
To drive with an Iritrack - security system and satellite tracking - you need a fitting kit for bike/quad including the
power cable and the antenna cables + GPS and Iridium antenna.
The bracket has to be ordered separately: you can install your Iritrack on your bike or quad with several types of
brackets:
KIT COMPOSITION:
1 : Power cable 3 m
2 : Iridium octagonal antenna on a
plate, with a 10 cm cable
3 : Iridium antenna cable 1 m
4 : GPS rectangular antenna on a
plate, with a 10 cm cable
5 : GPS antenna cable 1 m
6 : Shrinkable tube, protect cables,
3 amp fuse.
Bracket to order separately:
Touratech 6-points bracket for Iritrack + GPS on the handlebar Réf. SUPG203+ SUPC204 - ERTF
Touratech 6-points bracket for Iritrack
Please contact ERTF, competition@ertf.com
Whole assembly with GPS / Iritrack :
SUPG 203 - Touratech 6-points bracket for Iritrack
SUPC 204 - Omega module for GPS
Separate IRITRACK bracket on the navigation column Réf. PR4005 - TDCOM
Iritrack assembly with a separate Iritrack bracket
on the navigation column
• The separate Iritrack bracket can be mounted
- horizontally (keyboard upwards) or
- vertically (keyboard towards the driver)
The keyboard must be accessible and visible for handling in case of
emergency.
• The bracket must absolutely be fitted with a damping system
Technical characteristics of the Iritrack :
- Dimensions of the V2/V2.5 without bracket: 175 mm x 125 mm x 48 mm (without plugs and cables)
- Weight of the box Iritrack: about 1.0 Kg
- Environment: Operating from - 30 ° C to + 55 ° C and storage from -40 ° C to +65 ° C
- Consumption under 12V for Iritrack, 100mA on rest, 1000mA on communications
ASSEMBLY INSTRUCTIONS
IRITRACK KIT - BIKE/QUAD
The machine must be presented at the technical
verifications with the bracket, cabling and
antennas mounted, ready to receive the Iritrack
- DEPARTEMENT RALLYE RAID
– 114/126 Avenue d’Alfortville
TEL : + 33 (0)1 48 84 34 00 – FAX : + 33 (0) 1 48 52 53 54 – email: rallye@tdcom.fr – www.tdcom.com
Sa au capital de 236 400 € - SIRET 334 306 172 00035 – RC 334 306 172 – code APE 5912 Z

BRACKET
• The bracket can be mounted on the dashboard. The
buttons on the Iritrack must be visible and accessible
by the pilot in case of emergency
• It is essential to have sufficient space in order to
move fingers at the back of the box to check the
connection of the cables: about 10cm.
Iritrack assembly with separate Iritrack bracket:
The separate Iritrack bracket must absolutely be fitted with a damping system
(silent-blocs available on request, réf PR4057 TDCOM).
If there is no damping system, a non-compliance will be declared during the technical verifications.
EXTENSION OF POWER
Connect the red wire on the +12 V / +24 V (red terminal) and the black wire to the negative pole of the battery
Install the 3A fuse on the red wire.
L’Iritrack must be connected directly to the battery, as required by the FIM rules (no breaker and no contact
on power).
Bring power to the bracket
GPS IRITRACK & IRIDIUM ANTENNAS AND CABLES
The antenna must be installed in front of the bike / quad
(middle of the front fender, the top of the bubble or the head of instrumentation).
It is strongly advised to place plastic collars (type Rislan) to maintain the antennas
GPS and Iridium antennas can be side by side. They must be installed horizontally and clear of all obstacles at
180 degrees towards the sky. It is forbidden to paint them. Screw the cables from each antenna and bring the
connections to the bracket.
At this stage of the installation you must have at the back of the
support with a margin of 10 cm :
1. Power cable
2. Iridium antenna cable
3. GPS antenna cable
Treat your cable ducts.
• Avoid friction locations.
• It is recommended each day to check the fixings, the wear of
the cables and to tight the connectors
- DEPARTEMENT RALLYE RAID
– 114/126 Avenue d’Alfortville
TEL : + 33 (0)1 48 84 34 00 – FAX : + 33 (0) 1 48 52 53 54 – email: rallye@tdcom.fr – www.tdcom.com
Sa au capital de 236 400 € - SIRET 334 306 172 00035 – RC 334 306 172 – code APE 5912 Z
: It is very important to
put a shrinkable tube on each
antenna / cable to couple them.
Before heating the shrinkable tube,
make sure the connectors are
properly locked.