Instruction Manual
DVD +RW/-RW Player / Recorder
DR-5100x
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
1
Important Instructions
1 Read these instructions.
2 Keep these instructions.
3 Heed all warning.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the grounding-type
plug. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10 Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
17 This appliance shall not be exposed to dripping or splashing
water and that no object filled with liquid such as vases shall
be placed on the apparatus.
18 Power Lines - An outdoor antenna should be located
away from power lines.
19 Outdoor Antenna Grounding - If an outside antenna is
connected to the product, be sure that the antenna
system is grounded so as to provide some protection
against voltage surges and built up static charges.
GROUND
GROUND CLAMPS
ELECTRICS ERVICE
ELECTRICSERVICE
EQUIPMENT
EQUIPMENT
GROUND CLAMPS
GROUND CLAMPS
CLAMPS
GROUND
GROUND
CLAMPS
CLAMPS
POWER SERVICE
POWER SERVICE GROUNDING
GROUNDING
ELECTORDE SY STEM
ELECTORDE
(NEC ART.250,PART H)
SYSTEM
ANTENNA LEAD IN
ANTENNA
WIDE
LEAD IN
WIDE
ANTENNA
ANTENNA
DISCHARGE
DISCHARGE UNIT
UNIT
(NEC SECTION 810-
20)
GROUNDING
GROUNDING CONDUC-
CONDUCTORS
TORS
(NEC SECTION 810-20)
20 The wall outlet must be easily accessible.
21 To completely disconnect the device from the electrical
power, unplug the power cord.
22 Do not use any extension cords.
14 Refer all serving to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
15 Battery usage CAUTION - To prevent battery leakage
which may result in bodily injury, property damage, or
damage to the unit:
• Install all batteries correctly, + and - as marked on the
unit.
• Do not mix batteries (old and new or carbon and alkaline,
etc.).
• Remove batteries when the unit is not used for a long
time.
16 To reduce the risk of fire or electric shock, Do not
expose this apparatus to rain or moisture
2
IMPORTANT INSTRUCTIONS
CAUTION
“VENTILATION SHOULD NOT BE IMPEDED BY COVERING THE
VENTILATION OPENINGS WITH ITEMS, SUCH AS NEWSPAPER, TABLECLOTHS, CURTAINS, ETC”.
“NO NAKED FLAME SOURCES, SUCH AS LIGHTED CANDLES, SHOULD
BE PLACED ON THE APPARATUS.”
“THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THEAPPARATUS.”
“THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND SHALL
BE REMAIN READILY OPERABLE”.
Warning: To reduce the risk of electric shock, do not
remove the cover or back of this product. There are no
userserviceable parts inside. Refer servicing to qualified
service personnel.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show, broadcast via
cable, play in public, or rent copyrighted material without
permission. This product features the copy protection function
developed by Macrovision. Copy protection signals are
recorded on some discs. When recording and playing the
pictures of these discs picture noise will appear. This product
incorporates copyright protection technology that is protected
by method claims of certain U.S. patents and other intellectual
property rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT.
SERIAL NUMBER:
Warning: This digital video disc recorder
employs a laser system. Use of controls,
adjustments, or the performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
Warning: To prevent direct exposure to laser
beam, do not open the enclosure. Visible laser
radiation when open.
Warning: Never stare directly into the laser beam.
Caution: Do not install this product in a confined
space such as a book case or similar unit.
This product is manufactured to comply with the
radio interference requirements of EEC
DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/
EEC.
You can find the serial number on the back of the unit. This number
is unique to this unit and not available to others. You should record
requested information here and retain this guide as a permanent
record of your purchase.
