RIFLES AND CARBINES
General Safety,
Operating Instructions
and Limited Warranty
READ CAREFULLY BEFORE
USING YOUR FIREARM
Important: Keep this manual with your
firearm.
The information contained in this manual
is useful, both for beginners and
experienced shooters. In addition to
important information about functioning,
cleaning and care of the gun, the manual
contains instructions that may be very
helpful in shooting properly.
The most important rule of safe gun
handling is always keep the muzzle
pointed in a safe direction!!!
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
2
Notice:
It is recommended that you record the model number, serial number and
date of purchase of your Taurus firearm for future reference. Be sure to
retain your store receipt and any other documentation that came with
your Taurus.
Model Number ______________________________________
Serial Number ______________________________________
Date of Purchase ____________________________________
Warning
Never allow a minor to shoot without adult supervision. Never leave a
firearm in the possession of a minor. When shooting with a child, make
sure to remain close and safely supervise all activities. If you need to
leave the area, take the firearm and the child with you. Always make sure
to store firearms and ammunition separately.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
3
This Booklet
The safety warnings in this booklet are important. By understanding the
dangers inherent in the use of any firearm, and by taking the precautions
described herein, you can enjoy complete safety in the use of your Taurus
firearm. Failure to heed any of these warnings may result in serious
injury to you or others, as well as severe damage to the firearm or other
property.
Dangerous Weapons
SHOTGUNS, RIFLES and PISTOLS are classified as FIREARMS or
DANGEROUS WEAPONS and are sold by us with the specific
understanding that we are not responsible in any manner whatsoever for
their improper or negligent handling or resale under local laws and
regulations.
Taurus shall not be responsible in any manner whatsoever for
malfunctioning of the firearm, or for physical injury or property damage,
resulting in whole or in part from (1) criminal or negligent discharge,
(2) improper or careless handling, (3) unauthorized modifications, (4)
defective, improper hand-loaded, or reloaded ammunition, (5) neglect,
or (6) other influences beyond our direct and immediate control. This
limitation applies regardless of whether liability is asserted on the basis
of contract, negligence or strict liability (including any failure to warn).
Under no circumstance shall Taurus be liable for incidental or
consequential damages, such as loss of use of property, commercial loss
and loss of earnings or profits.
Warning
Securing your firearm may inhibit access to it in a defense situation and
result in injury or death.
Warning
Failure to properly secure a firearm may result in injury or death.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
4
Safety Warnings
Not Just For Beginners
Regardless of your familiarity or experience with firearms, you need to
study this manual.
The safe handling of firearms requires specialized training, discipline and
caution. Firearms, by their nature and intended function, are deadly
instruments. Accidental death or serious injury can result if they are
handled improperly or carelessly.
Firearms rarely cause accidents. Firearms accidents almost always are
caused by a failure to obey the basic rules of gun safety. Unfortunately,
experienced shooters seem to violate these rules as frequently as
beginners. Thus the basics of safe firearms handling cannot be repeated
too often. Read, re-read and practice the basic principles of firearms
safety until they become second nature: habits that you don’t forget.
If you have any question about your knowledge or ability to use this or
any other firearm with complete safety you should seek supervised
instruction. Personalized instruction is often available from firearms
dealers, gun clubs, state hunter safety programs or police departments in
the United States. If none of these sources is accessible, write to the
National Rifle Association, 11250 Waples Mill Road, Fairfax, VA 22030 or
at www.nra.org. THEY WILL ASSIST YOU.
A person with a firearm in his possession has a full-time responsibility.
He must KNOW how to keep and use his firearm safely, and then must
always TAKE the precautions necessary -all of them. He cannot guess; he
cannot forget. This responsibility is his alone. It cannot be passed off to
someone else.
Remember: no firearm can be made accident-proof. A firearm is just a
machine, with no judgement of its own. It responds to your actions,
whether wise or foolish. The only truly effective safety device is the mind
of a cautious shooter who never forgets that a moment’s carelessness can
produce permanent tragedy.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
5
WARNING
Taurus rifles are manufactured to perform properly with the original
parts as designed. It is your duty to make sure any parts you buy are
installed correctly and that neither replacements nor originals are altered
or changed. Your firearm is a complex tool with many parts that must
relate correctly to other parts. Putting a firearm together wrong or with
modified parts can result in a damaged firearm, danger and injury or
death to you and others through malfunction. Always have a qualified
gunsmith work on your firearm.
WARNING:
To prevent injury or death, it is imperative that you must keep your gun
unloaded, uncocked and securely locked, with ammunition in a separate
location. In addition, take any other reasonable steps to limit the
possibility of theft, crime, accident or suicide.
DANGER:
Protect Your Eyes and Ears
Always wear adequate shooting glasses
and ear plugs or “ear muff” type
protectors whenever you are shooting.
Always make certain that persons close
to you are similarly protected.
Unprotected eyes may be injured by
powder, gas, carbon residue,
lubricant, metallic particles or similar
debris which may emanate occasionally from any firearm in normal use.
Without ear protection, repeated exposure to shooting noise may lead to
cumulative, permanent hearing loss.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
6
Firearms Are Not all Alike
Many makes and models of firearms might LOOK nearly the same.
However, they differ widely in design and operation, and in the location
and function of various controls.
Study this manual thoroughly. Educate yourself on the characteristics and
operation of your particular firearm before attempting to handle it. Do
not permit others to handle it - unless they also have done so.
You should have an instruction manual for every firearm you own. If you
do not, write the manufacturer and obtain one. Most manufacturers will
gladly send you one free. If for any reason a manual is not available, visit
your public library. Many books have been published which contain
detailed information on obsolete or discontinued firearms.
