Taurus TT-CW 18 Li Instruction Manual

LI-ION 18V

Cordless Impact Driver

N26704

INSTRUCTION MANUAL

AFTER SALES SUPPORT

TEL: [phone]

EMAIL: [e-mail]

Cordless Impact Driver

TT-CW 18 Li

2

After Sales Support EMAIL: [e-mail]: [phone]

CORDLESS IMPACT DRIVER

What your 3 year warranty means

Great care has gone into the manufacture of these products and they should therefore provide you with years
of good service when used properly. In the event of product failure within its intended use over the course
of the rst 3 year after the date of purchase, we will remedy the problem as quickly as possible once it has been
brought to our attention. In the unlikely event of such an occurrence, or if you require any information about
the product, please contact us via our after sales support services, details of which can be found in this manual
and on the product itself.

Welcome Section

Congratulations on choosing to buy a TAURUS TITANIUM® product.

All products brought to you by TAURUS TITANIUM® are manufactured to the highest standards of performance
and safety, and, as part of our philosophy of customer service and satisfaction, are backed by our
comprehensive 3 Year Warranty.

We hope you will enjoy using your purchase for many years to come.

Table of Contents

1. General Safety Rules

2. Battery Safety Rules

3. Charger Operating Instruction

3.1. Charger Safety Rules

3.2. Layout

3.3. Technical data

3.4. Operation

3.5. Cleaning and maintenance

3.6. Disposal and recycling

4. Cordless Impact Driver Operating Instructions

4.1 Cordless Impact driver saftey rules

4.2. Layout

4.3. Items Supplied

4.4. Proper Use

4.5. Technical data

4.6. Before starting the equipment

4.7. Operation

4.8. Cleaning, maintenance and ordering of spare parts

4.9. Disposal and recycling

4.10 Storage

Pg. 3

Pg. 4

Pg. 6

Pg 7

Pg. 7

Pg. 7

Pg. 7

Pg. 8

Pg. 8

Pg. 9

Pg. 11

Pg. 11

Pg. 11

Pg. 11

Pg. 11

Pg. 12

Pg. 12

Pg. 13

Pg. 13

Pg. 13

3

After Sales Support EMAIL: [e-mail]: [phone]

plugging in power tools that have the switch
on invites accidents.

d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to rotating part of the power tool may
result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.
g. If devices are provided for the connection of

dust extraction and collection facilities, ensure
these are connected and properly used. Use of

these devices can reduce dust-related hazards.

4. Power tool use and care
a. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

b. Do not use the power tool if the switch does not
turn it on and o. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source

and/ or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk
of starting the power tool accidentally.
d. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may aect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool bits

etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use

of the power tool for operations dierent from
those intended could result in a hazardous
situation.

5. Service
a. Have your power tool serviced by a qualied

repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

6. Recommendation

We recommend that the tool always be supplied
via a residual current device with a rated residual
current of 30mA or less.

1. GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to

follow all instructions listed below may result
in electric shock, re and/or serious injury. The
term ’’power tool’’ in all of the warnings listed
below refers to your mains-operated (corded)
power tool or battery-operated (cordless) power
tool.

SAVE THESE INSTRUCTIONS

1. Work area

a. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b. Do not operate power tools in explosive

atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

2. Electrical safety
a. Power tools plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)
power tool. Unmodied plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords

increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk
of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety
a. Stay alert, watch what you are doing and use

common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.
b. Use safety equipment. Always wear eye
protection. Safety equipment such as a dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the o-position before plugging in. Carrying
power tools with your nger on the switch or

4

After Sales Support EMAIL: [e-mail]: [phone]

2. BATTERY SAFETY RULES

Battery tool use and care

a) Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with another
battery pack.

b) Use power tools only with specically designated battery
packs. Use of any other battery packs may create a risk of

injury and re.

c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals

together may cause burns or a re.

d) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.

Additional safety instructions

We pay a great deal of attention to the design of every
battery pack to ensure that we supply you with batteries
which feature maximum power density, durability and
safety. The battery cells have a wide range of safety devices.
Each individual cell is initially formatted and its electrical
characteristic curves are recorded. This data is then used
exclusively to be able to assemble the best possible battery
packs. Despite all the safety precautions, caution must

always be exercised when handling batteries. The following
points must be obeyed at all times to ensure safe use.

Safe use can only be guaranteed if undamaged cells are
used. Incorrect handling can cause cell damage.

