Tapfer 1005BTF, 1006BTF User guide

Operating instructions

Portable charger 10050 Type C - Model No. 1005BTF 20100 Type C - Model No. 1006BTF

Item No. and Model No. 1005BTF / 1006BTF

Intended use

The product serves as a spare battery for mobile devices (for example, smartphone, tablet) with 5 V/DC voltage. The charger has USB Type-C™ and USB-A outputs that can be used to charge suitable products. The USB Type-C™ port and the Micro USB input are used to charge the internal battery. To charge the product, a USB charger (not included) is required. The product has a battery level indicator and is protected against overcharging and short circuit.

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged.

In addition, improper use can cause hazards such as short circuiting, re, electric shock etc.

Read the instructions carefully and keep them. Make this product available to third parties only together with its operating instructions.

Delivery content

• Portable charger

• USB charging cable (Micro USB to USB-A)

• Operating instructions

• Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

• Never use the product immediately after it has been brought from a cold room into a warm one. The condensation generated could destroy the product. Allow the device to reach room temperature before connecting and using it. This may take several hours.

• Never operate the product unattended.

• The housing heats up during operation. Ensure sufcient ventilation. The housing must not be covered!

• Do not short-circuit the USB connectors.

• Do not charge the product from a USB port of a computer or other products since

the power provided is insufcient. This can cause damage to the connected

product.

• Consult an expert when in doubt about operation, safety or connection of the device.

• Maintenance, modications and repairs are to be performed exclusively by an

expert or at a qualied shop.

• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

b) Rechargeable batteries

• The rechargeable battery is permanently built into the product and cannot be replaced.

• Never damage the rechargeable battery. Damaging the casing of the rechargeable

battery might cause an explosion or a re!

• Never short-circuit the contacts of the rechargeable battery. Do not throw the

battery or the product into re. There is a danger of re and explosion!

• Charge the rechargeable battery regularly, even if you do are not using the product. Due to the rechargeable battery technology being used, you do not need

to discharge the rechargeable battery rst.

• Never charge the rechargeable battery of the product unattended.

• When charging, place the product on a surface that is not heat-sensitive. It is normal that a certain amount of heat is generated during charging.

Latest operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when there is a potential risk of

personal injury, such as electric shock.

An exclamation mark in a triangle indicates important instructions in this operating

manual that absolutely have to be observed.

The arrow symbol indicates specic tips and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/ guarantee.

a) General

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

• Also observe the safety and operating instructions of any other devices which are connected to the product.

• When setting up the product, make sure that the cable is not pinched, kinked or damaged by sharp edges.

Operating elements

1 Function button

2 Micro USB input

3 USB Type-C™ input/output

4 USB-A output

5 Battery level indicator

Item No. / Model 1006BTF has 2 USB-A outputs.

1 432 5

Operation

Check the internal battery charge level before each use. Make sure the connection values of your mobile device match those of the product (see technical data). The USB cable is not suitable for data transfer.

Remove any protective lms from the product.

a) LED indicator of the battery charge level

Press the function button (1) once briey to check the battery level. The remaining capacity on the battery level indicator (5) is displayed as a percentage:

b) Charging the battery

• When using for the rst time, it is recommended to fully charge the product once.

• Charge the portable charger at the latest when the battery level falls below 25%.

• The portable charger is charged via the Micro USB input (2) or the USB Type-C™ input/ output (3). To charge the portable charger, a USB charger (not included) is required. A Micro USB charging cable for connection to the Micro USB input is included.

• Connect the Micro USB connector to the Micro USB input. Plug the USB-A connector of the USB charging cable into a USB-A port of a USB charger. Observe the technical data.

A USB charger with 2 A (Micro USB input) or 3 A (USB Type-C™ port) is recommended for the portable charger input current. If a lower input current is used, charging will take longer. However, an input current higher than 2 A (Micro USB) or 3 A (USB Type-C™) will not reduce the charging time since the input current is limited at the respective ports.

• With a remaining battery capacity of approx. 20 %, the portable charger can have the following charging times:

With 2 A USB charger via the Micro USB input

- Item No. / Model 1005BTF (10050 mAh): up to approx. 8 hours

- Item No. / Model 1006BTF (20100 mAh): up to approx. 12 hours

With 3 A USB charger via the USB Type-C™ input

- Item No. / Model 1005BTF (10050 mAh): up to approx. 6 hours

- Item No. / Model 1006BTF (20100 mAh): up to approx. 9 hours

• Check the model you have purchased. While charging, the current battery level will be

indicated by a percentage ashing on the display.

• Once the battery is fully charged, the battery level indicator will be lit steadily.

• Disconnect the connected cables. The battery level indicator will go off after approx. 10 seconds.

c) Charging a mobile device

• You can charge the portable charger and your mobile devices at the same time.

It is not recommended to charge the portable charger and connected mobile devices at the same time as the battery of the portable charger will be constantly discharging in this case. Accordingly, it takes longer to charge the internal battery of the portable charger.

• Connect the USB-A connector of the USB charging cable to the USB-A output (4). If your mobile device has a USB Type-C™ port, you can use the USB Type-C™ connector (not included) to plug a charging cable into the USB Type-C™ input/output (3). Products with a USB Type-C™ port normally enable a higher charging current and can therefore be charged faster than those with a Micro USB port.

The maximum charging current (3 A) is distributed to the USB outputs when both outputs are used. Therefore, take note of the amount of charging current required by your mobile device.

• While charging, the battery level of the portable charger will be indicated by the steadily lit remaining capacity.

• Disconnect the USB charging cable from the connected product and the portable charger to stop or interrupt charging. The battery level indicator will go off after approx. 10 seconds.

Care and cleaning

• Disconnect the product from connected products and from the power supply before every cleaning.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunctioning.

• Clean the product with a dry, bre-free cloth.

• When cleaning, be sure to avoid contact with water or other liquids.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product according to the relevant statutory regulations.

You thus full your statutory obligations and contribute to the protection of the

environment.

Technical data

Input voltage/current ..................... Micro USB input 5 V/DC, 2 A

USB Type-C™ input 5 V/DC, 3 A

Output voltage/current .................. USB-A output 5 V/DC, max. 2.4 A

USB Type-C™ output 5 V/DC, max. 3 A All USB outputs combined max. 3 A

Operating conditions ..................... 0 to +35 °C, <75 % RH

Storage conditions ........................ 0 to +35 °C, <75 % RH

Item No. / Model No. 1005BTF

Internal battery .............................. Li-Ion / 10050 mAh

Dimensions (L x W x H) ................ 115 x 63 x 22 mm

Weight .......................................... 194 g

Item No. / Model No. 1006BTF

Internal battery .............................. Li-Ion / 20100 mAh

Dimensions (L x W x H) ................ 160 x 81 x 22 mm

Weight .......................................... 364 g

Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau

These operating instructions are a publication by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.

Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require

the prior written approval by the editor. Reprinting, also in part, is prohibited. These operating instructions represent the technical status at the time of printing.