TCL Technoly Electronics SB00005, SB00006 User Manual
C:\Job\HT_CT260H\UC\4463522111\4463522111HTCT260HUC2\00COVHTCT260HUC2\100BCO.fm
masterpage: Left
C:\Job\HT_CT260H\4463522111\4463522111HTCT260HUC2\00COVHTCT260HUC2\010COV.fm
masterpage:
Right
4-463-522-11(1)
Home Theatre
System
Operating Instructions US
Mode d’emploi FR
Manual de instrucciones
ES
©2013 Sony Corporation Printed in China
4-463-522-11(1)
HT-CT260H
4-463-522-11(1)
HT-CT260H
HT-CT260H
HT-CT260H
4-463-522-11(1)
4-463-522-11(1)
C:\Job\HT_CT260H\UC\4463522111\4463522111HTCT260HUC2\01USHTCT260HUC2\020REG.fm
For the customers in the U.S.A
WARNING
To reduce the risk of fire or
electric shock, do not expose this
apparatus to rain or moisture.
The unit is not disconnected from the
mains as long as it is connected to the AC
outlet, even if the unit itself has been
turned off.
To reduce the risk of fire, do not cover the
ventilation opening of the appliance with
newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked
flame sources (for example, lighted
candles).
To reduce the risk of fire or electric shock,
do not expose this appliance to dripping
or splashing, and do not place objects
filled with liquids, such as vases, on the
appliance.
As the main plug is used to disconnect
the unit from the mains, connect the unit
to an easily accessible AC outlet. Should
you notice an abnormality in the unit,
disconnect the main plug from the AC
outlet immediately.
Do not install the appliance in a confined
space, such as a bookcase or built-in
cabinet.
Do not expose batteries or appliances
with battery-installed to excessive heat,
such as sunshine and fire.
In door use only.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Owner’s Record
The model and serial numbers are
located on the rear panel of the unit.
Record the serial numbers in the space
provided below. Refer to them whenever
you call upon your Sony dealer regarding
this product.
Model No. HT-CT260H
Serial No.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
masterpage: Left
C:\Users\ALAYA-32bit\Desktop\Jobs\Sony Japan\HTCT260H\01_4463522111_USFRES\0408_2ndDTP_1\02_FromDTP\03LaESHTCT260HUC2\LaES\090COVIX.fm
masterpage:
Right
Información adicional
US
2
HT-CT260H
HT-CT260H
4-463-522-11(1)
HT-CT260H
4-463-522-11(1)
4-463-522-11(1)
37
ES
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\020REG.fm
010COV.book Page 3 Wednesday, April 10, 2013 7:42 PM
masterpage:
Right
9) Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A
grounding type plug has two blades
and a third grounding prong. The
wide blade or the third prong are
provided for your safety. If the
provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during
lightning storms or when unused for
long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in
any way, such as power-supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been
dropped.
The following FCC statement applies only
to the version of this model
manufactured for sale in the U.S.A. Other
versions may not comply with FCC
technical regulations.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Properly shielded and grounded cables
and connectors must be used for
connection to host computers and/or
peripherals in order to meet FCC
emission limits.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
This equipment must not be co-located
or operated in conjunction with any other
antenna or transmitter.
3
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\020REG.fm
010COV.book Page 4 Wednesday, April 10, 2013 7:42 PM
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment and meets the
FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated
keeping the radiator at least 20 cm or
more away from person’s body
(excluding extremities: hands, wrists,
feet and ankles).
For the customers in the Canada
Properly shielded and grounded cables
and connectors must be used for
connection to host computers and/or
peripherals.
Operation is subject to the following two
conditions:
(1) this device may not cause
interference, and (2) this device must
accept any interference, including
interference that may cause undesired
operation of the device.
This equipment complies with IC
radiation exposure limits set forth for an
uncontrolled environment and meets
RSS-102 of the IC radio frequency (RF)
Exposure rules.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated
keeping the radiator at least 20 cm or
more away from person’s body
(excluding extremities: hands, wrists,
feet and ankles).
Precautions
On safety
Should any solid object or liquid fall into
Do not climb on the Sound Bar or the
On power sources
Before operating the system, check that
If you are not going to use the system
One blade of the plug is wider than the
AC power cord (mains lead) must be
On heat buildup
Although the system heats up during
operation, this is not a malfunction. If you
continuously use this system at a large
volume, the system temperature of the
back and bottom rises considerably. To
avoid burning yourself, do not touch the
system.
masterpage: Left
the system, unplug the system and
have it checked by qualified personnel
before operating it any further.
subwoofer, as you may fall down and
injure yourself, or system damage may
result.
the operating voltage is identical to
your local power supply. The operating
voltage is indicated on the nameplate
at the rear of the Sound Bar.
for a long time, be sure to disconnect
the system from the wall outlet (mains).
To disconnect the AC power cord
(mains lead), grasp the plug itself; never
pull the cord.
other for the purpose of safety and will
fit into the wall outlet (mains) only one
way. If you are unable to insert the plug
fully into the outlet, contact your dealer.
changed only at the qualified service
shop.
US
4
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\020REG.fm
010COV.book Page 5 Wednesday, April 10, 2013 7:42 PM
masterpage:
Right
On placement
Place the system in a location with
adequate ventilation to prevent heat
buildup and prolong the life of the
system.
