Page 1
IR Dome Camera
Instruction Manual
VER.:1.0, NO.:040142
Page 2
1
Thank you very much for purchasing our product. Before operating this
product, please read this instruction manual carefully to ensure proper use.
1. Safety Precautious
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SER
V
ICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SER
V
ICE PERSONNEL.
Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems).
When in use, please avoid directly contacting the eyes and do not
touch the camera body, for it can be heated up to 70℃.
When installing the camera, please avoid pointing it directly to
paper or flammable materials.
The camera is normal to be heated up to 70℃, under operation.
Although the camera is provided with tempered glass, please
avoid all direct contact to eliminate contamination, and use cotton
balls dipped in cleaning alcohol to clean the window.
2. Description
This inbuilt Infrared Illuminator camera uses a high sensitive 1/3” interline
transfer Charge Coupled Device (CCD) Image Sensor, and all state circuitry,
which provides extremely long life and high reliability. Offers excellent image
quality and functions with low lag and high burn resistance. IR illuminator
module has power saving features, built-in with automatic light-source
control (CDS CONTROL)/ the infrared illuminator is activated automatically
(ON/ OFF) when the luminous intensity drops.
Highly resistant to shock and vibration, easy to install, it is an excellent
choice for your CCTV system.
Page 3
2
3. Feature
With built-in high quality CCD Camera and high performance
Infrared Illuminator modules.
Infrared Illuminator has effective range up to 20 meters and wide
angle at 20°/ 50°, also assists cameras in providing a clear image
when under completely dark area.
Infrared Illuminator has built-in 24 pieces 850nm wavelength
infrared Light-Emitting Diode.
Built-in Cds light-source sensor can automatically turn on/off the
infrared illuminator by detecting the light source of environment.
Wide angle lens permits three-axis camera movement (X-axis/
Y-axis/ Z-axis). Allows precise adjustment to any preferred angles,
and enables optimum beam angles.
4. Contents
Item Name of Part Quantity
1 IR Dome Camera 1
2 Appurtenance Bag 1
3 Round Head Screw 1
4 Fix Retaining Screws 2
5 Ancho
r
2
6 Manual 1
Page 4
3
5. Installation & Operation
(1) Please select the most suitable position on the wall or ceiling to install
the camera.
(2) Rotate the dome housing counterclockwise to remove it from the
mounting base (shown on figure 1).
(3) Set the mounting base onto the wall or ceiling and center it over
the mounting hole, using the two retaining screws for the main
body, supplied by the appurtenance bag (shown on figure 1).
(4) The unit has a factory installed back conduit entry and one may
adjust the cables to side conduit entry according to installation
requirement (shown on figure 2).
Figure 1
Page 5
4
(5) Once the picture appears on the monitor, open the cover, adjust
the lens wrench to “NEAR←→FAR”, get the zoom view that you
desire, and then adjust the focus wrench of the lens to obtain the
best picture. After adjustment, tighten both wrenches. (shown on
figure 3).
Figure 3
Figure 2
or
Page 6
5
Figure 4
(6) DIP Switch Setting (shown on figure 4).
z Flickerless Function
Set switch-OFF/ F.L. to Flicker to enable flickerless function, in
this mode, the switch-AES/ OFF is auto disabled.
z AGC-Hi/ AGC-Lo Function
Adjust the switch to AGC indicates AGC-Hi and OFF indicates
AGC-Low. This switch setting to High or Low of the AGC
maximum gain. AGC-Hi mode--The maximum AGC gain is
approximately 26dB. AGC-Lo mode--The maximum AGC gain
is approximately 16dB.
(7) BLC FUNCTION
Set Switch-OFF/ BLC to BLC to enable Back Light Compensation
(BLC) function.
Page 7
6
(8) For lens adjustment, move the camera body (some model types
limits the PCB board to180°rotational adjustment) and set the focus
by turning the lens to the left or right direction. When the camera
focus adjustment has been completed, rotate the dome housing
clockwise to secure it to the mounting base (shown on figure 5).
(9) Connect the Video Output to the monitor or other video device through
a 75 Ohms type coaxial cable. Connect the AC/ DC-Terminator with
power source (shown on figure 6).
Note! The inner parts may differ depending on the camera model type.
Figure 6
Figure 5
Page 8
7
6. Specification
According to the camera purchased, select and refer to the appropriate specification below:
Color Camera
Image Device
1/3” Color SONY
Super HAD
1/3” Color SONY
Hi-Res. Super HAD
Picture Elements
NTSC: 510¯492
PAL: 50 0¯582
NTSC: 768¯494
PAL: 75 2¯582
Resolution 380 TVL 470 TVL
Min. Illumination 0.2 Lux/ F2.0
0.05 Lux/ F2.0
(EX-View)
0.4 Lux/ F2.0
S/N Ratio More than 48 dB
Electronic Shutter NTSC: 1/60~1/100,000, PAL: /50~1/110,000
Gamma 0.45
Lens Furnished
Vari-Focal Lens f3.3~12mm/ F1.5~360, DC Drive.
Vari-Focal with ICR f3.3~12.0mm/ f1.6~360, DC Drive.
White Balance Auto
Gain Control Auto
Sync. System Internal
Video Output 1 Vp-p/ 75 Ohms
Infrared Luminary 24 pieces IR-LED, life: 6000hrs.
Wavelength 850 nm
Beam Spread Angle 20°/ 50°
Illuminate Distance 20M
Illuminator Active Limit 5Lux
Power Supply DC12V ±10%, DC12V/ AC24V
Power consumption
IR ON: 4.8W (max)/ IR OFF: 1.4W (max)
(Note: Design and specifications are subject to change without prior notice.)
Loading...