Your knowledge can prevent injuries.
Taurus firearms are designed and made to offer maximum safety when
correctly used. However, as with any other weapon, it is not foolproof,
and may become very dangerous if the following basic recommendations
are not RIGIDLY observed:
Attention
1. DANGER: Never, never-ever point any firearm, loaded or unloaded, at
anything you do not intend to shoot.
2. WARNING: Always treat every firearm as if it were loaded.
3. NOTICE: Get instruction from a competent firearms instructor before
using any firearm.
4. SAFETY FIRST: The safety is only a mechanical device, not a
substitute for common sense.
5. WARNING: Keep your finger off the trigger until you are actually
aiming at the target ready to shoot.
6. WARNING: Be certain the firearm is unloaded before cleaning.
7. WARNING: Always empty firearms before entering a place where
there are people.
8. SAFETY FIRST: Never leave a loaded firearm unattended.
9. SAFETY FIRST: Store firearms and ammunition separately beyond the
reach of children.
10. WARNING: Don’t test the safety by pulling the trigger while the safety
is on unless you are absolutely sure the firearm is empty and you are
pointing the muzzle away from everyone and in a safe direction.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
7
11. SAFETY FIRST: Be sure of your target and backstop before you shoot.
12. SAFETY FIRST: Firearms and alcohol or drugs don’t mix.
13. WARNING: Never pull a firearm towards you by the muzzle. Don’t climb
a tree or cross a fence with a loaded firearm.
14. DANGER: Load and unload with the muzzle pointed in a safe direction.
15. SAFETY FIRST: If a firearm fails to fire when the trigger is pulled, keep it
pointed at the target for at least 30 seconds. Sometimes slow primer
ignition will cause a “hang” fire and the cartridge will go off after a
short pause.
16. SAFETY FIRST: Never shoot at hard flat surfaces or water. Bullet may
ricochet.
17. DANGER: When receiving a firearm always check that it is unloaded
(open breech and inspect the chamber), even if you saw it done
previously.
18. DANGER: Never put your hand over the muzzle of a firearm.
19. DANGER: Check ammunition to be sure it is the right size and caliber,
and that it is not dented.
20. SAFETY FIRST: Use a proper bench or rifle rack and aim the gun only
if you intend to shoot.
21. NOTICE: Never cock the firearm until you are ready to shoot.
22. SAFETY FIRST: Dry firing is bad for this firearm, whether the hammer
block is engaged or not.
23. DANGER: WHILE HANDLING ANY FIREARM, NEVER ALLOW IT TO POINT
AT ANY PART OF YOUR BODY OR AT ANOTHER PERSON. NO HARM
SHOULD RESULT IF YOU OBEY THIS RULE, EVEN IF AN ACCIDENTAL
DISCHARGE OCCURS.
24. CAUTION: If there is any reason to suspect that a bullet is obstructing
the barrel, immediately unload the firearm and look through the bore.
It is not sufficient to merely look in the chamber.
25. SAFETY FIRST: Treat this firearm as a precision instrument.
26. WARNING: Old or reloaded ammunition may be dangerous. We
recommend against using it.
27. DANGER: Don’t try to change your firearm’s trigger pull, because
alteration of trigger pull usually affects sear engagement and may cause
accidental discharge.
28. SAFETY FIRST: Write to us concerning any items or circumstances which
might relate to your safety and the operation of our products.
29. DANGER: Never engage a gun lock on a loaded firearm.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
8
WARNING: Ammunition
1. Use only high quality, original, factory-manufactured ammunition, of
the caliber appropriate to your firearm as indicated on the barrel. Do
not use cartridges that are dirty, wet, corroded, bent or damaged. Do
not oil cartridges. Do not spray aerosol type lubricants, preservatives,
or cleaners directly onto cartridges or where excess spray may flow
into contact with cartridges. Lubricant or other foreign matter on
cartridges can cause potentially dangerous ammunition malfunctions.
Use only ammunition of the caliber for which your firearm is
chambered. The proper caliber is permanently engraved on your
firearm; never attempt to use ammunition of any other caliber.
2. The use of reloaded, “remanufactured”, hand-loaded, or other nonstandard ammunition voids all warranties. Improperly loaded
ammunition voids all warranties. Improperly loaded ammunition can
be extremely dangerous. Severe damage to the firearm and serious
injury to the shooter or to others may result. Always use ammunition
that complies with the industry performance standards established by
the Sporting Arms and Ammunition Manufacturers Institute, Inc., of
the United States, (SAAMI) or the equivalent from other countries.
3. Firearms may be severely damaged and serious injury to the shooter
or to others may result from any condition causing excessive pressure
inside the chamber or barrel during firing. Excessive pressure can be
caused by obstructions in the barrel, propellant powder overloads, or
by the use of incorrect cartridges or defectively assembled cartridges.
In addition, the use of a dirty, corroded, or damaged cartridge can
lead to a burst cartridge case and consequent damage to the firearm
and personal injury from the sudden escape of high-pressure
propellant gas within the firearm’s mechanism.
4. Immediately stop shooting and check the barrel for a possible
obstruction whenever:
•You have difficulty in, or feel unusual resistance in, chambering a
cartridge, or
•A cartridge misfires (does not go off), or
• The mechanism fails to extract a fired cartridge case, or
• Unburned grains of propellant powder are discovered spilled in
mechanism, or
•A shot sounds weak or abnormal. In such cases it is possible that a
bullet is lodged part way down the barrel. Firing a subsequent bullet
into the obstructed barrel can wreck the firearm and cause serious
injury to the shooter or to bystanders.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
9
5. Bullets can become lodged in the barrel.
• If the cartridge has been improperly loaded without propellant
powder, or if the powder fails to ignite (Ignition of the cartridge
primer alone will push the bullet out the cartridge case, but usually
does not generate sufficient energy to expel the bullet completely from
the barrel).
