Tapmatic B915847 User Manual

SAFETY DATA SHEET

www.lpslabs.com

1. Identification

Product identifier

Other means of identification

Part Number

Recommended use

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

Manufacturer

Company name
Address

Country

In Case of Emergency

Website
E-mail

Tapmatic® Edge Lube

43200

A metal-cutting fluid designed for cutting and forming applications.

None known.

LPS Laboratories, a division of Illinois Tool Works, Inc.
4647 Hugh Howell Rd.
Tucker, GA 30084
(U.S.A.)
Tel: [phone]
1-800-424-9300 (inside U.S.)
+001 703-527-3887 (outside U.S.)

[e-mail]

2. Hazard(s) identification

Physical hazards

Health hazards

OSHA defined hazards

Label elements

Hazard symbol

Signal word

Hazard statement

Precautionary statement

Prevention

Response

Storage

Disposal

Hazard(s) not otherwise
classified (HNOC)

Supplemental information

Not applicable.

Not classified.

Category 2BSerious eye damage/eye irritation

Not classified.

None.

Warning

Causes eye irritation.

Wash thoroughly after handling.

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present
and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.

Not assigned.

Not assigned.

Not classified.

3. Composition/information on ingredients

Mixtures

Non-hazardous components

CAS number

Alcohols, C10-16,ethoxylated

Other components below reportable levels 90 - 100

68002-97-1

%Chemical name Common name and synonyms

3 - < 5

4. First-aid measures

Inhalation

Skin contact

Eye contact

Ingestion

Material name: Tapmatic® Edge Lube

703 Version #: 01 Issue date: 08-05-2013

Under normal conditions of intended use, this material is not expected to be an inhalation hazard.
If inhaled, remove to fresh air. If breathing is difficult, give oxygen. If symptoms persist, get medical
attention.

Wash off immediately with plenty of water. Get medical attention if irritation develops and persists.

Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Get medical attention if irritation develops and persists.

In the unlikely event of swallowing contact a physician or poison control center.

SDS US

1 / 6

Most important

where possible). In case of shortness of breath, give oxygen. Keep victim under observation.

with water spray and remove container, if no risk is involved.

symptoms/effects, acute and
delayed

Indication of immediate
medical attention and special
treatment needed

General information

Irritant effects. Symptoms may include stinging, tearing, redness, swelling, and blurred vision.
Defatting of the skin. Rash.

Provide general supportive measures and treat symptomatically.

In the case of accident or if you feel unwell, seek medical advice immediately (show the label

5. Fire-fighting measures

Suitable extinguishing media

Unsuitable extinguishing
media

Specific hazards arising from
the chemical

Special protective equipment
and precautions for firefighters

Fire-fighting
equipment/instructions

Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).

None known.

During fire, gases hazardous to health may be formed.

Self-contained breathing apparatus and full protective clothing must be worn in case of fire.

Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA. Cool containers exposed to heat

6. Accidental release measures

Personal precautions,
protective equipment and
emergency procedures

Methods and materials for
containment and cleaning up

Environmental precautions

Keep unnecessary personnel away. Use personal protection recommended in Section 8 of the
SDS.

Stop the flow of material, if this is without risk. Following product recovery, flush area with water.
For waste disposal, see section 13 of the SDS.

Avoid discharge into drains, water courses or onto the ground.

7. Handling and storage

Precautions for safe handling

Conditions for safe storage,
including any incompatibilities

Do not handle, store or open near an open flame, sources of heat or sources of ignition. Protect
material from direct sunlight. Do not breathe dust/fume/gas/mist/vapors/spray. Do not get this
material in contact with eyes. Do not get this material in contact with skin. Avoid prolonged
exposure. Do not get this material on clothing. Do not use in areas without adequate ventilation.
Wear personal protective equipment. Observe good industrial hygiene practices. Wash thoroughly
after handling. Use care in handling/storage.

Keep tightly closed in a dry, cool and well-ventilated place. Keep out of the reach of children. Use
care in handling/storage.

8. Exposure controls/personal protection

Occupational exposure limits

Biological limit values

Appropriate engineering
controls

Individual protection measures, such as personal protective equipment

Eye/face protection

Skin protection

Hand protection

Other

Respiratory protection

Thermal hazards

General hygiene
considerations

No exposure limits noted for ingredient(s).

No biological exposure limits noted for the ingredient(s).

Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level.

If contact is likely, safety glasses with side shields are recommended. Eye wash fountain is
recommended.

For prolonged or repeated skin contact use suitable protective gloves. Chemical resistant gloves
are recommended.

Avoid contact with the skin. Avoid contact with clothing. Normal work clothing (long sleeved shirts
and long pants) is recommended. Chemical resistant gloves.

No personal respiratory protective equipment normally required.

None known.

Always observe good personal hygiene measures, such as washing after handling the material
and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants.

9. Physical and chemical properties

Appearance

Physical state

Material name: Tapmatic® Edge Lube

703 Version #: 01 Issue date: 08-05-2013

Solid.

Solid.

SDS US

2 / 6