LED DOWNLIGHT RETROFIT KIT QUICK START INSTALLATION GUIDE
For MODELS LED12DR627K, LED14DR627K, LED12DR630K and LED14DR630K
WARNING! RISK OF ELECTRIC SHOCK! DISCONNECT POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING!
STEP #1
POWER OFF
TURN OFF POWER TO RECESSED
FIXTURE AT CIRCUIT BREAKER
to prevent risk of electric shock.
STEP #5
CUTAWAY
VIEW
Gently squeeze together the torsion
springs on the LED downlight to
guide them into the spring brackets
of the fixture, and insert into fixture.
Retrofit Kits are known to be compatible with the following recessed housings Halo: H7ICAT, H7ICT, H7RICT, H750ICAT, H7ICTNB, H7T, Commercial Electric: C1, H4, H2, Juno: IC22, IC22R, IC23W, IC22W, IC23, TC2R, Lithonia: L7X, LC6
STEP #2
Discard any pre-existing bulbs, trim
rings or covers, or socket bracket
from recessed fixture.
STEP #6
Gently push up the LED downlight
until its trim is flush with the ceiling.
Ensure no wires are exposed.
STEP #3
Disconnect the included Edison
base adaptor from the LED downlight, and screw into recessed fixture.
STEP #7
POWER ON BE HAPPY
Restore power to recessed fixture at
circuit breaker.
STEP #4
Re-connect LED downlight to the
Edison base adaptor.
STEP #8
Enjoy energy-efficient LED lighting,
and up to 80% energy savings vs.
equivalent incandescent bulbs.
WARNING – Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaire electrical systems.
If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during
kit installation. This luminaire has been modified and can no longer operate the originally intended lamp.
DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR
ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
UPON INSTALLATION OF DOWNLIGHT RETROFIT, USER MUST MARK THE FOLLOWING ON THE RETROFIT LUMINAIRE
WHERE READILY AVAILABLE BY THE USER DURING NORMAL MAINTENANCE INCLUDING RELAMPING:
"THIS LUMINAIRE HAS BEEN MODIFIED AND CAN NO LONGER OPERATE THE ORIGINALLY INTENDED LAMP".
IN CANADA: THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.
NOT FOR USE IN LUMINAIRE COMPARTMENTS LESS THAN 4" DIAMETER BY 5.25" DEEP.
Meets California Title 24 requirements,
TITLE
24
when installed in a Title 24 compliant
recessed fixture with compatible
push-in connector.
Cumple los requisitos del Titulo 24
de California al instalarse en
lámpara empotrada según el mismo Titulo con conector a presión compatible.
325 Campus Drive • Aurora, OH 44202
MODEL # LED10DR427K
LED DOWNLIGHT RETROFIT KIT QUICK START INSTALLATION GUIDE
WARNING! RISK OF ELECTRIC SHOCK! DISCONNECT POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING!
STEP #1
POWER OFF
TURN OFF POWER TO RECESSED
FIXTURE AT CIRCUIT BREAKER
to prevent risk of electric shock.
STEP #5
CUTAWAY
VIEW
Gently press the support clips on the
LED downlight towards the unit to
insert downlight into recessed fixture.
LED10DR427K is known to be compatible with the following recessed housings Commercial Electric: HBR2000B, HBR2000BICAT, Halo: H99T, H99RT, H99ICT, Juno: TC1R, TC44R, IC1
STEP #2
Discard any pre-existing bulbs, trim
rings or covers, or socket brackets
from recessed fixture.
STEP #6
Gently push up the LED downlight
until its trim is flush with the ceiling.
Ensure no wires are exposed.
STEP #3
RECESSED
FIXTURE
Disconnect the included Edison base
adaptor from the LED downlight, and
screw into recessed fixture.
STEP #7
POWER ON BE HAPPY
RESTORE POWER to recessed fixture
at circuit breaker.
STEP #4
Re-connect LED downlight to the
Edison base adaptor.
STEP #8
Enjoy energy-efficient LED lighting,
and up to 80% energy savings vs.
equivalent incandescent bulbs.
WARNING – Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaire electrical systems.
If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during
kit installation. This luminaire has been modified and can no longer operate the originally intended lamp.
DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR
ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
UPON INSTALLATION OF DOWNLIGHT RETROFIT, USER MUST MARK THE FOLLOWING ON THE RETROFIT LUMINAIRE
WHERE READILY AVAILABLE BY THE USER DURING NORMAL MAINTENANCE INCLUDING RELAMPING:
"THIS LUMINAIRE HAS BEEN MODIFIED AND CAN NO LONGER OPERATE THE ORIGINALLY INTENDED LAMP".
IN CANADA: THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.
NOT FOR USE IN LUMINAIRE COMPARTMENTS LESS THAN 4" DIAMETER BY 5.25" DEEP.
Meets California Title 24 requirements,
TITLE
24
when installed in a Title 24 compliant
recessed fixture with compatible
push-in connector.
Cumple los requisitos del Titulo 24
de California al instalarse en
lámpara empotrada según el mismo Titulo con conector a presión compatible.
325 Campus Drive • Aurora, OH 44202
Loading...