Taylor Freezer C820, C822 Operation Manual
Models C820 & C822
Auto Lift Grills
Original Operating Instructions
073739-M
9/23/10 (Original Publication)
(Updated 1/27/12)
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Service:
Parts:
Date of Installation:
Information found on data plate:
Model Number:
Serial Number:
Electrical Specs: Voltage Cycle
Phase
Maximum Fuse Size: Amps
Minimum Wire Ampacity: Amps
Part Number:
E September, 2010 Taylor
All rights reserved.
073739-M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1 To the Installer 1............................................
Installer Safety 1........................................................
Site Preparation 1.......................................................
Electrical Connections 1.................................................
Installation 2...........................................................
Installation of Cable Kit 2................................................
Ventilation and Clearance 2..............................................
Grease Disposal Container 2.............................................
Section 2 To the Operator 3...........................................
Section 3 Safety 4....................................................
Section 4 Operator Parts Identification 6...............................
C820 Exploded View 6..................................................
C822 Exploded View 7..................................................
Accessories 8..........................................................
Section 5 Important: To the Operator 9.................................
Table of Contents Model C820 & C822
Table of Contents - Page 2
Section 6 Operating Procedures 10.....................................
Daily Opening Procedures 10..............................................
Programming Menu Items 14..............................................
Loading Store Menu Items To USB 16......................................
Loading Menu Items From USB 17.........................................
Operating Procedures 19.................................................
Daily Cleaning Procedures 21.............................................
Section 7 Troubleshooting Guide 29....................................
Section 8 Parts List 33.................................................
Wiring Diagrams 41......................................................
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E September, 2010 Taylor (Original Publication)
(Updated January, 2012)
All rights reserved.
073739-M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Table of Contents Model C820 & C822
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Section 1 To the Installer
The following are general installation instructions.
For complete installation details, please see the
checkout card.
cause severe injuries.
Installer Safety
Site Preparation
This unit has many sharp edges that can
In all areas of the world, equipment should
be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.
S Only Taylor authorized service personnel
should perform installation and repairs on
the equipment.
S Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
S Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
S Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
The main power supply to the equipment
must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.
Review the area where the unit will be installed
before uncrating the unit. Make sure all possible
hazards to the user or equipment have been
addressed.
Electrical Connections
The grill is supplied with one power cord. Check the
data plate on the grill for voltage, cycle, phase and
electrical specifications. Refer to the wiring diagram
provided inside the protective control panel door at
the front of the grill for proper power connections.
The power connection is located behind the access
line cover on the front of the grill.
In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70-1987. The
purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.
Compliance therewith, and proper maintenance, can
result in an installation essentially free from hazard!
In all other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.
The Proper Wire Size and Branch Circuit
Overcurrent Device shall be selected according to
the data label information and in accordance with
CEC Part I 2006, Section 14-100(e)(i).
Note:Allrepairsmustbeperformedbyan
authorized Taylor Service Technician.
Model C820 & C822 To the Installer
1
FOLLOW YOUR LOCAL ELECTRICAL CODES!
Installation
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417-1) on both the
removable panel and the equipment's frame.
S Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source, must have an
all-pole disconnecting device with a contact
gap of at least 3 mm installed in the external
installation.
S Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
S Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed
cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to
relieve conductors from strain, including
twisting, at the terminals and protect the insulation of the conductors from abrasion.
This machine is designed for indoor use only.
DO NOT installthemachineinanarea
where a water jet could be used to clean or rinse the
machine. Failure to follow this instruction may result
in serious electrical shock.
This grill must be installed on a level
surface. Failure to comply may result in personal
injury or equipment damage.
Installation of Cable Kit
If the unit is permanently connected, the Cable Kit
must be installed. Flexible conduit must be used
when installing the appliance.
Ventilation and Clearance
To ensure proper operation of this appliance, it must
be installed so that the products of combustion are
efficiently removed.
After set up, do not store anything on top of
the grill. Failure to follow this instruction may result
in a fire hazard.
Grease Disposal Container
If the grill is not factory-equipped with grease
disposal containers, the store is required to provide
appropriate grease disposal containers in
accordance with NSF Standard 4 requirements.
2
Model C820 & C822To the Installer
Section 2 To the Operator
The grill you have purchased has been carefully
engineered and manufactured to provide
dependable operation.
This grill, when properly operated and maintained,
will produce a consistent quality product. Like all
mechanical products, it requires cleaning and
maintenance. A minimum amount of care and
attention is necessary if the operating procedures in
this manual are followed closely.
This Operator's Manual should be read
before operating or performing any maintenance on
your equipment.
It is strongly recommended that all
personnel responsible for the equipment's operation
and cleaning review these procedures for proper
training and assurance that no misunderstandings
exist.
Note: Warranty is valid only if the parts are
authorized Taylor parts, purchased from an
authorized Taylor Distributor, and the required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on equipment or parts if
non-approved parts or refrigerant were installed in
the machine, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by neglect or abuse.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its
use is completed, and cannot be disposed as
unsorted municipal waste.
