Taylor-Dunn ET-015-00, ET-015-72, ET-015-74, ET-015-48 Operation, T Roubleshooting And Replacement Parts Manual

Page 1

Models Inlcuded: ET-015-00 72, Volt Direct Drive ET-015-72 72, Volt Direct Drive ET-015-74 72, Volt Chain Drive ET-015-48, 48 Volt Chain Drive

The Best Way

To Go

About Your

Business

Revision: B

MANUAL MZ-150-05

Operation, Troubleshooting and

Replacement Parts Manual

Serial Number Coverage:

Model Starting - Ending ET-015-00 103847 - 108472 ET-015-72 109240 - 134256 ET-015-74 118001 - Current Production ET-015-48 108591 - Current Production

Page 2

Page 3

or mechanical, including photocopying and recording, or any information storage or retrieval system without prior written permission of Taylor-Dunn® Mfg. unless such copying is expressly permitted by federal copyright law. Address inquiries to Reference Permissions, Taylor-Dunn® Mfg., 2114 W. Ball Road, Anaheim, CA 92804

For more information about this and other Taylor-Dunn® manuals, please write Taylor-Dunn®:

TAYLOR-DUNN SERVICE CENTER

Taylor-Dunn® Mfg.

2114 W. Ball Road

Anaheim, CA 92804

(Attn: Technical Writer)

Page 4

B2-48 With Dump Bed Option

B2-10 Ambulance

B2-48 with Steel Cab, Foldaway 4-Passenger Seat and Stake Sides

P2-50 30,000 Pound Tow Tractor

ET 3000

ET1-50 Full Size Truck

Page 5

Contents

Table of Contents

Introduction

About this manual .................................... 2

Who Should Read This Manual ............... 2

Responsibilities ........................................ 2

How To Use This Manual.......................... 3

Conventions ............................................................ 3

How to Identify Your Vehicle.................... 4

Taking Delivery of Your Vehicle ............... 5

Safety Rules and Operating Instructions

Standard Specifications* .......................... 2

Safety Rules and Guidelines.................... 3

Driver Training Program........................... 3

Driver Qualifications. .............................................. 3

Vehicle Controls ....................................... 4

1) Light Switch........................................................ 4

2) Windshield Wiper Switch. .................................. 4

3) Hour Meter. ......................................................... 4

4) Battery Status Gauge ......................................... 4

5) Turn Signal Lever. ............................................. 4

6) Hazard Lights. .................................................... 4

7) Speedometer ...................................................... 4

8) Start Switch. ....................................................... 4

9) Power Light. ....................................................... 4

10) Heater/Defrost Timer (optional). ....................... 4

11) Heater/Defrost Switch (optional). ...................... 4

Odometer / Trip Odometer ...................................... 5

Horn Switch ............................................................ 5

Shift Lever .............................................................. 5

Battery Disconnect ................................................. 5

Steering .................................................................. 6

Seat Interlock Switch .............................................. 6

1) Accelerator Pedal ............................................... 6

2) Foot Brake Pedal ................................................ 6

3) Park Brake, Hand ............................................... 6

Vehicle Operational Guidelines ............... 7

Safety Guidelines ................................................... 7

Starting: .................................................................. 7

While driving:.......................................................... 7

Loading and Unloading ........................................... 7

Towing Loads:......................................................... 7

Parking ................................................................... 8

Towing This Vehicle................................................ 8

Fuse Panel ................................................ 9

Fuse Panel ............................................................. 9

Charging your vehicle .............................. 10

Signet® Charger Operation, Model HB Series ....... 10

Signet® Charger Operation, Model HBS series ..... 10

Lestronic II® Charger Operation ............................. 11

New Battery Break in .............................................. 11

Charging Time ........................................................ 11

Storing / Returning to Service ................ 11

Storing Your Vehicle................................................ 11

Returning to Service ............................................... 11

Periodic Maintenance Checklist .............. 12

Daily Visual inspection:........................................... 13

Maintenance Guidelines for

Severe Duty Applications................... 13

General Maintenance

Maintenance Guidelines........................... 2

Troubleshooting Guide ............................ 3

Lubrication Chart...................................... 4

Front Axle Service

Inspect the Front Wheel Bearings and

King Pin .............................................. 2

Adjust Front Wheel Bearings.................. 3

Front Axle Removal and Installation ....... 4

Removal.................................................................. 4

Installation .............................................................. 4

Steering Component Service

Front End Alignment ................................ 2

Inspect Ball Joints .................................... 5

Adjust the Steering Gear .......................... 6

Replace the Ball Joints, Tie Rods, and

Drag Link ............................................ 7

Replacing the Drag Link ......................................... 8

Replacing the Tie Rod ............................................ 9

Center the Steering Gear.......................... 9

Repair the Steering Gear .......................... 10

Exploded View of Steering Gear ............................ 12

Transmission/Rear Axle Service

Adjust the Drive Chain ............................. 2

Check the Oil Level................................... 3

Change the Oil .......................................... 3

Drive Motor, Chain Drive .......................... 4

Remove .................................................................. 4

Install ...................................................................... 4

Rear Axle ................................................... 5

Remove and Install ................................................. 5

Replace the Axle Bearing........................................ 5

Chain Case ................................................ 6

Disassemble........................................................... 6

Assemble................................................................ 6

Differential Assembly (3rd Member) ........ 8

Disassemble........................................................... 8

Assemble................................................................ 9

Re-shimming the Pinion Housing............ 11

Exploded View .......................................... 12

Page 6

Table of Contents

Brake Service

Inspect the Service Brake ........................ 2

Front Disc Brake Pads ........................................... 2

Disc Brake Rotor .................................................... 2

Brake Shoes ........................................................... 3

Brake Drum ............................................................ 3

Inspect the Parking brake ........................ 4

Adjust the Service Brakes ........................ 4

Adjust the Parking Brake ......................... 5

Primary Adjustment ................................................ 5

Secondary Adjustment............................................ 5

Check Master Cylinder Fluid.................... 6

Bleed the Brake System ........................... 7

Flush the Brake System ........................... 9

Replace Rear Brake Shoes....................... 10

Motor Service

Inspecting the Motor Brushes ................. 2

Motor Inspection....................................... 2

Motor Removal and Installation ............... 4

Replacing the Brushes ............................. 5

Replacing the Bearings ............................ 6

Repairing the Commutator....................... 6

Service Limits ........................................... 7

Battery Service

Cleaning .................................................... 2

Testing....................................................... 3

Charging ................................................... 4

Watering .................................................... 5

Single Point Battery Watering System .................... 5

Replacing (6-volt batteries only).............. 6

Moist Charge Batteries ........................................... 7

Storage and Returning to Service ........... 8

Storage ................................................................... 8

Returning to Service ............................................... 9

Throttle Linkage

Throttle Linkage Adjustments.................. 2

Magnetic Module .................................................... 2

Pot Box module ...................................................... 3

Tires and Wheels

Tire Inflation.............................................. 2

Tire Inspection .......................................... 2

Replace the Tire/Wheel............................. 3

Replace the Tire (pneumatic) .................. 3

Repair the Tire (pneumatic)..................... 4

Replace the Tire (pneumatic) .................. 5

Electrical Troubleshooting

Symptoms: ................................................ 2

READ THIS FIRST ..................................... 3

Test Equipment Required: ...................................... 3

IMPORTANT NOTES and INSTRUCTIONS......... 3

Definitions:.............................................................. 4

Forward/Reverse Switch:........................................ 6

Throttle Module: ...................................................... 7

Motor Windings ...................................................... 8

Contactors .............................................................. 9

Contactor Negative Return ..................................... 10

Unusual Symptom

Troubleshooting Guide...................... 11

PLUGGING DIODE ............................................... 12

FREEWHEEL DIODE ............................................ 12

ISO ......................................................................... 13

Contactors .............................................................. 13

Wire Diagrams Illustrated Parts

Front Axle and Brake .................................. 2

Steering Linkage ......................................... 4

Steering Gear ............................................. 6

Steering Column ......................................... 6

Front Suspension........................................ 8

Transmission Chain Case ........................... 10

Transmission Differential Case ................... 12

Rear Axle.................................................... 14

Rear Brakes................................................ 14

Rear Suspension ........................................ 16

Drive Shaft ................................................. 16

Motor (direct drive) ..................................... 18

Motor Mount (direct drive)........................... 18

Motor (chain drive)...................................... 20

Brake Lines................................................. 22

Brake linkage (parking brake) ..................... 24

Instrument Panel (dash).............................. 26

Speed Control Panel ................................... 28

F&R Switch Assembly................................. 30

Miscellaneous Electrical.............................. 32

Miscellaneous Frame and Body .................. 33

Doors.......................................................... 34

Charger ...................................................... 36

Batteries ..................................................... 38

Decals ........................................................ 40

Seat Cushions and Deck............................. 42

Page 7

Appendixes

Appendix A: Special Tools ....................... 2

Appendix B: Suggested Torque Limits for

Standard Hardware............................. 3

Hardware Identification ............................ 3

Standard Head Markings ........................................ 3

Hex Bolts ................................................................ 3

Other Bolts ............................................................. 3

Hex Nuts................................................................. 4

Hex Lock Nuts (stover) ........................................... 4

Other Nuts .............................................................. 4

Suggested Torque Values (non-critical hardware) .. 5

Suggested Torque Values (critical hardware) ......... 6

Appendix C: Brake Lining Handling

Precautions......................................... 7

Table of Contents

Page 8

B2-48 With Stake Side Dump Bed Option

SC1-00 Stock Chaser

E4-55 Sit Down Tow Tractor

C4-25 Sit Down Tow Tractor

Page 9

Table of Contents

About this manual.........................................2

Who Should Read This Manual....................2

Responsibilities ............................................2

How To Use This Manual ..............................3

Conventions ..............................................................3

How to Identify Your Vehicle ........................4

Taking Delivery of Your Vehicle ...................5

Shown with optional stake sides

Introduction

Page 10

INTRODUCTION

ABOUT THIS MANUAL

RESPONSIBILITIES

The purchase of this vehicle shows a belief in high quality products manufactured in the USA. Taylor-Dunn®, a leading manufacturer of electric burden and personnel carriers since 1949, wants to be sure this vehicle provides years of reliable service. Please continue to read this manual and enjoy this high quality Taylor-Dunn® vehicle.

This manual is to serve as a guide for the service, repair, and operation of Taylor-Dunn® vehicles and is not intended as a training guide. Taylor-Dunn® has made every effort to include as much information as possible about the operation and maintenance of this vehicle.

Included in this manual are:

• Vehicle Description

• Safety Rules and Guidelines

• Operational Information

• Operator Responsibilities

• Owner Responsibilities

• Control Operation and Location Information

• Maintenance and Troubleshooting Information

• Standard Parts List

Of the Owner...

The owner of this or any Taylor-Dunn® vehicle is responsible for the overall maintenance and repairs of the vehicle, as well as the training of operators. Owners should keep a record of conducted training and maintenance performed on the vehicle. (OSHA Regulation, 29 CFR 1910.178 Powered Industrial Truck Operator Training).

Of the Operator...

The operator is responsible for the safe operation of the vehicle, preoperational and operational checks on the vehicle, and the reporting of any problems to service and repair personnel.

Of the Service Personnel...

The service personnel are responsible for the service and maintenance of the vehicle. At no time should a service person allow any untrained personnel to service or repair this or any Taylor-Dunn® vehicle. For the purposes of training, a qualified service person may oversee the repairs or services being made to a vehicle by an individual in training. At no time should an untrained individual be allowed to service or repair a vehicle without supervision. This manual is not a training guide.

Before servicing, operating, training or performing maintenance on this or any other Taylor-Dunn® vehicle, read the appropriate Taylor-Dunn® manual.

Each Taylor-Dunn® manual references the applicable models and serial numbers on the front cover.

Please, be aware of all cautions, warnings, instructions, and notes contained in this manual.

WHO SHOULD READ THIS MANUAL

This manual is intended for use by anyone who is going to operate, own, perform maintenance on, service, or order parts for this Taylor-Dunn® vehicle. Each person should be familiar with the parts of this manual that apply to their use of this vehicle.

Of the Passengers ...

The passengers are responsible to remain fully seated, keeping their hands, arms, and legs inside the vehicle at all times. Each passenger should be fully aware of the vehicle’s operation. All forms of recklessness are to be avoided. Do not engage in horseplay.

Page-2

Model B 2-10 shown withstake sides and steel cab with doors options

Page 11

INTRODUCTION

HOW TO USE THIS MANUAL

This manual is organized into five main sections:

INTRODUCTION

This section describes how to use this service manual and how to identify your vehicle.

Safety Rules and Operating Instructions

This section outlines the safety and operational issues, location and operation of controls, and the operational checks that are to be performed on this vehicle. It also includes various subjects that should be included in the operator and service training program.

Maintenance Service and Repair

This section gives specific information on the servicing of the vehicle and a schedule for maintenance checks.

Electrical and Charger Troubleshooting

This section identifies the troubleshooting procedures for testing the electrical system and battery charger.

Illustrated Parts

This section provides an illustrated view of various assemblies. The illustrations are accompanied by tables identifying the parts.

Conventions

Symbols and/or words that are used to define warnings, cautions, instructions, or notes found throughout this manual. Refer to the examples below.

A shaded box with the word “Warning” and the symbol above denotes a warning. A warning alerts the reader of a hazard that

may result in injury to themselves or others. Be sure to follow any instructions contained within a warning and exercise extreme care while performing the task.

A shaded box with and the word “Warning” and the symbol above denotes a warning. This warning alerts the reader of

a high voltage hazard that may result in injury to themselves or others. Be sure to follow any instructions contained within a warning and exercise extreme care while performing the task.

Model R 3-80 shown equiped with a cargo box and steel cab with doors options

A box with the word “CAUTION” and the symbol above denotes a caution and is used to inform the reader that property

damage may occur. Be sure to exercise special care and follow any instructions contained with in a caution.

Note: Alerts the reader to additional

information about a subject.

Model B 2-48 equipped with the Dump Bed option

Page-3

Page 12

INTRODUCTION

HOW TO IDENTIFY YOUR VEHICLE

This manual applies to vehicles with the same model and serial numbers listed on the front cover. These vehicles are designed for driving on smooth surfaces in and around facilities such as industrial plants,

nurseries, institutions, motels, mobile home parks, and resorts. They are not to be driven on public highways.

This vehicle is not designed to be driven on public roads or highways. It is available in maximum designed speed of 18 mph (48 volt) and 25 mph (72 volt). Do not exceed the maximum designed speed. Exceeding the maximum designed speed may result in steering difficulty, motor damage, and/or loss of control. Do not exceed locally imposed speed limits. Do not tow this vehicle at more than 5 mph.

This vehicle conforms to requirements for Type E vehicles as described in O.S.H.A. Standard Section 29 CFR

1910.178 (Powered Industrial Trucks) and with all applicable portions of the American National Standard for Personnel and Burden Carriers (ANSI B56.8).