Model No. DR-5100x
Serial No. C124
Date of Purchase
3
Table of Contents
Important safety instructions ...............................2
General information ............................................4~5
Features ................................................................. 4
DVD region code .................................................... 4
Disc can be playbacked ......................................... 4
Disc can be recorded ............................................4
Glossary of disc terms ..........................................4
Supplied Accessories ............................................ 4
Inserting batteries into the remote control ............. 4
Notes on disc .........................................................5
Conventions about this manual .............................. 5
Function Overview ...............................................6~7
Front panel ............................................................. 6
Back panel .............................................................. 6
Remote control ....................................................... 7
Basic Connection .................................................8~10
Connect your DVD recorder to TV set .................. 8
Connect your DVD recorder to Audio devices .....9
Before initial setting .............................................12~13
Setting the clock ..................................................... 12
Setting the channel ................................................. 12
Watch TV .......................................................... 12
Nicam Select ...................................................... 12
Auto CH Scan .....................................................12
Channel List ........................................................13
Modify Channel ................................................... 13
Initial settings ....................................................... 14~20
DVD control .............................................................14~16
Setting Disc Menu .............................................14
Setting Angle Mark ............................................. 14
Setting Audio ...................................................... 14
Setting Subtitle ................................................... 14
Setting Parental Control ......................................15~16
General ................................................................... 17
Setting Menu Language ..................................... 17
Setting Screen Saver ....................................... 17
Setting Factory Defaults ............................. ..... 17
Video .......................................................................17
Setting TV Display ............................................ 17
Setting TV Type .................................................18
Setting Video Output .........................................18
Setting Rear AV IN Select ................................ 18
Setting Front AV IN Select ............................... 18
Speaker ...................................................................19
Setting Down Mix .............................................. 19
Setting Center, Rear, Subwoofer ......................... 19
Setting Center Delay ........................................... 19
Setting Rear Delay ............................................. 18
Speaker Test ...................................................... 18
Audio .......................................................................20
Setting Digital Out .............................................. 20
Setting Dynamic Compress ................................ 20
Pro Logic ............................................................ 20
Recording ............................................................. 21~26
Preparations ............................................................ 21
Recording setup ...................................................... 21~22
Setting Recording Qaulity .................................21
Setting Auto Chapter ........................................22
Recording TV Programs ......................................... 22
Timer Recording ..................................................... 23~26
Set the record program(s) first ...........................23
Setting Record Time ..................................... 23
Setting Frequency ........................................23
Setting VPS ................................................ 23
Setting Input Source ..................................... 24
Setting Channel ............................................24
Setting Quality ............................................. 24
Setting Title ..................................................24
Recording List .................................................... 25
Show View .......................................................... 25
Press STANDBY/ON to turn the power off ..........26
Recording from an External Equipment ................. 26
One Touch Recording ............................................ 26
Playback Features ................................................26~31
Preparations ........................................................... 26
Start or Pause Playback ........................................26
Stopping Playback ................................................. 26
Fast Playback ........................................................ 26
Skip Playback ........................................................ 27
Slow Motion Playback ........................................... 27
Step Playback ........................................................ 27
Repeat Playback .................................................... 27
A-B Repeat Playback ............................................. 27
Using DVD TITLE menu .........................................27
Using MENU/PBC ..................................................27
Return ...................................................................27
GOTO ................................................................... 27
Display the playback information ........................... 28
Subtitle ................................................................. 28
AUDIO................................................................... 28
Language ..............................................................28
Zooming ................................................................28
Angle .................................................................... 29
Intro play mode .....................................................29
Shuffle playback .................................................... 29
Programmed playback ...........................................29
Sleep timer setting ............................................... 29
Activating/Deactivating Progressive Scan mode ..... 29
MP3 CD Playback ...............................................29
MPEG4 Playback ................................................ 30
KODAK Picture CD Playback ............................... 30
JPEG CD Playback ............................................. 30
KODAK Picture CD / JPEG Picture Playback ......30
DivX Playback ......................................................... 31
Managing the disc contents ................................32~34
Playing/Edit titles ................................................... 32
PLAY TITLE .......................................................32
TITLE DELETE ................................................... 32
TITLE RENAME .................................................32
Edit titles ................................................................ 33
Erase Disc ........................................................ 33
Finalize Disc .......................................................33
Rename Disc ..................................................... 33
Protect Disc ........................................................ 34
Troubleshooting Guide ........................................ 35
Maintenance ..........................................................37
Specifications ....................................................... 37
4
General Information
Features
Built-in Dolby Digital decoder, supporting Dolby Pro Logic and Virtual
Surround
5.1Channel audio out
Progressive Scan
DV-IN
TV tuner receiver
Conforming DVD+/-R, DVD+/-RW, SVCD,VCD1.1,VCD2.0,MP3,
MPEG4,CDR,CDRW discs
DVD navigation and SVCD,VCD2.0 PBC controlling functions
VFD front panel display and OSD menu display
Full function remote control
Standby By pass
DVD region code
DVD players and discs are designed with region numbers which dictate
the region (printed on the rear panel). If the region number does not
match the region number in your DVD player, you will not be able to
play the disc. If you try to play the DVD, the message “ WRONG REGION
NUMBER” will appear on OSD.