Do not place the system near heat
sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
Do not place anything at the rear of the
Sound Bar that might block the
ventilation holes and cause
malfunctions.
If the system is being used in
combination with a TV, VCR, or tape
deck, noise may result, and picture
quality may suffer. In this case, place
the system away from the TV, VCR, or
tape deck.
Use caution when placing the system
on surfaces that have been specially
treated (with wax, oil, polish, etc.) as
staining or discoloration of the surface
may result.
Take care to avoid any possible injury
on the corners of the Sound Bar or the
subwoofer.
On operation
Before connecting other equipment, be
sure to turn off and unplug the system.
If you encounter color
irregularity on a nearby TV
screen
Color irregularities may be observed on
certain types of TV sets.
If color irregularity is
observed...
Turn off the TV set, then turn it on again
after 15 to 30 minutes.
If color irregularity is observed
again...
Place the system further away from the
TV set.
On cleaning
Clean the system with a soft dry cloth. Do
not use any type of abrasive pad,
scouring powder or solvent such as
alcohol or benzine.
If you have any question or problem
concerning your system, please consult
your nearest Sony dealer.
Copyrights
This system incorporates Dolby* Digital
and the DTS** Digital Surround System.
* Manufactured under license from
Dolby Laboratories.
Dolby, and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license under
U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide
patents issued & pending. DTS, the
Symbol, & DTS and the Symbol
together are registered trademarks &
DTS Digital Surround and the DTS
logos are trademarks of DTS, Inc.
Product includes software. © DTS, Inc.
All Rights Reserved.
The BLUETOOTH® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under
license.
This system incorporates High-Definition
Multimedia Interface (HDMI™)
technology.
The terms HDMI and HDMI HighDefinition Multimedia Interface, and the
HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the
United States and other countries.
“x.v.Color”and “x.v.Color” logo are
trademarks of Sony Corporation.
5
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\020REG.fm
010COV.book Page 6 Wednesday, April 10, 2013 7:42 PM
masterpage: Left
“WALKMAN” and “WALKMAN” logo are
registered trademarks of Sony
Corporation.
“PlayStation®” is a registered trademark
of Sony Computer Entertainment Inc.
Other trademarks and trade names are
those of their respective owners.
BLUETOOTH wireless
technology
Supported BLUETOOTH version
and profiles
Profile refers to a standard set of
capabilities for various BLUETOOTH
product capabilities. See
“Specifications” (page 32) on the
BLUETOOTH version and profiles
supported by this system.
Notes
For you to use the BLUETOOTH
function, the BLUETOOTH device to be
connected must support the same
profile as this system. Even if the device
supports the same profile, the functions
may differ because of the specifications
of the BLUETOOTH device.
The audio playback on this system may
be delayed from that on the
BLUETOOTH device because of the
characteristics of the BLUETOOTH
wireless technology.
Effective communication range
BLUETOOTH devices should be used
within approximately 10 meters
(33 feet) (unobstructed distance) of
each other. The effective
communication range may become
shorter under the following
conditions.
When a person, metal object, wall or
other obstruction is between the
devices with a BLUETOOTH
connection
Locations where a wireless LAN is
installed
Around microwave ovens that are in
use
Locations where other
electromagnetic waves occur
Effects of other devices
BLUETOOTH devices and wireless LAN
(IEEE 802.11b/g) use the same
frequency band (2.4 GHz). When using
your BLUETOOTH device near a device
with wireless LAN capability,
electromagnetic interference may
occur.
This could result in lower data transfer
rates, noise, or inability to connect. If
this happens, try the following
remedies:
Try connecting this system and
BLUETOOTH mobile phone or
BLUETOOTH device when you are at
least 10 meters (33 feet) away from
the wireless LAN equipment.
Turn off the power to the wireless
LAN equipment when using your
BLUETOOTH device within 10 meters
(33 feet).
Effects on other devices
The radio waves broadcast by this
system may interfere with the
operation of some medical devices.
Since this interference may result in
malfunction, always turn off the power
on this system, BLUETOOTH mobile
phone and BLUETOOTH device in the
following locations:
In hospitals, on trains, in airplanes, at
gas stations, and any place where
flammable gasses may be present
Near automatic doors or fire alarms
US
6
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\020REG.fm
010COV.book Page 7 Wednesday, April 10, 2013 7:42 PM
Notes
This system supports security functions
that comply with the BLUETOOTH
specification as a means of ensuring
security during communication using
BLUETOOTH technology. However, this
security may be insufficient depending
on the setting contents and other
factors, so always be careful when
performing communication using
BLUETOOTH technology.
Sony cannot be held liable in any way
for damages or other loss resulting
from information leaks during
communication using BLUETOOTH
technology.
BLUETOOTH communication is not
necessarily guaranteed with all
BLUETOOTH devices that have the
same profile as this system.
BLUETOOTH devices connected with
this system must comply with the
BLUETOOTH specification prescribed by
the Bluetooth SIG, Inc., and must be
certified to comply. However, even
when a device complies with the
BLUETOOTH specification, there may be
cases where the characteristics or
specifications of the BLUETOOTH device
make it impossible to connect, or may
result in different control methods,
display or operation.