The locations of the model and serial numbers are illustrated below:

Page-4

Page 13

INTRODUCTION

TAKING DELIVERY OF YOUR VEHICLE

Inspect the vehicle immediately after delivery. Use the following guidelines to help identify any obvious problems:

• Examine the contents of all packages and

accessories that may have come in separate packages with the vehicle.

• Make sure everything listed on the packing

slip is there.

• Check that all wire connections, battery

cables, and other electrical connections are secure.

• Check battery cells to be sure they are filled.

• Check the tire pressure, tightness of lug nuts,

and for any signs of damage.

Check the operation of each of the following controls:

• Accelerator

• Brake

• Parking Brake

• Key-Switch

• Forward/Reverse Switch

What To Do If a Problem is Found

If there is a problem or damage as a result of shipping, note the damage or problem on the bill of lading and file a claim with the freight carrier. The claim must be filed within 48 hours of receiving the vehicle and its accessories. Also, notify your Taylor-Dunn® dealer of the claim.

If there is a problem with the operation of the vehicle, DO NOT OPERATE THE VEHICLE. Immediately contact your local Taylor-Dunn® distributor and report the problem. The report must be made within 24 hours of receiving the vehicle and its accessories.

The only personnel authorized to repair, modify, or adjust any part of this or any Taylor-Dunn® vehicle is a factory authorized service technician.

The only personnel authorized to repair, modify, or adjust any part of this or any Taylor-Dunn® vehicle is a factory authorized service technician. Repairs made by unauthorized personnel may result in damage to the vehicles systems which could lead to an unsafe condition resulting in severe bodily injury and/or property damage. Unauthorized repairs may also void the vehicles warranty.

• Reverse Beeper (if equipped)

• Front Headlight Switch

• Steering Wheel

• Horn

Model B 2-10 Ambulance

Page-5

Page 14

TAYLOR -DUNN

Page 15

TABLE OF CONTENTS

Standard Specifications* ....................2

Safety Rules and Guidelines .............3

Driver Training Program ....................3

Driver Qualifications. ........................................... 3

Vehicle Controls ................................4

1) Light Switch ..................................................... 4

2) Windshield Wiper Switch. ................................ 4

3) Hour Meter. ...................................................... 4

4) Battery Status Gauge ....................................... 4

5) Turn Signal Lever. ........................................... 4

6) Hazard Lights. .................................................. 4

7) Speedometer ..................................................... 4

8) Start Switch. ..................................................... 4

9) Power Light. ..................................................... 4

10) Heater/Defrost Timer (optional). ................... 4

11) Heater/Defrost Switch (optional). .................. 4

Odometer / Trip Odometer ................................... 5

Horn Switch .......................................................... 5

Shift Lever ............................................................ 5

Battery Disconnect................................................ 5

Steering ................................................................. 6

Seat Interlock Switch ............................................ 6

1) Accelerator Pedal..............................................6

2) Foot Brake Pedal.............................................. 6

3) Park Brake, Hand............................................. 6

Vehicle Operational Guidelines..........7

Safety Guidelines .................................................. 7

Starting:................................................................. 7

While driving: ....................................................... 7

Loading and Unloading ........................................ 7

Towing Loads: ...................................................... 7

Parking .................................................................. 8

Towing This Vehicle ............................................. 8

Fuse Panel ........................................9

Fuse Panel ............................................................. 9

Charging your vehicle........................10

Signet® Charger Operation, Model HB Series .... 10

Signet® Charger Operation, Model HBS series .. 10

Lestronic II® Charger Operation ......................... 11

New Battery Break in ........................................... 11

Charging Time ...................................................... 11

Storing / Returning to Service...........11

Storing Your Vehicle ............................................. 11

Returning to Service ............................................. 11

Periodic Maintenance Checklist.........12

Daily Visual inspection:........................................ 13

Maintenance Guidelines for

Severe Duty Applications...............13

Safety Rules and

Operating Instructions

Page 16

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 2

STANDARD SPECIFICATIONS*

ITEM MODEL VOLTAGE SPECIFICATION

Occupancy Driver + 1-passenger

Dimensions 417 L x 157.5 W x 193 H Centimeters (164 L x 62 x 76 H Inches)

Turning Radius 534 Centimeters (210 Inches)

Dry Weight ET-150-00 1,045 kg (2,300 lbs) Including Batteries ET-150-48 1,163 kg (2,565 lbs)

Maximum Load 682 kg (1,500 lbs) Deck dimensions 157.5 W x 223.5 L Centimeters (62 W x 88 L Inches)

ET-150-72 1,268 kg (2,796 lbs) ET-150-74 1,268 kg (2,796 lbs)

Electrical System ET-015-00 72 Volt Twelve 220 Ah, 6 Volt, Lead Acid Batteries,Solid State Speed Control

Transmission ET-015-00 Direct Drive to Automotive Differential

Motor, DC ET-015-00 14.9 kW (20 Horse Power)

Brakes Rear Wheel Hydraulic Drum, Hand Operated Park Brake

Steering Automotive Steering 24:1

Tires 195/75 R14

Frame All steel tubular independent frame with Fiberglass Cab

Instrumentation Speedometer, Battery Status Guage, Power Light

Light Accessories Dual Headlight, Dual Tail/Brake Lights, Directional Signals

Charger ET-015-00 72Volt 230 Vac, 13 Amp, 60 Hz Built In, 25 Amp output (max)

ET-015-48 48 Volt Eight 220 Ah, 6 Volt, Lead Acid Batteries,Solid State Speed Control ET-015-72 72 Volt Twelve 220 Ah, 6 Volt, Lead Acid Batteries,Solid State Speed Control ET-015-74 72 Volt Twelve 220 Ah, 6 Volt, Lead Acid Batteries,Solid State Speed Control

ET-015-48 Transaxle Assembly, Chain Drive to Automotive Differential ET-015-72 Direct Drive to Automotive Differential ET-015-74 Transaxle Assembly, Chain Drive to Automotive Differential

ET-015-48 11.1 kW (15 Horse Power) ET-015-72 14.9 kW (20 Horse Power) ET-015-74 9.7 kW (13 Horse Power)

Front Wheel Hydraulic Disc

ET-015-48 48 Volt 115 Vac, 15 Amp, 60 Hz Built In, 25 Amp output (max) ET-015-72 72 Volt 230 Vac, 13 Amp, 60 Hz Built In, 25 Amp output (max) ET-015-74 72 Volt 230 Vac, 13 Amp, 60 Hz Built In, 25 Amp output (max)

This vehicle conforms to requirements for Type E vehicles as described in O.S.H.A. Standard Section

1910.178 (Powered Industrial Trucks) and with all applicable portions of the American National Standard for Personnel and Burden Carriers (ANSI B56.8).

* - Specifications are subject to change without notice.

Safety Rules

Page 17

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 3

SAFETY RULES AND GUIDELINES

It is the responsibility of the owner of this vehicle to assure that the operator understands the various controls and operating characteristics of this vehicle (extracted from the American National Standards Institute Personnel and Burden Carriers ANSI B56.8). As well as, following the safety rules and guidelines outlined in ANSI B56.8 and listed below.

These vehicles are designed for driving on smooth surfaces in and around facilities such as industrial plants, nurseries, institutions, motels, mobile home parks, and resorts. They are not to be driven on public highways.

These vehicles are not designed to be driven on public roads or highways. They are available in maximum designed speeds ranging from 18 to 25 mph. Do not exceed the maximum designed speed. Exceeding the maximum designed speed may result in steering difficulty, motor damage, and/ or loss of control. Do not exceed locally imposed speed limits. Do not tow this vehicle at more than 5 mph.

Refer to Vehicle Operational Guidelines, Safety

Guidelines section for important safety information

regarding operating this vehicle.

DRIVER TRAINING PROGRAM

According to ANSI B56.8, the owner of this vehicle shall conduct an Operator Training program for all those who will be operating this vehicle. The training program shall not be condensed for those claiming to have previous vehicle operation experience. Successful completion of the Operator Training program shall be required for all personnel who operate this vehicle.

The Operator Training program shall include the following:

• Operation of this vehicle under circumstances

normally associated with your particular environment.

• Emphasis on the safety of cargo and personnel.

• All safety rules contained within this manual.

• Proper operation of all vehicle controls.

• A vehicle operation and driving test.

Driver Qualifications.

Only those who have successfully completed the Operator Training program are authorized to drive this vehicle. Operators must possess the visual, auditory, physical, and mental ability to safely operate this vehicle as specified in the American National Standards Institute Controlled Personnel and Burden Carriers ANSI B56.8.

The following are minimum requirements necessary to qualify as an operator of this vehicle:

Read and follow all of the guidelines listed below. Failure to follow these guidelines may result in severe bodily injury and/or property damage.

Before working on a vehicle:

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

• Demonstrate a working knowledge of each control.

• Understand all safety rules and guidelines as

presented in this manual.

• Know how to properly load and unload cargo.

• Know how to properly park this vehicle.

• Recognize an improperly maintained vehicle.

• Demonstrate ability to handle this vehicle in all

conditions.

Safety Rules

Page 18

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 4

VEHICLE CONTROLS

1) Light Switch

The headlight switch is located on the left dash panel. Push the top of the switch to turn the lights on. Push the bottom of the switch to turn the lights off.

2) Windshield Wiper Switch.

The windshield wiper switch is located on the left dash panel. Push the top of the switch to turn the lights on. Push the bottom of the switch to turn the light off.

3) Hour Meter.

The hour meter is located to the left of the battery status indicator. It records the number of hours the vehicle has been in operation.

4) Battery Status Gauge

The battery status indicator is located on the left dash panel. The battery status indicator has a LED bar graph that indicates the relative state of charge of the battery. The top LED will light only when connected to a fully charged battery or after completing a charging cycle. Successive lower LED’s will light as the battery charge diminishes. When the second from the bottom LED flashes the battery energy status is in energy reserve and should be placed on charge as soon as possible. When the two bottom LED’s are alternately flashing the batteries are empty and the truck should be taken out of service and charged to avoid damaging the batteries. The BSI will reset to fully charged only after a complete charge cycle is completed. A complete charge cycle is defined as battery voltage exceeding 2.35 volts per cell for a minimum of 6 minutes.

5) Turn Signal Lever.

The turn signal lever is located on the left side of the steering column. Push the lever forward to activate the right turn signal and pull the lever back to activate the left turn signal.

6) Hazard Lights.

The hazard light switch is located on the left side of the steering column. The switch is a small tab. To activate the hazard lights, pull the tab out. To turn the hazard lights off, push forward or pull back the directional signal lever.

7) Speedometer

8) Start Switch.

A key-switch, located on the right center side of the instrument panel, turns on the vehicle. Rotate the key clockwise to turn the vehicle power on, counterclockwise to turn the vehicle power off.

The key-switch should be in the “OFF” position whenever the operator leaves the vehicle.

This switch is also designed to secure and disable the vehicle. The key can only be removed when the keyswitch is in the “OFF” position.

9) Power Light.

The power light will be on when the start switch is on.

10) Heater/Defrost Timer (optional).

Set the heater timer to the desired time for the heater to be on.

11) Heater/Defrost Switch (optional).

This switch has two positions. “HEAT” position turns on the heater element and fan. “FAN” turns on the fan only. NOTE: The heater requires a substantial amount of power from he batteries. Running the heater for extended periods will result in lower run time between charging.

Safety Rules

Page 19

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 5

Shift Lever

The forward and reverse shift lever is located between the seats. Push the shift lever forward to engage the forward direction. Pull the lever back to engage the reverse direction.

DO NOT SWITCH from forward to reverse or vice-versa while the vehicle is in motion. Make sure the vehicle is completely stopped before shifting.

The forward and reverse shift lever should be in the center “OFF” position, with the start switch off and the park brake set whenever the operator leaves the vehicle.

Battery Disconnect

The battery disconnect switch is located to the right of the driver seat. To disconnect the battery from the control system, push down on the knob. Pull up on the knob to reconnect the battery.

Odometer / Trip Odometer

VDO model speedometer only. The odometer and trip

odometer is an integral part of the speedometer and can be found just below center on the speedometer faceplate. In normal operating mode, the odometer displays total mileage or trip distance.

To toggle the display, depress and release the button

located at the bottom of the speedometer. Trip distance is indicated by a “t” at the left of the display.

To reset the trip distance to 0, depress and hold the

button for about 2 seconds.

Horn Switch

The horn switch is located in the center of the steering wheel. Depress the switch to sound the horn, release it to turn it off.

Safety Rules

Page 20

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 6

1) Accelerator Pedal

The accelerator pedal is located to the right of the brake pedal. It controls the speed of the vehicle and operates similar to the accelerator pedal in an automobile. Depress the pedal to increase speed and release the pedal to decrease speed.

2) Foot Brake Pedal

The foot brake pedal, is located to the left of the accelerator pedal, it is for operation with the right foot only. It works similar to the brake in an automobile. Applying pressure to the brake pedal slows the vehicle according to the amount of pressure applied. Relieving pressure from the pedal releases the braking action.

3) Park Brake, Hand

The parking brake is actuated with a hand lever, which is located on the floorboard. To set the parking brake, push down on the brake pedal and pull the lever back until it locks. To release the park brake, depress the foot brake pedal, and push the lever forward until it stops.

Steering

The steering wheel and steering system are similar to an automobile. To turn right, turn the steering wheel clockwise. To turn left, turn the steering wheel counterclockwise. If equipped with tilt steering, the release lever is located on the lower left of the steering column. Pull the lever up to reposition the steering wheel.

Seat Interlock Switch

A switch located under the driver's seat disables the power to the vehicle when the driver leaves the seat. The driver must be seated for the vehicle to operate.

Whenever the driver leaves the vehicle, the driver should turn the key-switch off, place the forward-offreverse switch in the center “OFF” position, and set the park brake.

The seat interlock switch is only one part of the vehicle safety system. The interlock switch should not be relied upon as the only safety feature used to disable or disengage this vehicle. Doing so could result in unexpected movement of the vehicle causing severe bodily injury and/or property damage.

Safety Rules

Page 21

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 7

VEHICLE OPERATIONAL GUIDELINES

Safety Guidelines

• Only qualified and trained operators may drive this

vehicle.

• Drive only on level surfaces or on surfaces having

an incline of no more than 10% (5.6 degrees).

• Drive slowly when making a turn, especially if the

ground is wet or when driving on an incline.

• This vehicle may overturn easily if turned sharply or

when driven at high speeds.

• Observe all traffic regulations and speed limits.

• Keep all body parts (head, arms, legs) inside this

vehicle while it is moving.

• Keep the vehicle under control at all times.

• Yield right of way to pedestrians, ambulances, fire

trucks, or other vehicles in emergencies.

• Do not overtake another vehicle at intersections, blind

spots, or other dangerous locations.

• Do not drive over loose objects, holes, or bumps.

