User's Guide
1. Company Name : Tau Corp
2. Equipment Name (Model Name): Low Power Wireless Equipment (Equipment
for Wireless Data Communication Systems)
Model Name : TSP-V10
3. Manufacturing date : 2018 year
4. Manufacturer/Manufacturing country : Tau Corp / Republic of Korea
5. Authentication number :
SwingPutt Product Configuration
□ SwingPutt Sensor and Fixing Silicon Rubber Band
□ USB cable for charging
□ USB Wireless Communication Dongle
(Using Certified Wireless Dongle)
□ Installation Software DVD-ROM or USB Flash Memory
No. Name Function
1 User Button 1
Device reset Button
When users press and release the User Button 1, the device resets and
blinking green LED. This button is used when users switch the device from
the Shutdown Mode to the Normal Operation Mode, or when resolving
problems concerned device operation. In the Normal Operation Mode, the
LED flashes. When the Bluetooth connection is not made, the red LED
flashes, and when the connection is made in a normal way, the green LED
blinks on and off.
2 User Button 2
This button is used to select the club outside the green or adjust the
putting direction on the green.
This button is also used to switches the device from normal operation mode
to shutdown mode with the User Button 3 or switches the device from
shutdown mode to normal operation mode.
3 User Button 3
This button is used to select the club outside the green or adjust the
putting direction on the green.
This button is also used to switches the device from normal operation mode
to shutdown mode with the User Button 2 or switches the device from
shutdown mode to normal operation mode.
4 LED Indicator
The LED Indicator allows users to recognize the status of the Device
through LED.
Red LED Flash: The red LED flash indicates that the Device is in the
Normal Operation Mode but the Bluetooth connection is not set.
Green LED Flash: The green LED flash indicates that the Device is in the
Normal Operation and the Bluetooh connection is normal.
Green LED Light: The green LED light indicates that the Device is in the
Normal Operation Mode, the Bluetooth connection is normal, and preparation
for acquiring swing information by users is completed.
5
USB Charging
Connector Port
The USB charging connector port is a port to connect the USB cable for
charging which is needed to charge an internal battery.
6
Fixing silicon
rubber band
The band is used to attach and fix the device to the club shaft.
How to Connect the Enclosed Wireless USB Communication Dongle to Your Computer
Wireless-connect the product of SwingPutt to your computer as shown below:
Install the software provided with the product before connecting the wireless USB
communication dongle. Put the wireless USB communication dongle into a USB port on your
computer after installing the software. Press the Button 1 of the product to turn on the
Device. The dongle and the product will be automatically connected.
Any USB port on your computer can be used.
SwingPUTT Product specifications
Specifications Etc
Power DC 5V
power supply voltage in charging.
When using the device internal
battery is used.
Power consumption < 500 mA
Maximum current in charging.
When using device < 20 mA.
Product size 22mm×50mm×38mm With Clip
operating temperature 5 ∼ 35 ℃
External terminal Battery charging terminal
Frequency of use (GHz) 2.402 ∼ 2.480
- CAUTION -
Note: This equipment has been tested and found to comply with the limit for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential Installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions. may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on,
the user is encourage to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
- Consult the dealer or an experience radio/TV technician for help
※ Change or modification not expressly approved by the party responsible for Compliance
could void the user’s authority to operate the equipment
Caution
Modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator
and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Antenna Type: Chip Antenna
Antenna Gain: 0.5 dBi
Loading...