
J1-15
SO
POWER SUPPLY
#
J1-2,3
IF_COM
2
J1-16
PS_OK
J1-15
SO
POWER SUPPLY
#3
J1-2,3
J1-16
IF_COM
PS_OK
J1-15
SO
Fig.5-6: Daisy-chain connection
5.17 FRONT PANELLOCKING
The front panel controls can be locked to protect from accidental power supply parameter change.
Press and hold PREV button to toggle between “Locked front panel” and “Unlocked front panel”.
The display will cycle between “LFP” and “UFP”. Releasing the PREV button while one of the
modes is displayed, selects that mode.
5.17.1 Unlocked front panel
In this mode, the front panel controls are enable to program and monitor the power supply
parameters.
5.17.2 Locked front panel
In this mode the following front panel controls are disabled:
- VOLTAGE and CURRENT encoders.
- FOLD button.
- OUT button.
The power supply will not respond to attemptsto use these controls. The VOLT display will show
“LFP” to indicate that the front panel is locked.
OVP/UVL button is active to preview the OVPand UVL setting.
43
Page 53
CHAPTER 6 REMOTE ANALOG PROGRAMMING
6.1 INTRODUCTION
The rear panel connector J1 allows the user to program the power supply output voltage and current
limit with an analog device. J1 also provides monitoring signals for output voltage and output current.
The programming range and monitoring signals range can be selected between 0-5V or 0-10V
using the setup switch SW1. When the power supply is in Remote Analog programming, the serial
communication port is active and can be used to read the power supply parameters.
CAUTION
COM (J1-12), VPGM_RTN (J1-22) and IPGM_ RTN (J1-23) terminals of J1
are referenced to the -Vout potential (-V). Do not connect these terminals to
any potential other than -Vout (-V), as it may damage the power supply.
6.2 LOCAL /REMOTEANALOG CONTROL
Contact 8ofJ1 (Fig. 4-2, item 5) accepts TTL signal or Open-Short contact (referenced to J1-12) to
select between Local or Remote Analog programming of the output voltage and current limit.
In Local mode, the output voltage and current limit can be programmed via the front panel VOLTAGE
and CURRENT encoders or via the RS232/485 port. In Remote Analog mode, the output voltage
and current limit can be programmedby analog voltage or by programming resistors via J1 contacts
9 and 10 (refer to sec. 6.4 and 6.5). Refer to Table 6-1 for Local/Remote Analog control (J1-8)
function and Setup switch SW1-1, 2 setting.
SW1-1,2 setting
Down (default)
Up
Table 6-1: Local/Remote Analog control function
J1-8 function
No effect
"0" or Short
"1" or Open
Output voltage/
Current setting
Local
Remote Analog
Local
6.3 LOCAL/REMOTEANALOGINDICATION
Contact 21 of J1 (Fig. 4-2, item 5) is an open collector output that indicates if the power supply is in
Local mode or in Remote Analog mode. To use this output, connect a pull-up resistor toavoltage
source of 30Vdc maximum.Choose the pull-up resistor so that the sink current will be less than 5mA
when the output is in low state. Refer toTable 6-2 for J1-21 function.
J1-8
TTL "0" or short
TTL "1" or open
Table 6-2: Local/Remote Analog indication
SW1-1
Down
Down
Up
Up
Down or Up
SW1-2
Down
Up
Down
Up
Down or Up
J1-21 signal
Open
0~0.6V
0~0.6V
0~0.6V
Open
44
Page 54
6.4 REMOTE VOLTAGEPROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT
CAUTION
To maintain the isolation of power supply and prevent ground loops, use an
isolated programming source when operating the power supply via remote
analog programming at J1 connector.
Perform the following procedure to set the power supply to Remote Voltage programming :
1. Turn the power supply AC On/Off switch to Off.
2. Set setup switch SW1-1 to itsUP position for output voltage external programming and
SW1-2 to itsUP position for Output Current limit external programming.
3. Set SW1 position3to select programming voltage range according to Table 6-3.
4. Ensure that SW1 positions7and8are at their Down (default) position.
5. Connect a short between J1-8 and J1-12 (refer to Table 4-4).
6. Connect the programming source to the mating plug of J1 as shownin Fig.6-1. Observe
correct polarity for the voltage source.
7. Set the programming sources to the desired levels and turn the power supply ON. Adjust the
programming sources to change the power supply output.
NOTES:
1. SW1 positions 4,5,6 and9are not required for remote programming. Their setting can be
determined according the application.
2. The control circuits allow the user to set the output voltage and current limit up to 5% over
the model-rated maximum value. The power supply will operate within the extended range,
however it is not recommended to operate the power supply over its voltage and current
rating and performance is not guaranteed.
SW1-3 setting
UP
DOWN
Table 6-3: SW1-3 setting and programming range
Output Voltage programming
VPGM (J1-9)
0-10V
0-5V
Current limit programming
IPGM (J1-10)
0-10V
0-5V
J1 connector, rear panel view
CURRENT LIMIT
PROGRAMMING
+
-
12
13
25
23
10
9
22
OUTPUT VOLTAGE
PROGRAMMING
8
-
+
1
14
Fig.6-1: Remote voltage programming connection
45
Page 55
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT
For resistive programming, internal current sources, for output voltage and/or output current control,
supply 1mA current through external programming resistors connected between J1-9&22 and J1-10
& 23. The voltage across the programming resistors is used asaprogramming voltage for the power
supply.Resistance of 0~5Kohm or 0~10Kohm can be selected to program the output voltage and
current limit from zero to full scale.
A variable resistor can control the output over its entire range, oracombination of variable resistor
and series/parallel resistors can control the output over restricted portion of its range.
Perform the following procedure to set the power supply to Resistive programming:
1. Turn the AC On/Off switch to Off.
2. Set setup switch SW1-1 to itsUP position for output voltage external programming and
SW1-2 to itsUP position for Output Current limit external programming.
3. Set SW1 position 3to select programming resistor range according to Table 6-4.
4. Set SW1-7 to itsUP position for output voltage resistive programming and
SW1-8 to itsUP position for Output Current limit resistive programming.
5. Connect a short between J1-8, J1-12 and J1-23 (refer to Table 4-4).
6. Connect the programming resistors to the mating plug of J1 as shownin Fig.6-2.
7. Set the programming resistors to the desired resistance and turn the power supply ON.
Adjust the resistors to change the power supply output.
NOTES:
1. SW1 positions 4, 5, 6 and9are not required for remote programming. Their setting can be
determined according to the application requirements.
2. The control circuits allow the user to set the output voltage and current limit up to 5% over
the model-rated maximum value. The power supply will operate within the extended range,
however it is not recommended to operate the power supply over its voltage and current
rating and performance is not guaranteed.
3. To maintain the temperature stability specification of the power supply, the resistors used for
programming should be stable and low noise resistors, with temperature coefficient of less
than 50ppm.
4. When resistive programming is used, front panel and computer control (via serial communication
port) of output voltage and current are disabled.
PROGRAMMING
RESISTOR
OPTIONAL SETS
LOWER LIMIT
OPTIONAL SETS
UPPER LIMIT
SW1-3 setting
UP
DOWN
Output Voltage programming
VPGM (J1-9)
0-10Kohm
0-5Kohm
Current limit programming
IPGM (J1-10)
Table 6-4: SW1-3 setting and programming range
J1 connector, rear panel view
CURRENT LIMIT
PROGRAMMING
13
25
12
10 9
23
22
OUTPUT VOLTAGE
PROGRAMMING
8
Fig.6-2: Remote resistive programming
46
0-10Kohm
0-5Kohm
PROGRAMMING
RESISTOR
1
14
OPTIONAL SETS
LOWER LIMIT
OPTIONAL SETS
UPPER LIMIT
Page 56
6.6 REMOTE MONITORINGOF OUTPUTVOLTAGE AND CURRENT
The J1 connector, located on the rear panel provides analog signals for monitoring the output
voltage and output current. Selection of the voltage range between 0-5V or 0-10V is made by
setup switch SW1-4. The monitoring signals represent 0to 100% of the power supply output
voltage and output current.The monitor outputs have 500 ohm series output resistance. Ensure
that the sensing circuit has an input resistance of greater than 500 Kohm or accuracy will be
reduced.
