How it Works
Tatung
Loading...
100
User Manual
56 pgs3.64 Mb0

Tatung 100 User Manual

Download
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 1 Introduction.........................................................................................................................3
1.Features and Specification................................................................................................4
2.Appearance........................................................................................................................6
1.Front View and Keypad function..............................................................................6
2.Back V iew.................................................................................................................8
3.Specification of connector ........................................................................................9
Chapter 2 Operating Procedure – LCD Display Configuration.........................................................10
Chapter 3 Advanced Configurations via Telnet.................................................................................17
Chapter 4 Web Configuration.........................................................................................................33
Step 1. Browse the IP Address predefined via RS-232..............................................................33
Step 2. Input the login name and password ...............................................................................34
Step 3. The web interface main screen.......................................................................................34
1.Network Interface ...........................................................................................................35
2. H323 Information...........................................................................................................37
IP Phone Ver. 113/503(Normal and PPPoE)
1
IP Phone 100 User Manual Guide Document Ver. 1.8
3. System Configure...........................................................................................................39
4. PPPoE Configure ...........................................................................................................40
Chapter 5 Upgrade the IP Phone 100..............................................................................................52
1.LCD Panel Control .........................................................................................................52
2.Remote Control: Telnet...................................................................................................53
3.Web Management ...........................................................................................................54
IP Phone Ver. 113/503(Normal and PPPoE)
2
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 1 Introduction
The IP Phone 100 is a full-featured IP-based telephone system, which provides VoIP service on LAN or any IP based environment. By using IP environment for voice communication, company or individual can save lots of expenses and make data and voice network converged.
IP Phone 100 also supports PSTN analog line connection. Therefore, it can perform as the same as traditional POTS (Plain Old Telephone Service).
IP Phone Ver. 113/503(Normal and PPPoE)
3
IP Phone 100 User Manual Guide Document Ver. 1.8
＊Product Description
1.Features and Specification
Basic Features:
ITU-T H.323 v3 compliance DTMF detection/generation TFTP/FTP software download Remote configuration/reset via Telnet LED indication for system status：Speaker, Hold ,Mute , Message , PSTN Network Interface :
- Switch Hub inside, providing 2 RJ-45 sockets for 10/100Base-T connection
- 1 RJ-11 socket for PSTN connection
Microsoft Net Meeting v3.0 compatible SNTP (Simple Network Time Protocol) Call HOLD/TRANSFER/FORWARD/MUTE PSTN/IP side access switch 10 Direct Line Button for speed dial Speaker Mode System Configuration from keypads and displayed on LCD Ring Tone selection Password setting for security Function Keys : Speaker , Redial , Mute , Hold , Transfer , Forward , Message , PSTN Ten sets last Phone Number redial Dial plan Provide TOS(Type Of Service) function GateKeeper mode or Peer to Peer mode selection
Caller ID:
IP side display H323-ID and E.164. Display the count of total call received. Display un-answered call name, number. Show caller’s name, number, calling time.
Volume Adjustment:
Speaker volume level adjustable. Handset Receiver volume level adjustable.
IP Phone Ver. 113/503(Normal and PPPoE)
4
IP Phone 100 User Manual Guide Document Ver. 1.8
LCD:
2 lines, 24 character Dot Matrix display. Indicator messages of HOLD, MUTE, PSTN, Directed Line 1~10. Display current date and time. Display of call duration.
Audio features:
 Codec -- G.711 a/μlaw, G.723.1 (6.3Kbps),G.729, G.729a  VAD (Voice Activity Detection), CNG (Comfort Noise Generate)  G.168/165-compliant adaptive echo cancellation  Dynamic Jitter Buffer  Bad Frame Interpolation  Provide H.245 Out-band DTMF message  Call Transfer (H.450.2)  Call Forward (H.450.3)  Call Hold (H.450.4)  Gain (Voice Volume) Settings  Provide Call Progress Tone: Dial tone, busy tone, call-holding tone and ring-back tone
Firmware Upgrade:
Firmware version displayed on LCD. Two ways to upgrade firmware:
- Download by KEYPAD configuration.
- Download by Telnet.
Management Features:
Two easy ways for system configuration
- TELNET
- IP Phone 100 KEYPAD (can only upgrade application rom file)
- Web Browser
- Management Center(only simple configuration)
IP Phone Ver. 113/503(Normal and PPPoE)
5
IP Phone 100 User Manual Guide Document Ver. 1.8
2.Appearance
1.Front View and Keypad function
♦ C: Cancel and Clear ♦  : Move to left /previous and right/next . ♦ OK: Press OK to confirm the modification. ♦ Direct Line (DL) Button 1 – 10: User press DL button to do speed dial according to phone
book data 1-10 (please refer to LCD configuration-Phone Address Book or Advanced Configurations via Telnet-[pbook] command ).
IP Phone Ver. 113/503(Normal and PPPoE)
6
IP Phone 100 User Manual Guide Document Ver. 1.8
♦ Number 1 –10, * and #: The function is as the same as the general phone set.
Corresponding list of keypad and symbol:
1 “Space” ; “,” ; “.” ; “!” ; “1” 2 “A” ; “ B” ; “C” ; “2” 3 “D” ; “E” ; “F” ; “3” 4 “G” ; “H” ; “I” ; “4” 5 “J” ; “K” ; “L” ; “5” 6 “M” ; “N” ; “O” ; “6” 7 “P” ; “Q” ; “R” ; “S” ; “7” 8 “T” ; “U” ; “V” ; “8” 9 “W” ; “X” ; “Y” ; “Z” ; “9” * “-“ ; “?” ; “*” 0 “0” # “_” ; “@” ; “#”
♦ MUTE: Mute the voice of MIC and let others can’t hear from user in communication. ♦ PSTN: Press PSTN to switch IP Phone 100 as PSTN or IP Phone Mode. In PSTN mode,
“PSTN” characters will be displayed on LCD left bottom side, then users can dial out as if standard telephone set in PSTN ; in IP Phone mode , “GK” characters will be displayed on LCD left bottom side.
Note:1. When IP Phone is in PSTN mode, only PSTN and SPEAKER function key can work.
