Tap Magic 57040Q User Manual

Tap Magic Formula 1 Aqueous

SECTION 1: Identification of the substance/mixture and of the supplier

Product name:

Tap Magic Formula 1 Aqueous

Manufacturer/Supplier Article number:

50016Q, 50128Q, 50640Q, 53840Q, 57040Q

Special Notes on Product uses:

After use of this product, clean and lubricate metal surfaces to avoid

machining.**

Recommended uses of the product:

Machining, Cutting, Tapping, and Metal Processing.

Manufacturer/Supplier Details:

Email: [e-mail]

Emergency telephone number: ChemTel Inc.: [phone], [phone]

SECTION 2: Hazards identification

P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to d

Unknown Acute Toxicity: <0.2% ingredients are of unknown acute toxicity.

NFPA/HMIS

NFPA SCALE (0-4)

1

HMIS SCALE (0-4)

0

0

0

0

1

The Steco Corporation
2330 Cantrell Road
Little Rock, AR 72202 USA

Tel: [phone]
Website: www.tapmagic.com

Safety Data Sheet

staining and/or corrosion.

** Tap Magic Formula 1 Aqueous must not be use d for magnesium

Page 1 of 8

Classification of the substance or mixture:

GHS07: Irritant.

Skin2 H315, Eye2 H319

Signal word: Warning.
Hazard statements:

H315: Causes skin irritation.
H319: Causes serious eye irritation.

Precautionary statements:

P264: Wash hands and exposed skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.

P337+P313: If eye irritation persists get medical advice/attention.
P321: Specific treatment (see Section 4 on this SDS).
P362: Take off contaminated clothing and wash before reuse.
P302+P352: IF ON SKIN: Wash with soap and water.

Hazards Not Otherwise Classified (HNOC): None.

HEALTH

Health = 1

Fire = 0

Reactivit y = 0

0=Minimal Hazard; 1=Slight Hazard; 2=Moderate Hazard; 3=Serious Hazard; 4=Severe Hazard.

This SDS applies to part numbers: 50016Q, 50128Q, 50640Q, 53840Q, 57040Q

FIRE

PHYSICAL HAZARD

Physical Hazard = 0

Health = 1

Fire = 0

Safety Data Sheet

Tap Magic Formula 1 Aqueous

SECTION 3: Composition/information on ingredients

CAS / Identifying No.

Description

Wt. %

SECTION 4: First aid measures

Page 2 of 8

Chemical characterization: Mixture.
Description: Machining, cutting, tapping, and metal processing.
Hazardous components:

CAS: 39464-70-5

CAS: 102-71-6
The specific chemical identity has

been withheld as a trade secret.
CAS: 68551-13-3

Description of first aid measures

General information:

Take affected persons into fresh air, if feasible, or away from the source.
Consult a doctor/physician if concerned or feel unwell.
Immediately remove any clothing soiled by the product.
In case of irregular breathing or respiratory arrest, provide artificial respiration.

After inhalation:

Supply fresh air; consult doctor in case of complaints.
If aspirated, seek medical attention immediately.
Provide oxygen treatment if affected person has difficulty breathing.

After skin contact:

Immediately wash with water and soap and rinse thoroughly.
If skin irritation continues, consult a doctor.

After eye contact:

Remove contact lenses if worn.
Rinse opened eye for at least 15 - 20 minutes under running water. If symptoms persist, consult a doctor.

After swallowing:

Rinse out mouth and then drink plenty of water.
Call for medical help immediately.
Do not induce vomiting.
If victim vomits, be sure to keep head below knees to prevent aspiration of vomitus into lungs.
If victim is unconscious, position on their side and support them so they cannot roll onto their back.

Most important symptoms and effects, both acute and delayed:

Breathing difficulty.
Coughing.
Irritant to skin and mucous membranes.
Irritant effect on eyes.
Gastric or intestinal disorders when ingested.

Hazards:

Danger of impaired breathing.
May cause respiratory irritation.

Indication of any immediate medical attention and special treatment needed:

Consult a doctor/physician if concerned or feel unwell.

Polyethylene glycol phenyl ether phosphate

Eye1 H318; Skin 2 H315

Triethanolamine

Eye2 H319,

Amine complex trade secret

Sk1B H314; Acute tox 302, 312, 332, , STOT SE3 H335

Alcohols, C12-15, ethoxylated propoxylated

AcTox H302, H312, Eye2 H319; Aq AcTox1 H400

1 – 10%

1 – 10%

1%

1 – 10%

This SDS applies to part numbers: 50016Q, 50128Q, 50640Q, 53840Q, 57040Q

Safety Data Sheet

Tap Magic Formula 1 Aqueous

SECTION 5: Firefighting measures

SECTION 6: Accidental release measures

SECTION 7: Handling and storage

Page 3 of 8

Extinguishing media

Suitable extinguishing agents:

Use an extinguishing agent suitable for the surrounding fire.
Foam.
Carbon Dioxide.
Dry Chemical.

For safety reasons unsuitable extinguishing agents:
Special hazards arising from the substance or mixture: Carbon monoxide.

Advice for firefighters

Protective equipment:

Use self-contained breathing apparatus (SCBA) and full bunker turnout gear in a sustained fire.
Wear fully protective suit.

Hazardous Combustion Products:

Carbon oxides.
Nitrogen oxides.

Additional information:

Cool endangered receptacles with water fog or haze.
Use large quantities of foam as it is partially destroyed by the product.

None known.

Personal precautions, protective equipment and emergency procedures:

Use respiratory protective device against the effects of release.
Wear protective equipment.
Keep unprotected persons away.
Ensure adequate ventilatio n.
Particular danger of slipping on leaked/spilled product.

Environmental precautions:

For small spills, soak up with shop towels or absorbent material such as oil-dry or vermiculite.
For large spills, any leaks should be stopped.
Spill should be contained, then cleaned up using vacuum truck or absorbent material.

Methods and material for containment and cleaning up:

Absorb with non-combustible liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Pick up mechanically.
Send for recovery or disposal in suitable receptacles.
Dispose contaminated material as waste according to Section 13.

Reference to other sections:

See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.

Precautions for safe handling:

Prevent formation of aerosols.
Avoid splashes or spray in enclosed areas.
Use only in well ventilated areas.
Prevent from freezing.
**After use of this product, clean and lubricate metal surfaces to avoid staining and/or corrosion.

This SDS applies to part numbers: 50016Q, 50128Q, 50640Q, 53840Q, 57040Q