T&D TR-50U2 User Manual

Communication Port

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com [phone]

TR-50U2

User's Manual

© Copyright T&D Corporation. All rights reserved.

2012.02 16504840002 1st Edition

Table of Contents

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com [phone]

Safety Precautions and Instructions -------------------------------------------4

Before Using this Product ---------------------------------------------------------7

What is Communication Port TR-50U2 ? -------------------------------------8

Using Optical Communication with a Data Logger ----------------------- 10

Specifications ---------------------------------------------------------------------- 11

1

Notices about this User's Manual

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com [phone]

In order to properly use this product, please carefully read this manual
before using. T&D Corporation accepts no responsibility for any
malfunction of and/or trouble with this product or with your computer that
is caused by the improper handling of this product and will deem such
trouble or malfunction as falling outside the conditions for free repair
outlined in the attached warranty.

- All rights of this manual belong to T&D Corporation. It is prohibited to use,
duplicate and/or arrange a part or whole of this User’s Manual without the
permission of T&D Corporation.

®

- Microsoft
Corporation USA and are binding in the USA, Japan and all other
countries.

- Windows Vista is either a registered trademark or trademark of Microsoft
Corporation in the United States, Japan, and/or other countries.

- All registered trademarks, company names, product names and logos
mentioned herein or for products being used are the property of T&D
Corporation or of their respective owners.

- Specifications, design and other contents outlined in this manual are
subject to change without notice.

- Please follow the safety precautions outlined in the Manual carefully. We
cannot guarantee nor are we responsible for safety if this product is used
in any manner other than was intended.

- On-screen messages in this document may vary slightly from the actual
messages.

- Please notify the shop where you purchased this product or T&D
Corporation of any mistakes, errors or unclear explanations in this manual.
T&D Corporation accepts no responsibility for any damage or loss of
income caused by the use of our product.

- This product has been designed for private and/or industrial use only. It is
not for use in situations where strict safety precautions are necessary such
as in connection with medical equipment, whether directly or indirectly.

- We are not responsible for any malfunction or trouble caused by the use of
our product or by any problem caused by the use of measurement results
of our product.
Please be fully aware of this before using our product.

- This manual cannot be reissued, so please keep it in a safe place.

- Please read the warranty and provisions for free repair carefully.

and Windows® are registered trademarks of Microsoft

2

Compliance Information

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com [phone]

Radio, EMC and Safety Regulations

This device complies with Part 15 of the Federal Communications Commission
(FCC) rules. Operation is subject to the following two conditions: (1)This device
may not cause harmful interference, and (2)this device must accept any
interference received, including interference that may cause undesired operation.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

To comply with the limits for the Class B digital device, pursuant to Part 15 of the
FCC Rules, this device must be installed in computer equipment certified to
comply with the Class B limits.

All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables may
result in interference to radio or television reception.

Caution:

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

3