2. On LCD will display ”….Incoming Call…. ” to notice user when IP Phone has both IP and PSTN side incoming calls.
3. If in communication with IP side, user can press HOLD to hold IP side, then press PSTN to pick up PSTN side, after that can press HOLD again to retrieve IP side.
4. If in communication with PSTN side, user must hang up PSTN side before pick up IP side by pressing PSTN.
♦ HOLD: To hold a call with H.450 function. ♦ SPEED: Press SPEED and number (Phone book index) to do speed dial according to phone
book data (please refer to LCD configuration-Phone Address Book or Advanced Configurations via Telnet-[pbook] command ).
♦ FORWARD: Forward a incoming call to another IP device by H.450 forward function.(please
refer to LCD configuration-Indicate Forward Type)
♦ MESSAGE and its indicated LED light: When missing the incoming calls, the message LED
will be flashing. User can know the information of miss call by pressing the message button.
♦ TRANSFER:
IP Phone Ver. 113/503(Normal and PPPoE)
7
IP Phone 100 User Manual Guide Document Ver. 1.8
1. Transfer a call by H.450 transfer function. Press TRANSFER button in communication and
press phone No. which user want to transferred to can transfer this call .
2. Change characters to be capital or lowercase: when press TRANSFER before press letters
can switch type of letters.
♦ REDIAL: Redial the last outgoing call. ♦ + and - : Adjust the voice volume in communication. ♦ SPEAKER: Speaking without picking up handset.
Note: All function keys mentioned above (except Number 1 –10, * and # ) are effective only in IP Phone mode.
2.Back V iew
♦ DC 9V: DC 9V power input outlet ♦ LAN: RJ-45 connector, connected directly to the Hub through the straight CAT-5 cable. ♦ PC: RJ-45 connector, connected directly to the PC through the straight CAT-5 cable ♦ Line: RJ-11 connector, connected directly to the PSTN analog line.
Note: There are two LED indicated lights: LINK/ACT and 10/100 for LAN port and PC port. When network status is in normal, LED of LINK/ACT will be flashing; when transmit rate is in 10 mbps/100mbps, LED of 10/100 will light off/on .
IP Phone Ver. 113/503(Normal and PPPoE)
8
IP Phone 100 User Manual Guide Document Ver. 1.8
3.Specification of connector
1、Ethernet Port：
Ethernet port is for connecting IP Phone to network, transmit rate supports 10/100 Base-T.
Ethernet connector（LAN）
2、RJ11connector：
RJ11 connector is for connecting IP Phone with PSTN.
RJ11connector
IP Phone Ver. 113/503(Normal and PPPoE)
9
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 2 Operating Procedure – LCD Display Configuration
1.Initialize IP Phone 100
1. When power on the IP Phone 100, the LCD screen shows as below.
2. Wait around one minute until the IP Phone 100 finishes boot program initialization.
3. User can see flashing greeting as below:
IP-Phone
Board Start Booting
System Initializing…………..
4. Then IP Phone get into standby mode:
GK 10:10:10 AM
IP-Phone
The main LCD screen would be shown as similar as above. The GK word means the IP Phone 100 is in GateKeeper Mode, and when IP Phone is connected to SNTP server, on LCD will show current time from SNTP server.
5. After pressing the PSTN button, the GK word will be replaced by PSTN. Then IP Phone is
in PSTN Mode. Please notice that in PSTN mode user must plug PSTN line in RJ-11 port.
PSTN 10:10:10 AM
IP-Phone
Press  or  to enter configuration mode then press OK Bottom to enter certain menu.
There are 6 selections for configuration.
1. System Configuration (mandatory, protected by password)
2. User Line Number (mandatory)
3. Ring Configuration
4. Indicate Forward Type
5. Message Box
6. Phone Address Book
Note: LCD Panel of IP Phone 100 is operated manually by moving  or on the keypad. Press
OK to enter separate configuration menu. Press C to go back to the main menu.
IP Phone Ver. 113/503(Normal and PPPoE)
10
IP Phone 100 User Manual Guide Document Ver. 1.8
2.LCD Configuration
User can set the following 10 configurations manually by operating the commands displayed on LCD.
Note: Any configurations that have made for the IP Phone 100, user has to do Reboot in the selection 1→5 “Reboot”.
1. System Configuration (mandatory, protected by password)
Please Enter Password:
User must key in password to enter this menu, selections under this command are all important ones, which can only be configured by administrators.
Note: Password to enter System Configuration:
H.323 token password (please refer to item 9), default value is x
1. Connect Configuration
There are ten sub-configurations included in Connect Configuration. It is necessary for user to set it in order to run the IP Phone 100 correctly.
In addition, user has to prepare one valid IP Address to meet your network environment. (Global public IP Address or Virtual IP Address)
(1) IP address
In this configuration mode, user presses the prepared IP Address on the IP Phone keypad. Please input IP address as format: xxx.xxx.xxx.xxx.
(2) Subnet Mask:
User has to press the subnet mask IP Address on the IP Phone keypad.
(3) Gateway
User has to press the default gateway IP which meets IP Address on the IP Phone keypad.
(4) Primary DNS
User can set IP address of Domain Name Server, then for GateKeeper and Phone book can enter URL address or IP address. Please refer to 3.9 [pbook] and 3.12
[h323] command.
(5) Secondary DNS
User can set IP address of secondary DNS, once primary DNS cannot work normally, IP Phone can refer to secondary DNS.
(6) GateKeeper
User has to offer one available GateKeeper server IP Address and set this IP Address on the IP Phone keypad.
(7) Second GateKeeper
IP Phone Ver. 113/503(Normal and PPPoE)
11
IP Phone 100 User Manual Guide Document Ver. 1.8
IP Phone provide alternative GateKeeper feature, if IP Phone can’t register to Main GateKeeper for 10 times, it will try to register to the Second GateKeeper. When main GateKeeper can’t work normally, IP Phone can still keep working with Second GateKeeper
(8) SNTP Configuration
IP Phone 100 supports that user can assign one SNTP (Simple Network Time Protocol) Server in your country by setting in IP Phone. User has to offer one available SNTP server IP Address and set this IP Address on the IP Phone keypad.