The user is responsible for returning the product to
the appropriate collection facility, as specified by
your local code.
In the event you should require technical assistance,
please contact your local authorized Taylor
Distributor.
For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.
Model C820 & C822 To the Operator
3
Section 3 Safety
We, at Taylor Company, are concerned about the
safety of the operator when he or she comes in
contact with the grill and its parts. Taylor has gone
to extreme efforts to design and manufacture built-in
safety features to protect both you and the service
technician. As an example, warning labels have
been attached to the grill to further point out safety
precautions to the operator.
IMPORTANT - Failure to adhere to the
following safety precautions may result in
severe personal injury or death. Failure to
comply with these warnings may damage the
machine and its components. Component
damage will result in part replacement expense
and service repair expense.
To Operate Safely:
DO NOT operate the grill without reading
this Operator's Manual. This manual should be kept
in a safe place for future reference.
S Stationary appliances which are not
equipped with a power cord and a plug or
other device to disconnect the appliance
from the power source, must have an
all-pole disconnecting device with a contact
gap of at least 3 mm installed in the external
installation.
S Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
S Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed
cord, (Code designation 60245 IEC 57), installed with the proper cord anchorage to
relieve conductors from strain, including
twisting, at the terminals and protect the insulation of the conductors from abrasion.
Per IEC 60335-1 and its part 2 standards, “This
appliance is to be used only by trained personnel. It
is not intended for use by children or people with
reduced physical, sensory, or mental capabilities, or
lack of experience and knowledge, unless given
supervision or instruction concerning the use of the
appliance by a person responsible for their safety.”
Failure to follow the instructions below may
result in severe injury or death from electrocution:
S DO NOT operate the grill unless it is
properly grounded.
S DO NOT attempt any repairs unless the
power supply to the grill has been
disconnected (must be performed by an
authorized service technician).
S DO NOT operate the grill unless all service
panels are restrained with screws.
110504
IMPORTANT: DO NOT use a water jet or
spray excessive water on or anywhere near the
grill. Failure to follow this instruction may result in
serious electrical shock and cause permanent
electrical and mechanical damage to internal parts.
Failure to follow this instruction may result in:
S
S
S
destroying electrical components
4
serious electrical shock
burns from hot steam
liquid collecting inside the grill and
Model C820 & C822Safety
DO NOT use cold water or ice to cool the
upper platen or the lower cook surface. Failure to
follow this instruction may result in:
S
serious electrical shock
The grill must be pulled away from the wall
for thorough cleaning. Disconnect the tether to the
grill, located on the back panel of the unit. When
returning the grill to its original position, use extreme
caution to smoothly and slowly roll the grill backward
into place. Failure to do so may cause the grill to tip
and will cause severe equipment damage or
personal injury.
S
S
destroying electrical components
Failure to follow the instructions below may
result in severe burns from high temperatures:
burns from hot steam
liquid collecting inside the grill and
S DO NOT prepare or remove product without
proper equipment.
S DO NOT allow untrained personnel to
operate this grill.
S USE EXTREME CAUTION when cleaning
the grill.
Appropriate grill clearance must be
maintained from all combustible materials. Failure to
comply could result in a fire hazard.
Take caution to protect eyes, lungs, and all
parts of the body from potential harm when using
any chemical cleaner. Failure to follow this
instruction may result in a chemical burn.
DO NOT use any abrasives or cleaners
other than approved foodservice cleaners and
degreasers. Failure to comply may cause illness to
the consumer and may also damage grill surfaces.
NOTICE all warning labels that have been
attached to the grill to further point out safety
precautions to the operator.
This piece of equipment is made in America and has
American sizes on hardware. All metric conversions
are approximate and vary in size.
NOISE LEVEL: Airborne noise emission does not
exceed 70 dB(A) when measured at a distance of
1.0 meter from the surface of the machine and at a
height of 1.6 meters from the floor.
These instructions are valid only if the country code
symbol appears on the appliance. If the symbol does
not appear on the appliance, refer to the technical
instructions which give the necessary instructions for
adapting the appliance to the utilization conditions of
that country.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its
use is completed and cannot be disposed as
unsorted municipal waste.
The user is responsible for returning the product to
the appropriate collection facility, as specified by
your local code.
This grill must be installed on a level
surface. Failure to comply may result in personal
injury or equipment damage.
Model C820 & C822 Safety
For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.
5
Section 4 Operator Parts Identification
C820 Exploded View
ITEM
1 CAN A.-GREASE X73944
2 SLIDE-GREASE CAN LEFT 069936
3 PANEL-SIDE UPPER LEFT 073990
4 SCREW-10-32X3/8 SLTD TRUS 024298
5 SCREW 10-32 X 3/8 039381
6 PANEL-BACK-LOWER LEFT 073992
*7 KIT A.-GREASE SHIELD X78330-SER
8 PANEL-BACK-LOWER 069656
9 PANEL-SIDE UPPER RIGHT 073989
10 SLIDE-GREASE CAN RIGHT 069935
11 PANEL-SIDE-LOWER-RIGHT 073991
12 NUT-JAM 1-1/2-12 STEEL 073594
111110
DESCRIPTION PART NO.