Important: Analyses conrm that incorrect use and poor

care are the main causes of the damage caused by high
performance batteries.

Information about the battery

1. The battery pack supplied with your cordless tool is not
charged. The battery pack has to be charged before you
use the tool for the rst time.

2. For optimum battery performance avoid low discharge
cycles. Charge the battery pack frequently.

3. Store the battery pack in a cool place, ideally at 15°C and
charged to at least 40%.

4. Lithium-ion batteries are subject to a natural ageing
process. The battery pack must be replaced at the latest
when its capacity falls to just 80% of its capacity when
new. Weakened cells in an aged battery pack are no
longer capable of meeting the high power requirements
and therefore pose a safety risk.

5. Do not throw battery packs into an open re. There is a
risk of explosion!

6. Do not ignite the battery pack or expose it to re.

After Sales Support EMAIL: [e-mail]: [phone]

7. Do not exhaustively discharge batteries. Exhaustive
discharge will damage the battery cells. The most
common cause of exhaustive discharge is lengthy
storage or non-use of partly discharged batteries. Stop
working as soon as the performance of the battery falls
noticeably or the electronic protection system triggers.
Place the battery pack in storage only after it has been
fully charged.

8. Protect batteries and the tool from overloads. Overloads
will quickly result in overheating and cell damage inside
the battery housing without this overheating actually
being apparent externally.

9. Avoid damage and shocks.
Replace batteries which have been dropped from a height
of more than one meter or which have been exposed to
violent shocks without delay, even if the housing of the
battery pack appears to be undamaged. The battery cells
inside the battery may have suered serious damage.
In this respect, please also read the waste disposal
information.

10. If the battery pack suers overloading and overheating,
the integrated protective cut-o will switch o the
equipment for safety reasons.
Important. Do not press the ON/OFF switch any more if
the protective cut-o has actuated. This may damage the
battery pack.

11. Use only original battery packs. The use of other batteries
may result in injuries, explosion and a re risk.

Information on chargers and the charging process

1. Please check the data marked on the rating plate of the
battery charger. Be sure to connect the battery charger
to a power supply with the voltage marked on the rating
plate. Never connect it to a dierent mains voltage.

2. Protect the battery charger and its cable from damage
and sharp edges. Have damaged cables repaired without
delay by a qualied electrician.

3. Keep the battery charger, batteries and the cordless tool
out of children’s reach.

4. Do not use damaged battery chargers.

5. Do not use the supplied battery charger to charge other
cordless tools.

6. In heavy use the battery pack will become warm. Allow
the battery pack to cool to room temperature before
commencing with the charging.

7. Do not over-charge batteries.
Do not exceed the maximum charging times. These
charging times only apply to discharged batteries.
Frequent insertion of a charged or partly charged battery
pack will result in overcharging and cell damage. Do not
leave batteries in the charger for days on end.

5

After Sales Support EMAIL: [e-mail]: [phone]

8. Never use or charge batteries if you suspect that the

last time they were charged was more than 12 months
previously. There is a high probability that the battery

pack has already suered dangerous damage (exhaustive
discharge).

9. Charging batteries at a temperature below 10°C will cause
chemical damage to the cell and may cause a re.

10. Do not use batteries which have heated during the
charging process, as the battery cells may have suered
dangerous damage.

11. Do not use batteries which have suered curvature
or deformation during the charging process or which
show other non-typical symptoms (gassing, hissing,
cracking,…)

12. Never fully discharge the battery pack (recommended
depth of discharge max. 80%) A complete discharge of
the battery pack will lead to premature ageing of the
battery cells.

13. Never charge the batteries unsupervised.

Protection from environmental inuences

1. Wear suitable work clothes. Wear safety goggles.

2. Protect your cordless tool and the battery charger from
moisture and rain. Moisture and rain can cause dangerous
cell damage.

3. Do not use the cordless tool or the battery charger near
vapors and inammable liquids.

4. Use the battery charger and cordless tools only in dry
conditions and an ambient temperature of 10–40°C.

5. Do not keep the battery charger in places where the
temperature is liable to reach over 40°C. In particular, do
not leave the battery charger in a car that is parked in
the sun.

6. Protect batteries from overheating.
Overloads, over-charging and exposure to direct sunlight
will result in overheating and cell damage. Never charge
or work with batteries which have been overheated –
replace them immediately if possible.