Noise may occur or the audio may cut
off depending on the BLUETOOTH
device connected with this system, the
communications environment, or
surrounding conditions.
masterpage:
Right
7
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\010COVTOC.fm
010COV.book Page 8 Wednesday, April 10, 2013 7:42 PM
Table of contents
Precautions ................................4
BLUETOOTH wireless
technology ...........................6
Getting Started
Unpacking ..................................9
Index to parts and controls .... 10
Connecting a TV, player,
etc. ......................................14
Positioning the system ........... 16
Setting up the Wireless
System ...............................18
Operations and Features
Operating the system
using the supplied
remote control .................. 19
Using the Control for HDMI
function .............................. 19
Setting up the sound output
of the connected
equipment ........................ 20
BLUETOOTH Function
Using the BLUETOOTH
function .............................. 21
Surround Function
Enjoying the surround
effect ..................................24
Advanced Settings
Settings and adjustments
using the AMP menu ........ 25
Linking the system (LINK) .......28
Additional Information
Troubleshooting ......................29
Specifications ..........................32
Index ........................................35
masterpage: Left
US
8
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 9 Wednesday, April 10, 2013 7:42 PM
Getting Started
Unpacking
masterpage:
Right
Subwoofer (SA-WCT260H) (1)
Sound Bar (SA-CT260H) (1)
Digital optical cable for a TV (1)
Remote control (RM-ANP109) (1)
R6 (size AA) battery (1)
Operating Instructions (1)
Warranty (1)
Inserting a battery into the
remote control
Getting Started
Insert an R6 (size AA) battery
(supplied) by matching the and
ends on the battery to the diagram
inside the battery compartment of the
remote control. To use the remote
control, point it at the remote control
sensor at the front of the Sound Bar.
Notes
Do not leave the remote control in an
extremely hot or humid place.
Do not drop any foreign object into the
remote control casing, particularly
when replacing the battery.
Do not expose the remote control
sensor to direct sunlight or lighting
apparatus. Doing so may cause a
malfunction.
If you do not intend to use the remote
control for an extended period of time,
remove the battery to avoid possible
damage from battery leakage and
corrosion.
When you remove the battery, the
manufacturer of TV you set (page 13) is
reset.
9
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 10 Wednesday, April 10, 2013 7:42 PM
Index to parts and controls
For more information, see the pages indicated in parentheses.
Sound Bar
(on/standby)
(remote control sensor)
(BLUETOOTH) key/indicator
INPUT key
Press to select the input source to
play back.
VOL (volume) +/ keys
Front panel display
masterpage: Left
10
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 11 Wednesday, April 10, 2013 7:42 PM
Jacks (on the rear of Sound Bar)
masterpage:
Right
Getting Started
ANALOG IN jack (page 15)
OPTICAL IN jack (page 14)
HDMI TV OUT (ARC) jack
(page 14)
Subwoofer
(on/standby) indicator
(on/standby) button
LINK button (page 28)
AC power cord (mains lead)
HDMI IN jack (page 14)
AC power cord (mains lead)
11
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 12 Wednesday, April 10, 2013 7:42 PM
masterpage: Left
Remote control
This section describes how to operate
the subwoofer, Sound Bar, and
connected equipment using the
remote control supplied. If you cannot
operate the connected equipment,
use the remote control of the
equipment.
Note
Point the remote control towards the
remote control sensor ( ) of the Sound
Bar.
*The and VOL + buttons have a
tactile dot. Use it as a guide during
operation.
To control the system
(on/standby)
INPUT +/ (page 19)
Press to select the equipment you
want to use.
SOUND FIELD (page 24)
DISPLAY
Each time you press the button,
the display turns on or off.
When the system is operated, the
display is lit for several seconds.
MUTING
VOL (volume) +*/
AMP MENU (page 25)
PAIRING (page 22)
RETURN
Returns to the previous screen of
any displayed menu.
(return)/ (select)/
(proceed) or (enter)
Press , , or to select the
menu items. Then press to
enter the selection.
NIGHT (page 24)
To control a TV
TV (on/standby)
Turns on or off the TV that the
remote control is assigned to
operate.
TV VOL (volume) +/
Adjusts the volume.
TV CH (channel) +/
Selects the next (+) or previous ()
channel.
MUTING
INPUT
Selects input.
To control a BLUETOOTH device
/
To go to the beginning of the
previous or next music.
12
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 13 Wednesday, April 10, 2013 7:42 PM
/
To fast reverse or to fast forward
the music when pressed during
playback.
Playback operation
*(playback)/ (pause)/
(stop)
Starts/pauses/stops playback.
To resume normal playback
during pause, press (pause)
again.
Note
The above explanations are intended to
serve as an example only. Depending
on the equipment, the above
operations may not be possible, or may
operate differently than described.
Setting manufacturer of
controllable TVs
1 While holding down the TV
button, press the button
corresponding to the
manufacturer.
masterpage:
Right
Getting Started
Manufacturer Button
SONY TV VOL +
Samsung TV CH +
LG INPUT +
Panasonic TV VOL
VIZIO TV CH
Sharp INPUT
Toshiba STD
2 While keeping TV held
down, press .
3 Release TV .
Note
When you remove the battery, the
manufacturer of TV you set is reset.
Perform steps 1 to 3 again to set the
manufacturer.
13
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 14 Wednesday, April 10, 2013 7:42 PM
Connecting a TV, player, etc.