• If the bullet is not properly seated tightly in the cartridge case. When
such a cartridge is extracted from the chamber without being fired,
the bullet may be left behind in the bore at the point where the rifling
begins. Subsequent chambering of another cartridge may push the
first bullet further into the bore.
6. If there is any reason to suspect that a bullet is obstructing the barrel,
immediately unload the firearm and look through the bore. It is not
sufficient to merely look in the chamber. A bullet may be lodged some
distance down the barrel where it can not easily be seen.
IF A BULLET IS IN THE BORE, DO NOT ATTEMPT TO SHOOT IT OUT
BY USING ANOTHER CARTRIDGE, OR BY BLOWING IT OUT WITH A
BLANK OR ONE FROM WHICH THE BULLET HAS BEEN REMOVED.
SUCH TECHNIQUES CAN GENERATE EXCESSIVE PRESSURE, WRECK
THE FIREARM AND CAUSE SERIOUS PERSONAL INJURY.
If the bullet can be removed with a cleaning rod, clean any unburned
powder grains from the bore, chamber, and mechanism before
resuming shooting. If the bullet cannot be dislodged by tapping it with
a cleaning rod, take the firearm to a gunsmith.
7. Dirt, corrosion, or other foreign matter on a cartridge can impede
complete chambering and may cause the cartridge case to burst upon
firing. The same is true of cartridges which are damaged or deformed.
8. Do not oil cartridges, and be sure to wipe the chamber clean of any
oil or preservative before commencing to shoot. Oil interferes with the
friction between cartridge case and chamber wall that is necessary for
safe functioning, and subjects the firearm to stress similar to that
imposed by excessive pressure.
9. Use lubricants sparingly on the moving parts of your firearm. Avoid
excessive spraying of any aerosol firearm care product, especially
where it may get on ammunition. All lubricants and aerosol spray
lubricants in particular, can penetrate cartridge primers and cause
misfires. Some highly penetrative lubricants can also migrate inside
cartridge cases and cause deterioration of the propellant powder; on
firing, the powder may not ignite. If only the primer ignites, there is
danger that the bullet may become lodged in the barrel.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
10
Warning
Never disassemble the safety. It has been correctly designed, fitted and
tested. Any mechanical device can fail, however, so never rely on the
safety to justify careless handling. Never use a firearm with a safety that
does not function properly.
Taurus Security System
Model 62, 72 and 172 Pump Action
This rifle is equipped with the exclusive “TAURUS SECURITY SYSTEM”.
The system is designed to preclude use of the rifle when the mechanism
is engaged. It consists of an integral mechanism located on the back
portion of the hammer. When properly engaged, by use of the key, it
prevents the functioning of the rifle. The engagement of the mechanism
can only be done utilizing a key with a shape that fits the security
mechanism.
1.
Engagement (Secure)
To engage the deactivation mechanism, it is necessary to insert the key
into the deactivation pin and turn it clockwise until a “click” is felt or
heard (Fig. la). In this position, the rifle’s mechanism is locked and the
pin protrudes above the surface of the back of the hammer (Fig. 1b).
2.
Disengagement (Ready-to-Fire)
To place the rifle in a firing condition, one must insert the key in the
security mechanism and turn the key counter clockwise (Fig.2a). In this
position, the top of the pin is on the same plane with the rest of the back
portion of the hammer (Fig. 2b). The rifle is now ready to fire.
Fig. 2a
Fig. 2b
Fig. 1a
Fig. 1b
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
11
Taurus Security System
Model 63 Semi-Auto Action
This rifle is equipped with the exclusive “TAURUS SECURITY SYSTEM”. The
system is designed to preclude use of the rifle when the mechanism is
engaged. It consists of an integral mechanism located on the right rear
portion of the breech bolt, which can be seen in the ejection port of the
receiver. When properly engaged, by use of the key, it prevents the
functioning of the rifle by locking the bolt and the firing pin and obstructing
the movement of the bolt and the firing pin. The engagement of the
mechanism can only be done utilizing a key with a shape that fits the
security mechanism.
1.
Engagement (Secure)
To engage the deactivation mechanism, it is necessary to insert the key
into the deactivation pin (Fig. 1a) and turn it clockwise until a “click” is
felt or heard. In this position, the rifle’s mechanism is locked and the pin
protrudes above the surface of the right rear of the breech bolt (Fig. 1b).
2.
Disengagement (Ready-to-Fire)
To place the rifle in a firing condition, one must insert the key in the
security mechanism (Fig. 2a) and turn the key counter clockwise. In this
position, the top of the pin is on the same plane with the right side of the
breech bolt (Fig. 2b). The rifle is now ready to fire.
Warning
Never tamper with the security system or attempt to use anything other
than the provided special key to operate the security system. Attempting to
defeat the Taurus Security System may damage your firearm. Never use a
firearm on which the Taurus Security System appears to have been
tampered with. Doing so will create a hazardous situation and may
damage the firearm and result in accidental death or serious injury.
Fig. 1a
Fig. 1b
Fig. 2a
Fig. 2b
Warning
Discharging firearms in poorly ventilated areas, cleaning firearms, or
handling ammunition may result in exposure to lead and other
substances known to cause birth defects, reproductive harm, and other
serious physical injury. Have adequate ventilation at all times. Wash hands
thoroughly after exposure.
