Targa DPV-5200 Series User's Manual And Service Information

Download

Page 1

Targa DPV-5200x

TARGA GmbH Lange Wende 41 D-59494 Soest www.targa-online.com

Ready for you:

www.targa.de

User's guide and service information

Front panel connections

1. Disc Tray

Insert a disc here.

2. 1/I

Switches the unit to ON or OFF.

3. PROG. (V/v)

Channel Programme Selectors

4. DVD

Opens or closes the disc tray.

5. Display window

Shows the current status of the unit.

DVD: DVD deck is selected.

A disc is loaded in the DVD deck.

[P]: Indicates the Progressive Scan is set to On

mode.

Indicates repeat mode.

DVD+VCR is in timer recording or a timer recording is programmed.

A Cassette is in the VCR deck.

VCR: VCR deck is selected. REC:

TV: Indicates TV mode.

6. Remote Sensor

Point the remote control here.

Tape Compartment

8. VCR

Tape Eject

..//mm

Go to beginning of current chapter/track or to PREVIOUS chapter/track. Press and hold for two seconds for a fast reverse search. Rewinds the tape.

10.

Starts playback.

MM//>>

11.

Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search. Winds the tape forwards.

12.

Stops playback.

13. DVD/VCR

DVD/VCR Selector

14. Video IN Jack

15.

Audio IN (L/R) Jacks

VCR recording is engaged.

DVD to VHS copy is in progress.

(See Notes on page 22.)

Indicates total playing time/elapsed time/current time.

Rear Panel

1. AERIAL

Connect the aerial using this jack.

2. RF.OUT

Connect to your TV using this jack.

3. VIDEO/AUDIO OUT(Left/Right) (DVD/VCR OUT)

Connect to a TV with video and audio inputs.

4. COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr) (DVD EXCLUSIVE OUT)

Connect to a TV with Y Pb Pr inputs.

COAXIAL (Digital audio out jack)

Connect to digital (coaxial) audio equipment.

6. AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT)

Connect to an amplifier, receiver or stereo system.

7. EURO AV2 DECODER

AV2/Decoder connector to connect an external device or to connect a decoder to watch encrypted broadcasting channels.

EURO AV1 AUDIO/VIDEO (VCR IN+OUT / DVD OUT)

Connect to your TV set or another video recorder.

9. AC Power Cord

Connect to a power source.

(DVD EXCLUSIVE OUT)

Page 2

Remote control - Overview

Important warranty information

Dear Customer,

Thank you for purchasing a TARGA product.

Please carefully read through the enclosed documentation or online help before putting your Targa product into service. If you have a problem, which can’t be solved in this way, please contact our hotline.

If the problem cannot be solved over the phone, you will be given a reference number (RMA), which you should enclose together with a copy of the proof of purchase. After you have packaged the unit safe for transport and in plain packaging, please send it for warranty processing, with the RMA noted on the outside of the package, to the address given to you by our hotline employee. After receiving the unit we will correct the manufacturing and material defect free of charge.

Up-to-date information and answers to the most frequently asked questions are available on the internet from:

www.targa-online.com

This guarantee is valid in the Ireland.

Your statutory guarantees from the seller are in addition to this warranty and are not limited by it.

Hotline number:

01-2421583

(Please have your

serial number to hand!)

36 month warranty from date of purchase

www.targa-online.com

Manufacturer: TARGA GmbH, Postfach 2244,

D-59482 Soest

Ireland 1191515

POWER

Switch this unit ON or OFF.

OPEN/CLOSE

EJECT

Open or close the disc tray.

Tape Eject.

TV/VCR

Switch between your TV’s tuner and the VCR’s

internal tuner.

DVD/VCR selection switch

Selects operation mode of

the remote control.

Switches modes of the device.

Select input source for

recording into tape.

PAUSE/STEP ( )

Pause playback temporarily / press repeatedly

for frame-by-frame

playback.

SKIP (. / >)

Go to next chapter or track.

Returns to beginning of current

VCR: Rewinds the tape during the STOP mode,

for fast reverse picture search and Advances

the tape during the STOP mode, fast forward

chapter or track or go to previous

chapter or track.

STOP ( ÁÁ)

Stops playback.

BACKWARD / FORWARD (m/ M)

DVD: Search backward or forward.

picture search.

PLAY (G)

Starts playback.

MARKER

Mark any point during playback.

Display MARKER SEARCH menu.

TITLE

Display the title menu of the

disc if available.

REC/ITR (OO)

Record your input sources into tape.

REPEAT

Repeat chapter, track, title, all.

RANDOM/CM SKIP

Play tracks in random order.

CM SKIP

DISPLAY CLK/CNT

Access the On-Screen Display. Shows you the current time or counter.

b / B / v / V(left/right/up/down)

Select an item in the menu.

PR/TRK (v / V)

Select channel programme of VCR. To adjust tracking. To control vertical tremble during picture still.

DISC MENU

Access menu of a DVD disc.

ENTER/OK

Acknowledge menu selection.

SETUP/ i

Access or remove setup menu.

RETURN

Displays the menu of a video CD with PBC.

0-9 numerical buttons

Select numbered items in a menu.

PROGRAM

Access or remove program menu.

CLEAR

Clear a track number on the program menu or a mark on the MARKER SEARCH menu. Reset tape counter to zero.

AUDIO

Select an audio language (DVD).

SUBTITLE

Select a subtitle language.

ANGLE

Select DVD camera angle if available.

ZOOM

Enlarge video image.

A-B/LP

Repeat sequence. Select the recording speed of the tape.

VIDEO Plus+

To display the programme menu for VIDEO Plus+ programming.

Page 3

Important Instructions

1 The following instructions should be read before the

product is operated.

2 This instruction manual should be retained for future

reference. 3 Heed all warnings. 4 All operating and use instructions should be followed. 5 Do not use this product near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions. 8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat. 9 Only use the supplied power cord to connect the device

to an appropriate wall outlet. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the product. 11 Only use attachments/accessories specified by the

manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with apparatus.

When a cart is used, use caution when moving the

cart/product combination to avoid injury from tip-over. 13 During lightning storms or when unused for long periods

of time, unplug this product from the wall outlet and

disconnect the antenna cable. 14 Refer all servicing to qualified service personnel.

Servicing is required when the product has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the product, the product has been exposed to

rain or moisture, does not operate normally, or has been

dropped. 15 Safety notes on battery usage - To prevent battery

leakage which may result in bodily injury, property

damage, or damage to the unit:

• Install all batteries correctly,+ and - as marked on the

unit.

• Do not mix batteries (old and new or carbon and alkaline,

etc.).

• Remove batteries when the unit is not used for a long

time.

Attention!

Do not try to recharge, disassemble, heat or dispose of

battery in fire. Disposal of old batteries is clearly

regulated by law.Dealers and community waste

authorities are obligated to recycle old batteries of

household quantities. Discharged batteries must not be

disposed of with your domestic waste. Use the

possibility of returning old batteries free of charge!

Protect the environment.Recycle used batteries. 16 To avoid electrical shock or fire do not expose the device

to rain or moisture. 17 The apparatus should not be exposed to water (dripping

or splashing). Do not place any objects on the apparatus

filled with liquids, such as vases. 18 Do not place any fire source such as candlelight on this

product.

19 Do not use any extension cords. 20 The wall outlet must be easily accessible. 21 The switch on the device does not completely

disconnect the device from the power source.The device still consumes power in stand-by mode. To completely disconnect the device from power unplug the power plug from the wall outlet. Be sure to install the device in a place where you can easily reach the AC outlet so that you can immediately disconnect the power plug in case of an emergency.To avoid danger of fire when the device is not used for a long period of time, such as on vacation, always disconnect the power plug from the outlet. Always grab the plug of the power cord. Never pull on the power cord and never touch the cord with wet hands. Otherwise there is danger of a shortcut or electrical shock. Do not put any heavy objects such as furniture, etc. on the power cord and be careful not to pinch the cord. Do not knot the power cord , and do not interconnect with other cables. Always place the power cord so that nobody will step on it. A damaged power cable can result in fire or electrical shock. Check the power cord regularly. If it is damaged, please contact the nearest authorized customer service center or your dealer for replacement.

22 Grounding and external antenna - When connecting an

external antenna to the device, the antenna system must be properly grounded to protect it from over currents and static discharge.

23 Do not use the product near strong magnetic fields (such

as speakers).

24 Children: Children should not operate electric devices.

Young children should be supervised when operating this appliance. Children cannot always see possible risks.Tear apart and throw away plastic packaging. There is a risk of suffocation.

25 If you operate this device in a country other than

Germany you must adhere to the laws and regulations of the respective country,in which the product is used.

26 Batteries and small parts can be swallowed easily. In this

case there is a risk of death. Keep batteries out of reach of children. If a battery was swallowed, immediately request medical assistance.

27 This appliance is classified as a “CLASS 1 LASER

product”.The label is located on the exterior. Never open the enclosure or try to repair the device yourself. Invisible laser radiation when open. Do not expose to laser beam.

Proper use:

This DVD-VCR recorder is a consumer electronics product. It is intended for private, non-industrial and non-commercial use only.This product must not be operated outside or in tropical regions. Only use connecting cables and external devices which meet safety related issues, electromagnetic conformity, and shielding requirements for this device.This device complies with all standards related to CE conformity. If you modify the device without the manufacturer's authorization these standards may not be assured. Only use accessories specified by the manufacturer.

Page 4

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION: Do not block any ventilation openings.Install in accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface.This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.

CAUTION:

This Digital Video Disc Player employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference, should the unit require maintenance, contact an authorized service locationsee service procedure. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure.Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.

CAUTION: The apparatus shall not be exposed to water, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC.

PERSONNEL.

SERIAL NUMBER: The serial number is found on the back of this unit.This number is unique to this unit and not available to others.You should record requested information here and retain this guide as a permanent record of your purchase.

Model No.___________________________________ Serial No. ___________________________________

Disposal of your old appliance

1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

CAUTION concerning the Power Cord Most appliances recommend they be placed upon a

dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets.Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized services.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon.Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord plug.When installing the product, ensure that the plug is easily accessible.