Before connecting the AC power cord (mains lead) to a wall outlet (mains),
connect all other equipment and a TV to the system. No cable connection is
required between the Sound Bar and the subwoofer because they can be
connected wirelessly.
Connecting a TV
If you connect the system to a TV compatible with the Audio Return Channel
(ARC) technology via an HDMI input jack with “ARC” indicated, you do not need
to connect a digital optical cable.
If the digital optical cable has a cap, remove it before connecting the cable.
masterpage: Left
HDMI cable
(not supplied)
Digital optical cable for a TV
(supplied)
Notes
You can see the letters “ARC” beside the TV’s HDMI jack if it is compatible with the
Audio Return Channel (ARC) technology. Even if you connect an HDMI cable to the
jack, if the HDMI input jack is not compatible with the Audio Return Channel (ARC)
technology, you cannot use the Audio Return Channel (ARC) technology.
The Audio Return Channel (ARC) technology is available only when the Control for
HDMI function is set to on. If the Control for HDMI function is set to off, use a digital
optical cable.
Make sure that you connect cables by matching the shape of the plug to that of the
jack.
Set “TV AUDIO” in the AMP menu according to how the Sound Bar is connected with
a TV (page 26).
When connected via the HDMI jack, select “TV(HDMI).”
US
14
HDMI IN (ARC)
Digital Audio OUT
(optical)
TV
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
“PlayStation®3,” Blu-ray Disc™ player,
DVD player, satellite tuner, cable
television tuner, etc.
HDMI cable
(not supplied)
HDMI OUT
Audio cable (not supplied)
Smartphone, “Walkman,” or
other audio equipment
Audio
signal OUT
CT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 15 Wednesday, April 10, 2013 7:42 PM
When connected via the OPTICAL IN jack, select “OPTICAL.”
When connected via the ANALOG IN jack, select “ANALOG.”
Tip
Even if the system is turned off (active standby mode), the HDMI signal will be sent
from the connected equipment to the TV via the HDMI connection. You can enjoy
image and sound from the equipment on the TV.
Connecting equipment with an HDMI jack
Connecting audio equipment
masterpage:
Right
Getting Started
Note
When you connect a portable music player, etc. via its headphone jack to the ANALOG
IN jack of the system, adjust the volume on the portable music player to eliminate the
volume difference when you switch between the portable music player and other
input sources.
15
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 16 Wednesday, April 10, 2013 7:42 PM
Positioning the system
The illustrations below are examples of how to install the Sound Bar.
Installing the Sound Bar
masterpage: Left
Installing the Sound Bar on a rack Installing the Sound Bar on a wall
(page 17)
Notes
Take following precautions when installing the Sound Bar and the subwoofer.
Do not block the ventilation holes on the rear panel.
Do not place the Sound Bar and the subwoofer in a metal cabinet.
Do not place an object such as an aquarium between the Sound Bar and the
subwoofer.
Place the subwoofer close to the Sound Bar in a same room.
When the Sound Bar is placed in front of a TV, the TV may not be controlled with the
remote control of the TV. In that case, place the Sound Bar away from the TV. If the
remote control of the TV still cannot control the TV, set “IR REP” of the AMP menu to
“ON” (page 27).
Make sure that the remote control of the TV cannot control the TV, then set “IR REP”
to “ON.” If it is set to “ON” when the remote control can control the TV, appropriate
operation may not be obtained, because of the interference between the direct
command from the remote control and the command via the Sound Bar.
16
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
Stand
Hole on the back of the Sound Bar
4mm
(3/16 inches)
More than 30 mm (1 1/4 inches)
5mm
(7/32 inches)
10 mm
(13/32 inches)
592 mm
(23 5/16 inches)
11 to 12 mm
(approx.
15/32 inches)
continued
CT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 17 Wednesday, April 10, 2013 7:42 PM
masterpage:
Right
Removing the stands
When the Sound Bar is to be placed
tilting upward or on a wall, remove the
2 stands at the bottom of the Sound
Bar, as shown below.
Installing the Sound Bar on
a wall
You can install the Sound Bar on the
wall.
Notes
Use screws that are suitable for the wall
material and strength. As a plaster
board wall is especially fragile, attach
the screws securely to a wall beam.
Install the Sound Bar on a vertical and
flat reinforced area of the wall.
Be sure to subcontract the installation
to Sony dealers or licensed contractors
and pay special attention to safety
during the installation.
Sony is not responsible for accidents or
damage caused by improper
installation, insufficient wall strength,
improper screw installation or natural
calamity, etc.
1 Prepare screws (not supplied)
that are suitable for the holes on
the back of the Sound Bar.
Getting Started
2 Fasten the screws to the wall.
The screws should protrude 11 to
12 mm (approx. 15/32 inches).
17
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\030GET.fm
010COV.book Page 18 Wednesday, April 10, 2013 7:42 PM
3 Hang the Sound Bar onto the
screws.
Align the holes on the back of the
Sound Bar to the screws, then
hang the Sound Bar onto the
2screws.
Setting up the Wireless
System
The Sound Bar transmits sound from
the equipment to the subwoofer by
wireless communication.
masterpage: Left
1 Connect the AC power cord
(mains lead) of the subwoofer
to a wall outlet (mains).
The indicator of the
subwoofer lights up in red.
If it does not light up, press the
button of the subwoofer and
wait for the indicator to light up in
red.