• Yield right of way to pedestrians and emergencies

vehicles.

• Stay in your driving lane under normal conditions,

maintaining a safe distance from all objects.

• Keep a clear view ahead at all times.

Starting:

Perform all necessary vehicle preparation steps, inspections, or maintenance before operating this vehicle.

1. Make sure the forward-off-reverse shift lever is in the center “OFF” position.

2. Set the parking brake.

While driving:

• Slow down and sound the horn to warn pedestrians

or when approaching a corner or other intersection.

• No reckless driving.

• Do not drive this vehicle on steep inclines or where

prohibited.

• Immediately report any accidents or vehicle problems

to a supervisor.

Loading and Unloading

• Do not carry more than the maximum number of

passengers allowed for this vehicle.

• Do not exceed the cargo load capacity.

• Do not load cargo that can fall off.

• Be careful when handling cargo that is longer, wider,

or higher than this vehicle, be sure to properly secure all loads.

Towing Loads:

• Do not exceed the towing capacity of the vehicle.

• Do not exceed the load capacity of the trailer. Refer to documentation supplied with your trailer for information regarding load capacity of the trailer.

• Make sure all loads are securely tied down. Refer to documentation supplied with your trailer for information regarding attaching loads to the trailer.

• Do not back up when towing more than one trailer.

• Drive slowly when towing loads with a high center of gravity.

• When turning, be sure to allow for “corner cutting” of the trailer.

• Allow for longer stopping distances when towing heavy loads.

• Allow for longer stopping distances when driving down a grade.

3. Hold down the foot brake.

4. Rotate the Start switch to the “ON” position.

5. Place the forward-off-reverse shift lever in the desired direction of travel.

6. Release the parking brake.

7. Release the foot brake.

8. Slowly depress the accelerator pedal.

Safety Rules

Page 22

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 8

Parking

Before leaving the vehicle:

• Set the parking brake.

• Set the forward-off-reverse switch to the ` “OFF”

position.

• Rotate the start switch to the “OFF” position.

In addition:

• If parking this vehicle on an incline, turn the wheels

to the curb, or block the wheels.

• Do not block fire aisles, emergency equipment,

stairways, or exits.

Towing This Vehicle

To tow this vehicle, attach a tow strap to the front bumper tow-bar.

NOTE: If the vehicle is equipped with an automatic

electric brake, do not tow the vehicle with the drive wheels on the ground.

Use another driver to steer this vehicle while it is being towed. Be sure the driver uses the brakes when the towing vehicle slows or stops. Do not tow the vehicle faster than 5 m.p.h. or its maximum designed speed, whichever is lower.

If at all possible, this vehicle should be placed on a carrier, rather than towing.

Safety Rules

Page 23

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 9

FUSE PANEL

The fuse panel is located under the dash to the left of the steering column.

Fuse Panel

Standard fuses shown. Other fuses may be installed depending on options installed on vehicle.

20A headlights

15A Wiper and Horn

Safety Rules

Page 24

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 10

CHARGING YOUR VEHICLE

Explosive mixtures of Hydrogen gas are present within battery cells at all times. Do not work with or charge battery in an area where open flames (including gas furnace or water heater pilots), sparks, cigarettes, or any other sources of combustion are present. Always provide ample ventilation in rooms where batteries are being charged. Failure to do so may result in severe bodily injury and/or property damage.

Signet® Charger Operation, Model HB Series

The Signet® HB series chargers use a semiautomatic charging system. The charger will turn itself ON when the AC power cord is connected to the AC power source and turn itself OFF when the batteries are fully charged. Refer to the data plate on the charger for the voltage and type power required for the charger.

There is a series of LED’s on the faceplate of the charger that serve two functions:

1. Status of charge. The LED’s will display an approximate percent of charge during the charging cycle. Refer to the table below.

2. Error condition. All three LED’s flashing is an indication of a charging problem (charger will also be beeping). Refer to the

Charger Troubleshooting

section for information on error codes.

Typical Signet® Built In

Battery electrolyte is poisonous and dangerous. It contains sulfuric acid. Avoid contact with skin eyes or clothing. Wear rubber gloves and safety glasses while servicing batteries. DO NOT INGEST! This may result in severe bodily injury.

The key switch must be in the “OFF” position when charging the batteries. Failure to turn the key switch “OFF” may result in damage to the vehicles electrical system.

Signet® Charger Operation, Model HBS series

The Signet® HBS series chargers are fully automatic. The charger will turn itself ON when the AC power cord is connected to the AC power source and turn itself OFF when the batteries are fully charged. Once the charge cycle is complete, the charger will continue to monitor the batteries. If the battery voltage drops during storage, the charger will start a new cycle to keep the batteries fully charged.

Refer to the data plate on the charger for the voltage and type power required for the charger.

There is a series of LED’s on the faceplate of the charger that serve two functions:

1. Status of charge. The STATUS LED’s will display an approximate percent of charge during the charging cycle. Refer to the table below.

Typical Signet® HBS

Charging State

0 to 50% Blinking OFF OFF

50% to 75% ON Blinking OFF

75% to 100% ON ON Blinking

Cycle complete ON ON ON

LED1 LED2 LED3

Safety Rules

2. Error condition. The FAULT LED flashing is an indication of a charging problem (charger may also be beeping). Refer to the Charger Troubleshooting section for information on error codes.

Page 25

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 11

Lestronic II® Charger Operation

The Lestronic II® charger is a semi-automatic charging system. The charger will turn itself ON when the AC power cord is connected to the AC power source and turn itself OFF when the batteries are fully charged. Refer to the data plate on the charger for the voltage and type power required for the charger. When plugged in, the charger assumes that the batteries require charging and will charger for a minimum of approximately 4-hours. This charger should not be plugged in until the batteries are discharged beyond 50% or the batteries may be overcharged..

New Battery Break in

New batteries require a break in period of up to 40-cycles. The batteries will not have their full capacity during this break in period and may require longer charging times.

To obtain the maximum battery life:

Charge the batteries only after they reach a normal discharge as indicated on the Battery Status Indicator (BSI). Failure to follow this guideline could result in the batteries entering an overcharge state, which will reduce the life of the batteries. If you find it necessary to charge the batteries before they are completely discharged we recommend waiting until they are discharged a minimum of 25% to reduce the possibility of overcharging. Refer to Vehicle Controls in this section for information on how to read the BSI.

Do not discharge the batteries beyond a normal discharge as indicated on the BSI. Refer to Vehicle Controls in this section for information on how to read the BSI.

Check the battery electrolyte once a week. Do not charge the batteries if the battery electrolyte is low. Charging when the electrolyte is low will damage the batteries and shorten their life-span. Only authorized personnel should perform battery maintenance including maintaining the battery electrolyte level. Refer to Section Maintenance,

Service and Repair for battery maintenance

information. Do not interrupt the charging cycle. When the charger is

plugged in, allow it to turn off before disconnecting. Interrupting the charging cycle could lead to overcharging or discharging the batteries too deep. Both circumstances will shorten the life of the batteries.

Charging Time

Average charging time is 8 to 10-hours. The time required to fully charge your batteries will vary depending on:

• Capacity of the batteries, higher capacity requires

longer charge time.

• Output of the charger, higher output requires less

charge time.

• Depth of discharge, the deeper a battery is

discharged, the longer it takes to charge.

• Temperature, low temperatures require longer charge

time.

It is not unusual for charge times to exceed 15-hours, especially with new batteries.

Charging time is limited to 20-hours (HBS) or 18-hours (HB). A fault will occur if the charging time exceeds the 20-hour limit.

STORING / RETURNING TO SERVICE

Both storing your vehicle and returning it to service should only be performed by authorized personnel.

Storing Your Vehicle

• Clean the batteries, then fill and charge before

putting the vehicle in storage. Do not store batteries in a discharged condition.

• Lube all grease fittings.

• Clean, dry, and check all exposed electrical

connections.

• Inflate tires to proper pressure (if applicable).

• For extended storage, the vehicle should be elevated

so that the tires do not touch the ground.

If stored for a prolonged period, the batteries should be charged as follows:

Returning to Service

• Check the

battery’s state of charge and charge if required.

• Perform ALL

maintenance checks in the periodic checklist.

Storage

Temperature

(F)

Over 60 1

Between 40 and 60 2

Below 40 6

Charging Interval

(months)

• Remove any blocks from the vehicle and/or place

the vehicle down on to the ground.

• Test drive before putting into normal service.

Safety Rules

Page 26

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 12

PERIODIC MAINTENANCE CHECKLIST

Safety Rules

NOTE: A full page copy of the Periodic Maintenance Checklist is on the

Page 27

SAFETY RULES AND OPERATING INSTRUCTIONS

Page 13

Daily Visual inspection:

Tire condition and pressure. External frame damage (body). Operation of all lights and warning alarms and/or horns. Smooth and proper operation of all controls such as but not limited to:

• Accelerator pedal, Brake pedal, Steering, Parking brake, etc.

• Proper operation of all locking devises such as but not limited to:

• Tool box, Removable battery trays, Cargo box, Cab doors, etc.

• Proper operation of all interlocking switches such as but not limited to:

• Key switch, Seat interlock switch, Charger interlock switch, etc.

Inspect for leaking fluids or grease.

MAINTENANCE GUIDELINES FOR SEVERE DUTY APPLICATIONS

1. This maintenance checklist is based on the average application. If the vehicle is operated under “severe conditions”, service procedures should be conducted more frequently than specified. The frequency of service under severe conditions is determined by the use of the vehicle. The owner/ operator must evaluate the operating environment to determine the increase in maintenance frequency.

In addition, the whole vehicle should be inspected monthly for signs of damage. The damage must be repaired immediately.

The following list is meant as a guide and is not all-inclusive of a “severe duty” application.

• Extreme temperature.

• Bumpy, dusty, or ill maintained roads.

• Excessively wet areas.

• Corrosive or contaminated areas.

• Frequent loading of vehicle at/near capacity.

• Use on multiple shifts.

2. Any deficiencies found during an inspection should corrected before the vehicle is returned to service.

3. Battery water level should be inspected on a weekly schedule.

Safety Rules

Page 28

TAYLOR -DUNN

Page 29

Table of Contents

Maintenance Guidelines ...............................2

Troubleshooting Guide ................................3

Lubrication Chart ..........................................4

Model C 4-25 Tow Tractor

Model E 4-55 Tow Tractor

General Maintenance

Page 30

Maintenance, Service and Repair

Maintenance Guidelines

Periodic maintenance and service must be performed on this vehicle. Failure to complete these scheduled maintenance and service procedures can result in severe bodily injury and/or property damage. It is the owner and/or operators responsibility to insure that proper service and maintenance is performed on the vehicle, described in this manual.

Before starting any repairs:

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front or rear wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

Turn the Key switch OFF BEFORE disconnecting the batteries. Disconnecting the batteries with the key switch ON may corrupt the controller programming resulting in a fault code 1 (refer to the fault table in the troubleshooting section).

Read and follow all of the guidelines listed below. Failure to follow these guidelines may result in severe bodily injury and/or property damage.

• Avoid fire hazards and have fire protection equipment present in the work area. Conduct vehicle

performance checks in an authorized area where safe clearance exists.

• Before starting the vehicle, follow the recommended safety procedures in Section 2, “Safety Rules and

Operational Information.”

• Ventilate the work area properly.

• Regularly inspect and maintain in a safe working condition, brakes, steering mechanisms, speed and

directional control mechanisms, warning devices, lights, governors, guards, and safety devices.

• Inspect and maintain battery limit switches, protective devices, electrical conductors, and connections in

conformance with Taylor-Dunn’s® recommended procedures.

• Keep the vehicle in clean condition to minimize fire hazards and facilitate detection of loose or defective

parts.

• Do not use an open flame to check level or leakage of battery electrolyte.

• Do not use open pans of fuel or flammable fluids for cleaning parts.

• Only properly trained and authorized technicians should perform maintenance or repairs to this vehicle.

Page 2

Page 31

Maintenance, Service and Repair

Troubleshooting Guide

Symptom Probable Cause

Front End Out of Alignment

Steering Pulls in One Direction

Low Tire Pressure Dry Lube Points in Steering Linkage

Hard Steering

Excessive Steering Play

Lack of Power or Slow Operation

Abnormal Noise

Damaged King Pin/Ball Joint Low Tire Pressure Worn Ball Joints Mis-Adjusted or Worn Steering Gear Loose Steering Linkage Brakes or Parking Brakes Dragging Batteries Discharged or Defective Worn Drive Gears Front End Out of Alignment Defective Speed Control Worn Drive Gears or Bearings Worn Front /Rear Axle Bearings Loose Lug Nuts Motor Bearings Worn Rear Wheel Bearing and/or Gasket Failed

Oil Leak in Rear Bearing Area

Drive Over Filled

Brake Pedal Soft or Spongy Air in Brake Lines

Brake Worn (1/16" Wear Limit)

Brake Pedal Low

Braking Power Low

Note: This list is provided as a guide only. It is not all inclusive of causes that may result in a specific

symptom.

Brake Fluid Low Brakes Out of Adjustment Brake Worn (1/16" Wear Limit) Brake Pads Contaminated with Fluid Brake Pedal Linkage Binding Brakes Out of Adjustment Air in Brake Lines

Page 3

Page 32

Maintenance, Service and Repair

Lubrication Chart

Front Axle

Rear Axle

Note: Drive shaft only on

model ET-150-00

# Description Locations Lubricant Type

1 Steering Pivot 1 General Purpose Grease 2 Front Wheel Bearings 2 High Temperature Wheel Bearing Grease

3 Ball Joints 6 General Purpose Grease 4 Leaf Springs 8 General Purpose Grease 5 Drive Shaft universal Joint 2 General Purpose Grease (see note) 6 King Pins 2 General Purpose Grease 7 Chain Case Drain Plug 1 8 Drive Fill Plug 1 140 Weight Gear Oil 9 Drive Level Plug 1 -

10 Drive Drain Plug 1 -

Page 4

Page 33

TABLE OF CONTENTS

Inspect the Front Wheel Bearings and

King Pin........................................2

Adjust Front Wheel Bearings............3

Front Axle Removal and Installation ..4

Removal ................................................................ 4

Installation ............................................................ 4

Front Axle Service

Page 34

Maintenance, Service, and Repair

INSPECT THE FRONT WHEEL BEARINGS AND KING PIN

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

Always use a lifting strap, hoist, and jack stands, of adequate capacity to lift and support the vehicle. Failure to use lifting and support devices of rated load capacity may result in severe bodily injury.

NOTE: Refer to the Replace Front Wheel

Bearings section for information regarding

the replacement of the wheel bearings.

9. Lower the vehicle.

10.Reconnect the main positive and negative cables at the batteries.

11. Remove the blocks from behind the wheels.

12.Release the park brake and test drive the vehicle.