Introduction

Page 5

Table of Contents

Introduction

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

About the Symbol Display . . . . . . . . . . . . . . 5

Symbol used in this Manual . . . . . . . . . . . . . . . 5

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . 5

Handling Discs . . . . . . . . . . . . . . . . . . . . . . . . . 5

Storing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . . . . 5

Selecting the Viewing Source . . . . . . . . . . . . . . 5

Types of Playable Discs. . . . . . . . . . . . . . . . . . . 6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Preparation

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Connecting to a TV & Decoder(or Satellite) . . . . 10

Connecting to Optional Equipment . . . . . . . . . . . 11

Before Operation-VCR part . . . . . . . . . . . . . . . 12-16

Tuning in a video channel on your TV . . . . . . . . . 12

Using your VCR for the very first time . . . . . . . . . 12

Setting the clock Manually . . . . . . . . . . . . . . . . . 13

To set the colour system . . . . . . . . . . . . . . . . . . 13

How to use the main menu. . . . . . . . . . . . . . . . . 14

Tuning in TV Stations Automatically . . . . . . . . . . 14

Tuning in TV Stations Manually. . . . . . . . . . . . . . 15

Changing the order of TV Stations . . . . . . . . . . . 16

Deleting TV Stations . . . . . . . . . . . . . . . . . . . . . 16

Before Operation-DVD part . . . . . . . . . . . . . . . 17-20

Displaying Disc Information on-screen . . . . . . . . 17

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 17

General Operation . . . . . . . . . . . . . . . . . . . . . . . 17

LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

 Menu Language. . . . . . . . . . . . . . . . . . . . . . 18

 Disc Audio / Subtitle / Menu . . . . . . . . . . . . . 18

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

 TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . 18

 Display Mode. . . . . . . . . . . . . . . . . . . . . . . . 18

 Progressive Scan. . . . . . . . . . . . . . . . . . . . . 18

 TV Output Select . . . . . . . . . . . . . . . . . . . . . 18

AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

 Dolby Digital / DTS / MPEG. . . . . . . . . . . . . 19

 Sample Freq.(Frequency) . . . . . . . . . . . . . . 19

 DRC (Dynamic Range Control) . . . . . . . . . . 19

 Vocal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

LOCK (Parental Control) . . . . . . . . . . . . . . . . . . 19

 Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

 Password (Security Code) . . . . . . . . . . . . . . 19

 Area Code. . . . . . . . . . . . . . . . . . . . . . . . . . 20

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

 PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

 Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . 20

 DivX(R) VOD. . . . . . . . . . . . . . . . . . . . . . . . 20

Operation

Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-24

Playing a tape . . . . . . . . . . . . . . . . . . . . . . . . . . 21

 CM (Commercial Message) Skip . . . . . . . . . 21

 OPR (Optimum Picture Response). . . . . . . . 21

Instant Timer Recording. . . . . . . . . . . . . . . . . . . 22

VIDEO Plus+ Programming . . . . . . . . . . . . . . . . 23

Timer recording using On Screen Display . . . 24-25

Additional Operation - VCR part . . . . . . . . . . . . 26 - 28

Hi-Fi Stereo Sound System . . . . . . . . . . . . . . . . 26

On Screen Display (F.OSD) . . . . . . . . . . . . . . . . 26

Tape Counter Memory Stop . . . . . . . . . . . . . . . . 26

To set the decoder. . . . . . . . . . . . . . . . . . . . . . . 26

Video Doctor (Self-Diagnosis) . . . . . . . . . . . . . . 27

Wide Screen Compatibility 16:9 . . . . . . . . . . . . . 27

1W Mode (Power save mode) . . . . . . . . . . . . . . 27

Recording from External Components . . . . . . . . 28

Copying from DVD to VCR. . . . . . . . . . . . . . . . . 28

General Playback features - DVD Part . . . . . . . . . 29

Playing a DVD or Video CD. . . . . . . . . . . . . . . . . . 30

Additional features . . . . . . . . . . . . . . . . . . . . . . . 30

 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 30

 Time Search . . . . . . . . . . . . . . . . . . . . . . . . 30

 Marker Search . . . . . . . . . . . . . . . . . . . . . . 30

 Last Scene Memory . . . . . . . . . . . . . . . . . . 30

 Screen Saver . . . . . . . . . . . . . . . . . . . . . . . 30

Playing an Audio CD or MP3/WMA file . . . . . . . . 31

Programmed Playback. . . . . . . . . . . . . . . . . . . . 31

 Repeat Programmed Tracks. . . . . . . . . . . . . 31

 Erasing a Track from Program List . . . . . . . . 31

 Erasing the Complete Program List . . . . . . . 31

Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . . . . 32

Slide Show. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Moving to another File . . . . . . . . . . . . . . . . . . . . 32

Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

To rotate picture. . . . . . . . . . . . . . . . . . . . . . . . . 32

Playing a DivX Movie file . . . . . . . . . . . . . . . . . . . 33

Playing a DVD VR format Disc . . . . . . . . . . . . . . . 34

Additional Operation. . . . . . . . . . . . . . . . . . . . . . . 35

Maintenance and Service. . . . . . . . . . . . . . . . . . 35

Reference

Language and Area Code List . . . . . . . . . . . . . . . 36

Language Code List. . . . . . . . . . . . . . . . . . . . . . 36

Area Code List. . . . . . . . . . . . . . . . . . . . . . . . . . 36

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Page 6

Before Use

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.

This manual provides information on the operation and maintenance of your DVD player. Should the unit require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific DVD video disc.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier. A section whose title has one of the following symbols is

applicable only to the disc represented by the symbol.

ALL

All discs listed below

DVD

DVD and finalized DVD±R/RW

VCD

Video CDs

ACD

Audio CDs

MP3

MP3 files

WMA

DivX

WMA files DivX files

Notes on Discs

Handling Discs

Do not touch the playback side of the disc.Hold the disc by the edges so that finger pr ints do not get on the surface.Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case.Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth.Wipe the disc from the center out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

Selecting the Viewing Source

You must select one of your output sources (DVD or VCR) to view on the TV screen.



If you want to view DVD deck output source:

Press DVD until DVD indicator in the display window lights and output source of DVD deck is viewed on the TV screen.



If you want to view VCR deck output source:

Press VCR until VCR indicator in the display window lights and output source of VCR deck is viewed on the TV screen.

Introduction

Notes:

• If you inser t a disc while this unit is in the VCR mode,

this unit will switch to DVD mode automatically.

• If you inser t a cassette tape without prevention tab

while this unit is in the DVD mode, this unit will switch to VCR mode automatically.

Page 7

Before Use (Continued)

Types of Playable Discs

DVD (8 cm / 12 cm disc)

Video CD (VCD) (8 cm / 12 cm disc)

Audio CD (8 cm / 12 cm disc)

In addition, this unit plays DVD±R/RW, CD-R/RW and SVCD that contains audio titles, DivX, MP3, WMA, and/or JPEG files.

This indicates a product feature that is capable of playing DVD-RW discs recorded with Video Recording format.

Notes:

• Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal) since they may result in malfunctions.

• This unit requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality.Pre-recorded DVDs are automatically set to these standards.There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain preexisting conditions (see above) to ensure compatible playback.

Notes on Copyrights:

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs.When recording and playing the pictures of these discs picture noise will appear.This product incor porates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.

Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

Regional Code

This unit has a regional code printed on the rear of the unit.This unit can play only DVD discs labelled same as the rear of the unit or “ALL”.

Notes on Regional Codes

• Most DVD discs have a globe with one or more numbers in it clearly visible on the cover.This number must match your unit’s regional code or the disc cannot play.

• If you try to play a DVD with a different regional code from your player, the message “Check Regional Code” appears on the TV screen.

Page 8

Front Panel

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Introduction

1. Disc T ray Insert a disc here.

11//

Switches the unit to ON or OFF.

3. PROG. (V Channel Programme Selectors

4. DVD Opens or closes the disc tray.

5. Display window Shows the current status of the unit.

DVD: DVD deck is selected.

[P]: Indicates the Progressive Scan is set to On mode.

recording is programmed.

VCR: VCR deck is selected. REC:

TV:Indicates TV mode.

/v)

A disc is loaded in the DVDdeck.

Indicates repeat mode.

DVD+VCR is in timer recording or a timer

A Cassette is in the VCR deck. VCR recording is engaged.

DVD to VHS copy is in progress.

(See Notes on page 22.)

Indicates total playing time/elapsed time/current time.

6. Remote Sensor Point the remote control here.

7. Tape Compar tment

8. VCR Tape Eject

..//mm

9. Go to beginning of current chapter/track or to PREVIOUS chapter/track. Press and hold for two seconds for a fast reverse search. Rewinds the tape.

10. Starts playback.

MM//>>

11. Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search.Winds the tape forwards.

12. Stops playback.

13.DVD/VCR DVD/VCR Selector

14.Video IN Jack

15.

Audio IN (L/R) Jacks

Page 9

Remote Control

AAA

Switch this unit ON or OFF.

POWER

OPEN/CLOSE

EJECT

Open or close the disc tray.

Tape Eject.

TV/VCR

Switch between your TV’s tuner and

the VCR’s inter nal tuner.

DVD/VCR selection switch

Selects operation mode of

the remote control.

Switches modes of the device.

Select input source for

recording into tape.

PAUSE/STEP ( )

Pause playback temporarily / press

repeatedly for frame-by-frame

playback.

SKIP (. / >)

Go to next chapter or track.

Returns to beginning of current

chapter or track or go to previous

chapter or track.

STOP (

ÁÁ

Stops playback.

BACKWARD / FORWARD (m / M)

DVD:Search backward or forward. VCR: Rewinds the tape during the STOP mode, for fast reverse picture search and

Advances the tape during the STOP

mode, fast forward picture search.

PLAY (G)

Starts playback.

MARKER

Mark any point during playback.

Display MARKER SEARCH menu.

TITLE

Display the title menu of the

disc if available.

REC/ITR (

Record your input sources into tape.

REPEAT

Repeat chapter, track, title, all.

RANDOM/CM SKIP

Play tracks in random order.

CM SKIP

DISPLAY CLK/CNT

Access the On-Screen Display. Shows you the current time or counter.

FGDE(left/right/up/down)

Select an item in the menu.

PR/TRK(D / E)

Select channel programme of VCR. To adjust tracking. To control vertical tremble during picture still.

DISC MENU

Access menu of a DVD disc.

ENTER/OK

Acknowledge menu selection.

SETUP/ i

Access or remove setup menu.

RETURN

Displays the menu of a video CD with PBC.

0-9 numerical buttons

Select numbered items in a menu.

PROGRAM

Access or remove program menu.

CLEAR

)

Clear a track number on the program menu or a mark on the MARKER SEARCH menu. Reset tape counter to zero.

AUDIO

Select an audio language (DVD).

SUBTITLE

Select a subtitle language.

ANGLE

Select DVD camera angle if available

ZOOM

Enlarge video image.

A-B/LP

Repeat sequence. Select the recording speed of the tape.

VIDEO Plus+

)

To display the programme menu for VIDEO Plus+ programming.

Remote Control Operation

Point the remote control at the remote sensor and press the buttons.

Do not mix old and new batteries and never mix

Remote control battery installation

Detach the battery cover on the rear of the remote control, and insert two batteries (size

AAA) with 3 and # aligned correctly.). different types of batteries such as standard, alkaline, etc.

Page 10

Rear Panel

AERIAL

Connect the aerial using this jack.

VIDEO/AUDIO OUT(Left/Right) (DVD/VCR OUT)

Connect to a TV with video and audio inputs.

COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr) (DVD EXCLUSIVE OUT)

Connect to a TV with Y Pb Pr inputs.

AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT)

Connect to an amplifier, receiver or stereo system.

Introduction

EURO AV2 DECODER

AV2/Decoder connector to connect an exter nal device or to connect a decoder to watch encrypted broadcasting channels.