Pump Action Operating Instructions
(Semi-Automatic instructions on page 17)
How To Operate The Safety
Warning
Prior to firing, know and understand the
operation of the safety by practicing with the
rifle unloaded.
The safety is a lever located on top of the breech
bolt. When the elevated portion of the lever is in
line with the barrel and the red “F” is exposed,
the rifle will fire when the hammer is in fullcock position and the trigger is pulled. When the elevated portion of the
safety lever is turned to the right and is perpendicular to the barrel and
the green “S” is exposed, the rifle will not fire when the trigger is pulled.
Warning
Never put the safety between the Safe and Fire
notches. Unless the safety is positioned in one of
the two notches, you cannot be certain whether it
is on safe or fire.
The safest way to carry this rifle is with NO round
in the chamber. If you feel that you must carry the
rifle with a round in the chamber, then the safety
lever must be on SAFE and the hammer placed in
the half-cocked notch. Then, to fire, the hammer
should be placed in the full-cocked position and
then the safety placed in the fire position.
Safety ON
Safety OFF
Hammer Rest
Hammer Half-Cocked
Hammer Full-Cocked
F
Always keep this rifle on Safe regardless of the position of the hammer,
whether loaded or unloaded. The only time the safety lever should be
placed in the Fire position is when you intend to shoot.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
12
How To Load Your Rifle
Pump Action Magazine Loading
Warning
Never attempt to load your rifle with ammunition that does not meet the
cartridge designation stamped on the barrel. Use only clean, dry, factoryloaded ammunition in the caliber appropriate to your firearm. The
proper caliber is stamped on the barrel.
Warning
Before loading this firearm, always check the bore to be sure it is free of
grease, oil or any other obstruction. Be sure the chamber is empty, bolt is
open and the safety is on SAFE. To avoid having your hands near
the muzzle of a loaded rifle, never add cartridges to a partially loaded
tubular magazine.
Warning
This rifle will not function properly unless the inner magazine tube is
locked securely in place.
Fig. 1
Unlocking the tubular
magazine.
Fig. 2
Loading the tubular magazine.
OPEN THE BOLT by first carefully allowing the hammer to move forward
UNDER CONTROL OF YOUR THUMB while pulling the trigger until the
hammer is in the fully forward (at rest) position, then pull forend smartly to
the rear.
Then, with the safety on SAFE, keeping your fingers away from the muzzle,
turn your rifle upside down and unlock the inner magazine tube by turning
the knurled locking end plug (see Fig. 1). Pull the inner tube out until the
loading port is exposed. Insert the cartridges, bullet end toward the muzzle
(see Fig. 2). When you have loaded up to the stated magazine capacity, shown
in this manual under “Specifications”, slide the tube back in place, turning it
slightly to ease passage over the loaded rounds. DO NOT FORCE THE TUBE
DOWN. Then rotate the knurled locking end plug to the locked position.
Inner tube will not lock in place if the number of cartridges loaded exceeds
the stated magazine capacity.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
13
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
14
Cocked and Ready
To chamber the first cartridge, close the bolt by moving the forend
forward, then cycle the action again. Always keep the safety on SAFE. The
firearm is now cocked and ready to fire.
To Fire
With the firearm pointed at the target, move the safety to the FIRE
position and squeeze the trigger. Open and close the bolt completely for
each repeat shot. If you have not fired all cartridges at the target, be sure
to put the safety on SAFE until you are ready to shoot again.
How To Unload
Pump Action Rifle
With the safety on SAFE, and the rifle pointed in a safe direction, open the
bolt and eject the loaded cartridge from the chamber.
Cycle the action repeatedly by opening and closing the bolt, until the
ejection of cartridges ceases.
Warning
Completely open and fully close the bolt several more times to be certain
that the chamber and feed mechanism are empty. Finally, inspect interior
of receiver visually. Leave the bolt in the open position.
A safer way to unload the rifle is by (1) placing the safety lever on SAFE;
(2) removing the inner magazine tube; (3) pouring out and catching the
cartridges; (4) replacing magazine tube; and (5) cycling action several
times.
ALWAYS INSPECT INTERIOR OF RECEIVER VISUALLY TO MAKE SURE THAT
THE MAGAZINE IS EMPTY AND THE CHAMBER IS EMPTY.
What To Do If Rifle Fails To Fire
1. Misfires: If you squeeze the trigger and the cartridge does not fire,
remain in the shooting position and count to 30. Then operate the
bolt to eject the misfired cartridge from the firearm.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
15
2. Underpowered Shot: An underpowered cartridge is unusual if the
ammunition is fresh, clean, and factory loaded. However, if you hear
an unusual sound or low report, you should stop immediately and
proceed as follows:
Warning
Because the bullet may actually still be in the barrel, you must unload
completely and then with the bolt open, look through the barrel from
the muzzle end to see if there is any obstruction. If there is, it should be
removed by a qualified gunsmith.
Sighting
Your rifle was pre-sighted at the factory. However, due to individual
sighting characteristics, minor adjustments may be necessary.
Always ensure the rifle is pointed in a safe direction. Put the rifle on SAFE
and open the bolt before making any sight changes.
1. VERTICAL CORRECTION (Elevation): To raise the point of impact,
raise the rear sight. To lower the point of impact, lower the rear sight.
The sight can be raised and lowered by moving the stepped elevator
forward and back with your thumb.
2. HORIZONTAL CORRECTION (Windage): To move the point of impact
to the left, move the rear sight base to the left. To move the point of
impact to the right, move the rear sight base to the right.
Windage adjustments to the rear sight can be made by gently tapping
the dovetail portion of the rear sight in the desired direction.