6. Raise the front of the vehicle and support with jack stands.

7. Grab the top and bottom of the tire/ wheel assembly. Feel for any movement or play while pulling and pushing on the top and bottom of the tire. Any movement or play is an indication of loose wheel bearings or king pin.

NOTE: Refer to the Adjust Front Wheel Bearings

section for information regarding the adjustment of the wheel bearings.

NOTE: If the king pin is loose, then refer to Replace

the King Pins and Bushings for

information regarding replacing the king pin bushings. There are no adjustments for the king pin or bushings.

8. Spin the wheel and listen for any grinding noise. Any grinding noise may be an indication of worn or damaged wheel bearings.

Front Axle Page 2

Page 35

ADJUST FRONT WHEEL BEARINGS

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

Maintenance, Service, and Repair

6. Raise the front of the vehicle and support with jack stands.

7. Remove the hub dust cap and cotter pin.

8. While rotating the hub, tighten the spindle nut to 30 ft-lbs. This seats the bearings.

9. Back off the spindle nut one flat until the hub turns, but is not loose.

10. Spin the wheel and listen for any grinding noise. Any grinding noise may be an indication of worn or damaged wheel bearings.

NOTE: Refer to the Replace Front Wheel

Hub with Dust Cap

Removed

Bearings section for information regarding

the replacement of the wheel bearings.

11. Install a new cotter pin.

12. Install the dust cap.

13. Lower the vehicle.

14. Reconnect the main positive and negative cables at the batteries.

15. Remove the blocks from behind the wheels.

16. Release the park brake and test drive the vehicle.

Front Axle

Page 3

Page 36

Maintenance, Service, and Repair

FRONT AXLE REMOVAL AND INSTALLATION

Removal

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Remove both front wheels. Refer to Tires and

Wheels section for information regarding

removing the front wheels.

8. Tie up or support the front axle so it can not fall out of the vehicle.

9. Disconnect the drag link ball joint or rod end from the steering knuckle or the steering gear pitman arm.

NOTE: Refer to the Replacing the Ball Joints

section for information regarding the removal of the ball joints or rod ends.

10.If equipped with front brakes, disconnect the hydraulic brake lines from the brake bodies.

11. Disconnect the front axle beam from the front springs and remove the axle from the vehicle.

Installation

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Install the front axle in reverse order of removal.

NOTE: Use all new cotter pins. NOTE: Refer to the Replacing the Ball Joints

section for information regarding the installing the ball joints or rod ends.

NOTE: Refer to Tires and Wheels section for

information regarding removing the front wheels.

8. Realign the front wheels. Refer to Steering

Component Service section for information

regarding realigning the front wheels.

9. If equipped with front brakes, bleed the brakes. Refer to Brake Service section for information regarding bleeding the brakes.

10. Lower the vehicle.

11. Reconnect the main positive and negative cables at the batteries.

12. Remove the blocks from behind the wheels.

13. Release the park brake and test drive the vehicle.

NOTE: In some configurations the front springs and

or shocks will have to be removed in order to remove the axle beam. Refer to section

Front Suspension for information

regarding removing the springs and shocks.

Front Axle Page 4

Page 37

TABLE OF CONTENTS

Front End Alignment..........................2

Inspect Ball Joints .............................5

Adjust the Steering Gear ...................6

Replace the Ball Joints, Tie Rods,

and Drag Link ................................7

Replacing the Drag Link ...................................... 8

Replacing the Tie Rod .......................................... 9

Center the Steering Gear...................9

Repair the Steering Gear...................10

Exploded View of Steering Gear ......................... 12

Steering Component Service

Page 38

Maintenance, Service, and Repair

FRONT END ALIGNMENT

This section will refer to two different types of ball joints. One type is has a grease fitting and a tapered shaft where it is fitted to the steering arm or pitman arm. The second type cannot be greased and has a straight shaft. See the illustrations to the right. Depending on the configuration of your truck, it may be equipped with one or both types of ball joints.

In this text: The first type has a grease fitting and will be referred to as a “Ball Joint.” The second type has no grease fitting and will be referred to as a “Rod End.”

Center the Steering

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

Ball Joint

Rod End

Do not drive the vehicle while the steering wheel or front wheels are tied in position. Driving the vehicle while the steering wheel or front wheels tied in the position may cause loss of control of the vehicle resulting in severe bodily injury and/or property damage.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Turn the front wheels so that they are in the straight ahead position and then tie off the wheels so that they cannot turn from the straight ahead position.

8. Disconnect the drag link from the pitman arm.

NOTE: Refer to Replace the Ball Joints section

for information regarding removing the ball joint or rod end from the drag link.

9. Center the steering gear and tie off the steering wheel so that it cannot rotate.

NOTE: Refer to Center the Steering Gear section

for information regarding centering of the steering gear.

10. At this point both the steering wheel and the front wheels should be tied up and held in position. If one or the other is not tied up then you must start from the beginning.

11. Loosen the ball joint clamps or the rod end jam nuts on the drag link.

NOTE: Remember the position and orientation of the

clamps.

Steering Page 2

Page 39

Maintenance, Service, and Repair

12. Adjust the drag link so that it can be easily inserted into the pitman arm.

13. Tighten the ball joint or rod end nut as specified below: Ball joint - 40-45 ft-lbs. Rod end - 20-25 ft-lbs.

14. If equipped with ball joints, position the ball joint clamps in their original location and orientation.

15. Tighten the ball joint clamps (28-32 ft. lbs.) or the rod end jam nuts on the drag link.

16. Untie the steering wheel and the front wheels.

17. Reconnect the main positive and negative cables at the batteries.

If the clamps are positioned so that they contact other components, it may result in steering failure and loss of control of the vehicle causing property damage and/or severe bodily injury.

18. Rotate the steering wheel from a full left turn to a full right turn and make sure that the ball joint clamps do not contact any other component.

19. Remove the blocks from behind the wheels.

20. Release the parking brake and test drive the vehicle.

Rotate the steering wheel from a full left turn to a full right turn and make sure that the ball joint clamps do not contact any other component. Clamps positioned so that they contact other components may result in steering failure and loss of control of the vehicle causing severe bodily injury and/or property damage.

Steering

Page 3

Page 40

Maintenance, Service, and Repair

Front wheel alignment

NOTE: It is recommended to center the steering

before aligning the front wheels. Refer to the

Center the Steering section for

information.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the rear wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

8. Using a piece of chalk, mark a line around the center of both front tires.

HINT: Hold the chalk on the center of the tire and

rotate the tire to mark the line.

9. Loosen the ball joint clamps or the rod end jam nuts on the tie rod.

NOTE: Remember the position and orientation of the

ball joint clamps.

10. Lower the front wheels to the ground and push the vehicle back and forth a few feet to settle the suspension.

Front Measurement

6. Raise the front of the vehicle and support with jack stands.

7. Turn the front wheels so that they are in the straight ahead position and tie off the steering wheel so that it cannot rotate.

Steering Page 4

Sleeve Clamps

Tie Rod

Rear Measurement

11. Measure the distance between the lines at the front of the tires.

12. Measure the distance between the lines at the rear of the tires.

13. Adjust the tie rod so that the distance at the front and rear of the tires is the same.

14. If equipped with ball joints, position the ball joint clamps in their original location and orientation.

15. Tighten the ball joint clamps (28-32 ft. lbs.) or the rod end jam nuts.

16. Untie the steering wheel.

17. Reconnect the main positive and negative cables at the batteries.

18. Remove the blocks from behind the wheels.

19. Release the parking brake and test drive the vehicle.

Page 41

Maintenance, Service, and Repair

INSPECT BALL JOINTS

NOTE: A set of ball joints and/or rod ends will wear

at the same rate. If a ball joint and or rod end is worn out, then all should be replaced as a set.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the rear wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Tie off the front wheels so that they cannot turn.

8. While watching the ball joints, rapidly rotate the steering wheel to the left and right.

9. If the ball joint housing moves up or down then the ball joint is worn out and should be replaced. Refer to section Replacing a Ball Joint for information regarding replacing ball joints.

10. Untie the front wheels.

11. Reconnect the main positive and negative cables at the batteries.

12. Remove the blocks from behind the wheels.

13. Release the parking brake and test drive the vehicle.

Steering

Page 5

Page 42

Maintenance, Service, and Repair

ADJUST THE STEERING GEAR

NOTE: In some vehicle configurations it may be

necessary to remove the steering gear to perform this procedure. Refer to Replace

the Steering Gear for information

regarding removing the steering gear.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Disconnect the drag link from the pitman arm.

NOTE: Refer to Replace the Ball Joints section for

information regarding removing the ball joint from the drag link.

8. Loosen the gear lash jam nut and the worm bearing adjuster jam nut.

9. Unscrew the gear lash adjuster all of the way to the stop.

10.Loosen the worm bearing adjuster and then tighten just enough to remove all end play from the input shaft and then an additional 1/8 turn more.

11. While holding the worm bearing adjuster so that it cannot turn, tighten the worm bearing adjuster jam nut.

12. Find the center position of the steering shaft: A. Turn the steering shaft all of the way in one

direction.

B. While counting the rotations, turn the steering

shaft all of the way in the opposite direction.

C. Turn the steering shaft 1/2 the number of turns

in the original direction.

13. While rotating the input shaft back and forth through its centered position, adjust the gear lash adjusting screw so that there is a slight drag as the steering gear is rotated through its centered position.

14. While holding the gear lash adjusting screw so that it cannot turn, tighten the gear lash adjusting screw jam nut.

15. Reconnect the main positive and negative cables at the batteries.

16. Remove the blocks from behind the wheels.

Steering Page 6

17. Release the parking brake and test drive the vehicle.

Page 43

Maintenance, Service, and Repair

REPLACE THE BALL JOINTS, TIE RODS, AND DRAG LINK

This section will refer to two different types of ball joints. One type is has a grease fitting and a tapered shaft where it is installed on the steering arm or pitman arm. The second cannot be greased and has a straight shaft. See the illustrations to the right. Depending on the configuration of your vehicle, it may be equipped one or both types of ball joints.

In this text: The first type will be referred to as a “Ball Joint.” The second type will be referred to as a “Rod End.”

NOTE: If a rod end or ball joint is worn out, we recommend

replacing all of the ball joints and/or rod ends as a set.

Replacing a Rod End

Rod End

Ball Joint

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Loosen the rod end jam nut or clamp on the steering sleeve.

Rod End

Steering Sleeve

Jam Nut

Rod End Nut

Steering Arm

11. Install the rod end into the steering arm. Tighten the rod end nut to 20-25 ft-lbs.

12. Realign the front wheels.

NOTE: Refer to the Steering section for information

regarding realignment of the front wheels.

13. Lower the vehicle.

14. Reconnect the main positive and negative cables at the batteries.

15. Remove the blocks from behind the wheels.

16. Release the park brake and test drive the vehicle.

8. Remove the rod end nut.

9. Remove the rod end from the steering arm.

HINT: Count the number of turns required to remove

the rod end from the steering sleeve. This will make it easier to realign the wheels.

10. Install the new rod end into the steering sleeve. Screw it into the sleeve the same number of turns counted in the previous step. Do not tighten the rod end clamp or jam nut at this time.

Steering

Page 7

Page 44

Maintenance, Service, and Repair

Replacing a Ball Joint

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

11. Install the new ball joint into the steering sleeve. Screw it into the sleeve the same number of turns counted in the previous step. Do not tighten the ball joint clamp at this time.

12. Install the ball joint into the steering arm. Tighten the ball joint nut to 40-45 ft-lbs. and install a new cotter pin.

13. Realign the front wheels.

NOTE: Refer to the Steering section for information

regarding realignment of the front wheels.

14. Lower the vehicle.

15. Reconnect the main positive and negative cables at the batteries.

16. Remove the blocks from behind the wheels.

17. Release the park brake and test drive the vehicle.

Replacing the Drag Link

The Drag Link is the linkage that connects the steering gear pitman arm to the steering knuckle. Refer to the illustration on the following page.

6. Raise the front of the vehicle and support with jack stands.

Cotter Pin

Ball Joint Nut

Steering Arm

Ball Joint

Clamp

Steering Sleeve

7. Loosen the ball joint clamp on the steering sleeve.

8. Remove the cotter pin and ball joint nut.

9. Using a pickle fork, remove the ball joint from the steering arm.

10.Remove the ball joint from the steering sleeve.

HINT: Count the number of turns required to remove

the ball joint from the sleeve. This will make it easier to realign the wheels.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Remove the ball joints or rod ends from the steering knuckle and pitman arm.

NOTE: Refer to the Replacing the Ball Joints

section for information regarding the removal of the ball joints or rod ends.

8. Remove the drag link as an assembly.

Steering Page 8

Page 45

Maintenance, Service, and Repair

9. Install in reverse order.

10. Realign the front wheels.

NOTE: Refer to the Steering section for information

regarding realignment of the front wheels.

11. Lower the vehicle.

12. Reconnect the main positive and negative cables at the batteries.

13. Remove the blocks from behind the wheels.

14. Release the park brake and test drive the vehicle.

Replacing the Tie Rod

The Tie Rod is the linkage that connects the two steering knuckles together. Refer to the illustration below..

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

11. Lower the vehicle.

12. Reconnect the main positive and negative cables at the batteries.

13. Remove the blocks from behind the wheels.

14. Release the park brake and test drive the vehicle.

CENTER THE STEERING GEAR

NOTE: The drag link must be disconnected from the

pitman arm or the pitman arm removed from the steering gear to perform this procedure. Refer to the appropriat section for details.

1. Remove the pitman arm.

2. Rotate the input shaft clockwise until it stops.

3. While counting the rotations, rotate the input shaft counter clockwise until it stops.

4. Rotate the input shaft clockwise 1/2 the rotations counted in the previous step.

5. Mark the input and pitman shaft in relation to the housing.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front of the vehicle and support with jack stands.

7. Remove the ball joints or rod ends from the steering knuckles.

NOTE: Refer to the Replacing the Ball Joints

section for information regarding the removal of the ball joints or rod ends.

8. Remove the tie rod as an assembly.

9. Install in reverse order.

10. Realign the front wheels.

NOTE: Refer to the Steering section for information

regarding realignment of the front wheels.

Steering

Page 9

Page 46

Maintenance, Service, and Repair

REPAIR THE STEERING GEAR

Disassembly

NOTE: The steering gear must be removed from the vehicle for this procedure. Refer to Replace the

Steering Gear section for information regarding removing the steering gear.

NOTE: The steering gear is packed with grease. Only perform maintenance on the steering gear in an

area that will contain any grease that may spill out of the steering gear when it is disassembled.

Refer to the illustration at the end of this section for a blown up view of the steering gear assembly.

1. Center the steering gear. A. Turn the steering shaft all of the way in one

direction.

B. While counting the rotation, turn the steering

shaft all of the way in the opposite direction.

C. Turn the steering shaft 1/2 the number of turns

in the original direction.

2. Remove the worm bearing adjuster locking ring and the worm bearing adjuster.

3. Remove the side cover/pitman shaft assembly by removing the three side cover bolts and then pulling the assembly out of the housing.

