Page 1
Operating Instructions
IR BULLET
Operating Instructions
Operating Instructions
1/3” True Day&Night IR Vari-Focal
Water Resistant Camera
Before installing and using the camera, please read the
instructions thoroughly and retain them for reference.
Page 2
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION TO REDUCE THE RISK OF
ELECTRIC SHOCK.
DO NOT REMOVE COVER(OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SER-
This symbol is intended to alert the user to the presence
of noninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
!
operating and maintenance (servicing) instructions in
the literature accompanying the product.
VICE PERSONNEL.
!
Warning
To prevent fire or shock hazard, do not expose this appliance
to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Wiring methods shall be in accordance with the National Electric Code.
This product is manufactured to comply with
the CE and FCC Certificate standard.
2
Page 3
Contents
Precautions 4
Composition 5
Explanation of Accessories 5
Features 6
7 Name of Each Part
8 Installation
8 Camera installaton
9 Notes on installation and usage
9 Troubleshooting
10 Specifications
11 Dimension
3
Page 4
Precautions
Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers. There
are no user serviceable parts inside. Ask a qualified service
personnel for servicing.
Avoid facing the camera with direct sunlight.
Do not aim the camera at bright objects. Never face it with direct
sunlight or other extremely bright object. Otherwise blooming or
smear may be caused.
Do not use strong solvents or detergents.
Use a dry cloth to the camera when it is dirty. If it is hard to remove
the dirt on the camera, use a mild detergent and wipe it gently.
Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera
could be damaged by improper handling or storage.
Before operating, please check proper temperature, humidity and power source ratings.
Do not expose the camera in such conditions
shown below.
Do not use in a room or area filled with cigarette smoke, dust or gas.
4
Page 5
Composition
Confirm that the following parts are included:
Camera
L-Wrench
Instruction Manual
OPTIMUS
IR BULLET
OperaTIng InsTrucTIons
OperaTIng InsTrucTIons
OperaTIng InsTrucTIons
Driver
Service Monitor Cable
Screws
1/3” True Day&Night IR Vari-Focal
Water Resistant Camera
Before installing and using the camera, please read the
instructions thoroughly and retain them for reference.
Explanation for accessories
L Wrench - Unscrew and tighten bracket screw.
Driver - To control DC Iris Level and Service video port.
Screw - To firmly attach the bracket to the wall or ceiling.
Service Monitor Cable - Monitoring the display screen through portable
monitor to adjust the camera.
5
Page 6
Features
1/3” Sony Super HAD(Ex-view HAD) CCD
550 TV Lines (Color) and 580TV Lines (B/W) Resolution
Minimum Scene Illumination 0 Lux (with LED On)
IR range Distance up to 60m
Color & B/W Auto switchable by Photocell and Sensitivity
Built-in 18~50mm/F1.5
Day & Night Vary-Focal DC Auto Iris Lens
Externally Adjustable Focal Length & Focus with Lever
Externally Adjustable DC Iris Level
CDS Photocell Auto Switching IR-LED Control 42 LEDs
(On : 5 Lux / Off : 3 Lux)
Built-in Fan & Heater
Cable Managed Bracket
Service Monitor Output
Water Resistant (IP-66)
AC24V / DC12V
6
Page 7
Name of each part Installation
3
4
N
L
DC LEVEL
H
T W
1
2
1. ZOOM LEVER
2. FOCUS LEVER
3. FOCUS / ZOOM BOLT SCREW
4. DC LEVEL VOLUME SCREW CAP
5. SERVICE VIDEO PORT
6. BRACKET
5
6
PAN TILT ADJUSTMENT
Page 8
Camera Installation
Zoom and Focus Lever
Loosen the levers and adjust Zoom/Focus.
After controlling, tighten each lever.
1. Zoom Lever
- To widen the viewing angle, turn the “Zoom Lever” to “W”(Wide)
- To obtain a closer view, turn this Lever to “T” (Tele).
2. Focus Lever
- To adjust the Focus between “N” (Near) or “ ” (Far) until the
sharpest focus is achieved.
3. Focus / Zoom Bolt Screw
Be careful not to lose these small bolts/screws which should not
be touched in normal use.
4. DC Level Volume Screw Cap
Remove this screw Cap carefully. Retain it in a safe place
as it must be replaced to protect from water entering the camera body.
Beneath the Screw is the DC level adjustment Pot.
- For a bright screen, turn the DC level Pot slowly
towards “H” (counter-clockwise) with the driver provided.
- For a dark screen, turn it towards “L” (clockwise).
Then tighten the Screw Cap to protect water entering
5. Service Video Port
Unscrew the service monitor screw and attach the supplied service
monitor cable to adjust the display screen. After finishing the proper
adjustment,
6. Bracket
Loosen the Pan/Tilt bolts of the bracket to adjust the camera direction.
In reference to page 7.
detach the service monitor cable and screw back and tighten.
8 7
Page 9
Notes on installation and usage
1. Do not disassemble the camera.
2. Always handle the camera with care. Please avoid mechanical shock
or vibration, and take caution to prevent damages or make scratches
on the camera glass due to careless storage and/or handling.
3. Do not clean the camera body with strong abrasives or soaps. When
the camera becomes dirty, clean it with dry rugs. Take precaution to
use dedicated rugs to clean glass.
4. Please keep the camera in a cool area that is not exposed to direct
sunlight. Failing to do so can cause undesired effects on the product.
Troubleshooting
If you have trouble operating the camera, check the following
guides for the possible problem.
Nothing appears on the screen.
ㅡ>Check the power connection and video signal line connection.
ㅡ>Check the brightness level of DC Auto Iris volume of the camera.
The video image is not clear.
ㅡ>Check if the camera glass has dust on the surface.
Clean the camera glass with a clean cloth or brush.
ㅡ>Make sure that the screen is not exposed directly to a bright light.
Adjust the position of the camera if necessary.
ㅡ>Check if protective film of camera glass is removed.
The screen is dark
ㅡ>Adjust the brightenss feature of the monitor.
ㅡ>Check the brightness level of DC Auto Iris volume of the camera.
The screen does not properly display when IR LEDs work.
ㅡ>Check if the camera glass has dust.
Clean the camera glass with a clean cloth or brush.
If you cannot solve the problem with above guidelines,
please contact an authorized technician.
9
Page 10
Specifications
ITEM
Image Sensor
Effective Pixels
Scanning System
Scanning Frequency
Resolution
Shutter Speed
S/N Ratio
Sync. System
Min. Illumination
Video Output
Lens
Power Supply
Power
Consumption
Operating Temp
Operating Humidity
Dimension
NTSC
1/3” Interline transfer type color CCD (Sony)
768H x 494v (380K pixels) 752H x 582v (440K pixels)
525 Lines 2:1 Interlace 625 Lines 2:1 Interlace
15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
550 TVL(Color), 580TVL(B/W)
1/60 sec.
More than 48dB (AGC Off)
Internal
0 Lux with IR-LED (42pcs)
VBS 1.0 Vp-p (75 ohm Load)
18~50mm Day&Night Vari-Focal DC Auto Iris Lens (F1.5)
AC24V / DC12V + 10%
Normal : 250mA, Max : 900mA / DC12V
Normal : 4.8VA, Max : 20VA / AC24V
PAL
1/50 sec.
90% RH max
98mm( ) x 162.5mm( L )
10
Page 11
Dimension
98.0
111.6
190.0
162.5
104.8
11
Unit : mm
Page 12
1/3” True Day&Night IR Vari-Focal Water Resistant Camera
MADE IN KOREA
Loading...