EURO AV1 AUDIO/VIDEO (VCR IN+OUT / DVD OUT)

Connect to your TV set or another video recorder.

COAXIAL (Digital audio out jack)

Connect to digital (coaxial) audio equipment.

RF.OUT

Connect to your TV using this jack.

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

(DVD EXCLUSIVE OUT)

AC Power Cord

Connect to a power source.

Page 11

Connections

Caution:



Make sure this unit is connected directly to the TV. Set the TV to the correct video input channel.



Do not connect this unit’s AUDIO OUT jack to the phone in jack (record deck) of your audio system.

Connecting to a TV & Decoder (or Satellite)

Make one of the following connections, depending on the capabilities of your existing equipment.

Basic connection (AV)

1. Connect the EURO AV1 AUDIO/VIDEO on the rear panel of this unit to the SCART input socket on the TV using a SCART lead (S1).

2. Some TV broadcasters transmit encoded television signals which you can only see with a purchased or rented decoder.You can connect such a decoder (descrambler) to this unit (S2).

1. Connect the VIDEO (DVD/VCR OUT) jacks on the DVD Player to the corresponding in jacks on the TV using the video cable (V).

2. Connect the Left and Right or AUDIO (DVD/VCR OUT) jacks of the DVD+VCR to the audio left/r ight in jacks on the TV using the audio cables (A1).

Note: The encoded television signals (CANAL+ or PRE-

MIERE) are not decoded in the 1W Mode (see p. 27).

Basic connection (RF)

1. Connect the RF antenna cable from your indoor/ outdoor antenna to AERIAL jack on the rear panel of this unit.

2. Connect the supplied RF antenna cable from the RF.OUT jack on the rear panel of this unit to your television’s Antenna Input (R).

DVD exclusive out connection

Component Video connection

1. Connect the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks on the DVD Player to the

corresponding in jacks on the TV using the Y Pb Pr cable (C).

2. Connect the Left and Right AUDIO OUT jacks of this unit to the audio left/right in jacks on the TV using the audio cables (A2).

Progressive Scan connection



If your television is a high-definition or “digital ready” television, you may take advantage of the DVD Player’s progressive scan output for the highest video resolution possible.



If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD Player.

1. Connect the COMPONENT/ PROGRESSIVE SCAN VIDEO OUT jacks on the DVD Player to the corresponding in jacks on the TV using the Y Pb Pr cable.

2. Connect the Left and Right AUDIO OUT jacks of the this unit to the audio left/right in jacks on the TV using the audio cables.

Notes:



Set the Progressive to “On”on the setup menu for progressive signal, see page 18.



Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack).

Rear of TV

VIDEO INPUT

COMPONENT VIDEO INPUT/

PROGRESSIVE SCAN

Pb Y

AUDIO INPUT

SCART INPUT

AERIAL

Rear of TV

VIDEO

AERIAL

Rear of this unit (Basic connection)

COMPONENT VIDEO INPUT/

INPUT

PROGRESSIVE SCAN

Pb Y

VA1

AUDIO INPUT

SCART INPUT

Decoder (or Satellite)

C A2

Rear of this unit (DVD exclusive out connection)

Page 12

Connections (Continued)

AUDIO INPUT

DIGITAL INPUT

COAXIAL

Amplifier (Receiver)

Rear of this unit

Digital multi-channel connection (DVD exclusive out connecttion)

DVD exclusive out

DVD/VCR OUT

Rear of this unit

Connecting to Optional Equipment

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic II/Pro Logic

Connect the Left and Right DVD/VCR AUDIO OUT or AUDIO OUT (DVD EXCLUSIVE OUT) jacks on this unit

to the audio left and right in jacks on your amplifier, receiver or stereo system, using the audio cables.

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2 or DTS)

1. Connect one of this unit’s DIGITAL AUDIO OUT jack (COAXIAL) to the corresponding in jack on your amplifier.Use an optional digital (coaxial) audio cable.

2. You will need to activate this unit’s digital output. (See “AUDIO” on page 19).

Digital Multi-channel sound

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your unit (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.

Warning:

Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

Notes:



If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.



To see the audio format of the current DVD in the On-Screen Display, press AUDIO.

Preparation

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc.

Page 13

Before Operation-VCR part

Tuning in a video channel on your TV

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the DVD+VCR through the RF cable.

If you have used a SCART lead you will not have to tune your TV, simply select the AV channel.The AV channel is already pre-tuned for optimum video playback on your TV.

Perform the following steps only if interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area, or if you change the connection from RF connection to AV connection, or vise versa.

1. Turn on DVD+VCR and TV.

2. Set the vacant position 36 on your TV.

3. Press POWER on the remote control to enter the

stand by mode (the clock indicator will be dimmed).

4. Press and hold PROG. (vvorVV) on the DVD+VCR for more than 4 seconds.

RF 36 will appear in the display. The following picture will be displayed on the TV screen.

Using your VCR for the very first time

Following picture will display on the TV screen when you have just connected your video recorder for the very first time.

To make tuning TV stations, please follow stages 3 to 4 as shown "ACMS" (see p.13).

ACMS

Pr-12

RF CHANNEL 36

If the picture is snowy, move to step 5. If the picture is clean, press POWER on the DVD+VCR to finish.

5. Press PROG. (vvorVV) on the DVD+VCR to set the video channel to a vacant position between 22 and 68 which is not occupied by any local station in your area.

Note:

The RF channel will not change until step 6 has been executed.

6. Press POWER to store the new RF video channel into the DVD+VCR memory. Now tune your TV set to the new DVD+VCR RF channel.

Note

If the TV picture was clear in step 4, do not retune your TV.

Page 14

Before Operation-VCR part

Setting the clock Manually

The clock in your DVD+VCR controls time and date settings for your DVD+VCR. The clock is set automatically during ACMS (Automatic Channel Memory System) when your DVD+VCR detects a channel that broadcasts a Teletext signal. If the broadcast signal is weak the clock will not be set and will require setting manually.

1. Press i. Press bbor BBto select SET.

Press ENTER/OK. The ACSS mode can be set to “OFF”by pressing

ENTER/OK if you want to set the time manually.

HH MM DD MM YY

:..- -

- -

SET

2. Use the vvorVVon the remote control to alter the HOURS, MINUTES, DAY, MONTH and YEAR. Please note your DVD+VCR uses a 24 hour clock. e.g. 1pm will be displayed as 13:00. The day of the week will appear automatically when you enter the year.

- - - -

ACSS : ON

- - - - -

To set the colour system

1. Press i.

2. The main menu will appear on the TV screen.

3. Press 1 or 2 to select the SYS and press ENTER/OK.

4. Press 3 or 4 to select according to the COLOUR system used.

SET

OSD

OSD ON OFF

SYS

5. Press 2 to select the RF AUDIO. Press 3 or 4 to select according to the RF AUDIO used.

SET

OSD

OSD ON OFF

SYS

6. Press i to remove the menus from the TV screen.

SYS

Preparation

HH MM DD MM YY

:..00 1 01 06 SUN 8

SET

ACSS : OFF

3. If you make a mistake press bbor BBand enter the correct details.

4. Press i to return to a TV picture.

Page 15

Before Operation-VCR part

SYS

SET

OSD ON OFF

OSD

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

ACMS

Pr-12

ACMS

Pr-12

ACMS

,DELETE :

MOVE :

SET

02 C03 00 03 C04 00 04 C05 00 05 C06 00 06 - - - 07 - - - 08 - - - -

01 C02 00

BBC2 ITV CH4 CH5

- - - - -

BBC1

01 C02 00 02 C03 00 03 C04 00

Pr-12

ACMS

BBC1 BBC2 ITV

How to use the main menu

This DVD+VCR can easily be programmed by using the menus displayed on screen. The menus are controlled by the Remote Control Handset.

1. Switch on your TV set and DVD+VCR by pressing the POWER button.

2. Press i button. The main menu will appear on the TV screen.



REC - Timer recording setting (see p.24).



PR SET - Manual tuning setting (see p.15).



ACMS - ACMS (Automatic Channel Memor y

System) (see p.14).



SET - Date & clock setting (see p.13).



SYS - To set the Colour TV System (see p.13).



1 W ON/OFF - Power Save Mode (see p.27).



(Dr.) - To check a problem with your VCR

(see p.27).



F.OSD ON/OFF - To display the operational

mode of your VCR (see p.26).



(16:9/4:3) - To select the aspect ratio of your

TV (see p.27).



DECODER - To use a pay-TV decoder

(or Satellite) with your VCR (

see p.26



(OPR) - To improve the playback picture

(see p.21). Appear when playback only.

O NIC -

To activate or deactivate the NICAM digital sound (

see p.26

Tip

You can change the menu language on the DVD setup menu. (See the Menu Language on page 18.)

3. Press 1 and 2 to select the desired menu. Press ENTER/OK and use 3 or 4 to select.

4. Press i to return to a TV picture.

Tuning in TV Stations Automatically

If the TV broadcast signal is weak your DVD+VCR may not detect the necessary information and will not be able to store them correctly. To overcome this problem please turn to the MANUAL TUNING section on page 15.

1. Press POWER to tur n on your DVD+VCR.

2. Press i button. The main menu will appear on the TV screen.

Press 1 or 2 to select the ACMS. Press ENTER/OK.

3. Press OK to again to start the automatic tuning process.

4. The TV STATION TABLE will appear when tuning is completed. Press i to save your settings.

Notes:

Please note currently only a limited number of TV companies transmit the Programme Delivery Control (PDC) signal which enables your DVD+VCR to successfully identify and store them. If your DVD+VCR has difficulty in identifying a TV station please turn the page to find out how to manually tune in and name a TV station. While automatic tuning is taking place the time and date will set automatically. If - - :- - appears in the DVD+VCR display it means that the broadcast signal is weak and the clock was not set. Please turn to CLOCK SET section of this book on page 13.

Page 16

Before Operation-VCR part

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

PR CH MFT STATION 01 00

CHANNEL/CABLE : AV

C03

SET

PR-03

02 C02 00 PR-02 03 C03 00 PR-03

04 - - - - - - - - -

05 - - - - - - - - 06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

,DELETE :

MOVE :

SET

PR CH STATION 04 - - - - - -

MFT

SET

C - -

CHANNEL/CABLE : AV

PR CH MFT 04 00C04

STATION

SET

PR CH MFT

STATION

04 00

C04

PR-04

SET

02 C02 00 PR-02 03 C03 00 PR-03

04 C04 00 PR-04

05 - - - - - - - - 06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

,DELETE :

MOVE :

SET

PR CH STATION 04 00

C04

MFT

CHANNEL/CABLE : AV

SET

Tuning in TV Stations Manually

In certain areas of the country broadcast signals may be too weak for your DVD+VCR’s automatic tuning process to find or assign TV stations correctly. You must tune in these weaker broadcast stations manually in order for your DVD+VCR to store them.

1. Press i.

The main menu will appear on the TV screen.