How To Clean Your
Pump Action Rifle
Warning
Before cleaning your rifle, be certain it is completely unloaded, and the
bolt has been opened.
Never attempt to wipe down or clean a loaded firearm. Follow
instructions under “How to Unload” before cleaning.
Figure 1 - Open Bolt
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
16
With normal use it is not necessary to clean the bore of your rifle.
However, if the rifle gets wet or if foreign material gets into the action or
barrel, cleaning as described below is recommended.
Being sure your rifle is unloaded and pointed in a safe direction with the
safety on SAFE, cycle the bolt to the rear, as shown in Fig. 1.
Clean the bore and barrel by using any standard .22 caliber commercial
cleaning rod and cleaning patches. Clean the barrel with powder solvent
and wipe lightly with firearm oil after cleaning.
Warning
Further disassembly of the action is not recommended and should only
be attempted by a qualified gunsmith.
Pump Action Rifle
Take Down Instructions
If you wish to “take down” your rifle for transport or storage, proceed as
follows:
1. Place safety lever on.
2. Make sure rifle is unloaded.
3. Place hammer in “half-cocked” position.
4. Unscrew the knurled knob on left rear of receiver until it turns freely.
5. Pull butt stock and rear of receiver to rear.
6. Reassemble in reverse order.
Use a very thin coat of light oil during below freezing conditions.
Condensation droplets will form soon after the firearm is brought into a
warm room, or it may become wet during inclement weather. In any
case, all moisture should be removed. Exterior metal finishes may be
wiped down with a slightly oiled cloth. For long term storage, lightly oil
the bore, barrel and action with firearm oil. Your firearm should be
completely unloaded and stored in a dry area. Never store your firearm
in a carrying case.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
17
Semi-Automatic Operating
Instructions
(Pump Action instructions on page 12)
How To Operate The Safety
Warning
Prior to firing, know and understand the operation of the safety by
practicing with the rifle unloaded.
The Taurus Model 63 Rifle is equipped with a
cross bolt type safety. The safety control is
located on the rear of the trigger guard. The
control is a button that can be operated easily
with gloved hands as well as barehanded. When
the safety is in the “ON” or “Safe” position, the
trigger is blocked from movement and the rifle
cannot be fired with a normal trigger pull. It is
essential to safe shooting that you become
familiar with the operation of the safety before shooting the rifle.
The safety is in the “ON” or “Safe” position when the button is pushed
fully to the right.
Warning
No safety mechanism is a substitute for safe firearm practices. Do not
rely solely on the safety mechanism to prevent accidental discharges.
When shooting is not imminent, it is advisable to keep the chamber
empty. DO NOT load a round into the chamber until ready to shoot and
in a safe shooting position. Even with the safety engaged, always keep the
muzzle pointed in a safe direction and your finger well clear of the
trigger. The safety mechanism may not prevent an accidental discharge if
the rifle is dropped or jarred. Failure to observe safe shooting practices
may result in accidental death or serious injury.
Safety First
Always keep the action locked open and the ammunition magazine empty
until ready to shoot in a safe situation. Do not transport or store the rifle
in a loaded condition. Store ammunition separately.
Safety
Control
Button
18
Loading Your Semi-Automatic Rifle
Warning
Never attempt to load your rifle with ammunition that does not meet the
cartridge designation stamped on the barrel. Use only clean, dry, factoryloaded ammunition appropriate to your firearm. The correct caliber is
stamped on the barrel.
Warning
Before loading this firearm, always check the bore to be sure it is free of
grease, oil or any other obstruction.
Be sure the chamber is empty,
action is closed and the safety is in the “ON” or “SAFE” position. This
rifle will not function properly unless the magazine tube is locked
securely in place in the butt stock.
Twist the end of the magazine tube approximately 1/8 turn counter-clockwise
to unlock. Slowly pull the tube out, observing the loading port on the right
side of the stock. Pull the magazine tube out until the magazine follower at the
end is clear of the loading port. Do not completely remove the tube from the
stock.
Point the muzzle in a safe direction and slightly downward. Insert the
cartridges, bullet end facing the muzzle, into the loading port one at a time
and allow them to slide forward in the internal magazine. Load only 10
rounds of ammunition into the rifle.
Once the ten rounds are loaded, gently, but firmly push the magazine tube
into the butt stock until it is completely seated. Turn the tube clockwise until it
locks firmly into place. This should be done carefully as the magazine tube is
spring loaded and the rifle now contains live ammunition.
Warning
Do not attempt to load this rifle beyond its stated capacity of ten rounds.
Your rifle is now loaded. Exercise extreme caution in handling. If you
need to leave the firearm, unload it first.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
Magazine Tube
Loading Port
Safety Control Button
Operating Your Semi-Automatic Rifle
Warning
These steps should be practiced with an empty rifle at a proper shooting
facility always keeping the muzzle pointed in a safe direction.
Once the rifle is loaded and the safety is in the “ON” or “SAFE” position,
the chamber may be loaded. Be sure the muzzle is pointed in a safe
direction and your finger is well clear of the trigger. To load the chamber,
push the bolt operation plunger rearward until it stops. This will cause the
ejection port to open. Release the plunger and allow it to move back to its
forward position. This will load a cartridge into the chamber.
Warning
Your rifle is now loaded and has a round chambered. Keep the muzzle
pointed in a safe direction at all times, the safety in the “ON” or “SAFE”
position and your finger well clear of the trigger until on target and ready
to shoot. Do not carry, throw or drop the rifle with a loaded chamber.
Failure to observe these precautions may result in accidental death or
serious injury.