The region number for this DVD player is 2
Disc can be played back
DVDs
Disc are general recorded with multi-titles.
Titles may be subdivided into chapters.
Track (Video or audio CD)
Sections of a picture or a music piece on a VIDEO or a CD. Each
track is assigned a track number enabling you to locate the track
you want.
Supplied Accessories
Check that you have the following items:
RF antenna cable
RCA cable(RCA x 1 pair)
Remote control
AA batteries
Owner’s manual
Scart Cable
Test DVD Burosch
Inserting Batteries into the Remote Control
You can control the system using the supplied remote. Insert two
batteries by matching the + and - on the batteries. When using the
remote, point it at the remote sensor on the front panel of this system.
Video CD (version 2.0, 1.1,) / SVCD
Disc are general divided into tracks.
Audio CDs / MP3 / Kodak picture CD
Disc are divided into tracks.
Note
You cannot play CD-G, CD-EXTRA, , CD-ROM and DVD-ROM discs.
You cannot play illegally produced discs.
You cannot play scratched discs.
You cannot play disc that are dusty, soiled or marked with
fingerprints.
DISC can be recorded
DVD +/-R (Digital Versatile Disc +/- recordable)
DVD +/-RW (Digital Versatile Disc +/- rewriteable)
Glossary of disc terms
Title (DVD)
The longest sections of a picture or a music piece on a DVD; a
movie, etc., for a picture piece on a video software; or an album,
etc., for a music piece on and audio software. Each title is assigned
a title number enabling you to locate the title you want.
Chapter (DVD)
Sections of a picture or a music piece that are smaller than titles.
A title is composed of several chapters. Each chapter is assigned
a chapter number enabling you to locate the chapter you want.
Depending on the disc, no chapters may be recorded.
Note
Do not leave the remote in an extremely hot or humid place.
Do not use a new battery with an old one.
Do not drop any foreign object into the remote casing. particularly
when replacing the batteries.
Do not expose the remote sensor to direct sunlight or lighting
apparatuses. Doing so many cause a malfunction.
If you will not use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery leakage
and corrosion.
Attention! Dispose worn-out batteries not with your domestic waste.
Please contact your local government for disposal practices in
your area.
5
Notes on disc
Disc handling precautions
To keep the disc clean, handle the disc by its edge. Do not touch
the surface.
Do not stick paper or tape on the disc.
If there is glue (or a similar substance) on the disc, remove the glue
completely before using the disc.
Do not expose the disc to direct sunlight or sources such as hot
air ducts, or leave it in a car parked in direct sunlight as there can
be considerable rise in temperature inside the car.
After playing, store the disc in its case.
Do not write on the label side with a ball-point pen or other writing
utensils.
Be careful not to drop or bend the disc.
Disc cleaning precautions
Before playing, clean the disc with a cleaning cloth. Wipe the disc
from the center to out.
Conventions about this manual
• Instructions in this manual describe the controls on the system.
You can also use the controls on the remote control if they have
the same or similar names as those on the system.
• The types of functions and operations that can be used for a
particular disc vary depending on the features of that disc. In
some cases, these functions and operations may differ from the
descriptions given in this Operations Manual. In this event, follow
the instructions given on the screen. This Operations Manual only
covers basic disc operations.
• For some operations, the icon may appear on the screen. This
indicates that the operation described in this Operations Manual is
not permitted for the current disc.
• The drawings about the TV screen and front panel display used in
this Operations Manual are purely for the purposes of explanation.
The actual displays may differ slightly from what are shown here.
Do not use solvents such as benzine, thinner, commercially available
cleaners or anti-static spray intended for viny1 LPs.
Disc installing precautions
Do not install more than 1 disc on disc tray.
Do not place the disc on the tray up-side down.
Do not try to close the disc tray when the disc is not installed
properly.
6
FUNCTION OVERVIEW
Front panel
1237910846511
1- POWER
To power the unit on or off.
This DVD recorder consumes power in stand-by mode. In order to
avoid any power consumption use the power switch on the back
side.
2- OPEN/CLOSE
Press to open/close disc tray.
3- RECORD
Press to record.
4- CHANNEL (-)
Press to select previous TV channel
5- CHANNEL (+)
Press to select next TV channel
6- REC MODE
Select the record mode
7- DV IN
Connect the audio/video(game console camcorder. etc)
16
8- S-VIDEO IN
S-video input jack
9- VIDEO IN (AV2 IN)
Video input jack
10- AUDIO IN (L)
Audio input jack(left channel)
11- AUDIO IN (R)
Audio input jack(right channel)
12- PREV
Press to select the previous track or chapter.
