Target 9-Cube, 58020, 58023 Assembly Instructions Manual

>> assembly instructions

9-Cube

style dpci nish

58020 002-11-0590 White
58023 002-11-0588 Espresso

2

Congratulations on your latest Target purchase.

Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room
in no time. Good luck—though we’re condent you won’t need it.

tools needed

before you begin

1. Check for damaged or missing parts. Call 1-800-874-0008 to order missing supplies.

2. Use the carton as a working surface to prevent product damage during assembly.

3. Gather all tools prior to assembly.

3

introduction 2

hardware 4

parts list 5

safety precautions 6

helpful hints 7

installing L-bracket 8

assembly 9-18

table of contents

QUESTIONS? Just call 1-800-874-0008 for parts and service. For faster service, have the style number and DPCI number ready when calling.

4

hardware

(H5) x 10
short dowel

(H1) x 20

assembly screw

#10 x 1-1/2 in. athead

(H2) x 20
screw cover

(H9) x 1
L-bracket

(H7) x 1
L-bracket screw
#10 x 1/2 in. athead

(H8) x 1

wall screw

#10 x 1-1/2 in.

(H3) x 2
hole plug

(H6) x 60

nail

(H4) x 8

long dowel

5

A

A

B

B

C

C

D

D

D

D

D

D

E

E

ITEM DESCRIPTION QUANTITY

A side panel 2
B top/bottom panel 2
C horizontal divider 2

D vertical divider 6
E back panel 5

6

• This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or
serious injury could occur.

• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse.
Serious bodily injury and/or damage to personal belongings may occur.

• Do not overload unit. If any shelf, top, or bottom of unit bows or bends greater than 1/2 in., it is overloaded. The shelf, top, or bottom could
collapse and cause serious bodily injury and/or damage to personal belongings.

• Do not climb or step on the unit. This is not a bench. The unit may become unstable and either tip or collapse. Serious bodily injury and/or
damage to personal belongings may occur.

• Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings may occur.

• Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily
injury and/or damage to personal belongings may occur.

• Do not stack units in a vertical format. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury and/or
damage to personal belongings.

• Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings,
and/or damage to the wall may occur.

• All units must be secured individually to wall stud using L-Bracket and Wall Screw (#10 x 1-1/2 in.) provided. If wall stud is not accessible,
consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to
serious bodily injury and/or damage to personal belongings.

• We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood oors, etc.

safety precautions

warning

7

We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood oors, etc.

helpful hints

Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all
the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same
way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will
face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.

hand tighten screws

We recommend you hand-tighten screws. Use care not to overtighten if using power tools.

unfinished edgefinished edge

8

There are several "key points" to
L-bracket installation. Please review the
drawings and comments at right as well
as the assembly steps provided.

All units must be fastened to the wall.
Always mount L-bracket to a wall-stud.

installing L-bracket

short

end

long
end

wall
stud

Install short end against wall/wall
stud; long end against unit.

Do not install this unit ush against the
wall! This unit requires a gap of between
1/2 inch and 1 inch to install properly.

For more hidden hardware, secure L-bracket
under top panel. See step 10 for detailed
installation instructions.

Max.
1 in.

Min.
1/2 in.

wall
stud

top panel

wall
stud

Serious or fatal crushing injuries can occur
from furniture tip-over.

To help prevent tip-over:

- Install tip-over restraint provided.

- Unless specically designed to
accommodate, do not set TVs or other
heavy objects on top of this product.

- Never allow children to climb or hang on
drawers, doors, or shelves.

- Place heavy items on lower shelves and as
far back as possible.

Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.

This is a permanent label. Do not attempt to remove.

WARNING

9

1. Push 4 short dowels into holes of one xed shelf.

2. Install dowels only into one top/bottom panel (both top/bottom panels are the same.)

3. Top/Bottom panels have six holes on one side with the middle holes going through to the other side.

4. Unnished edges are shaded in light gray.

B

step 1.

(H5) x 4
short dowel

10

1. Attach xed shelf to one side panel.

2. Make sure nished edges of unit are up.

A

B

step 2.

(H1) x 2

assembly screw

#10 x 1-1/2 in. athead

11

1. Attach one set of vertical dividers.

2. Push vertical dividers onto dowels in xed shelf.

3. Make sure nished edges of unit are up.

4. From opposite side of xed shelf, secure each vertical divider with a screw.

D

D

step 3.

(H1) x 2

assembly screw

#10 x 1-1/2 in. athead

12

1. Insert long dowels.

2. Attach horizontal divider. Be sure to assemble with all nished edges to front.

3. Push horizontal divider down over dowels. (Holes in horizontal dividers go all the way through.)

4. Secure horizontal divider with two screws through side panel.

C

step 4.

(H1) x 2

assembly screw

#10 x 1-1/2 in. athead

(H4) x 4

long dowel

13

1. Attach one set of vertical dividers.

2. Insert long dowels.

3. Attach horizontal divider. Be sure to assemble with all nished edges to front.

4. Push horizontal divider down over dowels. (Holes in horizontal dividers go all the way through.)

5. Secure horizontal divider with two screws through side panel.

6. Attach second set of vertical dividers.

C

D

D

D

D

step 5.

(H1) x 2

assembly screw

#10 x 1-1/2 in. athead

(H4) x 4

long dowel

14

1. Insert SHORT dowels and attach top xed shelf. Be sure to assemble with all nished edges to front.

2. Align holes in underside of top xed shelf and place top panel into position.

3. Secure top panel with two screws through side panel.

4. Secure top vertical dividers with two screws through top panel.

step 6.

(H1) x 4

assembly screw

#10 x 1-1/2 in. athead

(H5) x 4
short dowel

15

1. Attach other side panel with provided screws.

2. Be sure to assemble with all nished edges to front.

step 7.

(H1) x 8

assembly screw

#10 x 1-1/2 in. athead

16

1. Lay unit so nished (front) edges face down and unnished edges face up. (Unnished surfaces are shaded in gray.)

2. Push screw covers onto all screw heads. Gently tap in place with hammer.

3. Position the back panels in a staggered pattern as shown.

4. Nail the back panels into place through the holes provided, being careful not to angle the nail.

E

step 8.

(H2) x 20
screw cover

(H6) x 60

nail

17

1. Install dowels or hole plugs.

2. For single unit: Insert hole plugs into top holes.

3. For stacking units: Insert dowels into top holes.

step 9.

(H5) x 2
short dowel

(H3) x 2
hole plug

when
stacking units

single unit

18

1. Align center of unit with wall stud. (All units MUST be fastened to the wall. When stacking units, the unit on the bottom must be attached to the
wall rst before setting another unit on top. Do not stack units more than 72 in. high.)

2. Place short end of L-bracket against wall/wall stud. Use 1-1/2 in. screw to secure L-bracket to wall.

3. Use 1/2 in. screw to secure L-bracket to top panel. Mount L-bracket through an open cube which does not have a back panel.

when
stacking units

single unit

step 10.

(H9) x 1
L-bracket

(H7) x 1
L-bracket screw
#10 x 1/2 in. athead

(H8) x 1

wall screw

#10 x 1-1/2 in.

wall
stud

top panel

top panel

wall
stud

19

weight capacity/care instructions

15 lbs.

15 lbs.

15 lbs.

40 lbs.

15 lbs.

15 lbs.

15 lbs.

15 lbs.

15 lbs.

15 lbs.

This unit has been designed for the weight
shown. Exceeding this recommended weight
could result in excessive "sagging" of the top
or shelves. Extreme overloading can cause
failure of the unit and possible injury.

Care Instructions:

Dust with a clean, lint-free dry cloth.

warning

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.