1 or 2 to select the PR SET.

Press Press ENTER/OK.

6. Press 2 to select STATION so that you may name your TV station. Press ENTER/OK.

7. Use 3 or 4 to select letters and numbers for the station name.

Use 1 or 2 to move back and forth between characters. Press ENTER/OK.

8. Press i, confirm the station placement.

Preparation

2. Press i. The station table will appear.

3. Press 3 or 4 to select the programme number that you want to tune (for example, PR 04).

4. Press ENTER/OK. Press AV to select C (Standard stations) or S (Cable stations): C02 - C69, S01 - S41. Enter the channel number of station that you want to

tune, use 3 or 4 to find the required station.

5. Searching will stop when it locates a stations. Press 2 to select MFT. Control the fine tuning of the station by using 3 or 4

If you wish to manually tune other stations repeat stages 3 - 8.

9. Press i again. Your new TV station has now been tuned into your DVD+VCR.

Page 17

Before Operation-VCR part

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

PR CH MFT STATION 01 00 PR-03

CHANNEL/CABLE : AV

C03

SET

02 C02 00 PR-02

03 C03 00 PR-03

04 C04 00 PR-04

05 - - - - - - - - 06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

,DELETE :

MOVE :

SET

02 C02 00 PR-02

03 C03 00 PR-03 04 C04 00 PR-04

05 - - - - - - - - 06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

SET

02 C02 00 PR-02

03 C04 00 PR-04 04 - - - - - - - - 05 C03 00 PR-03

06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

SET

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

PR CH MFT STATION

01 00 PR-03

CHANNEL/CABLE : AV

C03

SET

02 C02 00 PR-02

03 C04 00 PR-04 04 - - - - - - - - 05 C03 00 PR-03

06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

SET

,DELETE :

MOVE :

02 C02 00 PR-04

03 - - - - - - - - 04 C03 00 PR-03 05

06 - - - - - - - - -

- - - - - - - - -

07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-02

SET

,DELETE :

MOVE :

02 C02 00 PR-02

03 C04 00 PR-04 04 - - - - - - - - -

05 C03 00 PR-03

06 - - - - - - - - 07 - - - - - - - - 08 - - - - - - - - -

01 C01 00 PR-01

SET

,DELETE :

MOVE :

Changing the order of TV Stations

After tuning TV stations into your DVD+VCR you may wish to change the order in which they are stored without having to retune them again.The instructions given on this page will show you how you can simply move them into your desired order.

1. Press i. The main menu will appear on the TV screen. Press 1 or 2 to select the PR SET. Press ENTER/OK.

2. Press i. Press 3 or 4 to select the programme number you want to move (for example, PR-03). Press 2.

Deleting TV Stations

After tuning TV stations into your DVD+VCR you may wish to delete a station. The instructions given on this page will show you how you can easily delete any unwanted TV stations.

1. Press i. The main menu will appear on the TV screen. Use 1 or 2 to select the PR SET. Press ENTER/OK.

2. Press i.

3. Press 3 or 4 to select the programme number you want to delete. (for example, PR-01)

3. Press 3 or 4 to select the programme number you want to move to (for example, PR-05).

4. Press ENTER/OK. The selected programme will be moved to the new programme number. If you wish to move other TV stations repeat stages 1 - 4.

5. Press i to remove the menus from the TV screen.

4. Press 1. After a short while, the selected station will be deleted. If you wish to delete other TV stations repeat stages 3 - 4.

5. Press i to remove the menus from the TV screen.

Page 18

Before Operation-DVD part

1 / 12

1 / 3

0:20:09

ABC

1 ENG

1 / 1

3D SUR

Menu Language

Original

English

Off Original

Disc Audio Disc Subtitle Disc Menu

Move

Select

LANGUAGE

Displaying Disc Information on-screen

You can display various information about the disc loaded on-screen.

1. Press DVD to switch the device into DVD mode.

2. Press DISPLAY to show various playback information. The items displayed differ depending on the disc type or playing status.

3. You can select an item by pressing v / V and change or select the setting by pressing b / B.



Title (Track) – Current title (or track) number/total number of titles (or tracks)



Chapter – Current chapter number/total number of chapters



Time – Elapsed playing time



Audio – Selected audio language or channel



Subtitle – Selected subtitle



Angle – Selected angle/total number of angles



Sound – Selected sound mode

Note:

If no button is pressed for a few seconds, the on-screen display disappears. If no key is pressed for several seconds the screen disappears.

Initial Settings

By using the DVD Setup menu, you can make various adjustments to items such as picture and sound.You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 17 to 20.

To display and exit the Menu:

Press SETUP to display the menu.A second press of SETUP will take you back to initial screen.

To go to the next level:

Press B on the remote control.

To go back to the previous level:

Press b on the remote control.

General Operation

1. Press DVD on the remote control.

2. Press SETUP. The Setup menu appears.

3. Use v / V to select the desired option then press B to move to the second level. The screen shows the current setting for the selected item, as well as alternate setting(s).

4. Use v / V to select the second desired option then press B to move to the third level.

5. Use v / V to select the desired setting then press ENTER/OK to confirm your selection. Some items require additional steps.

Preparation

6. Press SETUP or NNexit the Setup menu.

Page 19

Before Operation-DVD part

Menu Language

Original

English

Off Original

Disc Audio Disc Subtitle Disc Menu

Move

Select

LANGUAGE

DISPLAY

TV Aspect

Widescreen

16 : 9

Display Mode

OffProgressive Scan

Move

Select

TV Output Select RGB

LANGUAGE

Menu Language

Select a language for the VCR and DVD’s setup menu and information display.

Disc Audio / Subtitle / Menu

Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu.

Original: Refers to the original language in which the disc was recorded.

Other:To select another language, press number buttons then ENTER/OK to enter the corresponding 4-digit number according to the language code list in the reference chapter (see page 36). If you enter the wrong language code, press CLEAR.

DVD

DISPLAY

TV Aspect

4:3 :

Select when a standard 4:3 TV is connected.

16:9 : Select when a 16:9 wide TV is connected.

Display Mode

Display Mode setting works only when the TV Aspect mode is set to “4:3”.

Letterbox: Displays a wide picture with bands on the upper and lower portions of the screen.

Panscan:

entire screen and cuts off the portions that do not fit.

DVD

Automatically displays the wide picture on the

Progressive Scan

Progressive Scan Video provides the highest quality pictures with less flickering. If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On.

To turn On progressive scan:

Connect component out of this unit to the input of your monitor/television, set your television or monitor to Component Input.

1. Select “Progressive Scan” on the DISPLAY menu then press B.

DISPLAY

TV Aspect

Display Mode

TV Output Select

OnProgressive Scan

Off

Move

Enter Prev.

2. Select “On” using the v / V buttons.

3. Pressing ENTER/OK will set this unit to Progressive scan mode.

Caution:

Once the setting for progressive scan output is entered, an image will only be visible on a progressive scan compatible TV or monitor. If you set Progressive Scan to On in error, you must reset the unit.

1) Remove any disc from the unit and close the disc

tray. See that “DISC” is displayed on the display window.

2) Press STOP on the remote control and hold it for five

seconds before releasing it.The video output will be restored to the standard setting and a picture will once again be visible on a conventional analog TV or monitor.

TV Output Select

Set this unit TV Output Select options according to the TV connection type.

YPbPr: When your TV is connected with the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks on this unit.

RGB: When your TV is connected with the SCART (RGB signal) jack.

Page 20

Before Operation-DVD part

Dolby Digital

Bitstream PCM 48KHz On

Bitstream DTS MPEG Sample Freq. DRC

OnVocal

Move

Select

AUDIO

LOCK

Rating

New DG

Unlock Password Area Code

Move

Select

AUDIO

Each DVD disc has a variety of audio output options. Set this unit’s AUDIO options according to the type of audio system you use.

Dolby Digital / DTS / MPEG

Bitstream: Select “Bitstream” if you connect the

DVD+VCR’s DIGITAL AUDIO OUT jack to an amplifier or other equipment with a Dolby Digital, DTS or MPEG decoder.

PCM (for Dolby Digital / MPEG): Select when connected to a two-channel digital stereo amplifier. DVDs encoded in Dolby Digital or MPEG will be automatically downmixed to two-channel PCM audio.

Off (for DTS): If you select “Off ”, the DTS signal is not output through the DIGITAL AUDIO OUT jack.

Sample Freq. (Frequency)

DVD

If your receiver or amplifier is NOT capable of handling 96 kHz signals, select 48 kHz.When this choice is made, this unit automatically converts any 96 kHz signals to 48 kHz so your system can decode them.

If your receiver or amplifier is capable of handling 96 kHz signals, select 96 kHz.When this choice is made, this unit passes each type of signal through without any further processing. Check the documentation for your amplifier to verify its capabilities.

DRC (Dynamic Range Control)

With the DVD for mat, you can hear a program’s soundtrack in the most accurate and realistic presentation possible, thanks to digital audio technology. However, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones).This allows you to listen to a movie at a lower volume without losing clarity of sound. Set DRC to On for this effect.

Vocal

Set to On only when a multi-channel karaoke DVD is playing.The karaoke channels on the disc mix into normal stereo sound.

DVD

DivXDVD

DVD

LOCK (Parental Control)

Preparation

Rating

Blocks playback of rated DVDs based on their content. Not all discs are rated.

1. Select “Rating” on the LOCK menu then press B.

2. To access the LOCK options, you must input the password you have created. If you have not yet entered password, you are prompted to do so.

Input a password and press ENTER/OK.Enter it again and press ENTER/OK to verify. If you make a mistake before pressing ENTER/OK, press CLEAR.

3. Select a rating from 1 to 8 using the v / V buttons.

Rating 1-8: Rating one (1) has the most restrictions and rating eight (8) is the least restrictive.

Unlock: If you select unlock, parental control is not active and the disc plays in full.

4. Press ENTER/OK to confirm your rating selection, then press SETUP to exit the menu.

Password

You can enter or change password.

1. Select Password on the LOCK menu then press B.

2. Follow step 2 as shown above (Rating). To change the password, press ENTER/OK when the

“Change” option is highlighted. Input a password and press ENTER/OK. Enter it again and press ENTER/OK to verify.

3. Press SETUP to exit the menu.

If you forget your password

If you forget your password, you can clear it using the following steps:

1. Press SETUP to display the Setup menu.

2. Input the 6-digit number “210499” and press

ENTER/OK.The password is cleared.

Page 21

Before Operation - DVD part

PBC

Off

Move

Auto Play

OTHERS

Select

SelectDivX(R) VOD

Area Code

DVD

Enter the Area Code whose standards were used to rate the DVD video disc, based on the list in the reference chapter (see page 36).

1. Select “Area Code” on the LOCK menu then press B.

2. Follow step 2 as shown left (Rating).

3. Select the first character using v / V buttons.

4. Press B and select the second character using v / V buttons.

5. Press ENTER/OK to confirm your area code selection.

OTHERS

The PBC and Auto Play and Divx(R) settings can be changed.