Refer to Table 6-5 for required J1 connection, SW1-4 setting and monitoring voltage range.
Signal
name
VMON
IMON
VMON
IMON
Signal function
Vout monitor
Iout monitor
Vout monitor
Iout monitor
Table 6-5 Monitoring signals setting
Notes:
1.Radiated emissions, FCC requirements:
2. Front panel encoders operation:
3. Front panel PREV button:
J1 connection
Signal (+)
J1-11
J1-24
J1-11
J1-24
FCC requirements for radiated emissions, use
shielded cable for the analog control signals. In case of
using unshielded cable, attach an EMI ferrite
suppressor to the cable, as close as possible to the
power supply.
In Remote analog mode the output voltage and
current can’t be set by the VOLTAGE and CURRENT
encoders.
Use PREV button to display the output voltage and
current setting defined by the encoders or
communication.
Return (-)
J1-12
J1-12
Range
0-5V
0-10V
SW1-4
Down
Up
4. Communication:
In Remote analog mode, power supply parameters
can be programmed and readback via the
communication port except output voltage and current
setting.
47
Page 57
CHAPTER 7 RS232&RS485 REMOTE CONTROL
7.1 INTRODUCTION
This chapter describes the operation of the Genesys 3300W power supplies via the serial
communication port. Details of the initial set-up, operation via RS232 or RS485, the command set
and the communication protocol are described in this chapter.
TM
7.2 CONFIGURATION
7.2.1 Default setting
The power supply is shipped with the following setting:
-Address:
-Baud-rate:
-RS232/485:
-Vout setting:
-Iout setting:
-Master/Slave
7.2.2 Address setting
The power supply address can be set to any address between0and 30. Follow the instructions
described below to set the address.
1. If the unit is in Remote mode (front panel REM/LOC LED illuminates), press REM/LOC
button to put the unit into Local mode.
2. Press and hold for approximately 3sec. the REM/LOC button. The VOLTAGE display will
indicate the communication port address.
3. Using the VOLTAGE adjust encoder, select the address.
6
9600
RS232
0
Maximum
H1 (Master)
-Output:
-Start up mode:
-OVP:
-UVL:
-Foldback:
-Front panel:
Off
Safe start
Maximum
0
Off
Unlocked (UFP)
To preview the address at any time, press and hold the REM/LOC button for approx. 3sec. The
VOLTAGE display will indicate the power supply address.
7.2.3 RS232 or RS485 selection
To select between RS232 or RS485 set the rear panel setup switch SW1-6 position to:
-Down for RS232
-Up for RS485
7.2.4 Baud rate setting
Five optional rates are possible: 1200, 2400, 4800, 9600 and 19200. To select the desired rate,
the following steps should be taken:
1. If the unit is in Remote mode (front panel REM/LOC LED illuminates), press REM/LOC
button to put the unit into Local mode.
2. Press and hold for approx. 3sec. the REM/LOC button. The CURRENT display will show
the communication port Baud Rate.
3. Using the CURRENT adjust encoder, select the desired Baud Rate.
7.2.5 Setting the unit into Remote or Local mode
1. The unit will be put into Remote mode only via serial communication command.
Commands that will put the unit into Remote mode are:
RST PV n
OUT nPCn
RMT n
(for n values see Tables 7-3, 7-4, 7-5 and 7-6)
48
Page 58
2. There are two Remote modes:
1. Remote:
In this mode, return to local can be made by the front panel REM/LOC or via
serial port command RMT 0. Set the unit into Remote mode via serial port
RMT 1 command.
2. Local Lockout:
In this mode the unit can be returned to Remote mode via the serial port
RMT 1 command or by turning off the AC power until the display turns off
and then turn it to on again. In Local Lockout mode, the front panel
REM/LOC button is not active. Set the unit into Local Lockout mode via
serial port RMT 2 command.
7.2.6 RS232/485 port in Local mode
When the power supply is in local mode, it can receive queries or commands. Ifaquery is received,
the power supply will reply and remain in Local mode. Ifacommand that affects the output is
received, the power supply will perform the command and change to Remote mode.
Serial commands may be sent to set the status registers and read them while the unit is in Local
mode. If the Enable registers are set (refer to section 7.8) the power supply will transmit SRQ’s while
in Local.
7.2.7 Front panel in Remote mode
Front panel control in Remote mode is disabled except for:
1. PREV: use to preview the Voltage and Current limit setting.
2. OVP/UVL: use to preview the OVP/UVL setting.
3. LOC/REM: use to set the unit into Local mode.
In Local Lockout mode, only PREV and OVP/UVLare active.
7.3 REAR PANELRS232/485 CONNECTOR
The RS232/485 interface is accessible through the rear panel RS232/485 IN and RS485 OUT
connectors. The connectors are 8 contact RJ-45. The IN and OUT connectors are used to connect
power supplies in a RS232 or RS485 chain to a controller. Refer to Fig.7-1 for IN/OUT connectors
SG
TXD
RXD
NC
+
-
NC
RXD
TXD
NC
+
-
TXD
RXD
TX
SG
-
+
RX
RXD
TXD
NC
-
+
Shield
87654321
OUT
87654321
IN
(connector enclosure)
Fig.7-1: J3 rear panel IN/OUT connectors pinout
NOTE
Tx and Rx are used for RS232 communication. Txd +/- and Rxd +/- are used for RS485
communication. Refer to RS232 and RS485 cables description for connection details.
49
Page 59
50
Page 60
7.4.2 Multi power supply connection to RS232 or RS485 bus
Daisy-chain up to 31 units can be connected to RS232 or RS485 bus. The first unit connectsto the
controller via RS232 or RS485 and the other units are connected with RS485 bus, the user must set
all slave supplies toaunique address. No two supplies may have the same address.
1. First unit connection: Refer to section 7.4.1 for connecting the first unit to the controller.
2. Other units connection: The other unitson the bus are connected via their RS485 interface.
Refer to fig.7-5 for typical connection.
- Set rear panel setup switch SW1-6 to it's UP position
- Using the Linking cable supplied with each unit (refer to Fig.7-6), connect each unit OUT
connector to the next unit IN connector.
*I
tis recommended when using ten or more power supplies in Daisy-chain system to connect a
120 ohm resistive termination at the last unit’s RS485 OUT connector.
120 W between TXD and TXD
120 W between RXD and RXD
RS232/485
+-
+-
RS485
RS485
RS485
RS485
IN
POWER SUPPLY
OUT
#1
IN
POWER SUPPLY
OUT
#2
IN
POWER SUPPLY
OUT
#3
IN
POWER SUPPLY
OUT
#31
Fig7-5: Multi power supplies RS232/485 connection
L=0.5m typ.
NAME
SHIELD
SG
-
TXD
+
TXD
-
RXD
+
RXD
8PIN CONNECTOR (OUT)
PIN NO.
HOUSING
1
6
3
5
4
NAME
SHIELD
SG
-
RXD
+
RXD
TXD
+
TXD
-
Fig.7-6:
1
8
8PIN CONNECTOR (IN)
PIN NO.
HOUSING
1
6
3
5
4
Serial link cable with RJ-45 shielded connectors (P/N: GEN/RJ45)
7.5 COMMUNICATIONINTERFACEPROTOCOL
The address (ADR n) command must return an “OK” response before
NOTE
any other commands are accepted.
7.5.1 Data format
Serial data format is8bit, one start bit and one stop bit. No parity bit.
7.5.2 Addressing
The Address is sent separately from the command.
It is recommended to add a 100 msec software delay between queryor sent command to
next unit addressing.
Refer to section 7.7.3 for details.
RS485
120 OHM
TERMINATION
8
1
7.5.3 End of Message
The end of message is the Carriage Return character (ASCII 13). The power supply ignores the Line
Feed (ASCII 10) character.
7.5.4 Command Repeat
The backslash character “\” will cause the lastcommand to be repeated.
7.5.5 Checksum
The user may optionally add a checksum to the end of the command. The checksum is "$" followed by
two hex characters. If a command or a query has checksum, the response will also have one. There is no
CR between the command string and the "$" sign.
