TCL TWC-15CR/UH (ES), TWC-18CR2/UH (ES), TWC-22CR2/UH (ES), TWC-24CR2/UH (ES) Operating Instructions Manual
TWC-15CR/UH (ES)
TWC-18CR2/UH (ES)
TWC-22CR2/UH (ES)
TWC-24CR2/UH (ES)
INTRODUCTION
IMPORTANT SAFETY INSTRUCTION ...........................................................................
ELECTRICAL REQUIREMENTS
PACKING LIST ............................................................................................................
INSTALLATION & ASSEMBLY INSTRUCTIONS ..............................................................
USING YOUR AIR CONDITIONER ................................................................................
OPERATING YOUR AIR CONDITIONER
CARE AND CLEANING ................................................................................................
TROUBLESHOOTING .................................................................................................
...................................................................................
........................................................................
1
2
3
4
13
15
16
17
1
15K 18K/22K/24K
2
5/16" Long Hex-head Screw
5/8" Long Hex-head Screw
1/2" Long Hex-head Screw
5/8" Long Flat Head Bolt and
Locknut
Sill Angel Bracket
1/2" Long Flat Head Bolt and
Locknut
Gasket
Support Bracket(with R and L
remark)
3
15K/18K
17.91 18.625
23.625 26.50
19.00 19.50
28.00 30.00
41.00 41.00
4
22K/24K
(15K/18K See FIG.1/FIG.2 ; 22K/24K See FIG.3/FIG.4).
FIG.1
FIG.3
SASH
19 MIN
1/2 MIN
Storm Window Frame or Obstruction
SASH
19 1/2 MIN
1/2 MIN
FIG.2
1/2 MIN
Storm Window Frame
or Obstruction
1/2 MIN
FIG.4
1/2 MIN
1/2 MIN
SASH
19 MIN
SASH
19 1/2 MIN
Storm Window Frame or Obstruction
Storm Window Frame
or Obstruction
5
FIG.5
FIG.6
FIG.5
FIG.7
FIG.7 & 8
FIG.6
FIG.9
FIG.9
FIG.8
6
6.Remove the six screws from the cabinet.( ) (FIG.10)There are two screws on the top, left and right.
FIG.10
FIG.11
FIG.11
Do not
pull or
lift in
this
area
This may
result in
damage.
8. (FIG.12).Remove the shipping block for the 24K
FIG.12
7
5/16
Long
Hex-head
Screw
FIG.13a
FIG.13a
(FIG.13b-14).
FIG.13b
5/16" Long
Hex-head Screw
FIG.14
()It is suggested to keep a downward angle so
accumulated rain water can drain out from the
backside of the unit.
8
(It should set on the gasket for 22K/24K)
Long Flat head
Bolt and Locknut
5/8" Long Flat Head Bolt
5
Long
Flat head Bolt
and Locknut
5/8" Long
Hex-head Screw
Gasket
5/8" Long
Hex-head Screw
1/2" Long
Hex-head Screw
9
sash lock
Sash Lock
5/8" Long
Hex-head Screw
FIG.15
10
15K/18K
22K/24K
18 1/4 (46.4 cm)
23 7/8 (60.6 cm)
19 1/2 (49.5 cm)
26 9/10 (68.3 cm)
FIG.16
Y
(Page 6 and 7)
11
FIG.17
FIG.18
FIG.19
FIG.20
12
1
2
AUTO
SPEED
AUTO
MODE
3
9
1. Without timer setting,the
Digital Display:
7
8
operation mode is Cooling,Dry, Fan and Auto,and
the set temperature will be displayed.
Time will be displayed under timer setting.
and Button:2. Use these buttons on the
control panel and remote to increase or decrease
the Set Temperature or Timer.
Temperature range: 61 ~88 or 16 ~31 .
3. Turn the air conditioner on and
Power Button:
off.
Press the mode button to cycle
4. Mode Button:
through the various modes: Cool, Dry, Fan and
Auto.
5
6
4
Cool Mode: The cooling function allows the air
conditioner to cool the room and at the same time
reduces Air . Press the MODE button to
humidity
activate the cooling function. To optimize the
function of the air conditioner, adjust the
temperature and the speed by pressing the button
indicated.
Dry Mode: This function reduces the humidity of
the air to make the room more comfortable. Press
MODE button to set the DRY mode. An automatic
function of alternating cooling cycles and air fan
is activated.
Fan Mode: The conditioner works in only
ventilation. Press MODE button to set the FAN
mode. With pressing FAN SPEED button the
speed changes in the following sequence: Hi, Med
and Lo in FAN mode. The remote control also
stories the speed that was set in the previous
mode of operation.
