Tansun SH2-1200W UK, SH2-1200W EU, SH3-1800W UK, SH3-1800W EU, SH4-2400W UK Reference Manual

The use of this symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about
recycling of this product, please contact your local council, your
household waste disposal service or the shop where you purchased the
product.

©Tansun Limited 2013 Part No. 043103 Issue. A

F o l l ow i n g i n f o r m a t i o n i s o n l y f o r E U - m e m be r s t a te s :

M a i n t e n a n c e

In the event of heater failure, or for spare parts or advice, please contact the
manufacturer or your service agent.

•

Disconnect from the mains by removing the plug from the main sockets before
commencing any maintenance procedure including cleaning.

•

To ensure optimum heat effectiveness, it is recommended that that the guards are
removed and the reflectors are wiped with a lint-free cloth should the reflectors
show considerable signs of dust or dirt.

EUROPEAN & UK MODEL HEATERS

Spectrum House, Unit 1, Ridgacre Road, West Bromwich,

West Midlands, B71 1BW, England.

Tel: [phone] - Fax: [phone]

Email: [e-mail] - Website: www.tansun.com

TRIPLE: SH3-1800W UK, SH3-1800W EU

DOUBLE: SH2-1200W UK, SH2-1200W EU

QUADRUPLE: SH4-2400W UK, SH4-2400W EU

Reference Manual

2

Ca ut io n

When using Tansun electrical heaters, basic precautions should always be
followed to reduce the risk of fire, electric shock, and injury to persons,
including the following:

Read all instructions before using this heater.

•

Before using this appliance:

- Check that the voltage indicated on the type plate corresponds to the
mains supply voltage.

- Ensure that the heater has been securely fastened in it

s final mounting

position.

•

Do not locate the heater immediately below a socket outlet.

•

This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

un

derstand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by
children without supervision.

•

Children of less than 3 years should be kept away unless continually
supervised.

•

Children aged from 3 years and less than 8 years shall only switch on/
off the appliance provided that it has been placed or installed in its
in

tended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.

•

CAUTION—Some parts of the product can become very hot and
cause burns. Particular attention has been given where children
and vulnerable people are present.

•

Remove the plug from the mains socket (or disconnect pole switch)
during installation, cleaning and/or replacing the element and always
ensure that the element is cool.

Fig. E

0.5m MINIMUM TO CEILING

Chain Hanging - All Models

•

The Eclipse heaters can be chain hung from a ceil­ing.

•

When ceiling hanging the Eclipse heater, ensure the
minimum distance from the ceiling is adhered to as
shown in Fig. E. and maintain the minimum distance
to the floor.

•

Please refer to Table 1 for the recommended
positioning of the heater with regards to minimum
distances. Do not install the heater in a corner!

•

Always allow the heater to cool before attempting to
reposition/move. Never attempt to move the heater
while it is switched on!

•

Observe the minimum safe distance between the
heater body and inflammable surfaces and objects
when mounting.

•

Keep out of the reach of children.

1. Please refer to Table 1 for recommended positioning
of the heater. When hanging from a ceiling, two
chains of equal length and gauge are required and
should be used with fixings that are adequate to
hold the weight of the heater. If in doubt contact a
professional for advice!

2. Attach the heater assembly to the chains via the hole
in the centre of the middle bracket (remove the
L-shaped wall brackets) as shown in Fig. E. and
ensure the heater faces directly down when hanging.

3. Arrange the mains supply cord so it cannot be tripped

over or damaged and ensure it is not resting on the
heater body or mounting brackets. Also ensure it is
away from the front of the heater.

Always isolate the heater from the mains supply
when adjusting the position.

2.0m MIN. HEIGHT FROM FLOOR

GROUND LEVEL

7

Fig. B

DRILLING HOLE TEMPLATE DIMENSIONS FOR

WALL MOUNTED BRACKETS - DOUBLE HEATER

Fig. C

Fig. D

DRILLING HOLE TEMPLATE DIMENSIONS FOR

WALL MOUNTED BRACKETS - TRIPLE HEATER

DRILLING HOLE TEMPLATE DIMENSIONS FOR

WALL MOUNTED BRACKETS - QUADRUPLE HEATER

1. Securely fasten the Eclipse brackets to the mounting surface using the fixing holes
in the brackets. See Fig.s B, C and D for mounting hole centres of the brackets.
Please refer to Table 1 for recommended positioning of the heater.