NOTE: The side cover/pitman shaft assembly

normally does not have to be disassembled.

4. Remove the worm shaft and ball nut assembly from the bottom of the housing.

5. Remove the worm shaft seal.

6. Remove the pitman shaft seal.

7. Remove the upper worm bearing and bearing cup from the housing.

8. The ball nut assembly consists of two sets of ball bearings that recirculate in two channels in the ball nut housing. The bearings may fall out once the bearing guides are removed. Be careful not to lose any of the bearings.

9. Remove the ball guide clamps, ball guides and all of the ball bearings.

10.Remove the ball nut from the worm shaft.

11. Thoroughly clean and inspect all parts for signs of corrosion, damage or wear and replace as required.

Steering Page 10

Page 47

Maintenance, Service, and Repair

Reassembly

1. Lightly lubricate all parts before reassembly.

2. Install a new worm shaft seal and pitman shaft seal into the housing.

3. Install the upper worm bearing cup.

4. Divide the ball bearing into two equal groups.

5. Position the ball nut onto the worm as shaft as shown in the illustration.

6. Insert the ball guides into the ball nut.

7. Insert each group of bearings into the ball guides.

NOTE: Do not rotate the worm shaft while installing

the bearings. This may cause one or more of the bearings to enter the crossover passage in the ball nut, causing improper operation.

8. Install the ball guide clamp.

9. Place the upper worm bearing on the worm shaft and install the worm shaft/ball nut assembly into the housing being careful not to damage the worm shaft seal.

10. Install the assembled worm bearing adjuster into the housing and tighten just enough to remove all play in the worm shaft.

11. Install, but do not tighten the worm bearing adjuster lock nut.

12. Rotate the worm shaft to center the ball nut in the housing.

13. Place a new gasket onto the housing and install the assembled pitman shaft/side cover onto the housing using two of the three mounting bolts.

14. Pack the steering gear with grease through the open side cover bolt hole and then install the bolt.

15. Adjust the steering gear.

NOTE: Refer to Adjust the Steering gear section

for information regarding adjusting the steering gear.

16. Once the adjustments are completed, make sure that the locking ring and jam nut are tight.

Steering

Page 11

Page 48

Maintenance, Service, and Repair

Exploded View of Steering Gear

Steering Page 12

Page 49

TABLE OF CONTENTS

Adjust the Drive Chain ......................2

Check the Oil Level ...........................3

Change the Oil ..................................3

Drive Motor, Chain Drive...................4

Remove ................................................................. 4

Install .................................................................... 4

Rear Axle ..........................................5

Remove and Install ............................................... 5

Replace the Axle Bearing ..................................... 5

Chain Case .......................................6

Disassemble .......................................................... 6

Assemble ............................................................... 6

Differential Assembly (3rd Member) ..8

Disassemble .......................................................... 8

Assemble ............................................................... 9

Re-shimming the Pinion Housing.......11

Exploded View ..................................12

NOTE: The model ET-015-00 and ET-015-72 has a

direct drive input to the rear axle. There is no drive chain primary reduction.

Service

Transmission/Rear Axle

Page 50

Maintenance, Service, and Repair

Page 2

ADJUST THE DRIVE CHAIN

NOTE: A small amount of oil may come out when the

drive motor mounting bolts are loosened.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Place a small oil drain pan under the chain case.

7. Loosen but do not remove the three drive motor mounting nuts.

8. Loosen the chain adjuster jam nut.

Tie the vehicle to an immovable object to prevent the vehicle from moving in forward or reverse. Failure to securely tie the vehicle may result in unexpected vehicle movement resulting in severe bodily injury or property damage.

10. Tie the vehicle in place so that it cannot move.

11. Reconnect the batteries.

Rotating parts, keep hands and loose clothing clear of all moving parts. Failure to keep clear of moving parts may result in severe bodily injury and/or property damage.

12. Close all safety interlock switches, turn the key On, place the forward-off-reverse switch in forward and fully depress the accelerator pedal.

13. Tighten or loosen the adjustment screw to obtain the minimum noise level.

9. Raise the drive wheels off of the ground.

NOTE: If there is less than 1/16” of threads left on

the adjustment screw (see illustration) then the drive chain has stretched beyond service limits and should be replaced. Refer to section Chain Case for information regarding replacing the drive chain.

14. Release the accelerator pedal, place the forwardoff-reverse switch in off, turn the key off and disconnect the batteries.

15. Untie the vehicle.

16. Tighten the adjustment screw jam nut and motor mounting nuts.

17. Wipe off any oil that may have come from behind the motor.

F2/F3 Transmission

18. Lower the drive wheels to the ground.

19. Reconnect the main positive and negative at the batteries, remove the blocks from the wheels, and test drive.

Page 51

Maintenance, Service, and Repair

Page 3

CHECK THE OIL LEVEL

NOTE: The oil level in the chain case is maintained

by the transmission. Oil is pumped from the 3rd member into the chain case housing. It is not necessary to check the oil level in the chain case.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Park the vehicle on a level surface.

7. Place a small oil drain pan under the drive housing.

CHANGE THE OIL

Wear protective gloves when working with petroleum lubricants. Repeated contact with petroleum lubricants can result in skin disorders.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

8. Remove the drive housing level plug.

9. A small amount of oil should come out. This indicates the correct oil level.

NOTE: If a large amount of oil comes out, then let it

drain to the proper level and replace the level plug.

If no oil comes out, then fill the drive to the proper level and replace the level plug.

Typical location of oil plugs. The actual location of the level plug will vary depending on your vehicles configuration. The model ET-015-00 and ET-015-72 does not have a chain case. An additional fill plug is located on top of the drive housing. NOTE: This illustration shows a pinion parking brake, the ET-150 is not equipped with this brake.

6. Place a large drain pan under the chain housing.

7. Remove the chain case drain plug and allow all of the oil to drain from the housing and then reinstall the drain plug

8. Place the drain pan under the drive housing.

9. Remove the drive housing drain plug and allow all of the oil to drain from the housing and then reinstall the drain plug

10.Remove the chain case fill plug and add 1-pint of oil.

11. Remove the drive housing fill plug and add 2quarts of oil.

NOTE: Refer to the Lubrication Chart for information

regarding the type of oil.

12.Replace all fill plugs.

NOTE: Dispose of waste oil in accordance with your

local regulations.

13.Reconnect the main positive and negative at the batteries, remove the blocks from the wheels, and test drive.

F2/F3 Transmission

Page 52

Maintenance, Service, and Repair

Page 4

DRIVE MOTOR, CHAIN DRIVE

Remove

NOTE: In most cases it is not necessary to

disassemble the chain case to remove the motor. If you find it necessary to disassemble the chain case, refer to Transmission section for information regarding disassembly of the chain case.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Remove the four motor wires.

7. Loosen the drive chain adjusting screw.

8. Remove the hardware holding the motor to the chain case backing plate.

Install

Do not allow the wheels to rotate after the motor has been removed. Allowing the wheels to rotate may result in the drive chain getting bound up with the drive sprocket, locking up the transmission. Should this happen, the chain may have to

1. Tie the chain up in position with mechanics wire as shown.

2. Slip the motor sprocket under the chain and rotate the motor so that the mounting plate goes into the threaded studs and remove wire(s) holding the chain.

3. Install the motor mounting hardware but do not tighten until the chain adjustment is complete.

4. Adjust the drive chain. Refer to Adjust the Drive

Chain for information regarding adjusting the

drive chain.

5. Connect the motor wires.

6. Reconnect the main positive and negative at the batteries, remove the blocks from the wheels, and test drive.

9. Lift the rear of the motor and rotate the motor so that the motor mounting plate clears the two threaded studs on the chain case backing plate and remove the motor from the drive.

Chain tied with mechanics wire

F2/F3 Transmission

Page 53

Maintenance, Service, and Repair

Page 5

REAR AXLE

Remove and Install

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the drive wheel off of the ground.

7. Remove the wheel assembly.

Replace the Axle Bearing

NOTE: The axle must be removed from the vehicle

to replace the axle bearing. Refer to section Rear Axle: Remove and Install for information regarding removing the axle.

NOTE: A 10-ton press is required to replace the axle

bearing.

NOTE: The axle bearing will be damaged when it is

removed.

The axle bearing retainer will be damaged when it is removed. Do not reuse the axle bearing retainer. Reinstalling the original bearing retainer may result in the axle falling out of the transmission resulting in severe bodily injury or property damage.

Old axle bearings may explode while being removed. Place a cage around the axle bearing that will contain all debris if the bearing explodes. Failure to place a cage around the axle bearing could result in severe bodily injury or property damage.

8. Place a small oil drain pan under the end of the axle housing.

9. Remove the four axle retaining bolts. Secure the brake assembly, do not let it hang by the brake hose.

10. Using a slide hammer, remove the axle from the axle housing.

11. Remove the bearing and axle seal from the housing.

12. Install the axle in reverse order using a new seal.

13. Reconnect the main positive and negative at the batteries, remove the blocks from the wheels, and test drive.

1. Place the axle in a press and remove the bearing and bearing retainer.

2. Lightly lubricate the axle shaft.

3. Install a new bearing and bearing retainer and press into place.

NOTE: Some axle configurations have an

o-ring around the axle bearing. The bearing should be orientated so that the o-ring is farthest away from the axle hub. See the illustration below.

F2/F3 Transmission

Page 54

Maintenance, Service, and Repair

Page 6

CHAIN CASE

NOTE: Some vehicle configurations may require that

the transmission be removed to disassemble the chain case. Refer to section

Transmission Assembly for information

on removing the transmission.

Disassemble

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Place an oil drain pan under the chain case.

7. Remove the chain case drain plug and allow all of the oil to drain from the housing and then reinstall the drain plug

8. Remove the brake drum. Refer to section

Brakes: Replace the Brake Drum for

information regarding removing the brake drum.

9. Remove the nuts from the three threaded studs at the small end of the chain case housing.

10.Remove the chain case housing bolts, brake assembly, and alignment brackets.

11. Remove the chain case housing from the backing plate.

12.Remove the pinion seal from the chain case housing.

Typical Chain Case

Pinion brake shown is not used on the ET-150

Assemble

1. Thoroughly clean all gasket surfaces.

2. Apply a 1/8” bead of 94-430-03 gasket sealer to the face of the 3rd member.

3. Install the backing plate to the 3rd member. Torque to 30-45 ft-lbs.

4. Install the motor to the backing plate. Do not fully tighten the motor mounting hardware at this time.

5. Install the motor sprocket, drive sprocket and chain. Do not adjust the chain tension at this time.

6. Apply a 1/8” bead of 94-430-03 gasket sealer to the chain case housing.

13.Loosen the motor mounting bolts.

14.Loosen the chain adjuster.

15.Remove the drive chain, motor nut and sprocket and the drive sprocket.

16.If the backing plate must be removed from the 3rd member, first remove the motor from the backing plate then remove the backing plate from the 3rd member.

F2/F3 Transmission

Apply sealer around the ID of the holes

7. Install the chain case centering tool (refer to Appendix A) into the pinion seal bore in the chain case housing.

Page 55

Page 7

Woodruf Key

Maintenance, Service, and Repair

Motor

Adjusting screw

3rd Member

Nut

Washer

Mounting Plate

Washer

Nut

Chain Case Housing

Nut

Backing Plate

Bolt

O-Ring

Motor Sprocket

Nut

Spacer

Drive Sprocket

Drive Chain

Bolt

Drain Plug

8. Install the chain case housing onto the pinion shaft and tighten the pinion nut to 75 ft-lbs.

9. Install and tighten the three nuts and washers to the threaded studs and the housing bolts that are not used for the brake mounting bracket or alignment brackets.

10.Remove the centering tool and install a new pinion seal. Lightly lubricate the pinion seal lip.

11. Install the brake assembly and the brake band alignment bracket(s). Do not tighten the bolts at this time.

12.Install the brake drum. Torque to 175 ft-lbs.

13.Tighten the brake adjusting bolt to 25 ft-lbs.

14.Tighten the brake assembly mounting bolts.

15.Adjust the brake. Refer to section Brake

Service: Adjust the Brakes for information

regarding adjusting the brakes.

16.Adjust the drive chain. Refer to section Adjust

the Drive Chain for information regarding

adjusting the drive chain.

F2/F3 Transmission

Page 56

Maintenance, Service, and Repair

Page 8

DIFFERENTIAL ASSEMBLY (3 MEMBER)

Disassemble

NOTE: Bearings and races must be replaced as a

set. If any one bearing or race is worn, its mate must also be replaced. It is recommended to replace all bearings and races in the 3rd member as a set.

1. Drain the oil from the differential housing and chain

case. Refer to section Change the Oil for information regarding draining the oil.

2. Remove the transmission assembly from the

vehicle. Refer to Transmission Assembly:

Remove and Install for information regarding

removing the transmission.

3. Remove both rear axle assemblies. Refer to

section Rear Axle: Remove and Install for information regarding removing the axles.

4. Remove the chain case and backing plate from

the 3rd member. Refer to section Chain Case:

Disassemble for information regarding removing

the chain case.

5. Remove the nuts holding the 3rd member to the axle housing and remove the 3rd member from the housing.

6. Install a spacer on the pinion shaft so that the pinion nut can be installed and tightened.

7. While rotating the pinion shaft, tighten the pinion nut to 100 ft-lbs.

8. Measure and record the ring and pinion gear backlash. This setting will be used during reassembly.

9. Remove the pinion housing and pinion gear from the 3rd member.

NOTE: Do not lose the spacers and shims in the

pinion housing or the pinion housing shim(s).

10. If required, remove the rear tapered bearing from the pinion shaft and discard.

NOTE: Do not remove the bearing unless it requires

replacement. Removing the rear bearing will damage the bearing. Replacing this bearing will require re-shimming of the pinion shaft.

11. If required, remove the bearing races from the pinion housing.

12. Mark the differential bearing caps and 3rd member housing so that they can be reassembled in their original location. Refer to illustration at end of section.

NOTE: The caps cannot be interchanged or replaced.

If the caps are lost or damaged then the entire 3rd member assembly must be replaced.

13. Remove the differential bearing caps, bearing adjusting nuts and races.

14. Remove the differential assembly from the 3rd member.

15. Mark the ring gear and differential housing so that the ring gear can be reinstalled in the same orientation.

F2/F3 Transmission

Measuring backlash

16. Remove the bearings from the differential housing and discard.

NOTE: Removing the bearings will damage the

bearings. Do not remove the bearings unless they require replacement.

17. Remove the ring gear from the differential housing.

18. Remove the differential shaft locking roll pin.

19. Split the 2-piece differential housing.

20. Drive the differential pinion shaft out of the housing with a brass drift punch.

21. Remove the differential gears, axle gears, and thrust washers.

Page 57

Maintenance, Service, and Repair

Page 9

Assemble

NOTE: Thoroughly clean and inspect all parts before

reassembly. Apply a small amount of differential oil to all gears and bearings before reassembly.