Firing Your Semi-Automatic Rifle
Once you are in a safe shooting position, have the muzzle pointed in a safe
direction and are safely on target, release the safety by pressing the Safety
Control Button towards the left. Be sure to keep your finger off the trigger
until ready to shoot. When ready to shoot, smoothly and gently pull the
trigger until the rifle discharges. The semi-automatic action will eject the
spent case and load a fresh round into the chamber.
Warning
Ejected cases can exit the Ejection Port at high speed and will be hot. Be
certain that there is nobody to the right of the rifle as the case will be
ejected in that direction.
Ejection Port
Safety Control Button
Bolt Operation Plunger
Rearward
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
19
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
20
Locking the Semi-Automatic Action
Warning
These steps should be practiced with an empty rifle at a proper shooting
facility always keeping the muzzle pointed in a safe direction.
The action on the Taurus Model 63 may be locked in the open position
for cleaning, inspection and safe transport. To lock the action, make sure
the muzzle is pointed in a safe direction and the safety is in the “ON” or
“SAFE” position. Push the Operating Plunger rearward until it stops. With
the plunger in the full rearward position, twist the plunger clockwise
approximately 1/2 turn. The plunger will not turn past this position. The
action is now locked open.
The action can be closed by turning the plunger in the opposite direction.
It will return to the forward position.
Warning
Closing the port will chamber a round if there are any cartridges in the
magazine. Always have the safety in the “ON” or “Safe” position and the
muzzle pointed in a safe direction.
Warning
Do not carry the rifle by inserting finger(s) into the ejection port. Should
the port close you may damage your firearm and/or cause serious injury
to yourself.
Unloading Your Rifle
With the safety in the “ON” or “Safe” position and the action closed,
remove the magazine tube completely from the rifle. Carefully, while
keeping the muzzle pointed in a safe direction and your finger well clear
of the trigger, tip the rifle muzzle-up and allow the cartridges to drop into
an appropriate container. Replace the magazine tube and with the safety
in the “ON” or “Safe” position, work the Operating Plunger several times
to ensure no cartridges are in the chamber or remaining in the magazine.
Visually inspect the loading area and chamber to make sure no
ammunition is present.
Warning
These directions must be followed precisely. Any deviation or variance may
damage your firearm and can result in accidental death or serious injury.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
21
Disassembly/Takedown/Cleaning of
the Semi-Automatic Rifle
Warning
Before disassembling your rifle, make sure that there are no cartridges in
the magazine and that the chamber is clear. Disassembling the rifle with
cartridges in the magazine and/or chamber can damage your gun and may
result in accidental death or serious injury.
The Taurus Model 63 can be disassembled or taken down into 2 parts for
easy storage, cleaning and transport. To begin the take down process,
remove the magazine tube completely from the butt stock. Loosen the
takedown screw until it is fully loose in the frame. The screw will not come
out completely. Once the takedown screw is fully loosened, gently pull the
stock away from the barrel. Do not force them apart. The rifle will separate
into 2 pieces, exposing most of the inner workings for inspection and
cleaning.
The rifle may now be cleaned with any firearm cleaning solvent. You should
use very little solvent, being careful not to drip onto the wooden stocks.
Once the rifle is clean, a light coating of firearm oil should be applied to
metal surfaces. Do not over oil the firearm as this can lead to an
accumulation of dirt and may cause a malfunction.
Warning
Do not disassemble the rifle any further than shown in these instructions.
Further disassembly of the action is not recommended and should only be
attempted by a qualified gunsmith. Attempting to further disassemble the
rifle may permanently damage the firearm and can lead to accidental death
or serious injury from an unintended malfunction.
Reassembling Your
Semi-Automatic Rifle
Carefully slide the receiver/barrel into the end of the butt-stock portion.
The pieces should go together easily. Do not force. Once the pieces are
together, tighten the takedown screw to a fair amount of finger tightness. Do
not use tools for further tightening. Reinsert the magazine tube after
verifying that there are no cartridges in the rifle.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
22
Repair Instructions
Your firearm has been designed, engineered and manufactured in
accordance with Taurus’ rigid quality control standards. However, any
mechanical device may occasionally require adjustment or repair.
Taurus Service Policy
Before shipment, your firearm was carefully inspected and test fired in
order to ensure that it conformed to our specifications and standards.
Should your firearm require adjustment or repair, we strongly
recommend that you return it to Taurus for factory service.
If there is any question regarding the performance of your firearm,
please write to our Service Department fully describing all circumstances
and conditions involved. If our Service Department makes the
determination that your firearm requires factory service, you will be so
advised and will be given instructions for the most expeditious handling
of your shipment.
Our Service Department will give your firearm a complete inspection, and
evaluate the problem (s) specified in your letter. If the work required is
not covered under the terms of our “Warranty” (when applicable) you
will receive an actual cost quotation, not an estimate. Any charge for
repair work must be authorized by you, and no work will be done
without your expressed approval.
Please follow these suggestions to expedite service in the United States of
America to return any firearm to us for adjustment or repair.
1. Federal law permits you to return your firearm to the manufacturer for
service via common carriers. However, state and local firearms laws vary
greatly; you should consult your local prosecuting attorney regarding any
restrictive laws in your jurisdiction regarding your shipment or receipt of
firearms. With the above in mind, it is strongly recommended that any
firearm sent to us for repair be sent through a Federally licensed dealer.
2. All firearms must be shipped to us prepaid. WE WILL NOT ACCEPT
COLLECT SHIPMENTS.