Figure 1
6
ITEM DESCRIPTION PART NO.
13 CASTER-5" 7-5/8 STEM 078377
14 CASTER-GRILL 5" W/LOCK 073240
15 KIT A.-GRILL CONTROL X73474-SER
16 BUTTON-OPERATOR-RED 076011
17 SWITCH-ROCKER-DPST-10A 076989-WP
18 SCREW-4-40 X 5/8 SLTD RND 039508
19 PANEL A.-FRONT-LOWER X69660
20 COVER A.-USB 073809
**21 GUARD-LENSE 075288
22 BUTTON-OPERATOR-BLACK 076012
**23 LABEL-CONTROL PANEL 075699SYM3
* 1 KIT PER PLATEN
**INTERNATIONAL, ONLY
Model C820 & C822Operator Parts Identification
C822 Exploded View
Figure 2
ITEM
1 CAN A.-GREASE X73944
2 SLIDE-GREASE CAN LEFT 069936
3 PANEL A.-SIDE UPPER LEFT X72962
4 SCREW-10-32X3/8 SLTD TRUS 024298
5 SCREW 10-32 X 3/8 039381
6 PANEL-SIDE-LOWER-LEFT 073262
*7 KIT A.-GREASE SHIELD X78330-SER
8 PANEL-BACK-LOWER 073550
9 PANEL A.-BACK SERVICE X73546
10 PANEL A.-SIDE UPPER RIGHT X72965
11 SLIDE-GREASE CAN RIGHT 069935
12 PANEL-SIDE-LOWER-RIGHT 073261
DESCRIPTION PART NO.
Model C820 & C822 Operator Parts Identification
ITEM DESCRIPTION PART NO.
13 NUT-JAM 1-1/2-12 STEEL 073594
14 CASTER-5" 7-5/8 STEM 078377
15 CASTER-GRILL 5" W/LOCK 073240
16 KIT A.-GRILL CONTROL X73474-SER
17 BUTTON-OPERATOR-RED 076011
18 SWITCH-ROCKER-DPST-10A 076989-WP
19 SCREW-4-40 X 5/8 SLTD RND 039508
20 PANEL-FRONT-LOWER 073554
21 COVER A.-USB 073809
22 BUTTON-OPERATOR-BLACK 076012
* 1 KIT PER PLATEN
111110
7
Accessories
ITEM DESCRIPTION PART NO.
1 SHEET-RELEASE (BOX 9) 073442
*2 RETAINER-SHEET RELEASE
(RETENTION BAR)
**3 CLIP-RELEASE MATERIAL
W/TAB
4 SCRAPER-TEFLON WIPER 075887
110602
072845
072673
Figure 3
8
ITEM DESCRIPTION PART NO.
5 STRIP-REPLACEMENT 075888
***6 HOLDER-CLEANING 073736
***7 PAD-CLEANING 073737
8 CLEANER-STERA SHEEN 6
1QT/CS
* SHOWN PER PLATEN
** SHOWN PER PLATEN
(NOTE: EXTRA CLIPS ARE SENT WITH GRILL)
*** CONTACT YOUR LOCAL TAYLOR DISTRIBUTOR
TO PURCHASE CLEANING PAD AND HOLDER
073160
Model C820 & C822Operator Parts Identification
Section 5 Important: To the Operator
Figure 4
ITEM
1 RAISE BUTTON
2 STANDBY/COOK MODE BUTTON
3 MASTER POWER SWITCH
4 CLEAN MODE KEY
5 PROGRAM KEY
DESCRIPTION
Model C820 & C822 Important: To the Operator
ITEM DESCRIPTION
6 TEMPERATURE INDICATOR LIGHTS
7 POWER KEY
8 FUNCTION DISPLAY
9 MENU SELECT KEYS
10 USB COVER
110518
9
Section 6 Operating Procedures
The Models C820 and C822 have a 24” (610 mm)
cook surface.
The Model C820 has two upper platens and the
Model C822 has one upper platen. These grills are
capable of cooking a variety of products and feature
two cooking options.
These grills provide all of the features of a flat grill,
as well as the advantages of two-sided cooking.
Note: The two platen Model C820 has been
selected to illustrate the step-by-step procedures.
For grills equipped with less than two platens,
perform the following steps as appropriate for your
grill platen configuration.
Daily Opening Procedures
Step 1
Slide the release sheet retainer (retention bar)
through the hemmed end of the release material
sheet.
Figure 5
Step 2
Hook the release sheet retainer on the release
material shoulder screws at the top of the upper
platen.
Before operating the grill, the release material
sheets must be installed on the upper platens. The
release material sheets should be reversed and
rotated on a daily basis (black side vs. gray side.)
Perform the following steps for installing release
material sheets:
CAUTION: Make sure the grill is COOL
before attempting to install or remove release
material sheets.
Figure 6
110531
10
Model C820 & C822Operating Procedures
Loading...