(A) SNTP Mode: User can set different time can set SNTP function too be
on/off/broadcast, which means IP Phone will capture current time from SNTP server or not, or broadcast to find a SNTP server and capture current time.
(B) SNTP Server: User can specify a SNTP server for IP Phone to capture
current time.
(C) Time Zone: User can set time zone according to the location IP Phone is.
For example, in Taiwan the time zone should be set as 8,which means GMT+8.(user can press “*” as “-“)
Note: If user didn’t set SNTP server, on LCD won’t display current time.
(9) Connection Mode
There are 2 types for IP Phone 100 to connect to the other devices. They are GK, P2P. The default mode is in GK mode. When user would like to connect via P2P
mode, the IP Phone 100 must change as well. Move the “~” symbol by press or on the keypad to select one mode.
(10) DHCP Mode (ON/Off)
User can set IP Phone in DHCP mode, which means IP Phone will get a dynamic IP automatically.
(11) Token Password
(A) LCD menu password: User can enter LCD system configuration by key in
this password
(B)H.235 security: To set RRQ/ARQ authentication token password. If IP
Phone wants to register to a GateKeeper, which implement H.235 security token feature, IP Phone has to set a RRQ/ARQ authentication token password, which is provided by GateKeeper manager. IP Phone can’t work normally with this GateKeeper unless Token Password is set.
IP Phone Ver. 113/503(Normal and PPPoE)
12
IP Phone 100 User Manual Guide Document Ver. 1.8
(12) Management Center
Set management center IP address. IF user specifies management center IP address, IP Phone will connect and send information to management center, let user can easily configure via management center interface.
Note: 1.management center is our optional software to help user can easily
configure our products, please contact your reseller to know more about it.
2.If user wants to disable Management Center function in LCD menu, use can key in IP address 255.255.255.255.
(13) GRQ Option
To set auto discovery function OFF or ON. If this function is enabled and IP address of GateKeeper is set as 255.255.255.255, IP Phone will multicast to search a GateKeeper on network with configured GateKeeper ID(please refer to (12)Gatekeeper ID); if IP address of GateKeeper is set, before IP Phone register to the assigned GateKeeper, it will send out GRQ(GateKeeper Request) message with configured GateKeeper name to GateKeeper first.
(14) GateKeeper ID
To set GateKeeper name for GateKeeper discovery. When IP Phone send out GateKeeper discovery message will search GateKeeper with this GateKeeper name
2. User Line Name
User has to identify one ID name for the IP Phone 100 to register to the GateKeeper.
3. Firmware Update (1) Download method
There are two methods to download new rom file, please move the “~” symbol by press or on the keypad to select TFTP or FTP method, then press OK to confirm it.
(2) Set File Server IP
User has to offer one TFTP/FTP server IP Address and set this IP Address on the IP Phone keypad. The IP Address is necessary for upgrading IP Phone new application rom file.
(3) Set FTP user account
User has to press user name and password for FTP server login .It is necessary for
upgrading IP Phone new application rom file in FTP method. (4) Indicate file name
IP Phone Ver. 113/503(Normal and PPPoE)
13
IP Phone 100 User Manual Guide Document Ver. 1.8
User has to press the file name of new application rom file prepared for upgrading
(5) Start Download
Press OK to start download new application rom file. After download is finished, IP Phone will automatically reboot.
(6) Firmware Version
Show versions of all rom files and hardware.
Note: Download via LCD command can only upgrade new application rom file.
4. Hardware Test
IP Phone 100 provides self-test for all functions buttons. Please follow the direction from LCD panel to operate and verify it.
5. Reboot
It is necessary and important for user to reboot it after any configurations has been made to the IP Phone 100.
2. User Line Number
User has to identify at least one number for the IP Phone 100 to register to the GateKeeper. User can set up to 10 different numbers.
(1) Line Number 1 (2) Line Number 2 (3) Line Number 3 (4) Line Number 4 (5) Line Number 5 (6) Line Number 6 (7) Line Number 7 (8) Line Number 8 (9) Line Number 9 (10) Line Number 10
Note: User can set six zero “000000” on LCD to disable this number and the number after this one. Ex. Line Number 1-5 are configured, if user set Line 3 as “000000”, Line number 3-5 will be disabled.
3. Ring Configuration (1) Ring Style Selection
There are three tone styles for IP Phone 100. Move the “~” symbol by press or on the keypad to select the tone style preferred, then press OK to confirm it.
IP Phone Ver. 113/503(Normal and PPPoE)
14
IP Phone 100 User Manual Guide Document Ver. 1.8
Choose T one Style:
Low Middle High
(2) Ring Volume Control
User can adjust ring volume by by press or on the keypad to decrease or increase volume.
4. Indicate Forward Type
There are two selections to activate or deactivate forward function. After selection please press OK
(1).Activate : choose under which situation to forward call to another endpoint. After
selection please press OK, then enter LINE NUMBER of another endpoint prepared to forward to.
1. Busy
When IP Phone 100 is in busy status, the incoming call will be directly forwarded to the assigned phone number.
2. No response
When IP Phone 100 is continuing ringing around 10 seconds, the incoming call will be directly forwarded to the assigned phone number.
3. Unconditional
It is included the above two types. Whether the IP Phone is in which status, it will be automatically forwarded to the assigned phone number.
(2).Deactivate : choose under which situation to deactivate forward function. After
selection, please press OK , then user can see LINE NUMBER of the endpoint which is already configured to forward to, now press OK again.
Note: The number that user prepares to forward to is E.164 number which is
registered on the GateKeeper.
5. Message Box
If there is an unanswered IP call, it will be kept in message box . MESSAGE LED will be flashing until user press MESSAGE to check miss call and re-press MESSAGE to return to main screen.
1. New Call：to see all incoming-call records in message box.
2. History：to see all records in message box.
IP Phone Ver. 113/503(Normal and PPPoE)
15
IP Phone 100 User Manual Guide Document Ver. 1.8
6. Phone Address Book
1. Display
Display all name and telephone number recorded to the phone address book.
2. Add
Add and save name, telephone number and IP address of the phone address book.
3. Edit
Edit name, telephone number, and IP address of Phone book.
4. Delete
Delete the record in the phone address book.