Auto Mode: In AUTO mode the unit automatically
chooses the fan speed and the mode of operation
(COOL,DRY or FAN).In this mode the fan speed
and the temperature are set automatically
according to the room temperature (tested by the
temperature sensor which is incorporated in the
indoor unit.).
5. Timer Button:
Use these buttons on the control
panel and remote to set the Timer.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the rest time by
pressing the button or until the rest
time displayed is to your demand then press
TIMER button again.
Timer On: When the unit is off, press TIMER
button at the first time, set the temperature with
pressing the button or . Press TIMER
button at the second time, set the rest time with
pressing the button or . Press TIMER
button at the third time, confirm the setting,
will automatically switch on and show on the
display.
Note: It can be set to automatically turn off or on
in 0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER
button again.
then it
13
When the unit is in ECO mode, the
6. Eco Button:
light will turn on. In ECO mode, the unit will
turn off once the room is cooled to the user set
temperature. The fan will also be off at this point.
The unit will turn back on when the room
temperature rises above the user set temperature.
Before the compressor starts, the fan motor will
run for a while, then it will stop for a while, and will
repeat to provide a much more comfortable feeling
and save energy.
Press the SLEEP button, the Sleep
7. Sleep Button:
Light will be on , and
display lights will turn off.
for 10 seconds then all of the
In SLEEP mode, the airconditioner will automatically adjust the temperature and fan speed to make the room more comfortable during the night. The set temperature will
automatically raise by 1 every 30-60 minutes
.8
and at most change six times until the set
temperature is .
82.4
10.
To direct the airflow,
Directional Louvers:
use the
direction, control the
horizontal wheel to control the horizontal
and use the air deflectors to
vertical direction.
horizontal wheelair deflector air deflector
Press the FAN SPEED button
8. Fan Speed Button:
to choose the fan speed options. You can choose
Hi, Med, Lo or auto speed in COOL mode and
choose Hi, Med, Lo in FAN mode.
9.
When the Filter Check light is off,
Filter Button:
it is useless to press the Filter Check button. When
the Filter Check light is on, it can turn off the light
by pressing the Filter Check button. After the
fan motor works for 500 total hours, the Filter
Check light will turn on to remind the user to clean
the filter.
14
1
3
4
5
6
3
2
7
8
9
10
Use these buttons on the control panel
5. Timer:
and remote to set the Timer.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the rest time by
pressing the button or until the rest
time displayed is to your demand then press
TIMER button again.
Timer On: When the unit is off, press TIMER
button at the first time, set the temperature with
pressing the button or . Press TIMER
button at the second time, set the rest time with
pressing the button or . Press TIMER
button at the third time, confirm the setting, then
the rest time to next automatical switching-on
could be read on the display of the machine.
Note: It can be set to automatically turn off or on
in 0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below
10 hours and 1 hour increment for 10 hours or
above. The SET light will turn on while setting.
To cancel the set function, press the TIMER
button again.
1. Turn the air conditioner on and off.Power:
2. Press the COOL button to COOL mode.Cool:
and :3. Use these buttons on the control
panel and remote to increase or decrease the
Set Temperature or Timer . T emperature range:
61 ~88 or 16 ~31 .
Press the SLEEP button, the Sleep
4. Sleep:
Light will be on , and
display lights will turn off.
conditioner will automatically adjust the temperature and fan speed to make the room more comfortable during the night. The set temperature will
automatically raise by 1 every 30-60 minutes
and at most change six times until the set
temperature is .
for 10 seconds then all of the
In SLEEP mode, the air-
.8
82.4
In AUTO mode the unit automatically
6. Auto Mode:
chooses the fan speed and the mode of operation
(COOL,DRY or FAN).In this mode the fan speed
and the temperature are set automatically according
to the room temperature (tested by the temperature
sensor which is incorporated in the indoor unit.).
Press the FAN SPEED button to
7. Fan Speed:
choose the fan speed options. You can choose
Hi, Med, Lo or auto speed in COOL mode and
choose Hi, Med, Lo in FAN mode.
To press the DISPLAY button, it can
8. Display:
switch off/on all lights or LED display.
When the unit is in ECO mode, the light
9.
Eco:
will turn on. In ECO mode, the unit will turn off
once the room is cooled to the user set
temperature. The fan will also be off at this
point. The unit will turn back on when the room
temperature rises above the user set
temperature.Before the compressor starts, the fan
motor will run for a while, then it will stop for a while,
and will repeat to provide a much more comfortable
feeling and save energy.
15
Fan Only:
Press the Fan Only button to FAN
10.
ONLY mode.
FIG.21
FIG.21
16
17
18
Loading...