Example: STT?$3A
STAT?$7B
7.5.6 Acknowledge
The power supply acknowledges received commands by returning "OK"message. If an error is detected,
the power supply will return an error message. The rules of checksumapply also to the acknowledge.
51
Page 61
7.5.7 Error message
7.7.3 Initialization control commands
ADR is followed by address which can be0to30 and is used to access the
power supply .
Clear status. Sets FEVE and SEVE registers to zero (refer to section 7-8).
Reset command. Brings the power supply toasafe and knownstate:
Output voltage: zero, Remote: non-latched remote,
Output current: zero, Auto-start: Off,
Output: Off, OVP: maximum,
FOLD:Off,UVL: zero
The conditional registers (FLT and STAT) are updated, the other registers are
not changed.
Command
Sets the power supply to local or remote mode:
1. RMT0or RMT LOC, sets the power supply into Local mode.
2. RMT1or RMT REM, sets the unit into remote mode.
3. RMT2or RMT LLO, sets the unit into Local Lockout mode (latched remote mode).
#
Description
1
ADR n
2
CLS
3
RST
4
RMT
Returns the Remote mode setting:
1. "LOC"- The unit is in Local mode.
2. "REM"- The unit is in Remote mode.
3. "LLO"- The unit is in Local Lockout (latched remote) mode.
Returns MD MODE OPTION Status.1indicates installed and0indicates not
installed.
Repeat last command. If \<CR> is received, the power supply will repeat the
last command.
5
6
7
RMT?
MDAV?
\
7.7.5 Output control commands
7.7.4 ID control commands
Command
#
Description
Returns the power supply model identification as an string
Returns the software version as an ASCII string.
Returns the unit serial number.Upto12 characters.
Returns date of last test. Date format: yyyy/mm/dd
ASCII
: LAMBDA, GENX-Y
1
2
3
4
IDN?
REV?
SN?
DATE?
Command
#
Description
Sets the output voltage value in Volts. The range of voltage value is described in
Table7-3. The maximum number of characters is 12. See the following examples
for PV n format: PV 12, PV 012, PV 12.0, PV 012.00, etc...
Reads the output voltage setting. Returns the string "n" where "n" is the exact
string sent in the PVncommand. When in Local mode, returns the PREVIEW
(front panel) settings ina5digits string.
Reads the actual output voltage. Return5digits string.
Example: 60V supply sends 01.150, 15.012, 50.000, etc...
1
PV n
2
PV?
3
MV?
Reads the output current setting. Returns the string "n" where "n" is the exact
string sent in the PCncommand. When in Local mode, returns the
PREVIEW (front panel) settings ina5digits string.
4
PC n
(See Note 1)
5
PC?
Sets the output current value in Amperes. The range of current values is
described in Table 7-4. The maximum number of characters is 12. See the
following examples for PCnformat: PC 10, PC 10.0, PC 010.00, etc...
If an error is detected inacommand or query, the power supply will respond with an error
message. Refer to section 7.6 for details.
7.5.8 Backspace
The backspace character (ASCII 8) clears the last character sent to the power supply.
Error
Code
E01
E02
E04
E06
E07
Description
Returned when program voltage (PV) is programmed above acceptable range.
Example: PV value is above '105% of supply rating'or 'PV above 95% of OVP setting'.
Returned when programming output voltage below UVL setting.
Returned when OVP is programmed below acceptable range.
Example:OVP value is less than '5% of supply voltage rating' plus 'voltage setting'.
Returned when UVL value is programmed above the programmed output voltage.
Returned when programming the Output to ON during a fault shut down.
7.6 ERRORMESSAGES
The power supply will return error messages for illegal commands and illegal programming
parameters. Refer to Table 7-1 for programming error messages and Table 7-2 for commands
error messages.
Table 7-1: Programming error messages
Table 7-2: Commands error messages
Error
Code
7.7 COMMAND SET DESCRIPTION
C01
C02
C03
C04
C05
Description
Illegal command or query
Missing parameter
Illegal parameter
Checksum error
Setting out of range
7.7.1 General guides
1. Any command or argument maybein capital letters or small letters.
2. In commands with an argument, aspace must be between the command and the argument.
3. For any command that setsanumeric value, the value maybeupto12 characters long.
4. Carriage Return: If the CR character (ASCII 13) is received by itself, the power supply will
respond with "OK" and CR.
7.7.2 Command set categories
The Genesys 3300W series command set is divided into four categories as follows:
1. Initialization control
2. ID control
3. Output control
4. Status control
TM
52
Page 62
7.7.3 Initialization control commands
Command
#
1
ADR n
CLS
2
RST
3
4
RMT
RMT?
5
6
MDAV?
\
7
Description
ADR is followed by address which can be0to30 and is used to access the
power supply .
Clear status. Sets FEVE and SEVE registers to zero (refer to section 7-8).
Reset command. Brings the power supply toasafe and knownstate:
Output voltage: zero, Remote: non-latched remote,
Output current: zero, Auto-start: Off,
Output: Off, OVP: maximum,
FOLD:Off,UVL: zero
The conditional registers (FLT and STAT) are updated, the other registers are
not changed.
Sets the power supply to local or remote mode:
1. RMT0or RMT LOC, sets the power supply into Local mode.
2. RMT1or RMT REM, sets the unit into remote mode.
3. RMT2or RMT LLO, sets the unit into Local Lockout mode (latched remote mode).
Returns the Remote mode setting:
1. "LOC"- The unit is in Local mode.
2. "REM"- The unit is in Remote mode.
3. "LLO"- The unit is in Local Lockout (latched remote) mode.
Returns MD MODE OPTION Status.1indicates installed and0indicates not
installed.
Repeat last command. If \<CR> is received, the power supply will repeat the
last command.
7.7.4 ID control commands
Command
#
1
2
3
4
IDN?
REV?
SN?
DATE?
Returns the power supply model identification as an string
Returns the software version as an ASCII string.
Returns the unit serial number.Upto12 characters.
Returns date of last test. Date format: yyyy/mm/dd
7.7.5 Output control commands
#
Command
PV n
1
Sets the output voltage value in Volts. The range of voltage value is described in
Table7-3. The maximum number of characters is 12. See the following examples
for PV n format: PV 12, PV 012, PV 12.0, PV 012.00, etc...
2
PV?
Reads the output voltage setting. Returns the string "n" where "n" is the exact
string sent in the PVncommand. When in Local mode, returns the PREVIEW
(front panel) settings ina5digits string.
MV?
3
Reads the actual output voltage. Return5digits string.
Example: 60V supply sends 01.150, 15.012, 50.000, etc...
4
PC n
(See Note 1)
Sets the output current value in Amperes. The range of current values is
described in Table 7-4. The maximum number of characters is 12. See the
following examples for PCnformat: PC 10, PC 10.0, PC 010.00, etc...
PC?
5
Reads the output current setting. Returns the string "n" where "n" is the exact
string sent in the PCncommand. When in Local mode, returns the
PREVIEW (front panel) settings ina5digits string.
Description
Description
ASCII
: LAMBDA, GENX-Y
53
Page 63
7.7.5 Output control commands-cont
Command
#
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MC?
(See Note 2)
DVC?
OUT n
OUT?
FLD n
FLD?
FBD nn
FBD?
FBDRST
OVP n
OVP?
OVM
UVL n
UVL?
AST n
AST?
SAV
RCL
MODE?
Description
Reads the actual output current. Returns5digits string.
Example: 200A supply sends 000.50, 110.12, 200.00, etc...
Display Voltage and Current data. Data will be returned asastring of ASCII characters. A
comma will separate the different fields. The fields, in order, are: Measured Voltage,
Programmed Voltage, Measured Current, Programmed Current, Over Voltage Set point
and Under Voltage Set Point.
Example: 5.9999, 6.0000, 010.02, 010.00, 7.500, 0.000
Turns the output to ON or OFF. Recover from Safe-Start, OVP or FLD fault.
OUT 1 (or OUT ON)-Turn On.
Returns the output On/Offstatus string.
ON- output on. OFF- output off.
Sets the Foldback protection to ON or OFF.
FLD1(or FOLD ON) - Arms the Foldback protection.