7. Storage of batteries, battery chargers and cordless
tools. Store the charger and your cordless tool only in
dry places with an ambient temperature of 10-40°C.
Store your lithium-ion battery pack in a cool, dry place at
a temperature of 10-20°C. Protect them from humidity
and direct sunlight. Only place fully charged batteries in
storage (charged at least 40%).

8. Prevent the lithium-ion battery pack from freezing.
Battery packs which were stored below 0°C for more than
60 minutes must be disposed of.

9. When handling batteries beware of electrostatic
charge: Electrostatic discharges cause damage of the
electronic protection system and the battery cells. Avoid
electrostatic charging and never touch the battery poles.

Disposal of batteries

Batteries contain substances harmful to the environment.
Never place batteries in your household refuse, in re or in
water. Batteries should be collected, recycled or disposed of
in an environmentally friendly way. Seek advice on correct
disposal from local waste authorities.

When shipping or disposing of batteries and cordless tools,
always ensure that they are packed individually in plastic
bags to prevent short circuits and res.

Do not lose this safety information.

6

After Sales Support EMAIL: [e-mail]: [phone]

3. CHARGER OPERATING INSTRUCTIONS

1

2 3

4

11

5

4

b

10a9

7

After Sales Support EMAIL: [e-mail]: [phone]

For use in dry rooms only

Safety Class II

Output connector of the charging unit (direct
current): The outer part of the connector is the
negative pole and the inner part is the positive pole.

3.1 CHARGER SAFETY RULES

CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and
instructions may result in an electric shock, re and/or serious
injury.

Keep all safety regulations and instructions in a safe place
for future use.

a) The charging unit is not allowed to be used for non-

rechargeable, normal batteries.

b) Sucient ventilation is required.

c) The current and voltage information on the battery pack

must be the same as that on the charging unit.

d) Do not expose the charging unit to water or rain.

e) Do not throw old or damaged batteries into water or re.

Follow the environmental protection directives.

f) A defective or no longer chargeable battery must

be treated as special waste. Dispose of it at a special
collection point. Do not dispose of it with your normal
household waste or throw it into water or re.

g) Place the charging unit away from all sources of heat.

h) To reduce the risk of electric shock, pull the power plug

out of the socket outlet by the plug itself and not by the
cable when you want to disconnect the charging unit
from the power supply.

i) Do not take the charging unit apart. Take it to an

authorized repair center if servicing or repairs are needed.
Incorrect assembly can result in an electric shock, re or
even death.

j) This equipment is not designed to be used by people

(including children) with limited physical, sensory or
mental capacities or those with no experience and/
or knowledge unless they are supervised by a person
who is responsible for their safety or they have received
instructions from such a person in how to use the
equipment safely.

k) Children must always be supervised in order to ensure

that they do not play with the equipment.

3.2 LAYOUT FIG. 1+3

11. 1 hour charger

4. Battery pack

9. ON/OFF button for Battery capacity indicator

10. Battery capacity indicator

3.3 TECHNICAL DATA

Charging unit:

Input: 230-240V~50-60Hz, 40W
Output: 14.4-18V d.c., 1.5 A

3.4 OPERATION

3.4.1 Charging the Li-Ion battery pack (Fig. 1-2)

1. Press the pushlock button (5) and pull the battery pack (4)
out of the equipment as shown in Fig. 2.

2. Check that your mains voltage is the same as that marked
on the rating plate of the battery charger. Insert the
power plug of the charger (11) into the mains socket
outlet. The green LED (a) will then begin to ash.

3. Slide the battery pack onto the charger. The red LED (b)
will light up to indicate that the battery pack is being
charged. When the charging is nished, the green LED (a)
will shine with a steady light. Discharged battery packs
require approx. 1 hour for charging. The temperature of
the battery may rise slightly during the charging. This is
normal.
If both LEDs (a, b) ash after the battery pack has been
inserted, the battery pack is defective. In this case pull out
the charger plug immediately and remove the defective
battery pack. Do not use the defective battery pack again.
If both LEDs (a, b) light up after the battery pack has been
inserted, the charging temperature is either low or too
high. In this case, pull out the mains plug of the charger
and charge the battery in an environment in which the
temperature is either warmer or colder.

If the battery fails to charge, please check

• whether there is voltage at the socket outlet

• whether there is good contact at the charging contacts of

the charging unit

If the battery still fails to charge, please call our customer
service hotline on 1300 922 271.

Timely recharging of the battery will help it serve you well for
a long time. You must recharge the battery when you notice
that the power of the cordless product drops.