DivX(R) VOD

We provide you the DivX®VOD (Video On Demand) registration code that allows you to rent and purchase

videos using the DivX®VOD service. For more information, visit www.divx.com/vod.

1. Select “DivX(R) VOD” option then press B.

2. Press ENTER/OK while “Select” is selected and the registration code will appear. Use the registration code to purchase or rent the

videos from DivX®VOD service at www.divx.com/vod. Follow the instructions and download the video onto a disc for playback on this unit.

3. Press ENTER/OK to exit.

4. Press i to remove the menu.

Note:

All the downloaded videos from DivX®VOD can only be played back on this unit.

PBC

VCD

Set Playback Control (PBC) to On or Off. On:Video CDs with PBC are played according to the

PBC.

Off:Video CDs with PBC are played the same way as

Audio CDs.

Auto Play

DVD

You can set up the DVD+VCR so a DVD disc automatically starts playing whenever the DVD is inser ted. If Auto Play mode is set to On, this DVD player will search for title that has the longest playback time and then play back the title automatically.

Note:

The Auto Play function may not work for some DVDs.

Page 22

Operation with tape

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

OFF SOFT SHARP

Playing a tape

You will only be able to load and eject video cassettes when your DVD+VCR is plugged into the mains. Your DVD+VCR may also playback recordings from NTSC tapes (on PAL TV).

Getting a better picture

When a cassette is inserted and playback started, the automatic tracking function works to get the best possible picture automatically. If the quality of the recording is poor, repeatedly press manually adjust the tracking until any distortions have been removed.

1. Make sure that you have correctly connected your DVD+VCR as described earlier in this book. Turn on your TV. Press POWER to tur n on your DVD+VCR. Insert the video cassette into your DVD+VCR. The video cassette should have the window side facing up and the arrow facing away from you.

2. Press VCR to switch the device into VCR mode.

3. Press N to start playing your tape. If you load a video cassette which has had its record protection tab removed, playback of the cassette will start automatically.

AUTO TRACKING

Your DVD+VCR will automatically adjust the tracking to give the best picture quality.

4. Press PAUSE/STEP to still a picture. Press PAUSE/STEP repeatedly to advance the tape frame by frame. If you press FORWARD, the picture will be slowed down at about 1/19 times the normal playback. Tapes can be paused for up to 5 minutes. After 5 minutes your DVD+VCR will stop the tape to prevent damaging the tape or your DVD+VCR . Still picture quality can be improved slightly by using v or V.

5. Press N to continue playing your tape.

Double speed playback

Press the "N" button during normal playback.The tape will play back at double speed and without sound.

Press the "N" button to return to playback at normal speed

Picture search: During playing back press either BACKWARD or FORWARD to this will enable you to rapidly wind the

tape see where you are on the tape.

Logic search:

During fast forwarding or rewinding press and hold m or M the picture will be played back at 7 times

normal playback speed.

or 44on the remote control to

6. Slow motion playback

, Shuttle :

During playing back or still picture press F or G. You can reach the following playback speeds. (REV, PB 5-, PB 1-, Still, SLW, PLAY, 2PLY, CUE) To switch off the slow motion and shuttle, press the desired function. During slow motion and shuttle, the noise bars may appear on the picture according to the status of tape. If distortions can be seen in the picture, reduce them with v or V.

7. Press STOP to end playback. Press EJECT. If the end of the tape is reached, your DVD+VCR will stop playback automatically, rewind, stop, eject the tape.

CM (Commercial Message) Skip:

This feature enables you during playback of a tape to skip a commercial break in a few seconds, then resume normal playback. While tape is playing press

CM SKIP

on the remote control to skip commercial (or another programme material).

Repeatedly press

CM SKIP

to skip:

1 Press 30 seconds 2 Press 60 seconds 3 Press 90 seconds 4 Press 120 seconds 5 Press 150 seconds 6 Press 180 seconds

OPR (Optimum Picture Response)

This feature automatically improves playback picture quality by adjusting your DVD+VCR to the condition of

the tape. Please note that the OPR icon ( ) will only appear in play that mode when playing a tape.

1. Press i.

2. Press b or B to select (OPR).

3. Press ENTER/OK.

4. Press

or 44repeatedly to select: OFF, SOFT or

SHARP. Please note you may only set OPR when

playing a tape.

Off: The picture is displayed in original size Soft: Softer edges. Sharp: Shar per edges.

5. Press i return to screen.

Operation

Page 23

Operation with tape

Instant Timer Recording (ITR)

Your DVD+VCR allows you to make recordings using a variety of simple methods:

Instant Timer Recording (ITR) start recording immediately for a set period of time or until the video cassette runs out.

Your DVD+VCR incorporates Long Play (LP) which enables you to record up to twice the amount of time on a video cassette. For example an E-180 will record up to 180 minutes using Standard Play (SP); using LP you will be able to record up to 360 minutes.Please note there will be a slight loss in picture and sound quality when using LP.

1. Make sure that you have correctly connected your DVD+VCR as described earlier in this book. Press POWER to turn on your DVD+VCR.

2. Insert a video cassette with protection tab into your DVD+VCR. The video cassette should have the window side facing up and the arrow facing away from you.

3. Press33or 44to select the programme number you wish to record. You may also directly select programme number using the numbered buttons on the remote control.

4. If you wish to record directly from the SCART or RCA jacks, repeatedly press AV until the socket you wish to record from is displayed.

7. Press PAUSE/STEP to avoid recording unwanted scenes. Press PAUSE/STEP to continue recording.

Caution: If the key PAUSE/STEP is pressed for more than 5 seconds the recording is stopped and must be continued manually.

8. Press STOP to end recording. Press EJECT.

Notes:

 If you do not wish to record on a tape (this can hap-

pen quite easily by accident!) remove the protection tab on the back edge of the video cassette.

 It is possible to record on a video cassette with the

record protection tab removed by covering the hole with self adhesive tape.

 Remember you can record one programme while

watching another by starting your instant recording, press TV/VCR to select TV mode and then selecting a different channel on your TV.

AV 1 for recording from EURO AV1 SCART jacks on the rear of your unit. AV 2 for recording from EURO AV2 DECODER jacks on the rear of your unit. AV 3 for recording from VIDEO IN and AUDIO IN (Left & Right) jacks on the front of your unit.

5. Press LPif you wish to record in Long Play or Standard Play. SP will produce improved picture and sound quality, however LP will provide twice as much recording time as SP.

6. Press REC/ITR on the remote to star t recording. Press REC/ITR on the remote several times. Each successive press will increase the record time by 30 minutes until you reach a maximum of 9 hours.

Page 24

Operation with tape

VIDEO Plus+ Programming

VIDEO Plus+ greatly simplifies entering the date, channel, start and end times of a Timer Recording by simply entering PlusCode Programming numbers. PlusCode Programming numbers are published in most TV guide magazines; they can vary one to nine numbers in length. VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation.The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.

1. Make sure that TV channels have been tuned and stored in correct Insert a video cassette with protection tab into your DVD+VCR.

2. Press VIDEO Plus+.

3. Press the numbered buttons to enter the

PlusCode of the TV programme that you wish to

record. If you make a mistake press revised number.

4. Press OK. If PLEASE CHECK is displayed it means that you have entered the wrong PlusCode Programming numbers, entered the PlusCode Programming numbers incorrectly. If “- -” is displayed, you have to enter the programme number of the station, you want to record from.

VIDEO Plus+ order.

VIDEO PLUS+ CODE NO.

- - - - - - - - -

REC

VIDEO PLUS+ CODE NO.

246876543

REC

PR DATE TIME

PR-01 12

- - - -

0~9,

11 11 55~::

- - - - - - - -~::

0~9,

F then enter the

DELETE :

SP SP SP SP SP SP SP

6. Press

G to select the recording speed.

( in Timer menu = VPS activated; no in Timer menu = VPS deactivated)

D or E to select the desired tape speed

Press (SP, IP, or LP). IP mode determines how much tape is left and switches speed from SP to LP, if necessary, to complete recording the program. IP mode is not selected when VPS is ON. Check that the timer event details are correct. If you wish to record from AUDIO IN and VIDEO IN on the front or from either of the EURO SCART sockets on the back of VCR, press AV to select for correct display (AV1, AV2 or AV3).

PR DATE TIME

PR-01 12

- - - -

- - - - - - - -~::

11 11 55~::

SP SP SP SP SP SP

7. If you want to make another VIDEO Plus+ recording repeat stages 2 - 7. Press i twice. If PLEASE CHECK is displayed, you have entered incorrect information and will need to re-enter the data. Press POWER to switch your DVD+VCR power off mode.

will appear in the video recorder’s display while your VCR waits to make the recording. To watch a DVD during timer recording standby mode, press POWER and DVD to switch to DVD mode.

8. Press POWER to end recording.

 Programme Delivery Control (PDC)

The Programme Delivery Control (PDC) system adjusts the start and end times of a timer record event.This can be particularly useful with spor ts events which may run over into extra time.The PDC signal is transmitted by the broadcaster and this controls your video recorder’s timer. Currently only a limited number of TV companies transmit PDC signals. Please make sure that when recording from channels that do not broadcast PDC that you turn PDC OFF.

Note:Timer recordings can only be performed if the device is in stand-by mode.

Operation

5. Press

F or G to select the settings that you wish to

revise.(PR, DATE, TIME VPS and SP).

D or E to enter the correct information.

Press

PR DATE TIME

PR-01 12

- - - -

11 11 55~::

- - - - - - - -~::

SP SP SP SP SP SP SP

Page 25

Operation with tape

PR DATE

T I M E

- - - -

- -

- - - - SP

- -

- - - - - - - -~::

DELETE:

PR DATE

T I M E

- - - -

- SP

- - - - SP

PR-03

- - - - - - - -~::

PR DATE

T I M E

- - - - SP

PR-03 4

- - - - - - - -~::

DLY SU MO TU WE TH FR SA

41400 1530~::

PR DATE

T I M E

- - - - SP

PR-03

- - - - - - - -~::

41400 1530~::

PR DATE

T I M E

- - - - SP

PR-03

- - - - - - - -~::

41400 1530~::

PR DATE

T I M E

- - - - SP

PR-03

- - - - - - - -~::

PDC : ON

Timer recording using On Screen Display

You may set up to seven timer record events within one month of the current date.

Note:

Before setting the timer make sure that you have set the DVD+VCR clock correctly and you know which stations you have tuned TV stations on your DVD+VCR.

1. Insert a video cassette with protection tab into your DVD+VCR. The video cassette should have the window side facing up and the arrow facing away from you.

2. Press i. Press 1 or 2 to select REC ( ).

Press ENTER/OK.

3. Press ENTER/OK to start setting the timer record event.

4. Use the PR/TRK (v/V) to enter the station that you wish to record then press 2.

6. Use v/V/1/2 buttons to enter the recording start and end times of the programme that you wish to record.

Please note your DVD+VCR uses a 24 hour clock. e.g. 1pm will be displayed as 13:00.