FLD0(or FOLD OFF)- Cancels the Foldback protection.
When the Foldback protection has been activated, OUT 1 command will release the
protection and re-arm it, while FLD0will cancel the protection.
Returns the Foldback protection status string:
“ON”- Foldback is armed, “OFF”- Foldback is canceled.
Add (nnx0.1) seconds to the Fold Back Delay. This delay is in addition to the standard
delay. The range of nn is0to 255. The value is stored in eprom at AC power down and
recovered at AC power up.
Supply returns the value of the added Fold Back Delay.
Reset the added Fold Back Delay to zero.
Sets the OVP level. The OVP setting range is given in Table 7-5. The number of characters
after OVP is up to 12.
The minimum setting level is approx. 105% of the set output voltage, or the value in Table
7-6, whichever is higher. The maximum setting level is shown in Table 5-1. Attempting to
program the OVP below this level will result in execution error response (”E04”). The OVP
setting stays unchanged.
Returns the setting “n” where “n” is the exact string in the user’s “OVP n”. When in Local
mode, returns the last setting from the front panel ina4digit string.
Sets OVP level to the maximum level. Refer to Table 7-5.
Sets Under Voltage Limit. Value of “n” may be equal to PV setting, but returns “E06” if
higher. Refer to Table 7-6 for UVL programming range.
Returns the setting “n” where “n” is the exact string in the user’s “UVL n”. When in Local
mode, returns the last setting from the front panel ina4digit string.
Sets the auto-restart mode to ON or OFF.
AST 1 (or AST ON)- Auto restart on.
AST 0 (or AST OFF)- Auto restart off.
Returns the string auto-restart mode status.
Saves present settings. The settings are the same as power-down last settings.
These settings are erased when the supply power is switched off and the new “last settings”
are saved.
Recalls last settings. Settings are fromthe last power-down or from thelast“SAV”
command.
Returns the power supply operation mode. When the power supply is On (OUT 1) it will
return “CV” or “CC”. When the power supply is OFF (OUT 0) it will return “OFF”.
25
MS?
Returns the Master/Slave setting. Master: n=1,2,3,or4 Slave: n=0
54
Page 64
NOTES:
1. In Advanced parallel mode (refer to Sec. 5.15.2), “n” is the total system current.
2. In Advanced parallel mode, “MC?” returns the Master unit current multiplied by the number of
slave units+1.
7.7.6 Global output commands
1. General
All supplies, even if not the currently addressed supply, receivingaglobal command will execute
the command. No response to the PC issuing the command will be returned to the PC. The PC
issuing the command will be responsible to delay and any other communications until the
command is execute. 200 Ms minimum is the suggested delay.
If the command contains an error, out of range values for example, no error report will be sent to
the issuing PC.
Reset. Brings the Power Supply toasafe and known state:
Output voltage: 0V, output current: 0A, OUT:Off, Remote: RMT 1’
1.
2.
GRST
GPV n
AST:Off OVP:Max, UVL:0.
The conditional register (FLT and STAT) are updated. Other registers are not changed.
Non-Latching faults (FB, OVP, SO) are cleared, OUT fault stays.
Sets the output voltage value in volts. The range of voltage values is shown in Table 7-3.
‘n’ may be up to 12 char plus dec. pt
3.
GPC n
Program the output current value in amperes. The range of current values is shown in
Table 7-4. ‘n’ may be up to 12 char plus dec. pt
Turns the output to ON or OFF:
“OUT 1/ON”=turn on
GOUT
4.
“OUT 0/OFF”= turn off, clears CV and CC bitsin the Status Condition (STAT)
OUT ON will respond with “E07’if the output cannot be turned on because ofalatching
fault (OTP< AC, ENA, SO) shutdown.
Save present settings. Same settings as power-down last settings listed in Error!
5.
GSAV
Reference source not found. Except the address and Baud rate are not saved
Saves to the RAM. These settings are erased when the supply power is switched off and
the new ‘last settings’ are saved.
6.
GRCL
Recall last settings. Settings are from last power-down or from last ‘SAV’ or ‘GSAV’
command. Address and Baud rate are not recalled so communication is not interruped.
Table 7-3: Voltage programming range
Model
Rated Output Voltage(V)
8
10
15
20
30
40
50
60
80
100
150
200
300
600
Minimum
(V)
0.000
00.000
00.000
00.000
00.000
00.000
00.000
00.000
00.00
000.00
000.00
000.00
000.00
000.00
Maximum
(V)
8.000
10.000
15.000
20.000
30.000
40.000
50.000
60.000
80.00
100.00
150.00
200.00
300.00
600.00
NOTE:
The power supply can accept values higher by 5% than
the table values, however it is not recommended to
program the power supply over the rated values.
55
Page 65
Table 7-4:
Model
GEN8-400
GEN10-330
GEN15-220
GEN20-165
GEN30-110
GEN40-85
GEN60-55
GEN80-42
GEN100-33
GEN150-22
GEN200-16.5
GEN300-11
GEN600-5.5
Current programming range
Minimum
(A)
000.00
000.00
000.00
00.00
00.00
00.00
00.000
00.000
00.000
00.000
00.000
0.000
0.000
Maximum
(A)
400.00
330.00
220.00
165.00
110.00
85.00
55.000
42.000
33.000
22.000
16.500
11.000
5.500
NOTE:
The power supply can accept values higher by 5% than the table values, however it
is not recommended to program the power supply over the rated values.
Table 7-5: OVP programming range
Model
RatedOutput Voltage(V)
8
10
15
20
30
40
60
80
100
150
200
300
600
Minimum
(V)
0.5
0.5
1.0
1.0
2.0
2.0.
5.0
5.0
5.0
5.0
5.0
5.0
5.0
Maximum
(V)
10.0
12.0
18.0
24.0
36.0
44.0
66.0
88.0
110
165
220
330
660
7.7.7 Status control commands
Refer to section 7-8 for definition of the registers.
Command
#
1
STT?
Reads the complete power supply status.
Returns ASCII characters representing the following data, separated by commas:
MV<actual (measured) voltage>
PV<programmed (set) voltage>
MC<actual (measured) current>
Example response: MV(45.201),PV(45),MC(4.3257),PC(10),SR(30),FR(00)
FLT?
2
3
4
5
6
7
8
9
FENA
FENA?
FEVE?
STAT?
SENA
SENA?
SEVE?
Reads Fault Conditional Register.Return 2-digit hex.
Set Fault Enable Register using 2-digit hex.
Reads Fault Enable Register.Returns 2-digit hex.
Reads Fault Event Register. Returns 2-digit hex. Clears bitsof Fault Event Register.
Reads Status Conditional Register.Returns 2-digit hex.
SetsStatus Enable Register using 2-digit hex.
Reads Status Enable Register.Returns 2-digit hex.
Reads Status Event register. Returns 2-digit hex. Clears bitsofStatus Event register.
Table 7-6: UVL programming range
Model
Rated Output Voltage(V)
8
10
15
20
30
40
60
80
100
150
200
300
600
Minimum
(V)
0
0
0
0
0
0
0
0
0
0
0
0
0
Maximum
Description
PC<programmed (set) current>
SR<status register, 2-digit hex>
FR<fault register, 2-digit hex>
(V)
7.60
9.50
14.3
19.0
28.5
38.0
57.0
76.0
95.0
142
190
285
570
56
Page 66
7.8 STATUS,ERROR AND SRQREGISTERS
7.8.1 General
This section describes the various status error and SRQ registers structure. The registers can be
read or set via the RS232/485 commands. When using the IEEE option, refer to the user manual
for Genesys Power Supply IEEE Programming interface.
Refer to Fig.7-7 for the Status and Error Registers Diagram.
TM
Constant Voltage
Constant Current
No Fault
Fault
Auto Start
Fold Enabled
Spare
Local Mode
Spare
AC Fail
Over Temperature
Foldback (tripped)
Over Volt Prot
Shut Off (rear panel)
Output Off (front panel)
Enable Open
Command Error (”Cnn”)
Execution Error (”Enn”)
Query Response (”message”)
Command Response (”OK”)
Status Registers
LSB
MSB
Condition
0
CV
1
CC
2
NFLT
3
FLT
4
AST
5
FDE
6
7
LCL
“STAT?”