3.4.2 Battery capacity indicator (Fig. 3/Item 10)

Press the button for the battery capacity indicator (9). The
battery capacity indicator (10) indicates the charge state of
the battery as indicated on the label.

8

After Sales Support EMAIL: [e-mail]: [phone]

3.5 CLEANING AND
MAINTENANCE

Always pull out the power plug before starting any cleaning
work.

The equipment is not allowed to be stored in a damp location
or where there are caustic gases. Keep it in a dry place out of
the reach of children.

3.5.1 Cleaning

Keep the surface of the equipment clean and wipe it only
with a dry cloth.

3.5.2 Maintenance

There are no other parts inside the equipment which require
maintenance.

The equipment is not allowed to be taken apart. If the
equipment is damaged, contact your supplier or the
manufacturer.

3.6. DISPOSAL AND RECYCLING

The equipment is supplied in packaging to prevent it from
being damaged in transit. The raw materials in this packaging
can be reused or recycled. The equipment and its accessories
are made of various types of material, such as metal and
plastic. Defective components must be disposed of as special
waste. Ask your local council.

9

After Sales Support EMAIL: [e-mail]: [phone]

4. CORDLESS IMPACT DRIVER OPERATING INSTRUCTIONS

1

1

5

2

4

3

6

2

5

4

3

3

2

10

After Sales Support EMAIL: [e-mail]: [phone]

4

1

11

After Sales Support EMAIL: [e-mail]: [phone]

4.1 CORDLESS IMPACT DRIVER
SAFTEY RULES

CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and
instructions may result in an electric shock, re and/or serious
injury.

Keep all safety regulations and instructions in a safe place
for future use.

Hold the equipment by the insulated handles when
carrying out work during which the screw or the plug-in
tool could strike concealed power cables. Contact with a live

cable may also make the metal parts of the equipment live
and cause an electric shock.

Ensure that the tool is switched o before
you insert the battery. Inserting a battery into
an electric tool that is switched on can cause
accidents.

4.2 LAYOUT FIG. 1

1. Bit chuck

2. Forward/ Reverse switch

3. ON/OFF switch

4. Battery pack

5. Pushlock button

6. LED

4.3 ITEMS SUPPLIED

• Open the packaging and take out the equipment with

care.

• Remove the packaging material and any packaging and/

or transportation braces (if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport

damage.

• If possible, please keep the packaging until the end of the
warranty period.

IMPORTANT

The equipment and packaging material are not toys. Do not
let children play with plastic bags, foils or small parts. There
is a danger of swallowing or suocating!

CONTENTS

• 1 x Cordless impact driver

• 1 x Battery charger

• 2 x Battery pack

• 1 x Instruction Manual

• 1 x Quick Start Guide

• 1 x Warranty Card

• 1 x Warranty Sticker

4.4 PROPER USE

The cordless drill/screwdriver is designed for tightening and
undoing screws, as well as for drilling in wood, metal and
plastic.

The machine is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user
/ operator and not the manufacturer will be liable for any
damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for
use in commercial, trade or industrial applications.
Our warranty will be voided if the machine is used in
commercial, trade or industrial businesses or for equivalent
purposes.

4.5 TECHNICAL DATA

Voltage supply: 18 V d.c.
Idling speed: 0-2200 rpm
Number of impact: 0-3300 bpm
Bit chuck: 1/4“ (6.35 mm)
Forward and reverse rotation: yes
Screw bit length: 50 mm

Sound and vibration

Sound and vibration values were measured in accordance
with EN 60745.

LpA sound pressure level: 84.13 dB(A)
KpA uncertainty: 3 dB
LWA sound power level: 95.13 dB(A)
KWA uncertainty: 3 dB

Caution - Read the operating instructions to
reduce the risk of injury

Wear ear-mus.
The impact of noise can cause damage to
hearing.

Wear a breathing mask.
Dust which is injurious to health can be
generated when working on wood and other
materials.
Never use the device to work on any materials
containing asbestos!

Wear Safety goggles.
Sparks generated during working or splinters,
chips and dust emitted by the device can cause
loss of sight.

12

After Sales Support EMAIL: [e-mail]: [phone]

After Sales Support EMAIL: [e-mail]: [phone]

Wear ear-mus.

The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.

Impact tightening of fasteners of the maximum capacity
of the tool

Vibration emission value ah = 3.05 m/s²
K uncertainty = 1.5 m/s²

Additional information for electric power tools

Warning!