Note: When key in IP address in Pbook table, please do not add 0 before IP
address (ex.10.1.1.1 please do not key in 010.001.001.001).
IP Phone Ver. 113/503(Normal and PPPoE)
16
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 3 Advanced Configurations via Telnet
After initializing the IP Phone 100 IP Address setting (please refer to LCD Configuration:
1.Connect Configuration), user can enter into configuration mode via telnet. There are 18 commands listed below.
Note:
1.After user enter IP Phone configuration via telnet, please use login : ”root”, password : ”press enter” to enter command line.
2.Each command user must key-in with lower case, but contents of configurations such as h.323 alias or user name etc, user can set as capital case.
3.User who changes any configuration needs to do the commit command then reboot command.
1. [help] command
Type help or man or ? to display all the command lists. The following figure is shown all commands of IP Phone 100.
IP Phone Ver. 113/503(Normal and PPPoE)
17
IP Phone 100 User Manual Guide Document Ver. 1.8
2. [quit] command
Type quit/exit/close will logout IP Phone 100 and Telnet Program.
3. [reboot] command
After typing commit command, type reboot to restart the IP Phone 100. Sometimes after user type reboot, on terminal screen will display :"Data modified, commit to flash rom?", which means IP Phone will record call history or not.(ex. REDIAL , outgoing and incoming call data)
4. [flash] command
This command will clean the configuration stored in the flash rom to default value and reboot the IP Phone 100. Note: After user upgrade new software version, suggested to execute this command to make sure new software work well on IP Phone 100.
Note: To execute the command flash –clean, all configuration of IP Phone 100 stored on flash rom will be cleaned. It is authorized for the user whose login name is “root” only.
IP Phone Ver. 113/503(Normal and PPPoE)
18
IP Phone 100 User Manual Guide Document Ver. 1.8
5. [commit] command
Save any changes after configuring the IP Phone 100.
6. [ifaddr] command
Configure and display the IP Phone 100 IP information.
1. -ip, -mask, -gate: Set IP Phone 100 IP Address, subnet mask and default gateway
respectively.
2. -dhcp: When DHCP function enables (ifaddr –dhcp 1), IP Phone 100 will automatically
search DHCP server after execute the commit and reboot command.
Note: After IP Phone catch a dynamic IP address form DHCP server, user can see this IP
address on LCD connect configuration.
3. -sntp: When sntp server is available, enable IP Phone 100 SNTP function and point to sntp
server IP address. (ifaddr –sntp 1 “xxx.xxx.xxx.xxx”)
4. -dns:User can set Domain Name Server IP address. Once IP Phone can connect with DNS
server, user can specify URL address instead of IP address for gatekeeper and phone book IP address. (please refer to 12.[h323] command and 3.9[pbook] command)
5. –timezone: User can set different time zone according to the location IP Phone is. For
example, in Taiwan the time zone should be set as 8,which means GMT+8. (GMT-8: ifaddr –timezone -8)
6. -ipsharing: If IP Phone 100 is behind a IP-sharing , user can enable IP sharing function and
specify public IP address.(ifaddr –ipsharing 0/1 “public IP address of IP sharing” , 0 for disable and 1 for enable)
7. -cmcenter: Set management center IP address. IF user specifies management center IP
address, IP Phone will send information to mana gement center, let user can easily configure via management center interface. (ifaddr –cmcenter “IP address of management center” ;
ifaddr –cmcenter x to disable this function)
IP Phone Ver. 113/503(Normal and PPPoE)
19
IP Phone 100 User Manual Guide Document Ver. 1.8
Note: management center is optional software to help user can easily configure our products, please contact your reseller to know more about it.
7. [time] command
When sntp server is established as well as the sntp function of IP Phone 100 is enabled, type time command should show the current time what is retrieved from the assigned sntp server.
Note: Please refer to the Chapter 4.6 [ifaddr] command to configure sntp server..
8. [ping] command
Command ping can test which the IP address is reachable or not. Usage: ping “xxx.xxx.xxx.xxx(IP address)” The message will display packets transmitting condition or no answer from the IP address.
IP Phone Ver. 113/503(Normal and PPPoE)
20
IP Phone 100 User Manual Guide Document Ver. 1.8
9. [pbook] command
The command is for Peer-to-Peer Mode use only. Therefore, our VoIP products such as IP Phone 100 that support Peer-to-Peer Mode are also available to be addressed on the IP Phone 100 phone book.
1.-print: display phone book data. User can print all data in phone book by command
(pbook –print). Furthermore, user can also print only a section of data by indicate parameter 'start_record' and 'end_record' (pbook –print “start prefix” “end prefix”). If parameter 'end_record' is omitted, only record 'start_record' will be display (pbook –print “start prefix”).
2.-add: add a new record in phone book table by give a name and e164 number for the
Gateway / Terminal IP address .
(pbook –add name “X” ip “xxx.xxx.xxx.xxx” e164 “X”) User can set IP or URL address( Domain Name Server must be configured. Please refer to 6.
[ifaddr] command)
3. -search: search any record such as ip address, name and e164 addressed on the phone book.
4. -delete: delete a record with index listed in phone book table. (pbook –delete “index
number”)
5. -insert: insert an record in specified index of phone book.
6. -modify: modify any record that has addressed to index number. The name, IP address and
e164 number should be modified together in one modify command.
(pbook –modify “index” name “X” ip “xxx.xxx.xxx.xxx” e164 “X”)
Note: Please dial “#” after dial e.164 of pbook .
IP Phone Ver. 113/503(Normal and PPPoE)
21
IP Phone 100 User Manual Guide Document Ver. 1.8
10.[pppoe] command
Note: Firmware of IP Phone are separate into normal version and PPPoE version.
1. This command can only see in PPPoE version, in normal version PPPoE function is not implemented.
2. In PPPoE version has no TOS command.
1. -print: display system overall information and configuration. IF IP Phone has already connected to PPPoE server, user can see IP address and related information with this command.