0
Enable
0
0
0
“SENA xx”
“SENA?”
Fault Registers
Condition
LSB
0
0
1
AC
2
OTP
3
FLD
4
OVP
5
SO
6
MSB
OFF
7
ENA
“FLT?”
Event
CV
CC
NFLT
FLT
0
0
0
LCL
“SEVE?”
OR
Enable
“FENA xx”
“FENA?”
OR
OR
Address
Changed
Event
0
AC
OTP
FLD
OVP
SO
OFF
ENA
“FEVE?”
Response
messages
SRQ
Messages
OR
One response for every command
or query received.
OR
Serial
TXD
SRQ=“!nn”,
nn=address
One SRQ when SEVE goes
from all zeroes to any bit set.
Setting more SEVE bits does
not cause more SRQs.
Positive Logic:
0=No Event
1=Event Occured
Fig.7-7: Status and Error Registers Diagram
7.8.2 Conditional registers
The fault Condition Register and the Status Condition Register are read only registers that the user
may read to see the condition of the supply. Refer to table 7-8 for description of the Fault Condition
Register bits and Table 7-9 for the Status Condition register bits.
57
Page 67
7.8.2 Conditional registers
Table 7-7: Fault Condition Register
BIT
Fault name
Fault symbol
0 (LSB)
AC Fail
1
Over
2
AC
OTP
temperature
3
Foldback
FOLD
Foldback shutdown
has occurred.
4
5
6
Over
voltage
Shut Off
Output Off
OVP
SO
OFF
OVP shutdown has
occurred.
Front panel OUT
button pressed to Off.
7(MSB)
Enable
ENA
Table 7-8: Status Condition Register
BIT
0 (LSB)
Status name
Constant
Status symbol
CV
Voltage
1
Constant
CC
Current
2
3
No Fault
Fault
NFLT
FLT
The power supply is
operating normally or
fault reporting is not
enabled. See “OUT n”
command in Section
7.7.5.
active
4
Auto-
AST
Restart
Enabled
Fold
5
FDE
Enabled
6
Spare bit
SPARE
Bit Set condition
Fixed to zeroSPARESpare bit
AC fail has occurred.
OTP shutdown has
occurred.
Rear panel J "Shut
Off" condition has
occurred.
Rear panel J1 Enable
terminals(J1-1&J1-14)
opened.
Bit Set condition
Output is On and the
supply in CV.
Output is ON and the
supply in CC.
One or more faults are
enabled and occur.
Supply is in AutoRestart mode (from
Front Panel or serial
command).
Fold protection
enabled (from Front
Panel or serial
command).
Fixed to zero.
Bit Reset condition
Fixed to zero
The AC input returns to normal.
The power supply cools down.
The supply output is turned On by
front panel button or OUT 1
command.
The supply output is turned On by
front panel button or OUT 1
command.
Rear panel J1 "Shut Off" condition
removed.
The supply output is turned On by
front panel button or OUT 1
command.
Rear panel J1 Enable terminals closed.
Bit Reset condition
Output is ON and the supply is not in
CV.
Output is ON and the supply is not in
CC.
One or more faults are active and
fault reporting is enabled (using
“FENA xx”).
Fault Event Register cleared (FEVE?).
Supply is in Safe-Start mode (from
Front Panel or serial command).
Fold protection disabled (from Front
Panel or serial command).
Fixed to zero.
7 (MSB)
Local Mode
LCL
Supply in Local mode.
Supply in Remote mode or LocalLockout mode.
7.8.3 Service Request: Enable and Event Registers
The conditional Registers are continuously monitored. When a change is detected in a register bit
which is enabled, the power supply will generate an SRQ message.
The SRQ message is: "!nn" terminated by CR, where the nn is the power supply address.
The SRQ will be generated either in Local or Remote mode.
Refer to Tables 7-9 to 7-12 for details of the Enable and Event registers.
58
Page 68
1.Fault Enable Register
The Fault Enable Register is set to the enable faults SRQs.
Table 7-9: Fault Enable Register
BIT
0 (LSB)
1
2
3
4
5
6
7(MSB)
2.Fault Event Register
The Fault Event will set a bit if a condition occurs and it is enabled. The register is cleared when
FEVE?, CLS or RST commands are received.
Table 7-10: Fault Event Register
Enable
bit name
Spare bit
AC Fail
Over Temperature
Foldback
Over Voltage
Shut Off
Output Off
Enable
Fault symbol
SPARE
AC
OTP
FOLD
OVP
SO
OFF
ENA
Bit Set condition
User command:
"FENA nn" where
nn is hexadecimal
Bit reset condition
User command: "FENA nn"
where nn is hexadecimal (if
nn="00", no fault SRQs will
be generated).
BIT
0 (LSB)
1
2
3
4
5
6
7(MSB)
Event
bit name
Spare bit
AC Fail
Over Temperature
Foldback
Over Voltage
Shut Off
Output Off
Enable
Fault symbol
SPARE
AC
OTP
FOLD
OVP
SO
OFF
ENA
Bit Set condition
Fault condition
occurs and it is
enabled.
The fault can set
a bit, but when
the fault clears
the bit remains
set.
Bit reset condition
Entire Event Register is
cleared when user sends
"FEVE?" command to read
the register.
"CLS" and power-up also
clear the Fault Event
Register. (The Fault Event
Register is not cleared by
RST)
59
Page 69
3.Status Enable register
The Status Enable Register is set by the user to enable SRQs from changes in power supply
status.
Table 7-11: Status Enable Register
BIT
0 (LSB)
1
2
3
4
5
6
7(MSB)
4.Status Event Register
The Status Event Register will setabit ifachange in the power supply status occurs and it is
enabled. The register is cleared when the "SEVE?" or "CLS" commands are received. A change
in this register will generate SRQ.
Table 7-12: Status Event Register
Status name
Constant Voltage
Constant Current
No Fault
Fault active
Auto-Restart enabled
Fold enabled
Spare
Local Mode
Status symbol
CV
CC
NFLT
FLT
AST
FDE
Spare
LCL
Bit Set condition
User command:
"SENA nn" is
received,
where nn is
hexadecimal bits.
Always zero
Always zero
Always zero
"SENA nn"
command
Bit reset condition
User command: "SENA nn"
is received, where nn is
hexadecimal bits.
If "nn"=00, no SRQis sent
when there isachange in
Status Condition Register.
Always zero
Always zero
Always zero
"SENA nn"
command
BIT
0 (LSB)
1
2
3
4
5
6
7(MSB)
Status
name
Constant Voltage
Constant Current
No Fault
Fault active
Not used
Not used
Not used
Local Mode
Status
symbol
CV
CC
NFLT
FLT
0
0
0
LCL
Bit Set condition
Changes in status
occurs and it is
enabled.
The change can
set a bit, but when
the change clears
the bit remains
set.
Always zero
Always zero
Always zero
Unit is set to Local
by pressing front
panel REM/LOC
button.
Bit reset condition
Entire Event Register is
cleared when user sends
"SEVE?" command to read
the register.
"CLS" and power-up also
clear the Status Event
Register. (The Fault Event
Register is not cleared by
RST)
60
Page 70
7.9 SERIAL COMMUNICATION TEST SET-UP
Use the following instructions as basic set-up to test the serial communication operation.
1.Equipment:
PC with Windows Hyper Terminal, private edition, software installed, Genesys
power supply, RS232 cable.
TM
2.PC set-up:
2.1 Open Hyper Terminal.......................New Connection.
2.2 Enter a name
2.3 Connect to.......................................Direct to Com1 or Com2
2.4 Configure port properties:
2.5 Open Properties in the program File...........................Properties
2.6 Setting: ASCII Set Up
3.Power supply set-up:
3.1 Connect the power supply to the PC using the RS232 cable.
3.2 Set via the front panel: Baud Rate: 9600, Address: 06.
3.3 Set via the rear panel: RS232/485 to RS232 (refer to section: 4-4).
Bits per second .......9600
Data bits ..................8
Parity .......................None
Stop bits....................1
Flow control..............None
Select Echo characters locally, select send line ends with line feed.
