Tapmatic B915848 User Manual

SAFETY DATA SHEET

www.lpslabs.com

1. Identification

Product identifier LPS® Tapmatic® Natural

Other means of identification

Part Number

Recommended use

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

Manufacturer

Company name
Address

Country

In Case of Emergency

Website
E-mail

44220, 44230, 44240

A general purpose, industrial cutting fluid designed for cutting and machining steel, aluminum and
other types of metals.

None known.

LPS Laboratories, a division of Illinois Tool Works, Inc.
4647 Hugh Howell Rd.
Tucker, GA 30084
(U.S.A.)
Tel: [phone]
1-800-424-9300 (inside U.S.)
+001 703-527-3887 (outside U.S.)

[e-mail]

2. Hazard(s) identification

Physical hazards

Health hazards

Environmental hazards

OSHA defined hazards

Label elements

Hazard symbol

Signal word

Hazard statement

Precautionary statement

Prevention

Response

Storage

Disposal

Hazard(s) not otherwise
classified (HNOC)

Supplemental information

Not classified.

Not classified.

Not classified.

Not classified.

None.

None.

The mixture does not meet the criteria for classification.

Observe good industrial hygiene practices.

Wash hands after handling.

Store away from incompatible materials.

Dispose of waste and residues in accordance with local authority requirements.

None known.

Not applicable.

3. Composition/information on ingredients

Mixtures

CAS number %Chemical name Common name and synonyms

67762-26-9Methyl Oleate

5 - < 10

4. First-aid measures

Inhalation

Skin contact

Eye contact

Ingestion

Most important
symptoms/effects, acute and
delayed

Material name: LPS® Tapmatic® Natural

747 Version #: 01 Issue date: 10-08-2013

If breathing is difficult, remove to fresh air and keep at rest in a position comfortable for breathing.
Call a physician if symptoms develop or persist.

Wash off with soap and water. Get medical attention if irritation develops and persists.

Any material that contacts the eye should be washed out immediately with water. If easy to do,
remove contact lenses. Continue rinsing. Get medical attention if irritation develops and persists.

Rinse mouth thoroughly. Get medical attention if symptoms occur. If ingestion of a large amount
does occur, call a poison control center immediately.

Direct contact with eyes may cause temporary irritation.

SDS US

1 / 6

Indication of immediate

waterways, sewer, basements or confined areas. Following product recovery, flush area with water

medical attention and special
treatment needed

General information

Provide general supportive measures and treat symptomatically.

Call a POISON CENTER or doctor/physician if you feel unwell.

5. Fire-fighting measures

Suitable extinguishing media

Unsuitable extinguishing
media

Specific hazards arising from
the chemical

Special protective equipment
and precautions for firefighters

Fire-fighting
equipment/instructions

Specific methods

General fire hazards

Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).

Do not use water jet as an extinguisher, as this will spread the fire.

No unusual fire or explosion hazards noted.

Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.

In case of fire and/or explosion do not breathe fumes. Cool containers exposed to heat with water
spray and remove container, if no risk is involved.

Move containers from fire area if you can do so without risk.

No unusual fire or explosion hazards noted.

6. Accidental release measures

Personal precautions,
protective equipment and
emergency procedures

Methods and materials for
containment and cleaning up

Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Do not touch damaged containers or spilled material unless wearing appropriate
protective clothing. Use personal protection recommended in Section 8 of the SDS.

Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Absorb in vermiculite, dry sand or earth and place into containers. Prevent entry into

.

Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to

remove residual contamination.

Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.

Environmental precautions

Avoid discharge into drains, water courses or onto the ground.

7. Handling and storage

Precautions for safe handling

Conditions for safe storage,
including any incompatibilities

Avoid contact with eyes. Do not get this material in contact with skin. Avoid prolonged exposure.

Store in original tightly closed container. Store away from incompatible materials (see Section 10
of the SDS).

8. Exposure controls/personal protection

Occupational exposure limits

Biological limit values

Appropriate engineering
controls

Individual protection measures, such as personal protective equipment

Eye/face protection

Skin protection

Hand protection

Other

Respiratory protection

Thermal hazards

General hygiene
considerations

No exposure limits noted for ingredient(s).

No biological exposure limits noted for the ingredient(s).

Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level.

Avoid contact with eyes. Wear safety glasses with side shields (or goggles). Eye wash fountain is
recommended.

For prolonged or repeated skin contact use suitable protective gloves. Chemical resistant gloves
are recommended.

Avoid contact with the skin. Wear suitable protective clothing and gloves. Chemical resistant
gloves.

Do not breathe dust/fume/gas/mist/vapors/spray. In case of insufficient ventilation, wear suitable
respiratory equipment.

None known.

Always observe good personal hygiene measures, such as washing after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants.

9. Physical and chemical properties

Appearance

Physical state

Form

Color

Material name: LPS® Tapmatic® Natural

747 Version #: 01 Issue date: 10-08-2013

Liquid.

Liquid.

Liquid.

Green

SDS US

2 / 6