2. -dev: to enable or disable PPPoE function.(pppoe –dev 0/1)
3. –open: to open PPPoE connection(If IP Phone is not in PPPoE connection, user can try to connect with pppoe -open)
4. –close: to close PPPoE connection(If IP Phone is in PPPoE connection, user can disconnect with pppoe -close)
5. –id: to set PPPoE connection user name
6. –pwd: to set PPPoE connection password
7. –reboot: If user enable this function, after PPPoE being disconnected, IP Phone will automatically reboot to re-connect, and after reboot, if IP Phone still can’t get contact with server, IP Phone will keep trying to connect. On the other hand, if user disable this function, IP Phone won’t reboot and keep trying to connect.(pppoe –reboot 0/1)
IP Phone Ver. 113/503(Normal and PPPoE)
22
IP Phone 100 User Manual Guide Document Ver. 1.8
11.[sysconf] command
This command displays the system information and configuration.
1. -print: display system overall information and configuration.
2. -plan: It is for setting dial numbering plan. While e164 number is three digits, the plan should be set as 3 or 0. The plan 0 is for any positive digits use.
3. –callalive: Enable or disable auto-disconnection after 10 seconds not receiving packets from remote party(sysconf –callalive 0/1, 0 for disable and 1 for enable)
4.-keypad:set DTMF type .User can select DTMF type IP Phone receive and transmit.(sysconf –keypad 0/1/2/3 , 0 for inband ,1 for H.245 alphanumeric, 2 for H.245 signal type, 3 for Q.931 user info, 4 for RFC2833.)
5.-idto:set the duration(in second) of two pressed digits in dial mode as timed out. If after the
duration user hasn’t pressed next number, IP Phone will dial out all number pressed.
6.-eod:select end of dialing key, e.g set end of dial key as OK button , after finished pressing dialing number then press OK will dial out. (sysconf –eod 0/1/2/3 , 0 for no end of dial key , 1 for “OK” button , 2 for “#” button , 3 for “＊” button )
7.-h450:Enable or disable H.450 related features, which include transfer, hold and forward.
IP Phone Ver. 113/503(Normal and PPPoE)
23
IP Phone 100 User Manual Guide Document Ver. 1.8
12. [h323] command
1. –print: display H.323 stack information and configuration.
2. –mode: configure IP Phone 100 as GateKeeper or Peer-to-Peer Mode.
Usage:h323 –mode 0/1(0 for GateKeeper mode ,1 for Peer-to-Peer mode)
3. –gk: set Main GateKeeper IP address(h323 –gk “xxx.xxx.xxx.xxx”) or URL
address( D omai n Na me Se rv er mu st be configured. Please refer to 6. [ifaddr] command) . User can set IP as 255.255.255.255 and let IP Phone auto discovery for GateKeeper. Please notice in this case, user must enable gatekeeper discovery function.Please refer to
5.-gkname and 10.-gkdis.
4. –dfgw:to set IP address of default gateway, this function is the same as Microsoft
NetMeeting.
A. To implement this feature both calling and called endpoints must be under
peer-to-peer mode.
B. If the called party is FXO products, such as TIG-404, which Have to set
sysconf –2nddial 0 to make one-stage dialing.
Dial remote PSTN number under default gateway, IP Phone will
automatically dial to default gateway, then default gateway will dial this number to PSTN side.
For example, user wants to dial to ext.888 under TIG-404, user only
have to dial 888 from IP Phone.
C. If called party is FXS products such as TIG-404S : user can dial line
number of TIG-404S from IP Phone.
For example ,user wants to dial to TIG-400，the configuration of 3502 is
h323 –line1 101 –line2 102，user can press 101 or 102 dialing to line1 or line2 of TIG-400.
5. –algk:set IP address or URL address( Domain Name Server must be configured. Please
refer to 6. [ifaddr] command) of alternative GateKeeper. If IP Phone tries to register to main GateKeeper for 10 times but still fail, IP Phone will try to register to alternative GateKeeper.
6. –gkname:set GateKeeper name for GateKeeper discovery. When IP Phone send out
GateKeeper discovery message will search GateKeeper with this GateKeeper name.(please refer to 10.-gkdis)
7. –e164: identify one number for the IP Phone 100 to register to the GateKeeper
(h323 –e164 “X”).
8. –e164-x:user can assign other 10 telephone numbers .For example, 10 users share the same
IP Phone, they can assign phone numbers as 100, 200, 300….(h323 –e164 100 –e164-1 200 –e164-2 300….) User can disable one number and the number after this one. Ex. from set 1-5 is configured, if user set the third number as “x”, from third to fifth number will be
IP Phone Ver. 113/503(Normal and PPPoE)
24
IP Phone 100 User Manual Guide Document Ver. 1.8
disabled at the mean time. (ex. h323 –e164-2 x)
9. –alias: identify ID for the IP Phone 100 to register to the GateKeeper (h323 –alias
“X”)..The default alias is related to MAC address of IP Phone, so each IP Phone has different alias.
10. –tokenpwd: To set RRQ/ARQ authentication token password.(h323 –tokenpwd
“password” ; h323 –tokenpwd x to disable this function)
(A) LCD menu password: User can enter LCD system configuration by key in this
password and default value is lowercase “x.” (press TRANSFER to switch lowercase and uppercase).
(B) H.235 security: To set RRQ/ARQ authentication token password. If IP Phone wants
to register to a GateKeeper, which implement H.235 security token feature, IP Phone has to set a RRQ/ARQ authentication token password, which is provided by GateKeeper manager. IP Phone can’t work normally with this GateKeeper unless Token Password is set.
11. –gkdis: set auto discovery function on or off. If this function is enabled and IP address of
GateKeeper is set as 255.255.255.255, IP Phone will multicast to search a GateKeeper on network with configured GateKeeper name(please refer to 6.-gkname); if IP address of GateKeeper is set, before IP Phone register to the assigned GateKeeper, it will send out GRQ(GateKeeper Request) message with configured GateKeeper name to GateKeeper first.
12. –rtp: assign RTP port number(1024-65535)
13. –ttl:set RAS TTL time(0-3600 second)
14. –gkfind: assign GateKeeper finding port number(1024-65535)
15. –ras: assign GateKeeper RAS port(1024-65535)
16. –range: assign dynamically allocated port range(1500-65535)
17. –respto: set max waiting time for first response to a new call. After dial phone No. without
getting response in max waiting time, user will hear busy tone.(1-200 seconds)
18. –connto: set max waiting time for call establishment after receiving first response of a new
call (1-20000 seconds).