On somePC systems, pressing the number keypad "Enter" will
distort displayed messages. Use the alphabetic "Enter" instead.
4.Communication Test:
4.1 Model identification:
PC:write: ADR06
Power supply response: "OK"
4.2 Command test:
PC write: OUT 1
Power supply response: "OK"
PC write: PV n
Power supply response: "OK"
PC write: PC n (for n values see Tables 7-3, 7-4 and 7-5)
Power supply response: "OK"
The power supply should turn on and the display will indicate the output voltage
and the actual output current.
61
Page 71
CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION
8.1 INTRODUCTION
Isolated Analog Programming is an internal option card for analog programming of the Genesys
power supply series. The option is factory installed and cannot be obtained with GPIB (IEEE)
Interface. Output Voltage and Current Limit can be programmed and readback through optically
isolated signals which are isolated from all other ground references in the power supply.
There are two types of Isolated Analog programming cards:
1. 0-5V/0-10V option (PN: IS510): Using 0-5V or 0-10V signals for programming and readback.
2. 4-20mA option (PN: IS420): Using current signals for programming and readback.
8.2 SPECIFICATIONS
8.2.1 0-5V/0-10V option (PN: IS510)
TM
Programming
Inputs
Monitoring
Outputs
Output voltage programming accuracy
Output current programming accuracy
Output voltage programming temperature coefficient
Output current programming temperature coefficient
Input impedance
Absolute maximum voltage
Max. voltage between program inputs and supply outputs
Output voltage monitoring accuracy
Output current monitoring accuracy
Output Impedance (see note)
Max. voltage between monitoring outputs and supply outputs
%
%
o
PPM/ C
o
PPM/ C
Ohm
Vdc
Vdc
%
%
Ohm
Vdc
+/-1
+/-1
+/-100
+/-100
1M
0-15
600
+/-1.5
+/-1.5
100
600
NOTE:
Use 100Kohm minimum input impedance for the monitoring circuitsto minimize the readback error.
8.2.2 4-20mA option (PN: IS420)
Programming
Inputs
Monitoring
Outputs
Output voltage programming accuracy
Output current programming accuracy
Output voltage programming temperature coefficient
Output current programming temperature coefficient
Input impedance
Absolute maximum input current
Max. voltage between program inputs and supply outputs
Output voltage monitoring accuracy
Output current monitoring accuracy
Maximum load impedance
Max. voltage between monitoring outputs and supply outputs
%
%
o
PPM/ C
o
PPM/ C
Ohm
mA
Vdc
%
%
Ohm
Vdc
+/-1
+/-1
+/-200
+/-200
50
0-30
600
+/-1.5
+/-1.5
500
600
62
Page 72
8.3ISOLATED PROGRAMMING&MONITORING CONNECTOR
Refer to Table8-1 for detailed descriptionofthe rear panel IsolatedProgramming&Monitoring
connector. To providethe lowest noise performance, it is recommended to useshielded-twisted
pair wiring.
Refer to Fig.8-1for descriptionofthe connector.
Isolated programming plug P/N: MC1.5/8-ST-3.81, Phoenix.
+VPROG_ISO
+IPROG_ISO
GND
Shield
1
3
2
4
6
5
8
7
Shield
+IMON_ISO
+VMON_ISO
GND
Fig.8-1: Isolated Programming&Monitoring connector
Table8-1: Detailed descriptionofIsolated programming&Monitoring connector
Terminal
1
Signal name
SHLD
Function
Shield, connected internally to
Range 0-5/0-10V
IS510 option
Chassisground
chassisofthe supply.
2
3
4
+VPROG_ISO
+IPROG_ISO
GND
Output voltage programming input
Output current programming input
Ground forprogramming
signals.
0-5/0-10V
0-5/0-10V
Ground
Range 4-20mA
IS420 option
4-20mA
4-20mA
Ground
5
6
7
8
GND
+VMON_ISO
+IMON_ISO
SHLD
Ground forprogramming
signals.
Output voltage monitoring output
Output current monitoring output
Shield, connected internally to
Ground
0-5/0-10V
0-5/0-10V
Chassisground
Ground
4-20mA
4-20mA
chassisofthe supply.
CAUTION
When the IsolatedAnalog Optionisinstalled, do notapply any signalstothe
non-isolated VPGM and IPGM (J1-9 and J1-10) pins. All other J1 features
may be used normally. Refer toSection4.5 foradescriptionofJ1features.
Parallel Operation: Optional Isolated Analog IS510 / IS420 must be
installed in both the Master and Slave unit.
63
Page 73
8.4 SETUP AND OPERATINGINSTRUCTIONS
CAUTION
To prevent damage to the unit, do not program the output voltage and current
to higher then the power supply rating.
8.4.1 Setting up the power supply for 0-5/0-10V Isolated Programming and Monitoring
Perform the following procedure to configure the power supply:
1. Turn the power supply AC power switch to Off.
2. Connect a short between J1-8 and J1-12 (refer to Table 4-4).
3. Set Setup switch SW1-1 to itsUP position for Output Voltage external programming
and SW1-2 to itsUP position for Output Current limit external programming.
4. Set SW1 position 3to select the programming voltagerange: Down=0-5V,Up=0-10V.
5. Set SW1 position 4to select the monitoring range: Down=0-5V,Up=0-10V.
6. Ensure that SW1 positions 7 and 8 are in the their down position.
7. Connect the programming sources to the mating plug of the Isolated Programming
connector.Observe for correct polarity of the voltage source.
NOTE
J1-8 and J1-12 must be shorted together withajumper.
8. Set the programming sources to the desired levels and turn the power supply ON.
8.4.2 Setting up the power supply for 4-20mA Isolated Programming and Monitoring
Perform the following procedure to configure the power supply:
1. Turn the power supplyAC power switch to Off.
2. Connect a short between J1-8 and J1-12 (refer toTable 4-4).
3.Set setup switch SW1-1 to itsUP position for Output Voltage external programming and
SW1-2 to itsUP position for Output Current limit external programming.
4. Set SW1 position 3to it's Up position.
5. Set SW1 position 4to it's Up position.
6. Ensure that SW1 positions 7 and 8 are in their Down position.
7. Connect the programming source to the mating plug of the Isolated Programming
connector.Observe for correct polarity of the voltage source.
NOTE
J1-8 and J1-12 must be shorted together withajumper.
8. Set the programming sources to the desired levels and turn the power supply ON.
NOTE
SW1 position 3 and 4must be in their Up position for operation
with 4-20mA Isolated Programming and Monitoring.
64
Page 74
8.5 PARALLEL OPERATION WITH ISOLATED ANALOG OPTION
CAUTION
To prevent damage to the unit, do not program
the output voltage and current to higher then the
power supply rating
Um das Gerät vor Schäden zu schützen, programmieren
Sie keine Spannungs-oder Stromwerte, die über den
maximalen Nennwerten liegen.
VORSICHT
Power supplies, should be connected in a daisy-chain configuration
8.5.1 Setting Up The Master Unit
Setting up the power supply for 0-5/0-10V Isolated Programming and Monitoring.
Perform the following procedure to configure the power supply:
1. Turn the power supply AC power switch to Off.
2. Connect a short between J1-8 and J1-12 (refer to Table 4-4).
3. Set Setup switch SW1-1 to its UP position for Output Voltage external programming
and SW1-2 to its UP position for Output Current limit external programming.
4. Set SW1 position 3 to select the programming voltage range: Down=0-5V, Up=0-10V.
5. Set SW1 position 4 to select the monitoring range: Down=0-5V, Up=0-10V.
6. Ensure thatSW1positions 7 and 8 are in the their down position.
7. Connect the programming sources to the mating plug of the Isolated Programming connector.
Observe for correct polarity of the voltage source.
8.5.2 Setting Up The Slave Unit
Setting up the power supply for 0-5/0-10V Isolated Programming and Monitoring.
Perform the following procedure to configure the power supply:
1. Turn the power supply AC power switch to Off.
2. Connect a short between J1-8 and J1-12 (refer to Table 4-4).
3. Set Setup switch SW1-1 to its DOWN position for Output Voltage programming by front panel
and SW1-2 to its UP position for Output Current limit external programming.