7. Press B and press v or V to switch PDC on or off.

8. Press B to select the recording speed. Press v or V to select the desired tape speed (SP, IP, or LP). IP mode determines how much tape is left and switches speed from SP to LP, if necessary, to complete recording the program. IP mode is not selected when PDC is ON.

Note:

If all timer record events are full press v or V to select the event that you wish to remove and replace.

Press b to delete the event.

5. Use the PR/TRK (v/V) to enter the date of the programme. If you press ENTER/OK before entering the date you may select one of the following automated recording features.

Press 1 or 2 to select, then press ENTER/OK to confirm. DLY To record every day (except Saturday and Sunday) at the same time. SU~SA To record at the same time every week.

Page 26

Operation with tape

Timer recording using On Screen Display (Continued)

9. Press i to set another timer record event and follow steps 3 to 8. Check that the timer event details are correct. Press i return to screen.

If PLEASE CHECK is displayed, you have entered incorrectly and will need to re-enter the data.

10.Press POWER to switch your DVD+VCR to Timer Standby mode.

Note: The 1W Mode is not available in the standby mode for the timer recording.

The timer symbol ( ) will appear in the display window while your DVD+VCR waits to make the recording.

11.Press POWER to end timer recording.

Notes:

 The DVD+VCR will automatically power off when

Timer Recording ends.

 During timer recording standby mode, the DVD and

VCR mode cannot be operated.To use the DVD+VCR, press POWER. After you use the DVD or VCR, press POWER again to put the VCR into timer recording standby mode.

 If at a later date you wish to delete or change any of

the settings in timer event memory you may do so without having to enter all the timer event information again. Simply display the timer event screen.Use v or V to select the event that you wish to delete or change.

 Programme Delivery Control (PDC)

Operation

Press b to delete the event...or Press ENTER/OK to change; then press b or B to select; Station, Date, Start and End times and recording speed. Press v or V to enter the correct information.

 If Timer record events Overlap...

Make sure that the preset times of the timer recording events do not overlap.If they do, the earlier programme will always be given priority.

Example:

Programme 1 is programmed to start at 16:00 and end at 17:00. Programme 2 is programmed to start at 16:30 and end at 17:30. (In this case, Programme 1 will be recorded in its entirety, but only the last 30 minutes of Programme 2 will be recorded.)

 To watch a DVD while performing a timer recording,

press DVD to select DVD mode.

Page 27

Additional Operation - VCR part

Hi-Fi Stereo Sound System

Your VCR will record and playback Hi-Fi stereo sound. In addition it has a stereo NICAM digital stereo sound decoder.This allows you to record and playback the sound in several different ways.Video cassettes recorded on your VCR will have a normal mono audio track and two VHS Hi-Fi stereo audio tracks.These stereo tracks allow you to make audio recordings in Hi-Fi stereo or bilingual mode from a TV broadcast, stereo audio system, video disc or another Hi-Fi VCR.

1. Your VCR’s NICAM digital sound decoder allows you to enjoy broadcasts with NICAM sound, as well as standard stereo, bilingual and mono sound.The particular type of sound received or that recorded will be briefly displayed on the TV screen for a couple of seconds:

STEREO NICAM

Sound is automatically recorded on the Hi-Fi stereo and mono tracks of the video tape.

BIL NICAM

Both audio channels will be recorded on the Hi-Fi stereo tracks.The pr imar y language channel (left) will be recorded on the mono track of the video tape.

MONO

The sound is recorded on the Hi-Fi tracks and the mono track of the video tape without any separation.

2. Press AUDIO repeatedly until the desired audio mode appears.

3. The choice is STEREO, LEFT, RIGHT and MONO. In BIL NICAM playback the primary language is out- put on the left channel and the secondary channel is output simultaneously from the right channel when audio output is set to STEREO. The primary language will be output from both channels when the audio setting is MONO. Please note that when adjusting the tracking control Hi-Fi stereo sound may revert to MONO.

Tape Counter Memory Stop

The Digital Tape Counter can be displayed on the dis- play window instead of the time by pressing CLK/CNT on the remote control.The Digital Tape Counter indicates the relative positions of recordings on the tape.

1. Press CLK/CNT. Press CLEAR to set the counter to 0:00:00. Press N or start recording. The tape counter will display the actual play time in hours, minutes and seconds.

2. Press x when playback or recording is complete.

Press m. The tape will rewind and automatically stop when the counter returns to 0:00:00.

To set the decoder

We have already described, how to connect a decoder for pay-TV station as CANAL+ or PREMIERE on page

10. For the recording of an encoded station you do not

have to control anything. You just select the station and wait shortly until the decoding will start.

1. Press i. The main menu will appear on the TV screen. Press

F or G to select the DECODER.

Press ENTER/OK.

2. Press

3. Press i to retur n to a TV picture.

D or E to select.

ON: When the decoder is connected to the AV2 socket. OFF: When another VCR is connected to the AV2 socket.

On Screen Display (F.OSD)

You may easily display the current time or tape counter, amount of tape left, day, month, year, day of week, programme channel, tape speed and operational mode of your DVD+VCR on the TV screen.If a recording is taking place these On Screen Displays will not be recorded onto the tape.

1. Press CLK/CNT to display. Press CLK/CNT repeatedly to cycle through the display options.The tape counter and amount of tape left will appear if there is a tape loaded.

2. After 3 seconds the majority of the On Screen Displays will clear leaving only the clock or tape counter and the amount of tape left on the screen. Press CLK/CNT again to remove all displays from the TV screen.

Page 28

Additional Operation - VCR part

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

ANTENNA CONNECT

PLEASE CHECK

HEAD STATUS TAPE STATUS NO. OF TIMER PROGRAMME NEXT TIMER PROGRAMME

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

SYS

SET

OSD ON OFF

OSD

ACMS

Pr-12

SET

AUTO 4:3 16:9

Video Doctor (Self-Diagnosis)

This feature informs you that there is a problem with your DVD+VCR.These error messages will appear on the TV screen.

1. Press i. Press 11or 22to select . Press ENTER/OK.

2. Press 33or 44to check a problem.

ANTENNA CONNECT

O PLEASE CHECK:

Connect the aerial into the jack securely.

HEAD STATUS

O PLEASE CLEAN:

Clean your video heads.

TAPE STATUS

O NOT RECORDABLE:

Insert a tape with its protection tab in place

NO. OF TIMER PROGRAMME

O 2

Shows the number of timer recording.

NEXT TIMER PROGRAMME

O PR-01 26 10:00~11:00 SP

Shows the current status of timer recording.

3. Press i to remove the menus from the TV screen.

Wide Screen Compatibility 16:9

Your DVD+VCR can record and play back wide screen aspect ratio programmes (16:9).To record a wide screen format programme successfully the correct type of wide screen signal must be broadcast by the TV station.

1. Switch on your DVD+VCR. Press i.

F or G to select .

Press Press ENTER/OK.

2. Press v/V repeatedly to select: AUTO, 4:3 or 16:9.

AUTO (Playback mode only)

Automatically plays back Wide-Screen programmes as Wide-Screen and Normal programmes as normal.

4:3

Only for playing back and recording Normal format recordings (4:3).

16:9:

Only for playing back and recording Wide-Screen format recordings (16:9).

3. Press i to remove the menus from the TV screen. To enjoy Wide-Screen playback you must connect your VCR to the TV using a SCART cable.

Operation

1W Mode (Power save Mode)

Set 1W ON/OFF to ON to place your DVD+VCR into an economic power save mode. Nothing is displayed in the display window.

1 Press i.

The main menu will appear on the TV screen. Press

F or G to select the 1W ON/OFF.

Press ENTER/OK.

2. Press

3 Press i.

Notes:

Some function may not be operated in the 1W Mode.

• The 1W Mode is not available in the standby mode for

the timer recording and when turn Power off of the DVD+VCR after receiving the encoded television signals (CANAL+ or PREMIERE).

•

The encoded television signals (CANAL+ or PREMIERE) are not decoded in the 1W Mode.

D or E to select the ON.

Page 29

Additional Operation - VCR part

Recording from External Components

You can record from an external component, such as a camcorder or VCR, connected to any of the DVD+VCR’s external inputs.

1. Make sure that the component you want to record from is connected properly to the DVD+VCR.

2. Press AV repeatedly to select the exter nal input to record from.

3. Load a recordable tape.

4. Set a recording mode (SP or LP) as necessary by pressing LPrepeatedly.

5. Play the tape or disc in the external component.If you have a TV attached to your DVD+VCR, you can see the video playing.

6. Press REC/ITR on the Remote Control once to start recording. The REC indicator lights in the display window.

7. Press STOP to stop recording.

Notes:

• Before recording, confirm the recording start position.

• If your source is copy-protected using CopyGuard, you will not be able to record it using this unit.See Copyright on page 6 for more details.

•To record for a fixed length of time, see Instant Timer Recording.

Copying from DVD to VCR

You can copy the contents of a DVD to a VHS tape.

1. Insert the disc you wish to copy into the DVD deck and close the disc tray.

2. Insert a blank VHS video tape into the VCR deck.

3. Find the place on the DVD from which you want to start dubbing using the N, BACKWARD,

FORWARD and PAUSE functions. For best results, pause playback at the point from which you want to record.

4. Press REC/ITR on the Remote Control. The DVD goes into PLAY mode and the VCR goes into RECORD mode. If the DVD disc menu appears, you may need to press N manually to begin copying.

5. When the DVD is finished playing, press STOP to end copying.

Notes:

• If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc.It is not permitted to copy Macrovision encoded DVDs (or Discs). “LOCK” is displayed in the display window.

•You must stop the copy process manually when the DVD movie ends, or the unit may replay and record over and over again.

• When you stop the DVD playback during copying, the recording on VCR is stopped automatically.

Page 30

General Playback features - DVD Par t

Buttons Operations

Z (OPEN / CLOSE) Opens or closes the disc tray. X (PAUSE) During playback, press X to pause playback.

Press X repeatedly to play Frame-by-Frame.

. / > During playback, press . or > to go to the next

chapter/track or to return to the beginning of the current chapter/track.

Press . twice briefly to step back to the previous chapter/track.

m / M During playback, press m or M repeatedly to select the

required scan speed. DVD, DivX disc; 4 steps Video CD, MP3, WMA, Audio CD ; 3 steps

While the playback is paused, press M repeatedly to play in slow motion (4 steps, forward only).

REPEAT Repeatedly press REPEAT during playback to select the

desired repeat mode. DVD video discs:Chapter/Title/Off Video CDs, Audio CDs, DivX/MP3/WMA discs:Track/All/Off

A-B Press A-B to define the starting point of a section replay.

Press A-B again to define the ending point of a replay. Press A-B a third time to cancel the replay.

ZOOM During playback or pause mode, press ZOOM to enlarge the

video image (4 steps). You can move through the zoomed picture using bBvV

buttons.Press CLEAR to exit.

RANDOM During playback or in stop mode, press RANDOM for random

playback.

