TCL TAC-12CHSD-TPG11IT, TAC-24CHSD-TPG11IT, TAC-18CHSD-TPG11IT User Manual

CONTENTS

SAFETY PRECAUTIONS

NAMES OF PARTS

INDOOR UNIT DISPLAY

EMERGENCY FUNCTION & AUTO-RESTART FUNCTION

REMOTE CONTROLLER

OPERATING INSTRUCTIONS

INSTALLATION MANUAL

MAINTENANCE

TROUBLESHOOTING

................................................................................................................4

....................................................................................................................35

..................................................................................................1

.......................................................................................................5

.......................................................................................................7

.............................................................................................11

....................................................................................................20

..........................................................................................................36

.............................................6

SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER

The ratings of the fuse installed in the built

in control unit are 4A / 250V .

The appliance must be fitted with means for

disconnection from the supply mains having a
contact separation in all poles that provide full
disconnection under overvoltage category III
conditions, and these means must be incorporated
in the fixed wiring in accordance with the wiring
rules.

Only use the air conditioner as instructed in

this booklet.

The appliance must be installed in accordance

with applicable national regulations.

Before accessing the terminals , all the power

circuits must be disconnected from the power
supply.

The appliance shall be installed in accordance

with national wiring regulations.

1

SAFETY RULES AND RECOMMENDATIONS FOR THE USER

Cleaning and maintenance must be carried out

by specialized technical personnel. In any case
disconnect the appliance from the mains
electricity supply before carrying out any
cleaning or maintenance.

This appliance has been made for air

conditioning domestic environments and must
not be used for any other purpose.

The batteries in remote controller must be

recycled or disposed of properly.

If the appliance gives off smoke or there is a

smell of burning, immediately cut off the pow
er supply and contact the Service Centre.

Have repairs carried out only by an authorised

Service Centre of the manufacturer . Incorrect
repair could expose the user to the risk of
electric shock, etc.

Unhook the automatic switch if you foresee

not to use the device for a long time.
The airflow direction must be properly adjusted

2

SAFETY RULES AND PROHIBITIONS

Do not obstruct the air inlet or outlet of the

indoor or the outdoor unit.
The obstruction of these openings causes a
reduction in the operative efficiency of the
conditioner with possible consequent failures
or damages.

This appliance is not intended for use by

persons (including children ) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.

Children should be supervised to ensure

that they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer,its service
agent or similarly qualified persons in
order to avoid a hazard.

3

NAMES OF PARTS

Indoor unit

Outdoor unit

Mounting plate

Air filter

Air inlet

Front panel

Emergency button

Air outlet

Air deflector and flap

Refrigerant
connection pipe

Remote controller

Air inlet

Air outlet

Note: This figure shown may be different from the actual
object. Please take the latter as the standard.

With the protective
cover removed

4

Wiring cover

Drainage pipe

Connection wiring

Valve protective cover

Gas valve
(Low pressure valve)

Liquid valve
(High pressure valve)

INDOOR UNIT DISPLAY

2

3

1

No.

Led

1

SLEEP

Temperature display (if present)

2

/Error code

TIMER

3

The shape and position of switches and indicators may be different according to the model, but their
function is the same.

Function

SLEEP mode

(1) Lights up during Timer operation when
the air conditioner is operational
(2)Displays the malfunction code when
fault occurs.

Lights up during Timer operation.

5

EMERGENCY FUNCTION & AUTO-RESTART FUNCTION

If the remote controller fails to work or maintenance
necessary, proceed as following:

Open and lift the front panel up to an angle to reach
the emergency button.

For heating model, press the emergency button first
and the unit will operate in COOL mode. Press for a
second time within 3 seconds, and unit will operate in
HEAT mode. Press for third after 5 seconds, the unit
will turn off.

For cooling only models, press the emergency button
once, and the unit will operate in COOL mode. Press
again, the unit will turn off.

The emergency button is located on E-box cover
of the unit under the front panel.

The appliance is preset with an auto-restart function.
In case of a sudden power failure, the module will
memorizes the setting conditions before the power
failure. When the power restores, the unit will restart
automatically with the previous settings preserved
by the memory function.

front panel

Emergency
button

The shape and position of the emergency button
may be different according to the model, but their
function is the same.

6

REMOTE CONTROLLER

For ON/OFF models For inverter models

7

REMOTE CONTROLLER

Remote controller buttons

No.

1
2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

TIMER/SLEEP + ECO/DISPLAY

17

ECO/DISPLAY + HEALTH/CLEAN

Buttons Function

GENTLE WIND

MODE

(TEMP UP)

(TEMP DN)

FAN

I FEEL

I SET

TURBO

TIMER/SLEEP

ECO/DISPLAY

HEALTH/CLEAN

To turn on/off the air conditioner

To activate the function of Gentle wind.

To select the operation mode: AUTO, COOL, DRY, FAN, HEAT.

To increase the setting temperature, lengthen the time in TIMER setting.

To decrease the setting temperature, reduce the time in TIMER setting.

To adjust the air flow direction vertically(optional).

To adjust the air flow direction horizontally.

To adjust the fan speed: auto, mute, low, mid-low, mid, mid-hign, high. Turbo

To activate the function of I FEEL

To activate the function of I SET

To switch on/off the TURBO mode

To switch on/off the GENERATOR mode

To switch on/off the TIMER function and SLEEP mode

To switch on/off the ECO mode and LED display light

To switch on/off the HEALTH function and Auto Clean function..

To switch on/off the CHILL WIND and HOT WIND fucntion.

To switch on/off the CHILL WIND and HOT WIND fucntion.

18

The display and some functions of the remote control may vary according to the model.

The shape and position of buttons and indicators may vary according to the model, but their function is the same.

The unit confirms the correct reception of each button with a beep.

Certain functions may not be available for your air conditioner.

The batteries in remote controller must be recycled or disposed of properly.

( + )

To activate the function of Child Lock, press and buttons
together for more than 3 seconds.

8

REMOTE CONTROLLER

Remote controller DISPLAY, meaning of symbols on the liquid crystal display

No.

1

Symbols

Meaning

AUTO MODE indicator

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

or

(FLASH)

COOLING MODE indicator

DRY MODE indicator

FAN MODE indicator

HEATING MODE indicator

BATTERY indicator

TEMPERATURE/ CLOCK indicator

FLAP SWING (Air flow) indicator

MUTE indicator

FAN SPEED indicator

AUTO FAN indicator

TURBO indicator

CHILD LOCK indicator

I FEEL indicator

GENTLE WIND indicator

CHILL WIND indicator

17

18

19

20

21

22

23

24

25

ECO indicator

HEALTHY indicator

GENERATOR MODE indicator

TIMER indicator

SLEEP MODE indicator

HOT WIND indicator

DISPLAY LIGHT indicator

CLEAN function indicator

8 C heating function indicator

9

Replacement of Batteries

Remove the battery cover plate from the rear of the remote controller,
by sliding it in the direction of the arrow.
Install the batteries according the direction (+and -)shown on the Remote

Controller.
Reinstall the battery cover by sliding it into place.

Use 2 LRO 3 AAA (1.5V) batteries . Do not use rechargeable
batteries . Replace the old batteries with new ones of the same
type when the display is no longer legible.
Do not dispose batteries as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.

Recommendations for locating and using the remote controller holder (if present).
The remote controller be kept in a wall-mounted holder.

10