Ship to: Taurus Customer Service, 16175 N.W. 49 Ave., Miami, FL 33014.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
23
SAFETY FIRST:
Parts
All firearms require periodic maintenance and inspection which may reveal a
need for adjustment or repair. Have your firearm checked by a competent
gunsmith annually, even if it seems to be working well, since breakage,
improper functioning, undue wear, or corrosion of some components may not
be apparent from external examination. If you notice ANY mechanical
malfunction, do NOT continue to use the firearm. UNLOAD the firearm and
take it to a competent gunsmith immediately.
Our Service Department maintains a full complement of replacement parts for
our firearms of current manufacture. Even though most gunsmiths have the
knowledge, training and ability to make the necessary repairs to your firearm,
the skill and workmanship of any particular gunsmith is totally beyond our
control. Should your firearm ever require service, we strongly recommend that
you return it to Taurus. Follow the instructions outlined below. Remember,
unauthorized adjustments or parts replacement can void your warranty. It is
the responsibility of the purchaser to be absolutely certain that any parts
ordered from Taurus are of the correct type and are properly fitted and
installed by a competent person.
THIS FIREARM IS A PRECISION
MECHANISM AND THE IMPROPER FITTING OF PARTS OR IMPROPER
MECHANICAL ADJUSTMENT MAY RESULT IN A DANGEROUS MALFUNCTION,
DAMAGE TO THE FIREARM, AND POSSIBLE SERIOUS INJURY TO THE SHOOTER
OR TO OTHERS.
Therefore, the purchaser and/or installer of parts must
accept full responsibility for the correct adjustment of and function of the
firearm after such installation has been made or attempted.
3. Be sure to enclose a letter stating your name, address and telephone
number, serial number, caliber and barrel length of your firearm. Also
state nature of trouble experienced or work required. Merely stating
“defective” or “repair as necessary” is inadequate information. Be
specific and enclose copies of any previous correspondence. Work (other
than warranty repair) will bear minimum labor charge of $ 10.00.
4. FIREARMS MUST BE SHIPPED UNLOADED. Double check the chamber
of your firearm before shipping. If firearms are sent to Taurus in a loaded
condition, we are required by law to notify the Federal authorities.
5. DO NOT include telescopic sights; custom grips, holsters, or other
accessories with any firearm shipped to us.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
24
Exploded Diagram - Pump Action
Model 62, 72 and 172
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
25
BARREL ....................................1
FRONT SIGHT ..........................2
FRONT MAGAZINE RING.........3
REAR MAGAZINE RING............4
REAR MAGAZINE RING PIN ....5
REAR SIGHT ASSEMBLY............6
REAR SIGHT SUPPORT.............7
REAR SIGHT BLADE .................8
REAR SIGHT RIVET ..................9
REAR SIGHT ELEVATOR .........10
MAGAZINE TUBE LINER.........11
MAGAZINE TUBE....................12
MAGAZINE PLUG PIN ............13
MAGAZINE SPRING................14
MAGAZINE FOLLOWER .........15
MAGAZINE PLUG ...................16
RECEIVER ...............................17
SAFETY PIN ............................18
SLIDE PLATE...........................19
SLIDE PLATE SCREW..............20
ASSEMBLY SCREW..................21
ASSY SCREW STOP PIN..........22
BREECH BOLT ASSY ...............23
BREECH BOLT ........................24
FIRING PIN BUSHING........... 25
FIRING BUSHING PIN ............26
EXTRACTOR...........................27
FIRING PIN STOP...................28
EXTRACTOR PIN....................29
SAFETY ...................................30
SAFETY SPRING .....................31
SAFETY SPRING BALL ............32
HAMMER SPRING
SUPPORT PIN.......................33
FIRING PIN SPRING ...............34
FIRING PIN.............................35
CARRIER................................ 36
CARRIER LEVER .....................37
CARRIER LEVER PIN ..............38
CARRIER LEVER SPRING........39
CARRIER LEVER
SPRING SCREW................... 40
HAMMER ASSY .......................41
KEY LOCK..............................42
KEY LOCK SPRING ................43
KEY LOCK BALL.....................44
FRAME ....................................45
ASSY SCREW BUSHING..........46
TRIGGER ................................47
TRIGGER SPRING...................48
TRICEER PIN ..........................49
STOCK/GUARD SCREW .........50
HAMMER SPRING GUIDE ......51
HAMMER SPRING...................52
HAMMER SPRING
SUPPORT..............................53
STOCK ....................................54
BUTT PLATE ...........................55
BUTT PLATE SCREW ..............56
FOREND .................................57
FOREND SCREW ....................58
PRESSURE WASHER ................59
FOREND BUSHING.................60
ACTION SLIDE........................61
ACTION LEVER.......................62
ACTION LEVER PIN................63
ACTION LEVER TUBE .............64
Parts List for Pump Action
Model 62, 72 and 172
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
26
Exploded Diagram - Semi Automatic
Model 63
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
27
BARREL................................1
FRONT SIGHT .....................2
REAR SIGHT ASSY ...............3
(Includes #4, #5 and #6)
REAR SIGHT BLADE ............4
REAR SIGHT SUPPORT .......5
REAR SIGHT RIVET.............6
REAR SIGHT ELEVATOR......7
MAGAZINE TUBE LINER .....8
MAG TUBE WASHER ............9
MAGAZINE TUBE NUT......10
MAGAZINE TUBE...............11
(Includes #12, #13, #14, #15