The specied vibration value was established in accordance
with a standardized testing method. It may change according
to how the electric equipment is used and may exceed the
specied value in exceptional circumstances.

The specied vibration value can be used to compare the
equipment with other electric power tools.

The specied vibration value can be used for initial
assessment of a harmful eect.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance o when it is not in use.

• Wear protective gloves.

Residual risks

Even if you use this electric power tool in accordance with
instructions, certain residual risks cannot be ruled out.
The following hazards may arise in connection with the
equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the
equipment is used over a prolonged period or is not
properly guided and maintained.

4.6 BEFORE STARTING THE

EQUIPMENT

Charge the battery pack with the charger supplied. An empty
battery pack requires a charging period of approximately 1
hour.

For more details about charging the battery pack please read
the operating instructions of the 1-hour charger.

Always remove the battery pack before making adjustments
to the equipment.

Mounting and removing the battery pack
(Fig. 2/Item 4)

Mounting:

Push the battery pack (4) onto the equipment until it latches
in place.

Removing:

Press the pushlock button (5) and pull the battery pack (4) out
of the equipment.

4.7 OPERATION

4.7.1 Forward/Reverse switch (Fig. 3 / Item 2)

With the Forward/Reverse switch above the On/O switch
you can select the direction of rotation of the cordless impact
driver and secure it against being switched on accidentally.
You can choose between clockwise and anticlockwise
rotation. To avoid causing damage to the gearing it is
advisable to change the direction of rotation only when the
tool is at a standstill. The On/O switch is blocked when the
slide switch is in centre position.

4.7.2 On/O switch (Fig. 3 / Item 3)

Innitely variable speed control is possible with the On/O
switch. The further you press the switch, the higher the speed
of the battery-powered impact driver.

4.7.3 Changing the accessory (Fig. 4)

Important. Set the forward/reverse switch (2) to its

centre position whenever you carry out any work (for
example changing the accessory, maintenance work, etc.)
on the cordless impact driver.

• Pull the sleeve on the chuck (1) towards the screw. Insert
the screw bit all the way into the chuck

• Then pull the screw bit slightly until it automatically locks
into place.

4.7.4 Tightening screws

• Plug the required bit in the chuck like mentioned in point

4.7.3

• Select the correct direction of rotation on the Impact
Driver

• Push the drive socket insert onto the screw head and
actuate the ON/OFF switch.

• The tool will operate as a normal screwdriver until the
screw is fully tightened at which point it will operate as a
impact driver.

• It is imperative that you use a torque wrench to check
a torque which has been specied by a manufacturer.
In doing so, ensure that you observe the information
supplied by the manufacturer in the directions for use.

• Most mounting parts can be tightened within a few
seconds. The time required to achieve the maximum
torque depends on the actual case of application and can
be determined with experience.

13

After Sales Support EMAIL: [e-mail]: [phone]

4.7.5 Loosening screws

For as long as the screw is tightened, the tool works as a
impact driver. As soon as the screw is loosened, the tool
operates as a normal screwdriver.

4.8 CLEANING, MAINTENANCE
AND ORDERING OF SPARE
PARTS

Always pull out the mains power plug before starting any
cleaning work.

4.8.1 Cleaning

• Keep all safety devices, air vents and the motor housing

free of dirt and dust as far as possible.

• Wipe the equipment with a clean cloth or blow it with

compressed air at low pressure.

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth and

some soft soap. Do not use cleaning agents or solvents;
these could attack the plastic parts of the equipment.
Ensure that no water can seep into the device.

4.8.2 Maintenance

There are no parts inside the equipment which
require additional maintenance.

4.8.3 Ordering replacement parts

Contact our After Sales Support on 1300 922 271 and quote
the following data when ordering spare parts:

• Type of machine

• Article number of the machine

• Identication number of the machine

• Spare part number of the part required

4.9 DISPOSAL AND RECYCLING

The unit is supplied in packaging to prevent it from being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Contact your dealer or your local council for
disposal requirements.

4.10 STORAGE

Store the equipment and accessories out of children’s
reach in a dark and dry place at room temperature. Never
store the unit below 0 °C. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.

14

After Sales Support EMAIL: [e-mail]: [phone]

15

After Sales Support EMAIL: [e-mail]: [phone]

16

After Sales Support EMAIL: [e-mail]: [phone]

02/2014

Art.Nr: 42.571.74_11013