2 Connect the AC power cord
(mains lead) of the Sound Bar to
a wall outlet (mains).
3 Press the button of the
Sound Bar.
When the wireless connection is
made, the indicator of the
subwoofer turns green. If it does
not turn green, perform the
operations of “Linking the system
(LINK)” (page 28).
US
18
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\040PLA.fm
010COV.book Page 19 Wednesday, April 10, 2013 7:42 PM
masterpage:
Right
Operations and Features
Operating the system
using the supplied
remote control
1
Turn on the system.
2 Press INPUT to display the input
source on the front panel
display of the Sound Bar.
Input source Playable equipment
HDMI Equipment connected
TV(HDMI) TV connected to the
OPTICAL TV or other
ANALOG TV or other
BT AU BLUETOOTH device
to the HDMI IN jack
HDMI TV OUT (ARC)
equipment connected
to the OPTICAL IN jack
equipment connected
to the ANALOG IN jack
connected
3 Adjust the volume by pressing
VOL +/.
Tip
The sound may be output from the TV’s
speaker. In this case, turn the volume of
the TV’s speaker down to minimum.
Using the Control for
HDMI function
By enabling the Control for HDMI
function (CTRL, page 26), and
connecting equipment that is
compatible with the Control for HDMI
function via an HDMI cable, operation
is simplified with the features below.
System Power Off
When you turn off the TV using the
power button on the TV’s remote
control, the system and the connected
equipment turn off automatically.
System Audio Control
If you turn on the system while you are
watching the TV, the TV sound is
output from the speakers of the
system automatically. The volume of
the system is adjusted when you
adjust the TV volume.
If the TV sound was output from the
speakers of the system the last time
you turned off the TV, the system is
turned on automatically when you
turn on the TV again, and the TV sound
is output from the speakers of the
system automatically.
Audio Return Channel
(ARC)
Operations and Features
If the TV is compatible with the Audio
Return Channel (ARC) technology, an
HDMI cable connection also sends a
digital audio signal from the TV to the
system. You do not need to make a
separate audio connection for
listening to TV sound from the system.
19
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\040PLA.fm
010COV.book Page 20 Wednesday, April 10, 2013 7:42 PM
masterpage: Left
One-Touch Play
When you play the equipment
connected to the system with an HDMI
cable, the connected TV is turned on
automatically and the input signal of
the system is switched to the
appropriate HDMI input.
Tip
For example, set your TV as follows to
use the Control for HDMI function:
Set the HDMI link setting to on.
Select “AV amplifier” for a priority
speaker, etc.
Notes
The above features may not operate
with certain equipment.
Depending on the settings of the
connected equipment, the Control for
HDMI function may not work correctly.
Refer to the operating instructions of
the equipment.
Notes on HDMI
connections
Use a High Speed HDMI cable. If you
use a Standard HDMI cable, 1080p,
Deep Color, or 3D images may not be
displayed properly.
We recommend that you use an
HDMI authorized cable or a Sony
HDMI cable.
We do not recommend using an
HDMI-DVI conversion cable.
Check the setup of the connected
equipment if an image is poor or the
sound does not come out of the
equipment connected via the HDMI
cable.
Audio signals (sampling frequency,
bit length, etc.) transmitted from an
HDMI jack may be suppressed by the
connected equipment.
Sound may be interrupted when the
sampling frequency or the number
of channels of audio output signals
from the playback equipment is
switched.
When the connected equipment is
not compatible with copyright
protection technology (HDCP), the
image and/or the sound from the
HDMI TV OUT (ARC) jack may be
distorted or may not be output. In
this case, check the specification of
the connected equipment.
This system supports Deep Color,
“x.v.Color,” and 3D transmission.
To enjoy 3D images, connect a 3D-
compatible TV and video equipment
(Blu-ray Disc player, “PlayStation
etc.) to the system using High Speed
®
3,”
HDMI cables, put on 3D glasses, and
then play back 3D compatible Bluray Disc.
Setting up the sound
output of the connected
equipment
To output multi-channel digital audio,
check the digital audio output setting
on the connected equipment.
For details, refer to the operating
instructions supplied with the
connected equipment.
20
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\050BLT.fm
010COV.book Page 21 Wednesday, April 10, 2013 7:42 PM
6 Make the BLUETOOTH
BLUETOOTH Function
Using the BLUETOOTH
function
Pairing automatically
If the system is not paired with any
equipment, you must pair the system
with the equipment to be connected.
Select “BT AU” with the INPUT +/
buttons on the remote control to enter
pairing mode.
1 Place the system and a
BLUETOOTH device within
1 meter (3.3 feet).
2 Press INPUT +/ to select “BT
AU.”
3 Set the BLUETOOTH device in
pairing mode.
For details on setting the
BLUETOOTH device in pairing
mode, refer to the operating
instructions supplied with the
device.
4 When the detected devices are
listed on the BLUETOOTH
device, check that “SONY
HT-CT260H” is listed.
On some BLUETOOTH devices, the
list may not be displayed.
5 Select “SONY HT-CT260H” on
the list.
If entering a Passkey is requested,
enter “0000.”
About the LED for BLUETOOTH
The (BLUETOOTH) indicator lights
up or flashes in blue to indicate the
BLUETOOTH status.