13- NEXT
Press to select the next track or chapter.
14- STOP
Press to stop playback except for timer recording.
15- PLAY/PAUSE
Press to play or pause the playback
16- VFD
VFD will display the unit present work condition.
12 13 14 15
Back panel
8 9 10 11 12
1- ANTENNA
Connect RT ANTENNA to TV set
2- S-VIDEO (IN)
S-video input jack
3- AUDIO IN (Left and Right)
Audio input jacks
4- EURO AV IN (TO TV)
Euro AV input jack
5- S-VIDEO (OUT)
S-video output jack
6- OPTICAL OUT
Optical digital audio output
7- SUBWOOFER
Connect the Amplifier Sub terminals
213 574
13
6
8- COMPONENT VIDEO OUT
Component video output jacks
9- VIDEO IN
Video input jack
10- VIDEO OUT
Video output jack
11- COAXIAL OUT
Coaxial digital audio output
12- AUDIO OUT
Connect the Amplifier Audio input
13- EURO AV IN (TO VCR/DSR)
Euro AV input jack
14- POWER (ON/OFF)
Power switch
14
7
Remote control
OPEN/CLOSE: open or close the disc tray.
ANGLE: access various camera angles on DVD.
MUTE : press to shut off the sound or to restore the sound.
STANDBY/ON : switches the unit from between standby and on.
REPEAT : allow you to repeat a title, a chapter, a song or all songs on
the disc (usually used on music discs).
1)
A-B : repeat a certain segment between A and B.
INTRO : press to scan all the tracks with 10 seconds for each track(CD,
VCD only).
SHUFFLE : press to play the tracks at random.
SETUP : enter into the SETUP menu.
TITLE : displays the title menu if available (DVD only)
MENU/PBC : press to select the subtitle(root) menu.
SUBTITLE : access various subtitle language in DVD.
LANGUAGE :select a different Audio language or director narration.
Directional arrow buttons : select the item you want.
ENTER : press to enter a command or confirm a selection.
PROG : program the tracks in your own order (only VCD and CD)
AUDIO : changes the audio channels of a VCD or CD if available , or selects
stereo, left or right audio channel of a VCD disc.
SLOW : select the forward/backward slow speed playback.
PLAY/PAUSE : press to start or pause playback.
STOP : stops by momentarily or fully.
PREV SKIP: skip to previous chapter or track.
NEXT SKIP : skip to next chapter or track.
FAST BACKWARD: press to do fast backward search.
FAST FORWARD : press to do fast forward search.
ZOOM : press to enlarge the picture.
STEP : press to view playback frame by frame
RETURN : return back to the menu (VCD only).
GOTO: go to the desired starting title, chapter, track or time.
NUMBER KEYS : used in DVD menu and CD track selection.
DISPLAY : press to show the playing information about the disc.
CLEAR : press to clear what you select or input.
EDIT : press to edit what you record.
SOURCE : press to select your desired source.
N/P : press to switches between the PAL and NTSC system.
RECORD : press to start record.
REC MODE :press to select the record mode before recording.
TV : press to transfer to TV programmes.
SLEEP : To set the timer on the unit.
CHANNEL -/+ : press to select lower/upper TV program channel.
1) To power the unit on or off. This DVD recorder consumes power in stand-by mode. In order to avoid any power consumption use the power switch on
the back side.
8
BASIC CONNECTION
IMPORTANT !
Before connecting the AC power to the wall outlet,
ensure
that all other connections have been made.
Never make or change any connections with the power
switched on.
Connect your DVD recorder to TV set
If your TV set have the COMPONENT VIDEO OUT
socket, connect your TV with Component video cables
.
(Configuration C+D+E)
1. Insert ANTENNA cable into ANTENNA socket at the back of the
DVD recorder.
2. Insert one end of the supplied aerial cable to the ANTENNA OUT at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
3. Plug one end of the Video cable into the Green /Blue/ Red Component
Video output socket at the back of the DVD recorder and the other
end into the Video in or AV in socket on the TV set .
4. Insert one end of the supplied Audio cable into the Red/White socket
OUT L AUDIO R at the back of the DVD recorder and the other end
into the Audio input (usually red/white )socket on the TV set.