TITLE If the current DVD title has a menu, the title menu appears on

the screen. Otherwise, the disc menu may appears.

DISC MENU The disc menu appears on the screen.

(ANGLE) During playback of DVD disc contains scenes recorded differ-

ent camera angles, press ANGLE repeatedly to select a desired angle.

(SUBTITLE) During playback, press SUBTITLE repeatedly to select a

desired subtitle language.

(AUDIO) During playback, press AUDIO repeatedly to hear a different

audio language or audio track.

Discs

ALL ALL

DivXVCDDVD

ALL

Operation

ALL

DivXVCDDVD

ALL

VCDDVD ACDDivX

DivXVCDDVD

MP3ACD

WMA

DVD

DVD DVD

DivXDVD

VCD

Page 31

Playing a DVD or Video CD

Notes on general features:

• On a Video CD with PBC, you must set PBC to Off on the setup menu to use the repeat function (See “PBC” on page 20).

• If you press > once during Repeat Chapter (Track) playback, the repeat playback cancels.

• Zoom may not work on some DVDs.

• When you are playing a DVD disc contains scenes recorded different camera angles, the angle indicator will blink on the TV screen during scenes recorded at different angles as an indication that angle switching is possible

• The A-B repeat function is available only in the current chapter/track.

Additional features

3D Surround

To produce a 3D surround effect that simulates multichannel audio from two stereo speakers (instead of the five+ speakers normally required for multi-channel audio from a home theater system).

DivXVCDDVD

1. Press DISPLAY dur ing playback.

2. Use 3 or 4 to select the sound option.

The sound option will be highlighted.

3. Use 1 or 2 to to select “3D SUR”.

To turn off the 3D Surround effect, select “Normal”.

ACD

1. Press AUDIO during playback.

“3D SUR.” appears on the menu screen.

2. To return to nor mal playback, press AUDIO repeat-

edly until “3D SUR.” disappears from the menu screen.

Marker Search To enter a Marker

You can start playback from up to nine memorized points.To enter a marker, press MARKER at the desired point on the disc.The Marker icon appears on the TV screen briefly. Repeat to enter up to nine markers.

To Recall or Clear a Marked Scene

1. During disc playback, press SEARCH.The mar ker search menu appears on the screen.

2. Within 10 seconds, press b / B to select a marker number that you want to recall or clear.

3. Press ENTER and playback starts from the marked scene. Or, Press CLEAR and the marker number is erased from the list.

4. You can play any marker by inputting its number on the marker search menu.

Last Scene Memory

This player memorizes last scene from the last disc that is viewed.The last scene remains in memory even if you remove the disc from the player or switch off the player. If you load a disc that has the scene memorized, the scene is automatically recalled.

Note:

This player does not memorize the scene of a disc if you switch off the player before commencing to play the disc.

Screen Saver

The screen saver appears when you leave the DVD player in Stop mode for about five minutes.

DivXVCDDVD

VCDACDDVD

Time Search

To start playing at any chosen time on the disc:

1. Press DISPLAY dur ing playback.

2. Press v / V to select the time clock icon and “--:--:--” appears.

3. Use numerical buttons to input the required start time in hours, minutes, and seconds from left to right. If you enter the wrong numbers, press CLEAR to remove the numbers you entered.Then input the correct numbers.

4. Press ENTER to confirm. Playback starts from the selected time.

DivXVCDDVD

Page 32

Playing an Audio CD or MP3/WMA file

Program

List

Track1 Track2 Track3 Track4 Track5 Track6 Track7 Track8

AUDIO CD

0:52:07

1 / 12

Clear All

PROGRAM

Edit

Program

List

0:00:00

1 / 12

Clear All

PROGRAM

Edit

DISPLAY

Info

MUSIC

2-Music2

1-Music1

3-Music3 4-Music4 5-Music5 6-Music6 7-Music7

This unit can play Audio CDs or MP3/WMA files recorded media.

MP3/ WMA/ Audio CD

Once you insert an MP3/WMA files recorded media or Audio CD, a menu appears on the TV screen. Press v / V to select a track/file then press PLAY or ENTER and playback starts.You can use variable playback functions.Refer to page 29-30.

ID3 T AG

• When playing a file containing information such as

track titles, you can see the information by pressing DISPLAY. [ Song, Artist, Album, Comment, Genre ]

Tips:

• Press DISC MENU to move to the next page.

•To switch from the detailed list to the previous folder

list highlight the icon vVusing and press ENTER.

• On a CD with MP3/WMA and JPEG you can switch

MP3/WMA and JPEG. Press TITLE and MUSIC or PHOTO word on top of the menu is highlighted.

MP3 / WMA disc compatibility with this player is limited as follows:

• Sampling frequency: within 8 - 48 kHz (MP3), within 32 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3), 32 - 384 kbps (WMA)

• The player cannot read an MP3/WMA file that has a file extension other than “.mp3”/ “.wma”.

• CD-R physical format should be ISO 9660

• If you record MP3 / WMA files using software that cannot create a file system (eg. Direct-CD) it is impossible to playback MP3 / WMA files. We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system.

• File names should have a maximum of 8 letters and must incorporate an .mp3 or .wma extension.

• They should not contain special letters such as / ? * : “ < > l etc.

• The total number of files in a folder should be less than 1190 files.

Programmed Playback

The program function enables you to store your favorite tracks from any disc in the player memory. A program can contain 30 tracks.

1. Insert an Audio CD or MP3/WMA files recorded media. AUDIO CD or MUSIC menu appears.

2. Press PROGRAM.The mark will appear.

Note:

Press PROGRAM again to exit the program edit mode, then the mark will disappear.

3. Select a track on the “List”, then press ENTER to place the selected track on the “Program” list. Repeat to place additional tracks on the list.

4. Select the track you want to start playing on the “Program” list.

5. Press PLAY or ENTER to start. Playback begins in the order in which you programmed the tracks. Playback stops after all of the tracks on the “Program” list have played once.

6. To resume nor mal playback from programmed playback, select a track on the list and then press PLAY.

Repeat Programmed Tracks

Press REPEAT to select a desired repeat mode.

• Track: repeats the current track

• All: repeats all the tracks on the “Program” list.

• Off(No display): does not play repeatedly.

Note:

If you press > once during Repeat Track playback, the repeat playback cancels.

Erasing a Track from “Program” List

1. During STOP mode, press PROGRAM and

the mark will appear

2. Use vVb Bto select the track that you wish to erase from the Program list.

3. Press CLEAR. Repeat step 1~3 to erase additional tracks on the list.

Erasing the Complete Program List

1. During STOP mode, press PROGRAM and

the mark will appear

2. Use vVb Bto select “Clear All”, then press ENTER.

Note (in repeated playback only):

The programs are also cleared when the power is off or the disc is removed.

Operation

Page 33

Viewing a JPEG file

Preview

List

Folder 00 Folder 01 Folder 02 Folder 03

Folder 04 01 FILE 01 02 FILE 02 03 FILE 03

>>>

PHOTO

/FILE 01

This unit can play JPEG files recorded media.

1. Insert a JPEG files recorded media. The PHOTO menu appears on the TV screen.

2. Press v / V to select a folder, and press ENTER. A list of files in the folder appears.

3. If you want to view a particular file, press v / V to highlight a file and press ENTER or PLAY.

4. To return to the PHOTO menu while watching pictures, press STOP.

Tips:

• If you are in a file list and want to return to the previ-

ous Folder list, use v / V buttons to highlight and press ENTER.

• Press DISC MENU to move to the next page.

• There are three Slide Speed options : >>> (Fast),

>> (Normal) and > (Slow). Use vVbBto highlight . Then, use b / B to

select the option you want to use then press ENTER.

• On a disc with MP3/WMA and JPEG you can switch

MP3/WMA and JPEG. Press TITLE and MUSIC or PHOTO word on top of the menu is highlighted.

• While watching a picture, press RETURN to hide the

help menu.

Slide Show

Use vVbBto highlight the (Slide Show) then press ENTER.

Moving to another File

Press . or > or cursor (b or B) once while viewing a picture to advance to the next or previous file.

Zoom

During watching pictures, press ZOOM to enlarge the video image (4 steps). You can move through the zoomed picture using bBv V buttons.

To rotate picture

Press v / V during showing a picture to rotate the picture clockwise or counter clockwise.

JPEG disc compatibility with this player is limited as follows:

• Depending upon the size and number of JPEG files, it could take a long time for this unit to read the disc’s contents.If you do not see an on-screen display after several minutes, some of the files may be too large — reduce the resolution of the JPEG files to less than 5 million pixels and burn another disc.

• The total number of files in a folder should be less than 1190 files.

• Some discs may be incompatible due to a different recording format or the condition of disc.

• Ensure that all the selected files have the “.jpg” extensions when copying into the CD layout.

• If the files have “.jpe”or “.jpeg” extensions, please rename them as “.jpg” file.

• File names without “.jpg” extension will not be able to be read by this unit. Even though the files are shown as JPEG image files in Windows Explorer.

Still Picture

1. Press PAUSE/STEP during slide show. The player will now go into PAUSE mode.

2. To return to the slide show, press PLAY or press PAUSE/STEP again.

Page 34

Playing a DivX Movie file

Using this DVD Player you can play DivX file.

1. Insert a DivX file recorded media. The MOVIE menu appears on the TV screen.

MOVIE

0:00:00

List

Movie Folder 1 Movie Folder 2 Movie Folder 3 Movie Folder 4 Movie Folder 5 Movie Folder 6 Movie Folder 7 Movie Folder 8

2. Press v / V to select a folder, and press ENTER. A list of files in the folder appears.

3. If you want to view a particular file, press v / V to highlight a file and press ENTER or PLAY. You can use variable playback functions.Refer to page 29-30.

4. Press STOP to stop the playback.The Movie menu appears

Tips:

• If you are in a file list and want to return to the previ-

ous Folder list, use the v / V buttons on the remote to highlight and press ENTER.

• Press DISC MENU to move to the next page.

• On a CD with MP3/WMA, JPEG and MOVIE file, you

can switch MUSIC, PHOTO and MOVIE menu. Press TITLE and MUSIC, PHOTO and MOVIE word on top of the menu is highlighted.

• The picture may not displayed properly while DivX

playback.Set your TV system to AUTO or PAL-60 mode to restore the picture, if available.

• The disc subtitle may not be displayed properly, if a

DivX subtitle is downloaded through the internet.

• If the Disc Subtitle setup menu does not have the

DivX subtitle language you are going to play, the subtitle may not be displayed properly.

Notice for displaying the DivX subtitle

If the subtitle does not display properly during playback, press and hold SUBTITLE about 3 seconds then press b / B to select another language code until the subtitle is displayed properly.

DivX disc compatibility with this player is limited as follows:

•Available resolution size of the DivX file is under 720x576 (W x H) pixel.

• The file name of the DivX subtitle is available by 56 characters.

• If there is impossible code to express in the DivX file, it may be displayed as " _ " mark on the display.

• If the number of the screen frame is over 30 per 1 second, this unit may not operate normally.

•If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.