System status Indicator status
During BLUETOOTH
pairing
The system is
attempting to
connect with a
BLUETOOTH device
The system has
established in
connection with a
BLUETOOTH device
The system is in
BLUETOOTH
standby mode
(when the system is
off)
Notes
For details on operation of the
connected devices, refer to the
operating instructions supplied with the
devices.
The BLUETOOTH devices to be
connected must support A2DP
(Advanced Audio Distribution Profile).
Use a BLUETOOTH device such as
BLUETOOTH mobile phone in an easily
visible place in the same room where
the Sound Bar is placed.
If Wi-Fi equipment is used, BLUETOOTH
communication may become unstable.
In that case, use the BLUETOOTH device
as close as possible to the Sound Bar.
masterpage:
connection on the BLUETOOTH
device.
When the BLUETOOTH connection
is made correctly, the
(BLUETOOTH) indicator lights
up in blue and the pairing
information is stored in the
system.
Flashes quickly in
blue.
Flashes in blue.
Lights up in blue.
Flashes slowly in
blue.
Right
BLUETOOTH Function
21
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\050BLT.fm
010COV.book Page 22 Wednesday, April 10, 2013 7:42 PM
masterpage: Left
Sound may be interrupted because of a
problem with the BLUETOOTH device.
Once a pairing operation is performed,
it does not have to be performed again.
However, you must repeat pairing in the
cases listed below.
Pairing information is deleted by
repairing the system.
Pairing for 9 or more devices is to be
set.
This system can set pairing with up to
8 devices. If pairing is to be set on a
device after pairing has been set on
8 devices, the pairing information on
a device whose connection date is the
oldest is overwritten with new
information.
The connection history with this
system is deleted on the connected
device.
The system is reset to default.
Pairing manually
If you intend to pair the system with 2
or more BLUETOOTH devices, manual
pairing is necessary.
1 Place the BLUETOOTH device to
be connected to this system
within 1 meter (3.3 feet) of the
system.
2 Press PAIRING on the remote
control, or press the
(BLUETOOTH) key on the
Sound Bar for more than
2seconds.
3 Perform steps 3 to 6 in “Pairing
automatically” (page 21).
Notes
“Passkey” may be called “Passcode,”
“PIN code,” “PIN number” or
“Password,” etc., depending on the
device.
The pairing standby status of the
system is canceled after about 1 minute.
If pairing is not successful, redo the
procedure from step 1.
If you wish to pair with several
BLUETOOTH devices, perform the
procedure from steps 1 to 3 individually
for each BLUETOOTH device.
If no pairing information is stored in the
system, the system automatically
enters pairing mode when “BT AU” is
selected as input. In this case, pairing
mode is not released automatically.
Listening to music with the
BLUETOOTH connection
You can listen to a music that supports
SCMS-T content protection.
Before starting music playback, check
the following:
The BLUETOOTH function on the
BLUETOOTH device is on.
The pairing procedure is completed
on both this system and the
BLUETOOTH device.
1 Press INPUT +/ to select “BT
AU.”
2 Start the BLUETOOTH
connection from the
BLUETOOTH device.
The (BLUETOOTH) indicator
lights up in blue when the
BLUETOOTH connection is
established.
3 Start playback on the
BLUETOOTH device.
For details on operation, see “To
control a BLUETOOTH device”
(page 12).
4 Adjust the volume.
Set the volume of the BLUETOOTH
device to a moderate level and
press VOL +/.
22
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\050BLT.fm
010COV.book Page 23 Wednesday, April 10, 2013 7:42 PM
Tips
You can adjust the volume of the
system via a BLUETOOTH device
supporting AVRCP (Audio Video
Remote Control Profile) VOLUME UP/
DOWN. For details, refer to the
operating instructions supplied with the
device.
You may not be able to adjust the
volume, depending on the device.
Notes
If the source device has a bass boost
function or equalizer function, turn
them off. If these functions are on,
sound may be distorted.
In the following cases, you will have to
make the BLUETOOTH connection
again.
The power of the system is not on.
The power of the BLUETOOTH device
is not on, or the BLUETOOTH function
is off.
The BLUETOOTH connection is not
established.
If more than one devices paired with the
system are playing, sound will be heard
from just one of those devices.
masterpage:
Right
BLUETOOTH Function
Finishing the BLUETOOTH
connection
Terminate the BLUETOOTH
connection by any of the operations
listed below.
Operate the BLUETOOTH device to
terminate the connection. For
details, refer to the operating
instructions supplied with the device.
Turn off the BLUETOOTH device.
Turn off the system.
23
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
NIGHT
SOUND
FIELD
CT260H\07_FromDTP\02_UC\02_US\US\060SUR.fm
010COV.book Page 24 Wednesday, April 10, 2013 7:42 PM
Available sound fields
masterpage: Left
Surround Function
Enjoying the surround
effect
This system can create multi-channel
surround sound. You can select one of
system’s optimized pre-programmed
sound fields.
Select a sound field by pressing the
SOUND FIELD button of your
desired sound field.
The selected sound field appears on
the display of the Sound Bar.
The default setting of the sound field
function of the system is “STANDARD.”
Sound field Effect
STANDARD
(STD)
MOVIE Recreates powerful and
GAME Produces powerful and
MUSIC Suits for music programs or
P.AUDIO
(Portable
audio)
STEREO Suits for music CDs.
Tip
You can set a different sound field for
each input source.