Note: 1.Items from 9-16 are for advanced user only.
2.In Peer-to-Peer mode, h323 –print will only display e164, alias, mode ,
RTP port, and allocated port range.
3.In P2P mode, please dial “#” after press IP address (ex.10.1.1.1 please dial 10*1*1*1#) or e.164 of Phone book (Please refer to chapter 3.9 Pbook command).
IP Phone Ver. 113/503(Normal and PPPoE)
25
IP Phone 100 User Manual Guide Document Ver. 1.8
13. [voice] command
The voice command is associated with the voice codec setting information.
1.-print: display voice codec information and configuration.
There are five voice codecs included in IP Phone 100:G.723.1, G.711u, G.711A, G.729a,
G.729.
2. -send: three voice packet size can be configured as 20 ms, 40 ms or 60 ms.(only 30 and 60
ms for G..723)
3. -priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need, for example, voice –priority g723 or voice –priority g723 711a g711u g729a g729 means IP Phone can support only one codec or five codecs.
4. -volume: There are three types can be adjustable, voice volume, input gain and DTMF volume.
5. -nscng: enable or disable sound compression and comfort noise generation. It is only for codec G.723.1. (0 for off ,1 for on)
6. -echo: echo canceller can be made to each specified port. The default value is on to 6 ports.
7.-mindelay:set minimum delay of jitter buffer(0~150)
8.-maxdealy:set maximum delay of jitter buffer(0~150)
IP Phone Ver. 113/503(Normal and PPPoE)
26
IP Phone 100 User Manual Guide Document Ver. 1.8
Note: It is for advanced administrator use only. Please ask your distributor before changing any settings of this command.
14. [tos] command
This command is for setting IP packet TOS values to determine IP Packets priority on network.
1. -print : display current TOS values configurations.
2. -rtptype : configure TOS type of RTP packets from 0 to 7
3. -rtcptype : configure TOS type of RTCP packets from 0 to 7
4. -rtpdelay : configure RTP packets as normal delay or low delay
5. -rtcpdelay : configure RTCP packets as normal delay or low delay
6. -rtpthruput : configure RTP packets as normal throughput or high throughput
7. -rtcpthruput : configure RTCP packets as normal throughput or high throughput
8. -rtpreliab : configure RTP packets as normal reliability or high reliability
9. -rtcpreliab : configure RTCP packets as normal reliability or high reliability
Note: This command won’t be functional until network environment can be capable with TOS function.
IP Phone Ver. 113/503(Normal and PPPoE)
27
IP Phone 100 User Manual Guide Document Ver. 1.8
15. [tone] command
IP Phone 100 is configurable of busy tone, reorder tone, ring tone and dial tone. However, only ring tone and dial tone is functional for now, busy tone and reorder tone are reserved for future feature.
Usage：tone –ringtone1/ringtione2/dialtone “low frequency” “high frequency” “low frequency level” “high frequency level” “low frequency on time” “low frequency off time” “high on time” “high frequency off time”; user must key in 8 sets of number to finish
this configuration. If it is single-frequency tone, please set high frequency and related items as
0. Furthermore, unit of on/off time is 1/100 second, and suggest to keep level as default value
(8).User can also increase the value of level to increase the volume.
IP Phone Ver. 113/503(Normal and PPPoE)
28
IP Phone 100 User Manual Guide Document Ver. 1.8
16. [support] command
1.-print : display current SUPPORT values configurations.
2.-fstart: enable or disable fast start (support –fstart 0/1 , 0 for disable and 1 for enable.)
Note: When fast start function is enabled, if user wants to send DTMF message after connection, IP Phone will send out Q.931 message. (Please refer to 11.sysconf –keypad command, which can only set keypad as q.931 message at this time)
3.-tunnel: enable or disable H.245 tunnel function.(support –tunnel 0/1 , 0 for disable and 1
for enable)
4.-h245fs:set if open H.245 separate channel after fast start or not. (support –h245fs 0/1 , 0
for open and 1 for not.)
17. [bureau] command
Type bureau can display commands below.
1. -print: display bureau line information and configuration.
2. -hold: set hold tone generation on or off. If other terminals support H.450 hold function, and
execute hold function when connecting with IP Phone 100, user will hear hold tone from IP Phone 100. (0 for off ,1 for on)
IP Phone Ver. 113/503(Normal and PPPoE)
29
IP Phone 100 User Manual Guide Document Ver. 1.8
18.[rom] command
1. -print: show versions of all rom files.
2. -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and -htpcm: upgrade main boot code, main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone .
3. -boot2m:to upgrade 2mb rom file, which includes all firmware file mentioned in item 2.
Note:
1. After 2mb file download is finished, all configurations might change to default value,
user has to configure again.
2. MAC address might change to default value also, please MUST use command setmac:
Usage: key in command setmac key in MAC address (which you can see on a label attached at the bottom of
IP Phone )with format:
00 01 a8 00 0x xx (It means to press enter each time after key in two characters.)
4. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading firmware rom file.
5. -f: the file name prepared for upgrading is necessary as well.
6. –server: specify TFTP/FTP server IP address. It is corresponding to LCD configuration
-firmware upgrade-Set file Server IP.
7. –method: specify download method to be TFTP or FTP(0 for TFTP.1 for FTP)
8. –ftp: specify user name and password for FTP download method For example: User prepares to upgrade the latest app rom file – wtlp.103c, the TFTP server is
192.168.4.101.
rom –app –s 192.168.1.1 –f lp.100(If –server is specified , can just type rom –app –f lp.100)
IP Phone Ver. 113/503(Normal and PPPoE)
30
IP Phone 100 User Manual Guide Document Ver. 1.8
Command rom –print can show current version installed in IP Phone 100.
IP Phone Ver. 113/503(Normal and PPPoE)
31
IP Phone 100 User Manual Guide Document Ver. 1.8
19.[passwd] command
For security protection, user has to input the password before entering application user/config mode. Two configurations of login name/password are supported by the system.
1. –set: set password of “root” users or “administrator” users. (password –set root/administrator “password”)
2.–clean: clean up password restored before, and user can login :”root/adminstrator”, password:”press enter”.