4. Set SW1 position 3 to select the programming voltage range: Down=0-5V, Up=0-10V.
5. Set SW1 position 4 to select the monitoring range: Down=0-5V, Up=0-10V.
6. Ensure that SW1 positions 7 and 8 are in the their down position.
7. Connect pin 7 (IMON_ISO) of Isolated Analog connector in Master Unit
To pin 3 (IPROG_ISO) of Isolated Analog connector in Slave unit.
8. Connect pin 4 (GND) of Isolated Analog connector in Master Unit
To pin 4 (GND) of Isolated Analog connector in Slave unit.
Daisy-Chain Connection:
9. Connect J1-2,3 of the Master unit to J1-2,3 of
the Slave unit.
10. Connect J1-15 of the Master unit to J1-16 of
the Slave unit.
11. Connect J1-16 of the Master unit to J1-15 of
the Slave unit.
12. Set the programming sources to the desired
levels
and turn the Master and Slave units ON.
+V +V-V -V
MASTER
POWER SUPPLY
DIP switch
SW1:1,3, 4 up
SW1:2,7, 8 down
Isolated Analog
IS510
1
2 3 4 5 6 7 8
VPROG_ISO
GND
GND GND
Customer Voltage Source
0-10V
J1
J1-8
J1-12
IF_COM
J1-2,3
SO
J1-15
PS_OK
J1-16
IMON_ISO IPROG_ISO
+V -V
LOAD
Fig.8-2: Parallel connection
with Isolated Analog ISO510, 0-10V
J1
J1-8
SLAVE
J1-12
IF_COM
SO
PS_OK
POWER SUPPLY
J1-2,3
DIP switch
SW1:2,3, 4 up
SW1:1,7, 8 down
J1-15
J1-16
Isolated Analog
1 2 3 4 5 6 7 8
65
IS510
Page 75
CHAPTER 9 MAINTENANCE
Check if the positive or
negative load wire is loose.
Output is present momentarily
but shutsoff quickly. the display
indicates "OUP".
SYMPTOM
CHECK
ACTION
REF.
3.9.6
3.9.8
Is the power supply
configured to Remote
sense?
Output voltage will not adjust.
Front panel CC LED is on.
Is the unit in constant current
mode?
Check current limit setting
and load current.
5.2.1
5.2.2
Output voltage will not adjust.
Front panel CV LED is on.
Check if output voltage is
adjusted above OVP setting
or below UVL setting.
Set OVP or UVL so they
will not limit the output.
Output current will not adjust.
Front panel CV LED is on.
Is the unit in constant voltage
mode?
Check current limit and
voltage setting.
5.3
5.4
5.2
Check load and sense
wires connection for noise
and impedance effects.
Minimize the drop on the
load wires.
Turn off the AC power
switch. Check load
connections. If analog
programming is used,
check if the OVPis set
lower than the output.
Check rear panel J1
ENABLE connection.
Setup switch SW1 setting.
Check rear panel J1
Output Shut-Off connection.
Check if air intake or
exhaust are blocked.
Check if the unit is
installed adjacent to heat
generating equipment.
Check Foldback setting
and load current.
Connect the sense wires
according to User's
manual instructions.
Turn Off the AC power
and wait until the display
turns off. Turn on the AC
power and press front
panel REM/LOC button.
9.7 FUSE RATING
There are no user replaceable fuses in the power supply. Internal fuses are sized for fault
protection and ifafuse was opened it would indicate that service is required. Fuse replacement
should be made by qualified technical personnel. Refer to Table 9-2 foralisting of the fuses.
Table 9-2: Internal fuses
Is the power supply in remote
sense?
Is the voltage drop on the
load wire high?
Display indicates "ENA"
Display indicates "SO"
Over Voltage Protection
circuit is tripped.
Display indicates "O7P"
Display indicates "Fb"
Are sensing wires
connected properly?
Is the power supply in
Local-Lockout mode?
3.9.4
3.9.8
5.3
5.8
4.4
5.7
5.5
5.12
3.9.8
7.2.5
The front panel controls are
nonfunctional.
Poor
Load regulation
Front panel CV LED is on.
No output. Front panel ALARM
LED is blinking.
No output. Display indicates
"OUP"
Large ripple present in output.
Fuse designation
1-Phase, 190-240Vac
3-Phase, 190-240Vac
3-Phase, 380-415Vac
INPUT FUSE
F301, F302:
30A, 600VAC, Fast Acting
F321, F322, F323:
20A, 600VAC, Fast-Acting
F651,F652, F653:
12A, 600VAC, Fast-Acting
F401, F402
F501, F601
5A, 400VDC, Normal-Blow
20A, 400VDC
9.1 INTRODUCTION
This chapter provides information about maintenance, calibration and troubleshooting.
9.2 UNITS UNDER WARRANTY
Units requiring repair during the warranty period should be returned toaLambda authorized service
facility. Refer to the addresses listing on the back cover of this manual. Unauthorized repairs
performed by other than the authorized service facilities may void the warranty.
9.3 PERIODIC MAINTENANCE
No routine maintenance of the power supply is required except for periodic cleaning. To clean,
disconnect the unit from the AC supply and allow 30sec. for discharging internal voltage. The front
panel and the metal surfaces should be cleaned using mild solution of detergent and water. The
solution should be applied onto a soft cloth, and not directly to the surface of the unit. Do not use
aromatic hydrocarbons or chlorinated solvents for cleaning. Use low pressure compressed air to
blow dust from the unit.
9.4 ADJUSTMENTS AND CALIBRATION
No internal adjustment or calibration is required. There is NO REASON to open the power supply
cover.
9.5 PARTSREPLACEMENT AND REPAIRS
As repairs are made only by the manufacturer or by authorized service facilities, no parts
replacement information is provided in the manual. In case of failure, unusual or erratic operation of
the unit, contact a Lambda sales or service facility nearest you. Please refer to the Lambda sales
offices addresses listing on the back cover of this user manual.
9.6 TROUBLESHOOTING
If the power supply appears to operating improperly, use the troubleshooting guide to determine
whether the power supply, load or external control circuit are the cause.
Configure the power supply for basic front panel operation and perform the testsof section 3.8 to
determine if the problem is with the supply.
Table 9-1 provides the basic checks that can be performed to diagnose problems, and references to
sections of this manual for further information.
Table 9-1: Troubleshooting guide
SYMPTOM
No output. All displays and
indicators are blank.
Is the AC power cord
defective?
CHECK
Is the AC input voltage
within range?
Output is present momentarily
but shutsoff quickly.The display
indicates "AC".
Does the AC source voltage
sag when load is applied?
Check continuity, replace
if necessary.
Check input AC voltage.
Connect
voltage source.
ACTION
to appropriate
Check input AC voltage.
Connect to appropriate
voltage source.
REF.
3.7
3.6
3.7
3.6
66
Page 76
SYMPTOM
Output is present momentarily
but shutsoff quickly. the display
indicates "OUP".
Output voltage will not adjust.
Front panel CC LED is on.
Output voltage will not adjust.
Front panel CV LED is on.
Output current will not adjust.
Front panel CV LED is on.
Large ripple present in output.
No output. Display indicates
"OUP"
No output. Front panel ALARM
LED is blinking.
Poor Load regulation
Front panel CV LED is on.
The front panel controls are
nonfunctional.
CHECK
Is the power supply
configured to Remote
sense?
Is the unit in constant current
mode?
Check if output voltage is
adjusted above OVP setting
or below UVL setting.
Is the unit in constant voltage
mode?
Is the power supply in remote
sense?
Is the voltage drop on the
load wire high?
Over Voltage Protection
circuit is tripped.
Display indicates "ENA"
Display indicates "SO"
Display indicates "O7P"
Display indicates "Fb"
Are sensing wires
connected properly?
Is the power supply in
Local-Lockout mode?
ACTION
Check if the positive or
negative load wire is loose.
Check current limit setting
and load current.
Set OVP or UVL so they
will not limit the output.
Check current limit and
voltage setting.
Check load and sense
wires connection for noise
and impedance effects.
Minimize the drop on the
load wires.
Turn off the AC power
switch. Check load
connections. If analog
programming is used,
check if the OVPis set
lower than the output.