Suits various sources.
realistic sound, along with
clear dialog.
realistic sound, suited for
playing video games.
music videos on Blu-ray
Discs/DVDs.
Suits for music programs of
a portable music player.
Using the NIGHT mode
You can enjoy sound effects and hear
the dialog clearly even at a low volume
level using this function.
Press NIGHT.
The NIGHT function is enabled or
disabled cyclically. On the front panel
display, “N. ON” appears when the
NIGHT function is enabled and “N.
OFF” when it is disabled.
24
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\070ADV.fm
010COV.book Page 25 Wednesday, April 10, 2013 7:42 PM
Advanced Settings
Settings and adjustments using the AMP menu
Using the AMP menu
You can set the following items with AMP MENU on the remote control.
The default settings are underlined.
Your settings are retained even if you disconnect the AC power cord (mains lead).
1 Press AMP MENU to turn on the AMP menu.
2 Press (return)/ (select)/ (proceed) repeatedly to select the item
and press to decide the setting.
3 Press AMP MENU to turn off the AMP menu.
Menu list
Menu items Function
LEVEL SW LVL Adjusts the subwoofer level.
DRC
(DYNAMIC RANGE
CONTROL)
TONE BASS Adjusts the bass level.
TREBLE Adjusts the treble level.
The parameters range from “6” to “+6” in 1-step
increments.
Useful for enjoying movies at low sound volume. DRC
applies to Dolby Digital sources.
ON: Compresses sound in accordance with the information
contained in the content.
OFF: Sound is not compressed.
The parameters range from “6” to “+6” in 1-step
increments.
The parameters range from “6” to “+6” in 1-step
increments.
masterpage:
Right
Advanced Settings
25
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
Notes
CT260H\07_FromDTP\02_UC\02_US\US\070ADV.fm
010COV.book Page 26 Wednesday, April 10, 2013 7:42 PM
Menu items Function
AUDIO SYNC
(AV SYNC)
EFFECT
(SOUND EFFECT)
DUAL
(DUAL MONO)
TV AUDIO Selects the TV sound to be output.
HDMI C.HDMI
SET BT BT.STBY
(CONTROL FOR
HDMI)
P. THRU
(PASS THROUGH)
(BT STANDBY)
You can delay the sound using this function when the image
is slower than the sound.
ON: Adjusts the difference between picture and sound.
OFF: No adjustment.
You can set the system's sound effects (sound field setting)
on/off.
ON: Enables the sound effects of the sound field.
OFF: The sound effects are disabled. You can hear sound as
it is recorded.
You can enjoy multiplex broadcast sound when the system
receives a Dolby Digital multiplex broadcast signal.
MAIN/SUB: Main sound is output from the left speaker and
sub sound is output from the right speaker.
MAIN: Plays back only the main channel.
SUB: Plays back only the sub channel.
TV(HDMI): Select this setting when the system is connected
to a TV (ARC) jack of the TV with an HDMI cable.
OPTICAL: Select this setting when the system is connected
to a TV with the digital optical cable.
ANALOG: Select this setting when the system is connected
to a TV with an audio cable.
ON: Turns on the Control for HDMI function.
OFF: Turns off the function. Select this setting when you
want to connect equipment not compatible with the
Control for HDMI function.
ON: When the system is in standby mode, it always passes
HDMI signals through.
OFF: When the Sound Bar is turned off, the system does not
pass HDMI signals to a TV.
When the system has pairing information, the system is in
BLUETOOTH standby mode even when it is turned off.
ON: BLUETOOTH standby mode is enabled. The
illumination LED flashes in blue slowly when the system is
turned off.
OFF: BLUETOOTH standby mode is disabled.
masterpage: Left
26
If the system does not have pairing information,
BLUETOOTH standby mode cannot be set.
During BLUETOOTH standby mode, standby power
consumption increases.
US
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\070ADV.fm
010COV.book Page 27 Wednesday, April 10, 2013 7:42 PM
Menu items Function
SYSTEM A. STBY
WS LINK Use this item when you want to enable the wireless
(AUTO STANDBY)
IR REP If the remote control of a TV cannot control the TV, the Sound
VERSION The current firmware version information appears on the
You can reduce power consumption. The Sound Bar enters
standby mode automatically when you do not operate the
Sound Bar for about 20 minutes and the Sound Bar is not
receiving an input signal.
ON: Turns on the “A. STBY” function.
OFF: Turns off the function.
Bar can relay the remote control signal to the TV to control
the TV.
ON: The relay function is enabled.
OFF: The relay function is disabled.
front panel display.
transmission (page 28).
masterpage:
Right
Advanced Settings
27
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
AMP
MENU
CT260H\07_FromDTP\02_UC\02_US\US\070ADV.fm
010COV.book Page 28 Wednesday, April 10, 2013 7:42 PM
5 “START” appears, then press .
Linking the system
(LINK)
You can link the Sound Bar and the
subwoofer again to enable wireless
transmission between them.
6 Press AMP MENU.
masterpage: Left
“SEARCH” appears, and the Sound
Bar searches for equipment that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function during a
search for equipment, press .
When subwoofer is linked with the
Sound Bar, the indicator on
the subwoofer lights up in green
and the subwoofer beeps once.
“OK” appears on the front panel
display.
If “FAILED” appears or the
subwoofer does not stop beeping,
perform the process again from
step 1.