User who requests authorization to execute all configuration commands needs to login with “root”. If a user login with “administrator”, two commands are not functional:
1. password –set root: set password of login : “root”.
2. passwd –clean: clean up password restored before, and user can login :”root/adminstrator”,
password: ”press enter”.
3. flash –clean: only “root” users can clean all configurations stored in flash.
4. rom –boot :only “root” users can upgrade IP Phone boot rom version.
5. rom –boot2m : only “root” users can upgrade IP Phone 2mb firmware.
IP Phone Ver. 113/503(Normal and PPPoE)
32
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 4 Web Configuration
The initial version for HTTPD web management interface provides user to configure easily rather than command operating method through RS-232 / TELNET.
The configuration function and step is similar with the way through command line. Basically this version is not the finalized version for web interface. Initially please refer to the manual for more information. Below provide a simple user guide for user to configure via web interface. Next version for HTTPD web management will not like the command format, but friendly interface.
Step 1. Browse the IP Address predefined via RS-232
IP Phone Ver. 113/503(Normal and PPPoE)
33
IP Phone 100 User Manual Guide Document Ver. 1.8
Step 2. Input the login name and password
Login name: root / administrator Password: None (just press Enter in default value)
Step 3. The web interface main screen
IP Phone Ver. 113/503(Normal and PPPoE)
34
IP Phone 100 User Manual Guide Document Ver. 1.8
Step 4. Start configure
Most of all commands displayed in console / telnet are transfer to web interface. The most important commands are Network Interface, H323 Information, Commit Data and Reboot System. The method is as the same as command mode.
1.Network Interface
Please refer to chapter 3.6 [ifaddr] command.
- DHCP: Enable / Disable to DHCP mode
- IP Address: Set IP Address
- Subnet Mask: Set the Subnet Mask
- Default gateway: Set Default routing gateway
- Domain Name Server: Set Domain Name Server IP address
- SNTP: Enable / Disable the Simple Network Time Protocol
- SNTP Server Address: Set SNTP Server Address
- GMT: Set time zone for SNTP Server time
- IP Sharing: Enable it if behind IP Sharing router
- IP Sharing Server Address: Set WAN IP Address of IP Sharing Server router if it is a fixed one.
- Management Center IP Address: Set Management Center Address
Please be noted: If the WAN IP Address of IP Sharing Server router is not a fixed one, it is not necessary to input any values. If behind the dynamic WAN IP Address situation please configure as GK mode and select TGK-103 Call Manager as proxy server.
IP Phone Ver. 113/503(Normal and PPPoE)
35
IP Phone 100 User Manual Guide Document Ver. 1.8
IP Phone Ver. 113/503(Normal and PPPoE)
36
IP Phone 100 User Manual Guide Document Ver. 1.8
2. H323 Information
Please refer to chapter 3.12 [h323] command
- Mode: Select GK mode or Peer-to-Peer mode
- Gatekeeper IP Address: Set Gatekeeper IP Address
nd
- 2
- Gatekeeper Id: Set GateKeeper ID
- Gatekeeper Discovery: Enable/Disable GRQ function
- Registered E.164 Number-01: Set 1st phone number
- Registered E.164 Number-02: Set 2nd phone number
- Registered E.164 Number-03: Set 3rd phone number
- Registered E.164 Number-04: Set 4th phone number
- Registered E.164 Number-05: Set 5th phone number
- Registered E.164 Number-06: Set 6th phone number
- Registered E.164 Number-07: Set 7
Gatekeeper IP: Set Redundancy Gatekeeper IP Address
th
phone number
- Registered E.164 Number-08: Set 8th phone number
- Registered E.164 Number-09: Set 9th phone number
- Registered E.164 Number-10: Set 10th phone number
- Registered H.323 ID: Set Registered Alias as H323 ID
- Token Password: Set Token password for H.235 security use
- RTP Port Time to Live (TTL) Gatekeeper finding port RAS Port
Response Timeout Connection Timeout: For Advanced User only
IP Phone Ver. 113/503(Normal and PPPoE)
37
IP Phone 100 User Manual Guide Document Ver. 1.8
-
IP Phone Ver. 113/503(Normal and PPPoE)
38
IP Phone 100 User Manual Guide Document Ver. 1.8
3. System Configure
Please refer to chapter 3.11 [sysconf] command
- Keypad Type: Select different DTMF Keypad Type (For Advanced User)
- Dial Plan: Set DTMF digit limitation (0 is for any digits)
- Call Alive: Enable the function to check connection (Both side must support)
- Inter Digit Time: Set the DTMF inter digit time (second)
- Digit Type of End of Dialing: Select end of dialing type as none, OK, #, or * .
- H.450 Related Features: Enable/Disable H.450 function.
IP Phone Ver. 113/503(Normal and PPPoE)
39
IP Phone 100 User Manual Guide Document Ver. 1.8
4. PPPoE Configure
Please refer to chapter 3.10 [pppoe] command
- Device: Enable/Disable PPPoE function
- User Name: Set PPPoE Connection User Name
- Password: Set PPPoE Connection password
- Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection
- Other items: After PPPoE connection established, related information will be displayed
IP Phone Ver. 113/503(Normal and PPPoE)
40
IP Phone 100 User Manual Guide Document Ver. 1.8
5. Voice Setting (For Advanced User)
Please refer to chapter 3.13 [voice] command
- Codec Priority: It got wrong order with “Frame Size”. Select the packet size in sending process. (For Advanced User)
- Sending Packet Size: Select the Codec Priority. (For Advanced User)
- G.723 Silence Suppression: Enable / Disable (For Advanced User)
- Volume : Adjust the volume in “Voice” (sending out); “Input” (receiving); “ DTMF” (DTMF sending out) Please Noted the value is limited.