and #16)
TUBE..................................12
(Includes #12, #13, #14, #15
and #16)
MAGAZINE FOLLOWER ....13
MAGAZINE SPRING ..........14
MAGAZINE PLUG..............15
MAGAZINE PLUG PIN.......16
RECEIVER ..........................17
RECEIVER BUSHING .........18
EJECTOR............................19
MAG BREECH BOLT ..........20
(Includes #21, #22, #23, #24,
#25, #26 and #27)
BREECH BOLT ...................21
FIRING PIN SPRING..........22
FIRING PIN........................23
FIRING PIN PIN ................24
EXTRACTOR......................25
PLUNGER ..........................26
PLUNGER SPRING.............27
KEY LOCK.........................28
KEY LOCK PIN..................29
KEY LOCK BALL ...............30
KEY LOCK SPRING...........31
RECOIL SPRING ................32
RECOIL SPRING GUIDE ....33
FOREND ............................34
FOREND CAP SUPPORT ...35
FOREND CAP ASS´Y .........36
FOREND CAP ....................37
FOREND CAP PIN .............38
FOREND SCREW ...............39
ACTION SLIDE SPRING.....40
ACTION SLIDE ..................41
ACTION LEVER BUTTON..42
ACTION LEVER
BUTTON PIN .................43
FEEDER..............................44
AMMUNITION
RETAINER........................45
AMMUNITION RETAINER
SPRING............................46
AMMUNITION RETAINER
PIN ..................................47
HAMMER SPRING ASS´Y...48
HAMMER ...........................49
HAMMER SPRING GUIDE .50
HAMMER SPRING .............51
HAMMER SPRING PLATE..52
HAMMER SPRING
GUIDE PIN ......................53
FRAME ...............................54
TRIGGER PIN ....................55
HAMMER PIN ....................56
AMMUNITION RETAINER
PIN ..................................57
ASSEMBLY SCREW
PLUNGER ..........................58
ASSEMBLY SCREW ............59
ASSEMBLY SCREW
RETAINER........................60
TANG SIGHT SCREW ........61
TRIGGER SPRING..............62
TRIGGER SAFETY..............63
TRIGGER ...........................64
SEAR ..................................65
SEAR SPRING ....................66
STOCK...............................67
BUTT PLATE......................68
BUTT PLATE SCREW.........69
FEEDER ASS´Y ...................70
Parts List for Semi Automatic
Model 63
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
28
Taurus Limited Warranty
What Does This Warranty Cover?
This warranty covers any service and repair needed by any product
manufactured by Forjas Taurus SA., and imported by Taurus International
Manufacturing, Inc. or manufactured in the United States by Taurus
International Manufacturing, Inc.
How Long Does Coverage Last?
This warranty is of unlimited duration.
What Will We Do?
Taurus will service and/or repair all covered products free of charge.
What Does This Warranty Not Cover?
This warranty does not cover stocks, forends, sights, accessories,
cosmetic defects after one year, or damage caused by customer abuse at
any time. This express limited warranty is the only warranty on this
product. This product is sold “as is” and has no implied warranties of
merchantability or fitness for a particular purpose. There are no
warranties which extend beyond the description on the face hereof.
How Do I Get Service?
To simplify repair and service Forjas Taurus and Taurus International
products are serviced and repaired by Taurus International. Questions
regarding the products of either company can be directed to Taurus
International in Miami, Florida at 1-305-624-1115 or in writing to:
16175 NW. 49th Avenue
Miami, Florida 33014
in care of the Consumer Affairs Department.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
29
Model Caliber Capacity Barrel Overall Weight Finish
Length Length
M62R .22 LR 14 23” 39” 79.4 oz. B
SS
M62C .22 LR 12 16-1/2” 32-1/2” 74 oz. B
SS
M72R .22 12 23” 39” 79.4 oz. B
MAGNUM SS
M72C .22 10 16-1/2” 32-1/2” 74 oz. B
MAGNUM SS
M172R .17 HMR 10 23” 39” 79.4 oz. B
SS
M172C .17 HMR 10 16-1/2” 32-1/2” 74 oz. B
SS
M63 .22LR 10 23” 39” 79.4 oz B
SS
Model Specifications
B = Blue
SS = Stainless Steel
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
30
© Copyright 2002 Taurus International Manufacturing, Inc.
The information in this manual is provided as guidelines and directions for the
safe use of your firearm.Taurus can not be held responsible for the misuse,
illegal or negligent use of our products.We strongly encourage all firearms
owners to observe all firearms safety rules.
Keep this and all firearms and ammunition away from unsupervised children.
Firearms safety is everyone’s responsibility.
rev. 12/02
This trademark, forged for over 60 years of hard and
dedicated work, became a symbol of quality in handguns for
civilian, police and military use. This outstanding quality is the
result of constant technological evolution and from the
devoted work of expert gunsmiths and highly specialized
professionals, which makes TAURUS a respected name in
more than 75 countries all over the world.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
31
This page intentionally left blank
A WORD TO THE WISE
MOST FIREARMS ACCIDENTS HAPPEN
BECAUSE THE SHOOTER CARELESSLY
VIOLATES THE SINGLE MOST
IMPORTANT RULE OF SAFE FIREARM
HANDLING:
ALWAYS KEEP THE MUZZLE POINTED
IN A SAFE DIRECTION!
IMPORTANT:
DO NOT DISCARD
KEEP THIS MANUAL WITH YOUR
FIREARM. UPON CHANGE OF
OWNERSHIP, TRANSFER THIS
MANUAL WITH THE FIREARM.
12/02
Forjas Taurus, S.A
Av. do Forte, 511 - Cx. Postal 44 - Telegr.: “Forja”
Fone: 551.3347.4000 - Fax: 551.3021.3110
91360-000 - Porto Alegre - RS - Brasil
Taurus International Manufacturing, Inc.
16175 NW 49 Avenue
Miami, Florida 33014
Telephone: (305)624.1115 - Fax: (305)624.1126
Loading...