The AMP menu turns off.
1 Press LINK on the rear of the
subwoofer with the point of a
pen, etc.
The subwoofer keeps beeping for
a certain time. Perform steps 2 to 5
before the subwoofer stops
beeping.
2 Press AMP MENU.
3 Select “WS” with (select),
then press .
4 Select “LINK,” then press .
US
28
HT-CT260H
4-463-522-11(1)
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HT-
continued
CT260H\07_FromDTP\02_UC\02_US\US\080ADD.fm
010COV.book Page 29 Wednesday, April 10, 2013 7:42 PM
instructions supplied with the
connected equipment.
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the system, use
this troubleshooting guide to help
remedy the problem before
requesting repairs. Should any
problem persist, consult your nearest
Sony dealer.
POWER
The system is not turned on.
Check that the AC power cord
(mains lead) is connected securely.
The system is turned off
automatically.
The “A. STBY” function is working
(page 27).
SOUND
Dolby Digital or DTS multi-channel
sound is not reproduced.
Check the audio setting of Dolby
Digital or DTS format on the Blu-ray
Disc player, DVD player, etc.,
connected to the system.
The surround effect cannot be
obtained.
Depending on the input signal and
the setting for the sound field,
surround sound processing may not
work effectively. The surround effect
may be subtle depending on the
program or disc.
If you connect a Blu-ray Disc player
or a DVD player compatible with the
surround effect function, the
surround effect of the system may
not work. In this case, set the
surround effect function of the
connected equipment to off. For
details, refer to the operating
No TV sound is output from the
system.
Check the connection of the digital
optical cable or audio cable that is
connected to the system and the TV
(page 14).
Check the sound output of the TV.
If the TV is not compatible with the
Audio Return Channel (ARC)
technology, connect the digital
optical cable in addition to the HDMI
cable (page 14) in order to output
sound.
Check that “TV AUDIO” in the AMP
menu is set correctly (page 26).
The sound is output from both the
system and the TV.
Turn off the sound of the system or
the TV.
Sound lags behind the TV image.
Set the “SYNC” to “OFF” if “SYNC” is
set to “ON” (page 26).
No sound or only a very low-level
sound of the connected equipment
is heard from the system.
Press VOL + and check the volume
level.
Press MUTING or VOL + to cancel the
muting function.
Check that the input source is
correctly selected.
Check that all the cables and cords
of the system and the connected
equipment are fully inserted.
BLUETOOTH
There is no sound.
Make sure this system is not too far
from the BLUETOOTH device, or this
system is not receiving interference
from a Wi-Fi network, other 2.4 GHz
wireless device, or microwave oven.
masterpage:
Right
Additional Information
29
HT-CT260H
4-463-522-11(1)
US
C:\Users\ALAYA-Win7\Desktop\Eric's Data\HTCT260H\07_FromDTP\02_UC\02_US\US\080ADD.fm
010COV.book Page 30 Wednesday, April 10, 2013 7:42 PM
masterpage: Left
Check that the BLUETOOTH
connection is made properly
between this system and the
BLUETOOTH device.
Pair this system and the
BLUETOOTH device again.
Sound skips or the correspondence
distance is short.
If a device that generates
electromagnetic radiation, such as a
Wi-Fi network, other BLUETOOTH
device(s), or a microwave oven is
nearby, move this system away
from such sources.
Remove any obstacle between this
system and the BLUETOOTH device,
or move this system away from the
obstacle.
Locate this system and the
BLUETOOTH device as near as
possible.
Re-position this system.
Re-position the BLUETOOTH device.
Change the Wi-Fi frequency of the
Wi-Fi router, computer, etc., to
5GHz band.
Pairing cannot be done.
Bring this system and the
BLUETOOTH device closer together.
The sound is not in sync with the
image.
When you are watching movies, you
may hear the sound with a slight
delay from the image.
The BLUETOOTH connection cannot
be completed.
Make sure the BLUETOOTH device
to be connected is turned on and
the BLUETOOTH function is
enabled.
The BLUETOOTH connection has
become disconnected. Make the
BLUETOOTH connection again.
BLUETOOTH devices cannot be
operated on the remote control of
the system.
Operate the BLUETOOTH device on
itself.
WIRELESS SOUND
Wireless transmission is not
activated or there is no sound from
the subwoofer.
Check the status of the
indicator on the subwoofer.
Is off:
Check that the AC power cord
(mains lead) of the subwoofer is
connected securely.
Turn on the subwoofer by
pressing on the subwoofer.
Flashes in red:
Press to turn off the
subwoofer, and check that
nothing is blocking the
ventilation holes of the
subwoofer.
Flashes in green slowly or is lit in
red:
Move the subwoofer so that the
indicator lights up in green.
Link the system (page 28).
Flashes in green quickly:
Consult your nearest Sony
dealer.
Sound skips or has noise.
If a device that generates
electromagnetic radiation, such as a
Wi-Fi network, or a microwave oven
is nearby, move this system away
from such sources.
Remove any obstacle between the
Sound Bar and the subwoofer, or
move this system away from the
obstacle.
Locate the Sound Bar and the
subwoofer as near as possible.
Change the Wi-Fi frequency of the
Wi-Fi router, computer, etc., to
5GHz band.
30
US
HT-CT260H
4-463-522-11(1)
Loading...