NOTE: Depending on your vehicle config-uration, the

rear pinion pilot bearing is not required and may not be installed.

NOTE: If the ring and pinion gear set is to be replaced

then the shims for the pinion housing may have to be adjusted. Refer to section

Selecting the Pinion Housing Shim for

information on adjusting the shim.

NOTE: Most of our gear sets are non-hunting or semi-

hunting gears. With this type of gear the pinion and ring gears must be aligned correctly. There will be two teeth marked on the ring gear and one tooth marked on the pinion gear. The one tooth on the pinion gear must be installed so that it is between the two teeth on the ring gear. The gear ratios are; 2.50, 2.70, 2.75, 3.25 and 3.00.

Pinion housing

1. If the rear pinion bearing was removed, install a new bearing.

2. Install the bearing races into the pinion housing.

3. Place the pinion gear into the 3rd member.

4. Install the pinion housing onto the 3rd member.

5. Install the pinion bearing spacers, shims and front bearing.

6. Install a spacer on the pinion shaft so that the pinion nut can be installed and tightened.

7. While rotating the pinion shaft, tighten the pinion nut to 100 ft-lbs.

8. Check the torque required to rotate the shaft. If the torque is not between 6 -10 in-lbs. then the bearings must be re-shimmed. Add or subtract shims as required until the torque is within specifications.

Differential Assembly

9. Reassemble the differential housing in reverse order.

10. Place the ring gear onto the differential housing matching the mark made during disassembly.

11. Install two of the ring gear bolts finger tight to align the gear.

12. Press the ring gear onto the differential housing.

13. Install the ring gear bolts and cross tighten to 6580 ft-lbs.

14. If the differential bearings were removed, install new bearings.

15. Place races onto the differential bearings and place the differential assembly onto the 3rd member. Position the assembly so that it is just touching the pinion gear.

16. Install the bearing adjusting nuts making sure that the nuts are not cross threaded. Position the nuts so they are in contact with the bearing races.

F2/F3 Transmission

Page 58

Maintenance, Service, and Repair

Page 10

Cross threading the nuts will damage the 3rd member housing and bearing caps. If the housing and/or nuts are damaged, the entire 3rd member assembly may have to be replaced.

17.Install the bearing caps in their original locations and torque the bolts to 12-15 ft-lbs. making sure that the adjusting nuts still turn freely.

NOTE: In the following procedure, "Left adjusting nut"

refers to the nut on the ring gear side of the differential assembly. "Right adjusting nut" refers to the nut on the pinion gear side of the differential assembly.

NOTE: Be sure to continually rotate the ring gear while

adjusting the bearings. This makes sure that the bearings and races remain seated correctly.

NOTE: One hole on adjusting nut = approximately

0.003" change in backlash. Left and right nuts MUST be turned the same amount AND in the same direction. The final direction of rotation MUST be in the tightening direction, to loosen a nut 1-hole, back off 2-holes and then tighten 1 hole. The ring gear should be rotated any time the nuts are being adjusted.

18. Loosen the right side nut.

19. Tighten the left nut until all backlash is removed from the ring and pinion gear.

20. Tighten the right nut until a case spread of 0.010” is indicated on the dial indicator.

NOTE: If new ring and pinion gears are used, refer to

the recommended backlash that is supplied with the gear set

21. Measure the backlash. If the backlash is not within

0.002” of the original measurement taken on disassembly or the recommended setting for new gears, then readjust the bearings as follows:

The differential bearing preload is set by measuring the case spread of the 3rd member housing. As the bearing adjusting nuts are tightened, the two differential bearing caps will be pushed (spread) away from each other. A dial indicator must be used to measure the case spread as the nuts are tightened. Mount the dial indicator so that it is 4 inches above the top of the bearing caps and parallel to the center line of the carrier bearings.

To increase backlash, loosen the left spanner nut and then tighten the right spanner nut the same amount.

To decrease backlash, loosen the right spanner nut and then tighten the left spanner nut the same amount.

22. Apply gear marking compound on both sides of 7 to 10 teeth on the ring gear.

23. While applying resistance to the pinion shaft, rotate the ring gear back and forth (not full revolutions) until a clear contact pattern is shown. Compare the contact pattern to the illustration on the following page and reshim the pinion housing or adjust the backlash as indicated on the illustration . If the pinion housing is reshimed the backlash must be reset. Go back and repeat ALL procedures in setting the backlash.

24. Tighten the bearing cap bolts to 70-85 ft/lbs (F2 drive), 55-70 ft/lbs (F3 drive) and install the spanner nut locks. Tighten the spanner nut lock bolts to 12-25 ft/lbs.

NOTE: Final pinion nut torque on completely

assembled drive, 175 ft/lbs.

F2/F3 Transmission

Page 59

Maintenance, Service, and Repair

Page 11

RE-SHIMMING THE PINION HOUSING

The pinion housing shim may require replacement if the ring and pinion gear or pinion housing is replaced. Pinion housing shims are available from 0.005” to 0.021” in increments of 0.001”. Locate the number printed on the

flat surface of the pilot bearing shaft of the pinion gear. It should be a number ranging from -5 to +5. This is the amount in 0.001” increments to add to the “standard” shim. For example, if the number on the shaft is ‘-3’ then the standard shim (0.015) plus ‘-3’ equals 0.012. The correct shim would be 0.012”.

If you cannot locate the number on the shaft, start with the standard shim and adjust as required per the contact pattern chart below.

F2/F3 Transmission

Page 60

Maintenance, Service, and Repair

Page 12

EXPLODED VIEW

F2/F3 Transmission

Page 61

TABLE OF CONTENTS

Brake Service

Inspect the Service Brake .................2

Front Disc Brake Pads .......................................... 2

Disc Brake Rotor .................................................. 2

Brake Shoes .......................................................... 3

Brake Drum .......................................................... 3

Inspect the Parking brake ..................4

Adjust the Service Brakes .................4

Adjust the Parking Brake ...................5

Primary Adjustment .............................................. 5

Secondary Adjustment .......................................... 5

Check Master Cylinder Fluid .............6

Bleed the Brake System ....................7

Flush the Brake System ....................9

Replace Rear Brake Shoes ...............10

Page 62

Maintenance, Service, and Repair

INSPECT THE SERVICE BRAKE

Front Disc Brake Pads

Current Taylor-Dunn® brakes are asbestos free. However, there is the possibility that the original brakes were replaced with aftermarket parts containing asbestos. Since this possibility exists, all brake parts should be handled as if they contain asbestos. Refer to Appendix C for recommended handling precautions.

NOTE: The brake pad must be removed to accurately

measure the lining thickness. Refer to Replace

the Front or Rear Brake Pads section for

information on removing the brake pads.

Measure the brake pad lining at the thinnest point on the pad. If the brake pad lining is 1/16-inch or less then the brake pad must be replaced.

It is recommended to replace the left and right side brake pads as a set.

Disc Brake Rotor

Rotor Service Limit = The minimum rotor thickness

will be stamped in the rotor. See example below.

NOTE: The front brake rotor is an integral part of the

front hub. If the brake rotor is worn beyond its service limits, then the front hub must be replaced. Refer to Front Axle Service for information on replacing the front hub.

NOTE: The wheel must be removed to accurately

measure the rotor thickness. Refer to Tires

and Wheels section for information on

removing the wheel.

1. Measure the run out of the rotor at its maximum diameter. If the run out exceeds 0.005, then the rotor must be machined. Do not machine the rotor beyond its service limit (see above).

NOTE: A bent axle or damaged rear axle could cause

excessive brake rotor run out.

2. Measure the thickness of the brake rotor in 3 places. If the any one of the measurements is less than the rotor service limit , then the rotor must be replaced.

Do not use a rotor that is worn beyond its service limits. A rotor worn beyond its service limits could fail and cause loss of brakes resulting in severe bodily injury and/or property damage.

Brakes Page 2

Rotor Service Limit (example only, refer to actual rotor for specification)

Page 63

Maintenance, Service, and Repair

Brake Shoes

NOTE: The wheel must be removed to accurately

measure the brake shoes. Refer to Tires and Wheels section for information on removing the wheel.

Measure the brake shoe lining at the thinnest point on the shoe. If this is 1/16-inch or less then the brake shoe must be replaced.

NOTE: If this is a riveted lining, then the measurement

must be to the top of the rivets.

It is recommended to replace the left and right side brake shoes as a set.

Brake Drum

Drum Service Limit = The minimum drum inner

diameter will be stamped in the drum. See example below.

NOTE: The wheel must be removed to accurately

measure the brake drum. Refer to Tires and Wheels section for information on removing the wheel.

If the brake drum is grooved or worn beyond the service limit then the brake drum must be replaced.

Measure the inside diameter of the brake drum in 3places.If the difference between any of the measurements exceeds 0.010-inches then the brake drum must be resurfaced or replaced.

Do not use a brake drum that is worn beyond its service limits. A drum worn beyond its service limits could fail and cause loss of brakes resulting in severe bodily injury and/or property damage.

Brake Drum Service Limit (example only, refer to actual

drum for specification)

Brakes

Page 3

Page 64

Maintenance, Service, and Repair

INSPECT THE PARKING BRAKE

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Release the park brake.

7. Inspect the brake shoes. The parking brake shoes are the same as the service brake shoes. Refer to Inspect the Service Brake section to inspect the brake shoes.

ADJUST THE SERVICE BRAKES

The brake system is automatically adjusted. A low brake pedal or lack of braking power could be caused by:

• Brake fluid level low in the master cylinder. See

Check the Master Cylinder Fluid section.

• Air in the brake lines. See Bleed the Brakes

section.

• Worn brake pads or shoes. See Inspect the

Service Brake section.

Worn brake rotors or drums. See Inspect the

Service Brake section.

• Mechanical defect in the rear brake auto adjust

mechanism.

• Binding brake pedal linkage.

If you are experiencing a low brake pedal or lack of braking power, the entire brake system should be inspected.

8. Inspect all brake cables and linkages for any signs of damage or missing cotter pins.

9. Inspect the park brake handle locking mechanism for any signs of damage or wear.

10.Set the park brake.

11. Reconnect the main positive and negative cables at the batteries.

12.Remove the blocks from the wheels

Brakes Page 4

Page 65

Maintenance, Service, and Repair

ADJUST THE PARKING BRAKE

There are two adjustments for the park brake system:

1. Primary.

2. Secondary. This adjustment should only be performed when the primary adjustment is beyond its limits or any rear brake components have been replaced.

Primary Adjustment

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and negative

cables at the batteries.

6. Release the park brake

7. Rotate the knob on the end of the park brake handle until the parking brake holds firm when applied.

8. Set the park brake.

9. Reconnect the main positive and negative cables at the batteries.

10. Remove the blocks from the wheels.

11. Release the park brake and test drive the vehicle.

Secondary Adjustment

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Release the park brake.

7. Turn the primary adjustment until the park brake

is as loose as possible.

8. Adjust the clevis on the park brake cable equalizer

until all slack in the brake cables have been taken up but the brake is not actuated.

NOTE: The equalizer is located under the frame just

in front of the front battery compartment.

9. Perform primary adjustment procedure.

10. Set the park brake.

11. Reconnect the main positive and negative cables

at the batteries.

12. Remove the blocks from the wheels.

13. Release the park brake and test drive the vehicle.

Brakes

Page 5

Page 66

Maintenance, Service, and Repair

CHECK MASTER CYLINDER FLUID

Do not ingest brake fluid or allow contact with skin or eyes. Always wear protective clothing and a face shield when working with or around brake fluid.

SKIN CONTACT

Flush area immediately with water for several minutes. If a rash or skin irritation develops, get medical attention immediately.

EYE CONTACT

Immediately flush the eye with water for 15 minutes and call physician.

INGESTION

Get medical attention immediately.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Thoroughly clean the area around the master cylinder cap.

7. Remove the master cylinder cap.

8. If the fluid in the master cylinder is contaminated then the entire brake system must be flushed. Refer to Bleed the Brakes for information regarding flushing the brake system.

9. Fill with brake fluid from a new sealed container to within 1/4-inch of the top of the master cylinder chamber and reinstall the cap.

10.Reconnect the main positive and negative cables at the batteries.

11. Remove blocks from behind the wheels.

12.Release the parking brake and test drive the vehicle.

• Only use DOT 3 brake fluid from a new sealed container.

• DOT 3 brake fluid is corrosive and will damage paint finishes.

• Dispose of brake fluid in accordance with local state and federal

regulations.

• Read and follow all warnings on the brake fluid container.

Brakes Page 6

Page 67

Maintenance, Service, and Repair

BLEED THE BRAKE SYSTEM

Do not ingest brake fluid or allow contact with skin or eyes. Always wear protective clothing and a face shield when working with or around brake fluid.

SKIN CONTACT

Flush area immediately with water for several minutes. If a rash or skin irritation develops, get medical attention immediately.

EYE CONTACT

Immediately flush the eye with water for 15 minutes and call physician.

INGESTION

Get medical attention immediately.

NOTE: Start this procedure at the wheel furthest from the master cylinder, then work toward the wheel

closest to the master cylinder.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Thoroughly clean the area around the master cylinder cap and remove the cap.

7. Add brake fluid from a new sealed container to the master cylinder. Fill to 1/4” from the top of the master cylinder chamber.

8. The master cylinder fluid level will drop as the brakes are bled. Periodically check and fill the master cylinder during this procedure. Do not allow the fluid level in the master cylinder to drop too low as this will allow air into the brake lines.

9. Attach a clear hose to the bleeder valve on the brake cylinder that is to be bled. Route the hose into a clear container for waste brake fluid.

10. Pump the brake pedal a few times and then press and hold light pressure to the brake pedal.

11. Open the bleeder valve on the brake cylinder.

12. Depress the foot pedal to the floor and then close the bleeder valve. Do not release pressure on the brake pedal until the bleeder valve is closed.

• Only use DOT 3 brake fluid from a new sealed container.

• DOT 3 brake fluid is corrosive and will damage paint finishes.

• Dispose of brake fluid in accordance with local state and federal

• Read and follow all warnings on the brake fluid container.

regulations.

Brakes

Page 7

Page 68

Maintenance, Service, and Repair

13.Slowly release the foot pedal, allowing it to return to its released position.

NOTE: Check and fill the master cylinder frequently during the bleeding process. Do not allow the fluid

level in the master cylinder to drop low enough to allow air to enter the brake lines. If air enters the brake lines during the bleeding process, then you will have to start again from the beginning.

14.Repeat the above steps until you are sure that all of the air is expelled from the brake line. Any air bubbles that can be seen in the clear hose attached to the bleeder is an indication that there is still air in the brake lines.

15.Repeat this process with each of the other wheels.

NOTE: When finished, top off the master cylinder with fluid. See Check Master Cylinder Fluid for

information on filling the master cylinder.