Check rear panel J1
ENABLE connection.
Setup switch SW1 setting.
Check rear panel J1
Output Shut-Off connection.
Check if air intake or
exhaust are blocked.
Check if the unit is
installed adjacent to heat
generating equipment.
Check Foldback setting
and load current.
Connect the sense wires
according to User's
manual instructions.
Turn Off the AC power
and wait until the display
turns off. Turn on the AC
power and press front
panel REM/LOC button.
REF.
3.9.6
3.9.8
5.2.1
5.2.2
5.3
5.4
5.2
3.9.4
3.9.8
5.3
5.8
4.4
5.7
5.12
5.5
3.9.8
7.2.5
9.7 FUSE RATING
There are no user replaceable fuses in the power supply. Internal fuses are sized for fault
protection and ifafuse was opened it would indicate that service is required. Fuse replacement
should be made by qualified technical personnel. Refer to Table 9-2 foralisting of the fuses.
Table 9-2: Internal fuses
Fuse designation
INPUT FUSE
F401, F402
F501, F601
1-Phase, 190-240Vac
F301, F302:
30A, 600VAC, Fast Acting
3-Phase, 190-240Vac
F321, F322, F323:
20A, 600VAC, Fast-Acting
5A, 400VDC, Normal-Blow
20A, 400VDC
3-Phase, 380-415Vac
F651,F652, F653:
12A, 600VAC, Fast-Acting
67
Page 77
USER MANUAL INDEX
SW1
30, 31
A
ac cables
ac fail
accessories
acknowledge
address
adjustment
auto-restart
B
back space
baud rate
bipolar voltage
C
calibration
configuration
checksum
communication
constant current
constant voltage
cooling
cv indicator
cc indicator
D
daisy-chain
display
E
enable
error message
external resistor
external voltage
F
fine
foldback
fuse
front panel control
front panel locking
G
grounding
global output command 55
H
humidity
hyper terminal
8, 15
29
8
51
18, 48
66
38
52
18, 48
40
66
48
51
51, 61
17, 34
17, 34
8, 10
27, 37
27, 37
43, 51
27
33
52
46
45
29
18, 36
67
27
43
24
10
61
I
ID control
initialization
installation
isolated
J
J1
J2
J3
L
last setting memory
linking power supplies
line feed
local operation
local sensing
lock front panel
M
maintenance
Master/Slave
MD
O
otp
outline
over voltage
P
parallel operation
parity
ps_ok
preview
R
rack mounting
rear panel
remote sensing
remote/local
registers structure
RS232
RS485
RXD
RX(RS232)
S
safe start
safety
series operation
shield
specifications
status control
SRQ
shut-off
52
53
13
62
32, 45, 46
16, 25
49
28, 38
51
51
34
25
43
66
41
51
38
12
27,35
41
61
37, 43
28
13
29
26
28
57
48, 49, 50
48, 49, 50
49, 50
49, 50
38
3
38
49
9, 62
56, 57
57
36
T
TXD
TX(RS232)
U
under voltage limit
V
volts display
W
warranty
wire size
49, 50
49, 50
17, 36
27
1, 66
19
68
Page 78
NOTES
69
Page 79
NOTES
70
Page 80
NOTES
71
Page 81
NOTES
72
Page 82
NORTH AMERICA
TDK-Lambda Americas Inc
405 Essex Rd. Neptune, NJ 07753
Tel: +1-732-922-9300 Fax: +1-732-922-1441
E-mail: sales@us.tdk-lambda.com
www.us.tdk-lambda.com/hp
UK
TDK-Lambda UK Ltd.
Kingsley Avenue Ilfracombe, Devon
EX 34 8ES United Kingdom
Tel: +44-1271-856666 Fax: +44-1271-864894
E-mail: powersolutions@uk.tdk-lambda.com
www.uk.tdk-lambda.com
FRANCE
TDK-Lambda France SAS
ZAC des Delaches
BP 1077 - Gometz le Chatel
91940 LES ULIS
Tel: +33 1 60 12 71 65
Fax: +33 1 60 12 71 66
E-mail: france@fr.tdk-lambda.com
www.fr.tdk-lambda.com
GERMANY
TDK-Lambda Germany GmbH
Karl-Bold-Str.40,
D-77855 Achern, Germany
Tel: +49-7841-666-0 Fax: +49-7841-500-0
E-mail: info.germany@de.tdk-lambda.com
www.de.tdk-lambda.com
AUSTRIA
TDK-Lambda Austria Sales Office
Aredstrasse 22,
A - 2544 Leobersdorf, Austria
Tel: +43-2256-65584 Fax: +43-2256-64512
E-mail: info.germany@de.tdk-lambda.com
www.de.tdk-lambda.com
ITALY
TDK-Lambda Italy Sales Office
France Sas Succursale Italiana
Via dei Lavoratori 128/130
IT 20092 Cinisello Balsamo, Milano, Italy
Tel: +39-02-6129-3863 Fax: +39-02-6129-0900
E-mail: info.italia@it.tdk-lambda.com
www.it.tdk-lambda.com
ISRAEL
TDK-Lambda Ltd.
Sales Office: Kibbutz Givat Hashlosha Tel-Aviv 4880000, Israel
Tel: +972-3-9024-333 Fax: +972-3-9024-777
Plant: 56 Haharoshet St.,
Karmiel Industrial Zone 2165158, Israel
Tel: +972-4-9887-491 Fax: +972- 4-9583-071
www.tdk-lambda.co.il E-mail: info@tdk-lambda.co.il
JAPAN
TDK-Lambda Corporation
International Sales Divison
Nittetsu Bldg. 6F, 1-13-1 Nihonbashi, Chuo-ku, Tokyo 103-0027, Japan
Tel: +81-3-5201-7175
Fax: +81-3-5201-7287
www.tdk-lambda.com
CHINA
Shanghai Branch of Wuxi TDK-Lambda Electronic Co. Ltd.
28F, Xingyuan Technology Building No.418, Guiping Road,
Shanghai, China 200233
Tel: +86-21-6485-0777 Fax: +86-21-6485-0666
www. cn.tdk-lambda.com
Beijing Branch of Wuxi TDK-Lambda Electronic Co. Ltd.
Room 12B11-12B12, Unit 7 DACHENG SQUARE, No.28
Xuanwumenxi Street, Xuanwu District Beijing, 100053, CHINA
Tel: +86-10-6310-4872 Fax: +86-10-6310-4874
www. cn.tdk-lambda.com
Shenzhen Branch of Wuxi TDK-Lambda Electronics Co.Ltd.
Room 4302, Excellence Times Square Building,
4068 Yi Tian Road, Futian District,
Shenzhen, China 518048
Tel: +86 -755-83588261 Fax: +86 -755-83588260
www. cn.tdk-lambda.com
KOREA
TDK-Lambda Corporation Seoul Office
8F Songnam Bldg, 1358-6, Seocho-Dong,
Seocho-Gu, Seoul, 137-862 KOREA
Tel: +82-2-3473-7051
Fax: +82-2-3472-9137
www.tdk-lambda.co.kr
SINGAPORE
TDK-Lambda Singapore Pte.Ltd.
Blk 1008 Toa Payoh North # 07-01/03
Singapore 318996
Tel: +65-6251-7211
Fax: +65-6250-9171
www.tdk-lambda.com.sg
INDIA
TDK - LAMBDA Singapore Pte Ltd (India Branch)
No.989, 1st Cross, 2nd Floor, 13th Main,
HAL 2nd Stage, Bangalore, Karnataka, India – 560 008
Tel: +91-80-43550 500
Fax: +91-80-43550 501
www.tdk-lambda.com.sg
MALAYSIA
TDK-Lambda Malaysia Sdn. Bhd.
c/o TDK (Malaysia) Sdn Bhd
Lot 709, Nilai Industrial Estate 71800 Nilai
Negeri Sembilan, Malaysia
Tel: + 60 6-799 1130
Fax: + 60 6 799 3277
www.tdk-lambda.com.my
Innovating Reliable Power
TDK-Lambda EMEA
www.emea.tdk-lambda.com
IA626-04-01 Rev. Q
AD0814
Loading...