5. If your TV supports progressive scan, switch the recorder in OSD
to progressive scan. Attention: If the TV doesn’t support
progressive scan maybe the picture is dark or with a double picture.
In this case switch the recorder off and again on.
If your TV set have the SCART socket , connect your TV
with a Scart cable .(Configuration F)
1. Insert ANTENNA cable into ANTENNA socket at the back of the
DVD recorder.
2. Insert one end of the supplied aerial cable to the TV socket at the
back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
3. Plug scart cable into the corresponding scart socket at the back of
the TV set and the scart socket (SCART OUT)
4. If your TV supports RGB switch the recorder in OSD to Scart.
If your TV set have the S-Video socket , connect your TV
with a S-Video cable .(Configuration B+D+E)
1. Insert ANTENNA cable into ANTENNA socket at the back of the
DVD recorder.
2. Insert one end of the supplied aerial cable to the ANTENNA OUT at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
3. Plug one end of a S-Video cable into the S-Video 1 output socket
at the back of the DVD recorder and the other end into the SVideo input socket on the TV set .
4. Insert one end of the supplied Audio cable into the Red/White
socket OUT L AUDIO R at the back of the DVD recorder and the
other end into the Audio input (usually red/white )socket on the TV
set.
5. Switch the recorder in OSD to S-Video
If your TV set have the VIDEO OUT socket , connect your
TV with a Video cable . (Configuration A+D+E )
1. Insert ANTENNA cable into ANTENNA socket at the back of the
DVD recorder.
2. Insert one end of the supplied aerial cable to the ANTENNA OUT at
the back of the DVD recorder and the other end into the aerial input
socket at the back of the TV set.
3. Plug one end of the supplied Video cable into the yellow Video
(CVBS) output socket at the back of the DVD recorder and the
other end into the Video in or AV in socket on the TV set .
4. Insert one end of the supplied Audio cable into the Red/White socket
OUT L AUDIO R at the back of the DVD recorder and the other end
into the Audio input (usually red/white) socket on the TV set.
5. If your TV supports progressive scan, switch the recorder in OSD to
progressive scan. Attention: If the TV doesn't support progressive
scan maybe the picture is dark or with a double picture. In this case
switch the recorder off and again on.
Rear panel of TV set
(example only)
C
E
TV SET
F
B
A
D
9
Connect your DVD recorder to additional devices,
using second Scart socket
(Configuration A )
Connect your DVD recorder to additional devices,
using Video socket
(Configuration B/C )
You can connect additional devises such as decoders, DVD player,
etc. to the Scart In, then you can see the picture from the additional
device on your TV set. At same time, you can recorder the program
from the additional device.
Connect your DVD recorder to additional devices,
using second Scart socket
T Analogue audio sockets AUDIO OUT are located at the back of the
DVD recorder.
These can be used connect the following:
1) a receiver with Dolby Surround Prologic
2) a receiver with two - channel analogue stereo
Picture 1
DVD PLAYER
(Configuration D )
AMPLIFIER
You can connect additional devises such as decoders, camcorders, etc.
to the S-video /Video and Audio in ,then you can see the picture from the
additional device on your TV set. At same time, you can recorder the
program from the additional device. In this case you have the best quality
with S-Video. If you have a device with SCART connector use for better
quality the SCART-in conector(Configuratin A)
Connect your DVD recorder the digital audio socket
to Audio devices
At the back of the DVD recorder there are digital output socket Digital
DVD recorder.
For Dolby Digital and DTS sound through your Digital receiver you have
to use one of this connectors.
These can be used connect the following:
1) an A/V receiver or A/V amplifier with digital multi-channel sound decoder (e.g. 5.1/7.1 Dolby Digital/DTS receiver)
2) a receiver with two channel digital stereo
(Configuration E)
10
Front Left
(Not supplied)
Surround Left
(Not supplied)
AMPLIFIER
Front Right (Not
supplied)
Surround Right
(Not supplied)
SCART OUT
Passive subwoofer
(Not supplied)
DVD PLAYER, VCR, SAT/Cable/
Terrestrial Digital receiver etc.
Connect your DVD recorder to VCR or a similar
recording equipment
You can use this unit as the source player or as the recording deck. If
your VCR or similar equipment have a SCART connector use this
connetion. (See Picture 1 on the previous page)
Connection for recording from other equipment
You can connect additional devises such as decoders, camcorders,
etc. to the S-video /Video/component and Audio in , then you can see
the picture from the additional device on your TV set. At the same time
, you can record the program from the additional device .