16.Reconnect the main positive and negative cables at the batteries.

17.Remove the blocks from behind the wheels.

18.Release the park brake and test drive the vehicle.

Always use brake fluid from a new sealed container. Never reuse any brake fluid that has been removed from the brake system. Use of contaminated brake fluid will degrade the braking performance and may cause property damage or severe bodily injury.

• Only use DOT 3 brake fluid from a new sealed container.

• DOT 3 brake fluid is corrosive and will damage paint finishes.

• Dispose of brake fluid in accordance with local state and federal

regulations.

• Read and follow all warnings on the brake fluid container.

Brakes Page 8

Page 69

Maintenance, Service, and Repair

FLUSH THE BRAKE SYSTEM

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the front and rear wheels off of the ground and support with jack stands.

7. Release the park brake.

8. Remove the front and rear wheels. Refer to Tires and Wheels section for information regarding

removing the wheels.

9. Remove the wheel cylinders from each axle. Refer to Replace the Wheel Cylinder section for

information regarding removing the wheel cylinder.

10. Attach a clear hose to the bleeder valve on each of the wheel cylinders and route the hoses into a container for waste brake fluid.

11. Position the wheel cylinders so that the bleeder screw is pointing to the ground and open all bleeder screws.

12. Pump the master cylinder until all fluid has been pumped from the brake lines and all wheel cylinders.

13. Close all bleeder screws.

14. Fill the master cylinder with fluid.

15. Open one of the bleeder screws and pump the master cylinder until all fluid has been pumped from the master cylinder and close the bleeder screw.

16. Repeat the above two steps for each wheel cylinder.

17. Reinstall the wheel cylinders and bleed the brakes. Refer to Bleed the Brakes for information regarding bleeding the brakes.

18. Set the park brake.

19. Install the wheels and lower the vehicle to the ground.

20. Reconnect the main positive and negative cables at the batteries.

21. Release the park brake and test drive the vehicle.

Brakes

Page 9

Page 70

Maintenance, Service, and Repair

REPLACE REAR BRAKE SHOES

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Confirm the electric park brake is set.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

When replacing brake components, it is recommended to replace both left and right side at the same time.

6. Raise the rear of the vehicle and support with jack stands.

7. Remove the rear wheel and brake drum.

8. Remove Springs (1, 6, 12).

9. Remove park brake cable (10), cam (9) and guide (15).

10.Remove brake shoe hold down cups, springs and pins (4).

11. Remove the brake shoes (5), adjustor (7, 8), and park brake link and spring (2, 3).

12.Pry the horseshoe clip (13) and remove the park brake arm (11). Discard the horseshoe clip.

DO NOT reuse the horseshoe clip. The clip is damaged when it is removed and may fail if it is reinstalled. This will result in failure of the brake system.

13. Reassemble the brake in reverse order.

• Use a new horseshoe clip (13)

• Thoroughly clean the adjusting nut (8) threads and

apply a light film of high temperature grease to the threads.

• Before installing the brake drum, depress the brake

pedal and check to be sure that the auto adjust mechanism is functioning properly.

14. Repeat procedure for other side of vehicle.

Preliminary brake adjustment:

With the brake drum and wheel installed, remove the plug from the adjuster access hole.

While rotating the wheel, using brake spoons, rotate the star wheel (8) until the brake is locked and the wheel cannot be turned by hand.

Loosen the star wheel (8) just enough so that the wheel rotates with no brake drag.

Repeat for other side of vehicle. Test drive the vehicle.

Brakes Page 10

Page 71

Maintenance, Service, and Repair

Rear Brake (left side shown)

Brakes

Page 11

Page 72

TAYLOR -DUNN

Page 73

TABLE OF CONTENTS

Inspecting the Motor Brushes ............2

Motor Inspection................................2

Motor Removal and Installation .........4

Replacing the Brushes.......................5

Replacing the Bearings .....................6

Repairing the Commutator ................6

Service Limits ...................................7

Typical Exploded Motor

Motor Service

Page 74

Motor Service

INSPECTING THE MOTOR BRUSHES

Typical motor with cooling fan indicated by

the arrow

NOTE: There are four brushes in the motor. The

brushes will not wear at the same rate. It is recommended that all four brushes are inspected at the same time.

NOTE: In some vehicle configurations it may not be

possible to inspect all four brushes while the motor is in the vehicle. Refer to

Transmission Service section for

information on removing the motor.

MOTOR INSPECTION

Disassembly

1. Remove the motor from the vehicle. See the

2. Remove the housing screws from the rear and/or

Typical brush and brush holder

Transmission section for information on

removing the motor.

front of the motor.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Look through the brush cover and compare the top of the brush to the top of the brush holder. If it is even with or below the top of the brush holder then the brushes should be removed and measured. Refer to Replacing the Brushes section for information regarding removing the motor brushes.

7. If any one brush is less than or equal to the service limit specified in Service Limits, then all four brushes should be replaced.

8. Reconnect the main positive and negative cables at the batteries.

3. Remove the armature retaining screws from the rear housing (if equipped).

4. If this is an enclosed motor, remove the front housing end.

5. Pull the armature out of the front end of the motor housing.

6. Remove the nuts off of all of the terminals in the rear motor housing.

7. Remove the rear motor housing being careful not to damage the field coil wires.

9. Remove the blocks from behind the wheels, release the park brake and test drive.

Motor

Page 75

Motor Service

Inspection

1. Measure the length of each motor brush.

• If any one brush is less than or equal to the

service limit specified in section Service

Limits, then all four brushes should be

replaced. Refer to Replacing the Brushes section for information regarding replacing the motor brushes.

2. Measure the diameter of the commutator.

• If the commutator is less than the minimum

diameter specified in section Service Limits, then the motor must be replaced.

3. Measure the commutator undercut depth in 5places around the commutator.

• If any one of the measurements is less than the

minimum undercut depth specified in Service

Limits above, then the commutator must be

undercut. Refer to Repair Commutator section for information regarding undercutting the commutator.

Undercut

Incorrect

Hacksaw blade

Correct

Insulation

Armature

Min. OD

5. Inspect the commutator for burn marks.

• Burn marks and/or raised commutator segments 90 or 180 degrees apart is evidence of a shorted armature. A tool called a growler is required to reliably test for a shorted armature.

Typical burn mark on a shorted armature

6. Inspect the commutator for raised segments. Raised segments could be a result of a stalled motor or shorted armature. A tool called a growler is required to reliably test for a shorted armature.

• If the armature is not shorted then the raised

segments can be removed by machining the commutator. Do not machine the commutator past the minimum diameter specified in

Service Limits section. Refer to Repair Commutator section for information regarding

machining the commutator.

7. Visually inspect the armature windings for burnt insulation. Burnt insulation is a direct result of motor overheating and could lead to a shorted armature.

• If the insulation is cracked or burnt, then it is

recommend that the armature or motor be replaced.

NOTE: If the armature has been burnt then there is a

good possibility that the field windings may also be burnt. Symptoms indicating a shorted field include high motor current, lack of power and possibly excessive speed.

8. Using a growler, test the armature for shorts.

• If the armature is shorted, then we recommend

that the armature or motor be replaced.

Commutator

4. Inspect the commutator for grooves.

• If the commutator is groved then it must be machined on a lathe. Do not machine the commutator past the minimum diameter specified in Service Limits section. Refer to

Repair Commutator section for information

regarding machining the commutator.

9. Using the continuity function of digital multi meter, check the continuity around the entire commutator by placing one test lead against one of the commutator segments and the other test lead against all of the other segments one at a time. There should be continuity around the entire commutator. If any segment indicates an open circuit, then the motor must be replaced.

Motor

Page 76

Motor Service

10.Using the continuity function of digital multi meter, check the continuity from any one of the commutator segments and the armature frame. If it is not an open circuit, then the armature is shorted and the motor must be replaced.

11. Rotate the motor bearing(s) by hand.

• The bearing should not ‘freewheel’ but should

come to a smooth stop when rapidly spun by hand. If the bearing freewheels, then grease is no longer present in the bearing and it must be replaced. Refer to Replacing the Bearings section for information regarding replacing the armature bearings.

• Feel for any roughness when the bearing is

rotated. If any roughness or grinding is noticed then the bearing must be replaced. Refer to

Replacing the Bearings section for

information regarding replacing the armature bearings.

Assembly

MOTOR REMOVAL AND INSTALLATION

See the Transmission section for information on removing or installing the motor.

NOTE: If this is an enclosed motor on a vehicle with

a Power Traction primary reduction, then it is recommended to replace the armature shaft seal any time the motor is disassembled.

1. Push the motor brushes just far enough out of the brush holder so that the brush springs hold them in place away from the commutator. See the illustration to the right.

2. Install the rear motor housing to the stator housing.

3. Lightly grease the outside diameter of the armature bearings.

4. Insert the armature through the stator housing and seat the bearing into the rear housing.

5. If equipped with armature retaining screws, install and tighten them at this time.

6. If this is an enclosed motor, lightly grease the armature shaft seal and install the front motor housing.

NOTE: If the vehicle is equipped with a belt type

primary reduction then the spring on the motor seal should be removed. Failure to remove the spring may result in a high pitched squeal from the seal.

7. Push the motor brushes into the brush holder until the brush spring snaps into place. Be certain that the spring does not rest up against the brush wire. See the illustrations below.

Motor

Page 77

Motor Service

Brush Spring Orientation

REPLACING THE BRUSHES

NOTE: It is recommended that all four brushes be replaced as a set. NOTE: Motors without removable brush covers must be disassembled

to replace the brushes. Refer to Motor Inspection- Disassembly section for information on taking the motor apart.

NOTE: Some motors are equipped with brush pairs. These motors

must be disassembled to replace the brushes. Refer to Motor

Inspection-Disassembly section for information on taking

the motor apart. Refer to the Motor Parts List for your vehicles brush configuration.

NOTE: Some motors have brush leads that are routed through or

behind the brush holder assembly. In this case, the brush holder assembly must be removed to replace the brushes.

NOTE: The motor must be removed from the vehicle for this procedure.

Refer to Transmission Service section for information on removing the motor.

1. Remove the brush covers.

2. Loosen the brush wire retaining screw and remove the brush from the brush holder. Be careful with the brush spring and do not let it slip off of the spring mount. If the spring comes off, then the motor must be disassembled. Refer to Motor Inspection-

Disassembly section for information on taking the motor apart.

3. Install the new brushes in reverse order.

4. Be certain that the brush springs do not rest up against the brush wires. Refer to illustrations in Motor Inspection-Assembly for proper brush spring position.

Motor

Page 78

Motor Service

Page 6

REPLACING THE BEARINGS

1. The motor must be removed from the vehicle for this procedure. Refer to Transmission Service section for information on removing the motor.

2. Remove the armature. Refer to Motor Inspection- Disassembly section for information on taking the motor apart.

3. Press the armature bearing(s) off of the armature shaft.

Do not press against the outer race of the bearing. Pressing against the outer race will damage the bearing and may result in premature failure of the bearing. See the illustration below

6. Measure the commutator undercut depth in 5places around the commutator. If any one of the measurements is less than the minimum undercut depth specified in Service Limits, then the commutator must be undercut.

Example of freshly cut commutator

7. While still in the lathe, smooth the commutator with fine emery cloth.

4. Press new bearing(s) onto the shaft.

5. Reassemble the motor.

REPAIRING THE COMMUTATOR

1. The motor must be removed from the vehicle for

this procedure. Refer to Transmission Service section for information on removing the motor.

2. The armature must be removed from the motor

for this procedure. Refer to Motor Inspection-

Disassembly section for information on taking

the motor apart.

3. Using a lathe, cut the armature just enough to remove all grooves, depressions or ridges.

Undercutting the commutator

1. Using a small straight cut saw blade, cut the commutator insulation to the proper depth. Refer to undercut depth in Service Limits.

2. Once all segments have been properly undercut, mount the armature in a lathe and smooth the commutator with fine emery cloth.

3. Inspect the armature for shorts. Refer to Motor Inspection section for information on testing the armature.

NOTE: Copper debris in the undercut area can give

a reading of a shorted armature.

Properly undercut and cleaned

commutator segments

4. Measure the diameter of the commutator. If the commutator is less than the minimum diameter specified in Service Limits, then the motor must be replaced.

5. Thoroughly clean all copper debris from between the commutator segments.

Motor

Page 79

SERVICE LIMITS

Motor Service

Motor Specification

Undercut Depth

Commutator Diameter

(min)

Brush Length

(min)

Wire Depth

(max)

Number

mm inches mm inches mm inches mm inches 5BC58JBS6129A 0.635 0.025 66.75 2.625 19.05 0.75 38.1 1.5 5BC58JBS6129B 0.635 0.025 66.75 2.625 19.05 0.75 38.1 1.5 5BC58JBS6129C 0.635 0.025 66.75 2.625 19.05 0.75 38.1 1.5 5BC49JB399C 0.635 0.025 78.97 3.109 19.05 0.75 - 5BC58JBS6110C 0.635 0.025 78.97 3.109 19.05 0.75 38.1 1.5 5BT1326B262A 0.635 0.025 78.97 3.109 19.05 0.75 - 5BT1326B96 0.635 0.025 96.8 3.810 19.05 0.75 - 5BT1344B185 0.635 0.025 104.8 4.125 20.3 0.80 - -

L94-4006 0.635 0.025 96.8 3.810 19.05 0.75 - A02-4011 1.0 .04 69.9 2.75 16 0.62 - ER5-4001

XP-2023

1.0 .04 69.9 2.75 16 0.62 - -

ER5-4002 1.0 .04 69.9 2.75 16 0.62 - BP5-4002 1.0 .04 69.9 2.75 16 0.62 - -

Motor

Page 80

TAYLOR -DUNN

Page 81

TABLE OF CONTENTS

Cleaning............................................2

Testing ..............................................3

Charging ...........................................4

Watering ...........................................5

Single Point Battery Watering System ................. 5

Replacing (6-volt batteries only) ........6

Moist Charge Batteries ......................................... 7

Storage and Returning to Service ......8

Storage .................................................................. 8

Returning to Service ............................................. 9

Battery Service

Page 82

Maintenance, Service, and Repair

CLEANING

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Dry dirt can be readily blown off with low-pressure air or brushed off.

7. Wetness or wet dirt on the batteries indicates battery acid. Using a nonmetallic brush with flexible bristles, wash the batteries off with a strong solution of baking soda and hot water (1 lb. of soda to a gallon of water). Continue until all fizzing stops, which indicates that the acid has been neutralized. Then rinse thoroughly with clear water. DO NOT get any of the solution into the battery cells.

8. Reconnect the batteries, remove the blocks from the wheels and test drive.

A battery is a live electrical source. It cannot be disconnected or neutralized. Do not drop any tool or conductive object onto the battery. A conductive object that comes in contact with the battery terminals will initiate a short circuit of the battery. This could cause the battery to explode resulting in severe bodily injury and/or property damage.

