TCL Technoly Electronics 03 Users Manual

PRODUCTS USERMANUAL

WIFI Module

WF78RL1500C

IEEE

Model

802.11b/g/n

:WF78RL1500C

1T/1R

Product Description

WF78RL1500C is to specify the product requirements for 802.11b/g/n Module. This
Card is based on MTK MT7601 chipset that complied with IEEE 802.11n,and it is
also backward complied with IEEE 802.11b/g standard from 2.4GHz.It can be used
to provide up to 54Mbps for IEEE 802.11g, 11Mbps for IEEE 802.11b and 150Mbps
for IEEE 802.11n to connect your wireless LAN.

Product Features

◆ Complies with IEEE 802.11g; 802.11b; 802.11n standard for 2.4GHz Wireless
LAN.

◆ Supports Ad-Hoc/Infrastructure modes

◆ Works with all existing network infrastructure.

◆ Supports Wi-Fi Protected Setup (WPS) configuration function

◆ Capable of up to 128-Bit WEP Encryption.

◆ Freedom to roam while staying connected.

◆ 22-Mbps Packet Binary Convolution Coding (PBCC)

(according to the IEEE Std 802.11b high-rate specification ).

◆ UP to 54 Mbps High-Speed Transfer Rate in 802.11g mode of operation.

◆ Integrated Antenna.

◆ Supports Windows 2000, XP32/64,Vista32/64,Linux

◆ Low power consumption.

◆ Easy to install and configure.

PAGE 1 OF 3

Version 1.0

PRODUCTS USERMANUAL

WF78RL1500C

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.
This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and

2. The transmitter module may not be co-located with any other transmitter or antenna,

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labelling

This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users.

The final end product must be labelled in a visible area with the following:
“Contains FCC ID:ZVA03”.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or

remove this RF module in the user’s manual of the end product which integrates this module.

PAGE 2 OF 3

Version 1.0