- Echo Cancel: Enable / Disable (suggested always Enable)
- Jitter Buffer: Min. Delay and Max. Delay (For Advanced User)
IP Phone Ver. 113/503(Normal and PPPoE)
41
IP Phone 100 User Manual Guide Document Ver. 1.8
6. Tone Setting (For Advanced User)
Please refer to chapter 3.15 [tone] command
- Busy Tone:
- Reorder Tone:
- Ring Tone 1
- Ring Tone 2
- Dial Tone:. Set the above tone Frequency , Level and On/Off time
IP Phone Ver. 113/503(Normal and PPPoE)
42
IP Phone 100 User Manual Guide Document Ver. 1.8
7. Bureau Setting
Please refer to chapter 3.17 [bureau] command
- Hold Tone Generation(using PCM file): Enable/Disable hold tone generation
IP Phone Ver. 113/503(Normal and PPPoE)
43
IP Phone 100 User Manual Guide Document Ver. 1.8
8. Support Functions (Both side must support)
Please refer to chapter 3.16 [support] command
- Fast Start: Enable to do Fast Start
- H.245 Tunneling: Enable to open H.245 Tunneling
- H.245 Separate Channel: Enable/Disable open H.245 channel after fast start connection
IP Phone Ver. 113/503(Normal and PPPoE)
44
IP Phone 100 User Manual Guide Document Ver. 1.8
9. Phone Book (For Peer-to-Peer mode only)
Please refer to chapter 3.9 [phone] command
Input the Name, IP Address and E.164 No. of the destination device. Please Note: The E.164 No. will not be carried together to the destination side. It is said if the destination side is requested to match its E.164 No. (Line No.), user can input any digit he wished.
IP Phone Ver. 113/503(Normal and PPPoE)
45
IP Phone 100 User Manual Guide Document Ver. 1.8
10. Password
Please refer to chapter 3.19 [password] command
First select login name as root or administrator, then enter current password , new password and confirm new password again.
IP Phone Ver. 113/503(Normal and PPPoE)
46
IP Phone 100 User Manual Guide Document Ver. 1.8
11. ROM Upgrade
Please refer to chapter 3.18 [rom] command
- TFTP Server IP Address: Set TFTP server IP address
- Target File name: Set file name prepared to upgrade
- Method: Select download method as TFTP or FTP
- FTP Server IP Address: Set FTP server IP address
- FTP Login: Set FTP login name and password
- Target File Type: Select which sector of IP Phone to upgrade
IP Phone Ver. 113/503(Normal and PPPoE)
47
IP Phone 100 User Manual Guide Document Ver. 1.8
12. Flash Clean
Please refer to chapter 3.4 [flash] command
Press CLEAN will clean all configurations of IP Phone and reset to factory default value.
Please be noted: Once execute this function, user must re-configure all commands all over again.
IP Phone Ver. 113/503(Normal and PPPoE)
48
IP Phone 100 User Manual Guide Document Ver. 1.8
13. Commit Data
Please refer to chapter 3.5 [commit] command
After configuration, user has to commit data then reboot machine.
IP Phone Ver. 113/503(Normal and PPPoE)
49
IP Phone 100 User Manual Guide Document Ver. 1.8
14. Reboot System
Please refer to chapter 3.3 [reboot] command
IP Phone Ver. 113/503(Normal and PPPoE)
50
IP Phone 100 User Manual Guide Document Ver. 1.8
15. Version Information
Please refer to chapter 3.18 [rom] command
User can see all S/W versions.
Note: If there is item can’t be found on web site, please configure them by telnet.
IP Phone Ver. 113/503(Normal and PPPoE)
51
IP Phone 100 User Manual Guide Document Ver. 1.8
Chapter 5 Upgrade the IP Phone 100
IP Phone 100 supports two methods to upgrade the new version released from TTIC. Both methods are necessary to prepare the TFTP program on the host PC as TFTP server. After installing TFTP program on one PC and connecting to network, IP Phone 100 is ready to be upgraded.
1. LCD Panel Control
2. Remote Control: Telnet
3. Web Management
＊Download Procedure
1.LCD Panel Control
1.Choose the 1→3 selection-Firmware Upgrade. Press OK to enter into the
sub-selection as below.
2.Download method
There are two methods to download new rom file, please move the “~” symbol by press or on the keypad to select TFTP or FTP method, then press OK to confirm it.
3.Set File Server IP
User has to offer one TFTP/FTP server IP Address and set this IP Address on the IP Phone keypad. The IP address is necessary for upgrading IP Phone new application rom file.
4.Set FTP user account User has to press user name and password for FTP server login .It is necessary for
upgrading IP Phone new application rom file in FTP method.
5.Indicate file name User has to press the file name of new application rom file prepared for upgrading
6.Start Download
Press OK to start download new application rom file .
7.Firmware Version Show versions of all rom files.
Note: Download via LCD command can only upgrade new application rom file.
IP Phone Ver. 113/503(Normal and PPPoE)
52
IP Phone 100 User Manual Guide Document Ver. 1.8
2.Remote Control: Telnet
Associated with the Chapter 3.18 [rom] command:
1. -print: show versions of all rom files.
2. -app,-boot, -dsptest, -dspcore, -dspapp, -rbpcm and -htpcm: upgrade main boot code,
main application code, DSP testing code, DSP kernel code, DSP application code, Ring Back Tone PCM file and Hold Tone .
3. -s: it is necessary to prepare TFTP/FTP server IP address for upgrading rom file.
4. -f: the file name prepared for upgrading is necessary as well.
9. –server: specify TFTP/FTP server IP address. It is corresponding to LCD configuration
-firmware upgrade-Set file Server IP.
10. –method: specify download method to be TFTP or FTP(0 for TFTP.1 for FTP)
11. –ftp: specify user name and password for FTP download method
For example: User prepares to upgrade the latest app rom file – wtlp.103c, the TFTP server is
192.168.4.101.
rom –app –s 192.168.1.1 –f lp.100 (If –server is specified , can just type rom –app –f lp.100)
IP Phone Ver. 113/503(Normal and PPPoE)
53
IP Phone 100 User Manual Guide Document Ver. 1.8
3.Web Management
Please refer to chapter 3.18 [rom] command
- TFTP Server IP Address: Set TFTP server IP address
- Target File name: Set file name prepared to upgrade
- Method: Select download method as TFTP or FTP
- FTP Server IP Address: Set FTP server IP address
- FTP Login: Set FTP login name and password
- Target File Type: Select which sector of IP Phone to upgrade
IP Phone Ver. 113/503(Normal and PPPoE)
54
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use