Battery electrolyte will stain and corrode most surfaces. Immediately and thoroughly clean any surface outside of the battery that the battery electrolyte comes in contact with. Failure to clean may result in property damage.

Batteries Page 2

Page 83

TESTING

Maintenance, Service, and Repair

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

NOTE: A combination of the Load Test and Specific

Gravity Test should be used to accurately determine the condition of the batteries.

Load Test (6-volt batteries only)

NOTE: The batteries must be fully charged before

performing this test.

1. Clean the batteries. Refer to Cleaning the

Batteries section for information on cleaning the

batteries.

2. Load test each battery using a battery load test meter (available at most auto parts distributors). Follow the instructions provided with the test meter.

• If any battery fails the load test, then it should be replaced.

NOTE: If the batteries are over one year old, it is

recommended to replace them as a set.

• If all batteries fail the test you should check the charging system before replacing the batteries. Refer to Charger Troubleshooting section for information on checking the charging system.

Specific Gravity Test

NOTE: The batteries must be fully charged before

performing this test.

The specific gravity of a cell is an indication of the actual state of charge of the cell. A fully charged cell should have a reading of 1275 to 1300 (see the illustration to the right). A discharged battery will read 1100. Ideally, all cells in a battery pack will have the same reading. Any cells in a battery pack that vary by more than 30points may be an indication of a bad cell.

Batteries

Page 3

Page 84

Maintenance, Service, and Repair

Clean the batteries. Refer to Cleaning the Batteries section for information on cleaning the batteries.

Using part number 77-200-00 hydrometer, check and record the specific gravity of each cell in the battery pack.

If, after charging, none of the cells exceed a hydrometer reading of 1250 then there may be a fault in the charging system. If the charging system checks OK then the batteries are no longer accepting a charge and should be replaced.

NOTE: Refer to Charger Troubleshooting for

information on checking the charging system.

The highest reading will be the cell that is accepting the most charge. This reading will be used to gauge all other cells.

Compare the specific gravity readings to the highest reading, if the difference between any of the cells is more than 30-points, then that battery should be replaced.

NOTE: If the batteries are over one year old, it is

recommended to replace them as a set.

Reconnect the batteries, remove the blocks from the wheels and test drive.

Typical Hydrometer Float

CHARGING

Refer to Charging Your Vehicle in section Safety

Rules and Operating Instructions.

Batteries Page 4

Page 85

WATERING

Maintenance, Service, and Repair

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

NOTE: The electrolyte level in a battery rises while

charging and will be close to its highest level after the end of a charging cycle. It is recommended to fill the batteries at the end of a charging cycle. If the electrolyte is below the top of the battery plates then fill just enough to cover the plates and then top off when the charging cycle is complete.

6. Clean the batteries. Refer to Cleaning the Batteries section for information on cleaning the

batteries.

7. Check the electrolyte level in all battery cells. If low, fill to the correct level with distilled water using part number 77-201-00 battery filler, never add additional battery electrolyte to the batteries.

8. Reconnect the batteries, remove the blocks from the wheels and test drive.

Do not overfill the batteries. Over filling the batteries may cause the battery electrolyte to boil out of the battery and result in severe bodily injury or property damage.

Single Point Battery Watering System

This system enables you to water all of the batteries at the same time from a single point. This system also automatically shuts off water to each cell when the cell is at the proper level.

Refer to www.batteryfillingsystems.com for more detailed information.

Batteries

Page 5

Page 86

Maintenance, Service, and Repair

REPLACING (6-VOLT BATTERIES ONLY)

NOTE: If the batteries are over one year old, it is

recommended to replace them as a set.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Thoroughly clean the batteries and battery

compartment. Refer to Cleaning in this section for information regarding cleaning the batteries.

7. Remove the battery hold downs.

8. Inspect the battery hold downs for corrosion. If any signs of corrosion are seen then the battery hold downs should be replaced.

Do not leave cables on batteries that have been removed from the vehicle. Cables left on batteries could cause a short circuit resulting in battery explosion, severe bodily injury and/or property damage.

9. Remove all battery jumpers from both posts of the battery or batteries being replaced.

NOTE: It is recommended to replace the battery

jumpers when replacing the batteries.

10. Remove the batteries from the vehicle.

11. Inspect the battery compartment for signs of corrosion.

12. If minimal signs of corrosion are seen, then the damaged paint should be stripped off and the entire battery compartment prepped and repainted.

13. If there are excessive signs of corrosion, then it may be necessary to replace some of the frame members or completely rebuild the battery compartment.

Batteries Page 6

14. Inspect the main positive and negative cables and terminals, charger cables and terminals and 12volt tap wiring. If any of the terminals or wires show signs of corrosion, then they must be repaired or replaced.

Page 87

Maintenance, Service, and Repair

15. Install the batteries in reverse order. Refer to the Illustrated Parts List for battery cable routing.

16. It is recommended to replace the battery terminal hardware when replacing the batteries.

When torquing battery hardware, use a backup wrench on the battery bolt and tighten the nut. Failure to use a backup wrench may damage the battery post.

17. Torque the terminal hardware to 7-8 ft.-lbs.

18. Tighten the hold downs so that the batteries are secure but not so tight as to deform the batteries.

19. Remove the blocks from the wheels and test drive.

Moist Charge Batteries

Moist charged batteries are shipped without battery electrolyte. This allows for a much greater shelf life of the battery. Moist charged batteries must be filled with electrolyte and charged before putting into service. Battery electrolyte is a solution of acid and water that is formulated to be used in wet lead acid batteries and is available at most automotive parts distributors that carry batteries.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

Do not operate or charge a vehicle equipped with moist charged batteries until the batteries have been filled with electrolyte and charged. Operating or charging moist charged batteries before filling and charging will damage the batteries resulting in premature failure of the batteries.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Fill all battery cells with electrolyte to the proper level.

7. Thoroughly clean any spilled electrolyte from the batteries or the ground. Refer to Cleaning the

Batteries for information on cleaning the

batteries.

8. Reconnect the battery cables, connect the batteries to the charger and allow the charger to complete one charging cycle.

9. Remove the blocks from the wheels and test drive. The batteries are now ready to be put into service.

Batteries

Page 7

Page 88

Maintenance, Service, and Repair

STORAGE AND RETURNING TO SERVICE

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

If the batteries are removed from the vehicle, do not place them directly on the ground, concrete or solid metal surface. It is recommended to store them on a wooden pallet or equivalent. Storing on the ground, concrete or solid metal surface will cause the batteries to discharge and may result in premature failure of the batteries.

Storage

Thoroughly clean the batteries and battery compartment. Refer to Cleaning in this section for information regarding cleaning the batteries.

Check the electrolyte level and charge the batteries. Refer to Watering in this section for information regarding checking the electrolyte level.

Store the vehicle or batteries in a cool, dry, well ventilated area.

If storing for more than one month, the batteries should be charged as follows:

Storage

Temperature

(F)

Over 60 1

Between 40 and 60 2

Below 40 6

Charging Interval

(months)

Batteries Page 8

Page 89

Returning to Service

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Thoroughly clean the batteries and battery compartment. Refer to Cleaning in this section for information regarding cleaning the batteries.

7. Check the electrolyte level and charge the batteries. Refer to Watering in this section for information regarding checking the electrolyte level.

Maintenance, Service, and Repair

8. Test the batteries. Refer to Testing section for information on testing the batteries.

9. The batteries are now ready to be put back into service.

Batteries

Page 9

Page 90

TAYLOR -DUNN

Page 91

TABLE OF CONTENTS

Throttle Linkage Adjustments ............2

Magnetic Module.................................................. 2

Pot Box module .................................................... 3

Throttle Linkage

Page 92

Maintenance, Service, and Repair

Page 2

THROTTLE LINKAGE ADJUSTMENTS

Magnetic Module

The standard magnitic throttle module should not be used in areas that contain large magnetic fields. Large magnitic fields may effect the operation of the module resulting in unexpected movement of the vehicle.

The throttle pedal is attached directly to the throttle module. There are no adjustments to the throttle linkage. There are no serviceable components in the throttle module.

The standard throttle position sensor consists of two micro switches and a magnetic sensor that detects the position of the throttle pedal.

Switch FS-3 is a normally open switch that is held closed by the throttle pedal return spring. The vehicle will be disabled if the throttle return spring breaks.

Switch FS-1 closes just as the throttle pedal is depressed. Depending on the control system in the vehicle, the throttle

position output is obtained from pin #1 (0-5v) or pin #2 (611v).

The start signal output is either a positive or a negative signal from pin #5. The polarity of the signal depends on the type of control system in the vehicle and will be the same as the voltage into pin #4.

6-11 Volt output

36v+ Input

B- Input

FS-1

FS-3

2 7

9 4

Front Axle

Throttle Module Internal Wiring

Throttle Module

Page 93

Maintenance, Service, and Repair

Page 3

Pot Box module

The pot box module is used on vehicles that are to be operated in areas with large magnetic fields.

The linkage to the pot box should be adjusted so that the FS-1 switch closes just as the pedal is depressed and the output is at 5K with the pedal fully depressed.

1 2

8 9

FS-1

Pot Box Module

Front Axle

Page 94

TAYLOR -DUNN

Page 95

TABLE OF CONTENTS

Tire Inflation ......................................2

Tire Inspection...................................2

Replace the Tire/Wheel .....................3

Replace the Tire (pneumatic) ...........3

Repair the Tire (pneumatic) ..............4

Replace the Tire (pneumatic) ...........5

Tires and Wheels

Page 96

Maintenance, Service, and Repair

TIRE INFLATION

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

There are many tire options available with varying tire pressures. Refer to the side wall of your tire for information regarding the tire pressure for your tires.

The illustration to the right is an example of the side wall information on a tire.

Tire pressures must be checked when the tire is cold.

TIRE INSPECTION

6. Check the tire pressure. Refer to Tire Inflation section for information on checking the tire pressure.

7. Inspect the tire tread depth. Minimum recommended tread depth is 1/16-inch. There are a series of tread depth wear indicators around the circumference of the tire. They will appear as 1/2-inch bands across the tread as the tire approaches its wear limit (see illustration below). Replace the tire if any tread depth indicator can be seen or any part of the tread depth is 1/16inch or less. Refer to Replace the Tire section for information regarding replacing the tire.

8. Inspect for uneven tire wear on the front tires. Uneven tire wear could be a result of an improperly inflated tire or a misaligned or damaged front end.

NOTE: Refer to Tire Inflation section or Steering

Component Service section for information

on proper tire inflation or front end wheel alignment.

9. Inspect the inner and outer side walls for cracks. If any cracks are seen, then the tire should be replaced. Refer to Replace the Tire section for information regarding replacing the tire.

10. Inspect the valve stem for cracks. If any cracks are seen, then the valve stem should be replaced. It is also recommended that the valve stem be replaced whenever the tire is replaced.

NOTE: Refer to Replace the Tire section for

information regarding replacing the valve stem.

11. Inspect the tread and side walls for debris in the rubber that could lead to a puncture. If any debris is found it should be removed and the tire inspected for a leak.

Tires and Wheels Page 2

Page 97

Maintenance, Service, and Repair

Page 3

REPLACE THE TIRE/WHEEL

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

5. Disconnect the main positive and negative cables at the batteries.

6. Raise the wheel to be replaced off of the ground and support with jack stands.

7. Remove the 4 or 5 wheel nuts and remove the wheel.

8. Install in reverse order.

9. Following the pattern shown on the following page, cross tighten the wheel nuts in two stages as follows:

REPLACE THE TIRE (PNEUMATIC)

NOTE; To replace the tire, the tire/wheel assembly

must be removed from the vehicle. Refer to

Replace the Tire/Wheel section for

information on removing the tire/wheel assembly.

Tire replacement should only be performed by personnel trained in tire replacement.

The tire replacement procedure will be unique to the type of replacement equipment being used. Refer to the instructions provided with your equipment.

Always use a new valve stem when replacing a tire.

Explosion Hazard. Fully deflate the tire before attempting to remove the tire from the wheel. Do not over inflate the tire when seating the bead. Failure to deflate the tire or over inflating the tire to seat the bead may cause explosive failure of the tire resulting in severe bodily injury or death.

1st stage to approximately 20 ft-lbs. 2nd stage to 80-90 ft-lbs.

10. Reconnect the main positive and negative cables at the batteries.

11. Lower the wheel to the ground.

12. Remove the blocks from behind the wheels.

13. Release the parking brake and test drive the vehicle.

1. Remove the tire from the wheel.

2. Cut the old valve stem off of the wheel.

3. Remove the valve stem cap from the new valve stem.

4. Lubricate the valve stem with liquid soap.

5. Install a new valve stem using a valve stem tool.

NOTE: The valve stem tool is available at most auto

repair shops.

6. Install the tire onto the wheel following the instructions provided with your tire replacement equipment.

7. Inflate the tire to the proper pressure and check for leaks.

8. Install the valve stem cap.

Tires and Wheels

Page 98

Maintenance, Service, and Repair

4 1

4-Bolt Pattern

5-Bolt Pattern

Pattern for tightening the wheel nuts

Re-torque all wheel nuts to their final value after 1-week (20-hours) of operation. Failure to re-torque the wheel nuts may result in the wheel coming off of the vehicle causing severe bodily injury and/or property damage.

REPAIR THE TIRE (PNEUMATIC)

8-Bolt Pattern

Do not attempt to repair a tire with a damaged side wall or a slice in the tread. This type of repair could fail prematurely resulting in severe bodily injury and/or property damage.

NOTE: To properly repair a puncture, the tire must be removed from the wheel. Refer to Replace the

Tire section for information on removing the tire from the wheel.

It is recommended to repair a tire with a combination vulcanized plug and internal patch. Tire repairs should only be performed by personnel trained in tire repair. The tire repair procedure will be unique to the type of repair equipment or repair components used. Refer to

the instructions provided with your equipment or repair components.

Tires and Wheels Page 4

Page 99

Maintenance, Service, and Repair

Page 5

REPLACE THE TIRE (PNEUMATIC)

NOTE; To replace the tire, the tire/wheel assembly must be removed from the vehicle. Refer to Replace

the Tire/Wheel section for information on removing the tire/wheel assembly.

Tire replacement should only be performed by personnel trained in tire replacement. The tire replacement procedure will be unique to the type of replacement equipment being used. Refer to

the instructions provided with your equipment. Always use a new valve stem when replacing a tire.

1. Remove the tire from the wheel.

2. Cut the old valve stem off of the wheel.

3. Remove the valve stem cap from the new valve stem.

4. Lubricate the valve stem with liquid soap.

5. Install a new valve stem using a valve stem tool.

NOTE: The valve stem tool is available at most auto repair shops.

6. Install the tire onto the wheel following the instructions provided with your tire replacement equipment.

7. Inflate the tire to the proper pressure and check for leaks.

8. Install the valve stem cap.

Tires and Wheels

Page 100

TAYLOR -DUNN