• If the file is recorded with GMC, the unit supports only 1-point of the record level.

GMC?

* GMC is the acronym for Global Motion

Compensation. It is an encoding tool specified in MPEG4 standard. Some MPEG4 encoders, like DivX or Xvid, have this option. There are different levels of GMC encoding, usually called 1-point, 2-point, or 3-point GMC.

Playable DivX file

.avi, .mpg, .mpeg

Playable Subtitle format

SubRip(*.srt/*.txt) SAMI(*.smi) SubStation Alpha(*.ssa/*.txt) MicroDVD(*.sub/*.txt) SubViewer 1.0(*.sub) SubViewer 2.0(*.sub/*.txt) TMPlayer(*.txt)

Playable Codec format

"DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx ", "XVID ", "MP43 ", "3IVX ".

Playable Audio format

"Dolby Digital ", "DTS ", "PCM ", "MP3 ", "WMA ".

• Sampling frequency: within 8 - 48 kHz (MP3), within 32 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3), 32 - 192kbps (WMA)

• Not all the WMA Audio format is compatible with this unit.

Operation

Page 35

Playing a DVD VR format Disc

DVD-VR

This unit will play DVD-R/RW discs recorded using the DVD-Video for mat that have been finalized using a DVD-recorder.

• This unit will play DVD-RW discs recorded using the Video Recording (VR) format.

1. Insert a disc and close the tray, It start playing automatically.

2. The DVD-VR menu appears on the TV screen when you press DISC MENU buttons while playing.

3. Press v / V to select a track then press PLAY or ENTER and playback starts.

4. Press DISC MENU to move to the list menu.

Note:

• Unfinalized DVD-R/RW discs cannot be played in this

player.

• Some DVD-VR disc are made with CPRM data by

DVD RECORDER.Player does not support these kinds of discs

What is ‘CPRM’?

CPRM is a copy protection system (with scramble system) only allowing the recording of ‘copy once’ broadcast programs.CPRM stands for Content Protection for Recordable Media. This player is CPRM compatible, which means that you can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings can only be played on players that are specifically compatible with CPRM.

Page 36

Additional Operation

Maintenance and Service

Refer to the information in this chapter before contacting a service technician.

Handling the Unit

When shipping the unit

Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.

Keeping the exterior surfaces clean

• Do not use volatile liquids such as insecticide spray near the unit.

• Do not leave rubber or plastic products in contact with the unit for a long period of time. since they leave marks on the surface.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution.

Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Operation

Maintaining the Unit

The DVD+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished.

Depending on the operating environment, regular inspection and maintenance are recommended after every 1,000 hours of use.

For details, please contact your nearest authorized service center.

Page 37

Language and Area Code List

Language Code List

Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.

Language Code

Abkhazian 6566 Afar 6565 Afrikaans 6570 Albanian 8381 Ameharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Aymara 6588 Azerbaijani 6590 Bashkir 6665 Basque 6985 Bengali; Bangla 6678 Bhutani 6890 Bihari 6672 Breton 6682 Bulgarian 6671 Burmese 7789 Byelorussian 6669 Cambodian 7577 Catalan 6765 Chinese 9072 Corsican 6779 Croatian 7282 Czech 6783 Danish 6865 Dutch 7876 English 6978 Esperanto 6979 Estonian 6984 Faroese 7079

Language Code

Fiji 7074 Finnish 7073 French 7082 Frisian 7089 Galician 7176 Georgian 7565 German 6869 Greek 6976 Greenlandic 7576 Guarani 7178 Gujarati 7185 Hausa 7265 Hebrew 7387 Hindi 7273 Hungarian 7285 Icelandic 7383 Indonesian 7378 Interlingua 7365 Irish 7165 Italian 7384 Japanese 7465 Javanese 7487 Kannada 7578 Kashmiri 7583 Kazakh 7575 Kirghiz 7589 Korean 7579 Kurdish 7585 Laothian 7679 Latin 7665 Latvian, Lettish 7686

Language Code

Lingala 7678 Lithuanian 7684 Macedonian 7775 Malagasy 7771 Malay 7783 Malayalam 7776 Maltese 7784 Maori 7773 Marathi 7782 Moldavian 7779 Mongolian 7778 Nauru 7865 Nepali 7869 Norwegian 7879 Oriya 7982 Panjabi 8065 Pashto, Pushto 8083 Persian 7065 Polish 8076 Portuguese 8084 Quechua 8185 Rhaeto-Romance 8277 Rumanian 8279 Russian 8285 Samoan 8377 Sanskrit 8365 Scots Gaelic 7168 Serbian 8382 Serbo-Croatian 8372 Shona 8378 Sindhi 8368

Language Code

Singhalese 8373 Slovak 8375 Slovenian 8376 Somali 8379 Spanish 6983 Sudanese 8385 Swahili 8387 Swedish 8386 Tagalog 8476 Tajik 8471 Tamil 8465 Tatar 8484 Telugu 8469 Thai 8472 Tibetan 6679 Tigrinya 8473 Tonga 8479 Turkish 8482 Turkmen 8475 Twi 8487 Ukrainian 8575 Urdu 8582 Uzbek 8590 Vietnamese 8673 Volapük 8679 Welsh 6789 Wolof 8779 Xhosa 8872 Yiddish 7473 Yoruba 8979 Zulu 9085

Area Code List

Choose a area code from this list.

Area Code

Afghanistan AF Argentina AR Australia AU Austria AT Belgium BE Bhutan BT Bolivia BO Brazil BR Cambodia KH Canada CA Chile CL China CN Colombia CO Congo CG Costa Rica CR Croatia HR Czech Republic CZ Denmark DK Ecuador EC Egypt EG El Salvador SV

Area Code

Ethiopia ET Fiji FJ Finland FI France FR Germany DE Great Britain GB Greece GR Greenland GL Islands HM Hong Kong HK Hungary HU India IN Indonesia ID Israel IL Italy IT Jamaica JM Japan JP Kenya KE Kuwait KW Libya L Y Luxembourg LU

Area Code

Malaysia MY Maldives MV Mexico MX Monaco MC Mongolia MN Morocco MA Nepal NP Netherlands NL Netherlands Antilles AN New Zealand NZ Nigeria NG Norway NO Oman OM Pakistan PK Panama PA Paraguay PY Philippines PH Poland PL Portugal PT Romania RO Russian Federation RU

Area Code

Saudi Arabia SA Senegal SN Singapore SG Slovak Republic SK Slovenia SI South Africa ZA South Korea KR Spain ES Sri Lanka LK Sweden SE Switzerland CH Taiwan TW Thailand TH Turkey TR Uganda UG Ukraine UA United States US Uruguay UY Uzbekistan UZ Vietnam VN Zimbabwe ZW

Page 38

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

Symptom

No power.

The power is on, but the DVD player does not work.

No picture.

No sound.

The picture is poor.

The DVD player does not start playback.

The remote control does not work properly.

Video tape cannot be inserted.

No Hi-Fi sound

No NICAM sound recording

Cause

 The power cord is disconnected.

 No disc is inser ted.

 The TV is not set to receive this unit’s

signal output.

 The video cable is not connected

securely.

 The Progressive Scan is set to “On” on

the setup menu but is connected to a standard (analog) television.

 The equipment connected with the

audio cable is not set to receive DVD signal output.

 The audio cables are not connected

securely.

 The power of the equipment connected

with the audio cable is turned off.

 The Audio option is set to the wrong

position.

 The disc is dir ty.  The TV channels are not tuned in properly.

 An unplayable disc is inserted.

 The disc is placed upside down.

 The disc is not placed within the guide.

 The disc is dir ty.  The Rating level is set.

 There is an obstacle in the path of the

remote control and this unit.

 The batteries in the remote control are

exhausted.

 Is the cassette compar tment empty?

 Audio mode is not set properly.

 NICAM mode is not set properly.

Correction

 Plug the power cord into the wall outlet

securely.

 Inser t a disc.

 Select the appropriate video input mode

on the TV so the picture from the this unit appears on the TV screen.

 Connect the video cable into the jacks

securely.

 Set Progressive Scan to “Off”

(see page 18).

 Select the correct input mode of the

audio receiver so you can listen to the sound from the this unit.

 Connect the audio cable into the jacks

securely.

 Turn on the equipment connected with

the audio cable.

 Set the Audio option to the correct posi-

tion, then turn on the DVD player again by pressing POWER.

 Clean the disc.  Check tuning, carry out tuning again.

 Inser t a playable disc. (Check the disc

type and Regional code.)

 Place the disc with the playback side

down.

 Place the disc on the disc tray correctly

inside the guide.

 Clean the disc.  Cancel the Rating function or change

the rating level.

 Remove the obstacle.

 Replace the batteries with new ones.

 Eject the tape in.

 Select “STEREO” by repeatedly pressing

“AUDIO” on the remote control.

 Make sure NICAM in the menu is set to

AUTO for the station to be recorded.

Reference

Page 39

Specification

General

Power requirements AC 220-240V, 50 Hz Power consumption 17W Dimensions (approx.) 430 x 78.5 x 265 mm (W x H x D) Mass (approx.) 4.2 kg Operating temperature 5˚C to 35˚C (41˚F to 95˚F) Operating humidity 5 % to 90 % Timer 24 hours display type RF Modulator UHF 22 - 68 (Adjustable)

System

Laser Semiconductor laser, wavelength 650 nm Video Head system Double azimuth 6 heads, helical scanning. Signal system PAL Frequency response DVD (PCM 96 kHz):8 Hz to 44 kHz

DVD (PCM 48 kHz):8 Hz to 22 kHz

CD: 8 Hz to 20 kHz Signal-to-noise ratio More than 100dB (ANALOG OUT connectors only) Harmonic distortion Less than 0.008% Dynamic range More than 100 dB (DVD)

More than 95 dB (CD)

Inputs (VCR)

Audio -6.0dBm, more than 10 kohms (SCART)

-6.0dBm, more than 47 kohms (RCA)

Video 1.0 Vp-p, 75 ohms, unbalanced (SCART/RCA)

Outputs (DVD)

VIDEO OUT 1 Vp-p 75 ohms, sync negative COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 Ω, negative sync, RCA jack x 1 (Progressive Scan) (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2

RGB output 0.7 Vp-p, 75 ohms Audio output (coaxial audio) 0.5 V (p-p), 75 Ω, RCA jack x 1 Audio output (analog audio) 2.0 Vr ms (1 KHz, 0 dB), 600 Ω, RCA jack (L, R)x2/SCART (TO TV)

Outputs (VCR)

Audio -6.0dBm, less than 1 kohms (SCART) Video 1.0Vp-p, 75 ohms, unbalanced (SCART)

RGB output 0.7 Vp-p, 75 ohms



Design and specifications are subject to change without notice.

P/NO : 3834RV0038U TARGA GmbH Lange Wende 41 59494 Soest Germany

www.targa-online.com

Targa DPV-5200 Series User's Manual And Service Information

Specifications and Main Features

Frequently Asked Questions

User Manual