1. Connect to the AV IN by a video cable.(configuration A+D)
2. Connect to the AV IN by a s-video cable.(configuration B+D)
3. Connect with component video cable.(configuration C+D)
Picture 2:
4. Connect to a camcorder etc. by a video/s-video/DV IN.
To copy camcorder recordings, you can use the front sockets
.These sockets are located behind the flap on the left hand side .
Best picture Quality (Configuration A)
If you have a DV or digital 8 camcorder , connect the DV IN of
the DVD recorder to the appropriate DV output on the
Camcorder.
Very good picture Quality (Configuration B+D)
If you have H18 or S-VHS (c) camcorder , connect the SVideo 2 of the DVD recorder to the S-VHS output on the
camcorder. you must also connect the audio input L AUDIO R
on the DVD recorder to Audio output on the camcorder.
Good picture Quality (Configuration C+D)
If your camcorder only have a single Video output (composite
Video , CVBS) , connect the Video(AV 2) of the DVD recorder
to the Video output on the camcorder. you must also connect
the audio input L AUDIO R on the DVD recorder to Audio
output on the camcorder.
C
A
BD
A
B
CD
11
BEFORE INITIAL SETTING
The SETUP Menu is carried out via the TV, it enable you to customize
the DVD recorder to suit your paticular requirment. If the preferred
opttions selected are not available on a disc, then the discs own
preference wil be used.
Turn on the TV and select the appropriate video input to suit the
connections to this unit. (Refer to your TV’s owner manual.)
Connect your DVD recorder to the TV as shown on page 9.
Press before setting if the unit is receiving the TV program.
1. Switch power bottom on the back side to on and press SETUP in
no disc mode or full stop mode.
2. Use
/ / / to select item you want.
3. Press ENTER on remote control to confirm the selection.
4. To exit setup menu, press SETUP again.
Menu
Play/Edit Disc
Record Program
Setup Menu
Tuner Setup
Press SETUP to exit Current selection
Press SETUP to exit
4:3 PS
Play/Edit Titles
v
4:3 LB
Edit Disc
16:9 Wide
Setting the clock
1. Press SETUP in no disc mode or full stop mode, “Menu” screen
appears on the TV screen.
2. Press
to select “Setup Menu”, then press ENTER or ,
“Recording Setup” is highlighted.
3. Press ENTER or
4. Press
to select “Set Clock ”, then press ENTER or , “Set Clock
again, “Recording Setup ”screen appears.
Setup ”screen appears.
5. Press
/ / / repeatedly (or number buttons) to set the date
and time.
6. Press
to select “Done” or “Cancel ”, and then press ENTER ,
“Recording Setup ”returns.
7. To exit, press SETUP.
8. Press Standby/on to turn off the unit , the clock appears on the FL
display.
Set Clock Setup
Select a field then use to edit.
Hour Minute Year Month Day
11 2004 / Jan / 01
Press SETUP to exit Current selection
Press SETUP to exit
4:3 PS
4:3 LB
16:9 Wide
Done Cancel
Setting the channel
1. Press SETUP in no disc mode or full stop mode, “Menu” screen
appears on the TV screen.
2. Press
to select “Tuner Setup ”, then press ENTER or , “Watch
TV ” is highlighted.
3. Press
/ to select the item.
Watch TV
1. Select “Watch TV ”.
2. Press ENTER to enter TV mode, TV screen appears.
3. To return to DVD mode, press
/ in remote control directly..
Nicam Select
1. Select “Tuner Selection ”.
2. Press ENTER or
3. Press ENTER or
select “AUTO ”or “OFF ”.
4. Press ENTER,"V" appears.
5. Press
repeatedly to return to “Menu” screen.
, “Tuner Selection ”screen appears.
to select the sub menu, then press / to
Tuner Selection
Nicam Select
Press SETUP to exit Current selection
Press SETUP to exit
4:3 PS
AUTO
v
4:3 LB
OFF
16:9 Wide
Current selection
v
Auto CH Scan
1. Select “Auto CH Scan ”.
2. Press ENTER or
, a message screen appears.
Menu
Play/Edit Disc
Record Program
Setup Menu
Press Yes to continue Auto Scan
Tuner Setup
press No to exit
Yes No
Press SETUP to exit Current selection
Press SETUP to exit
4:3 PS
4:3 LB
Watch TV
16:9 Wide
Tuner Selection
NICAMAuto CH Scan
Channel List
Modify Channel
12
Loading...