2. Fix in the required angular position by tightening the fixing bolts on the brackets at
the rear of the heater.

3. Arrange the mains supply cord so it cannot be tripped over or damaged and ensure
it is not resting on the heater body or mounting brackets. Also ensure it is away from
the front of the heater.

Always isolate the heater from the mains supply when adjusting the angular
position.

6

•

Do not use an extension cord with this product because the extension
cord may overheat and cause a risk of fire.

•

Keep the mains supply cord away from the body of the heater which will
get hot during use.

•

Arrange the mains supply cord so it cannot be tripped over or damaged.

•

Do not cover or obstruct the heater while it is in use.

•

Do not insert any object through any slot or opening in the heater.

•

Do not use if a guard is not present.

•

Do not install less than the minimum mounting distance from the floor.

•

WARNING: This heater is not equipped with a device to control the

room temperature. Do not use this heater in small rooms when they are

occupied by persons not capable of leaving the room on their own,
unless constant supervision is provided.

•

Do not use the heater in a bathroom.

•

WARNING: This appliance must be connected to a supply that is
earthed!

I M P O R T A N T -
S AV E T H E S E I NS T R U C T I O N S F O R F U T U R E R EF E R E N C E

Ri sk o f F i r e

Keep combustible materials such as furniture, papers, clothes and curtains
at least 1.8m (6 feet) from the front of the heater and away from the sides

and rear. If the heater is to be used outside, we recommend that a

waterproof or indoor socket outlet is used.

3

I n t r o d u c t i o n

The Tansun range of Eclipse heaters contain long-life ceramic elements which are
highly efficient and durable. The heaters are mounted on adjustable brackets that
allows the heat to be directed exactly where it is required. Its attractive design means
that it is effective yet unobtrusive. The Eclipse heaters are designed for indoor and
outdoor use and is therefore weatherproof.

Please read the caution notes and following instructions carefully before use.
The safety of this heater is guaranteed only by its correct usage in accordance
with these instructions, therefore it is recommended that they are retained for
future reference.

Sp e ci f i c a t i o n

Ta bl e 1. U K an d E ur op ea n He at er s

Use an MCB Type 3 or C.

Model

SH2-1200W SH3-1800W SH4-2400W

Description

Double Triple Quadruple

Voltage (V)

230 230 230

No. of Elements x
Power (W)

2 x 600 3 x 600 4 x 600

Total Power (kW)

1.2 1.8 2.4

Total Current (A)

5.2 7.8 10.4

Min. height from
floor (m)

2.0 2.0 2.0

Min. distance from
ceiling (m)

0.3 0.3 0.3

Min. distance from
side wall (m)

0.5 0.5 0.5

Dimensions (depth
inc. bracket in max.
pos.) L x H x D (mm)

940 x 111 x 169 1300 x 111 x 169 1660 x 111 x 169

Weight (kg)

5.2 7.1 8.9

Ingress
Protection (IP)

IPx4 IPx4 IPx4

4

I n s t a l l a t i o n

•

Warning - this appliance must be connected to an earthed supply.

•

All version are fitted with 3.0 metres of mains supply cord and a moulded plug,
therefore it is unnecessary to remove the terminal box in order to carry out
normal installation of these models.

Wa l l M o u n t i n g

•

The Eclipse heater should be
mounted in a horizontal manner only
(see Fig. A ).

•

Do not position the heater at an
angle more than 70° and less than
45° from the mounting surface as
shown in Fig. A.

•

Always allow the heater to cool
before attempting to reposition/move.
Never attempt to move the heater
while it is switched on!

•

Observe the minimum safe distance
between the heater body and
inflammable surfaces and objects
when mounting.

•

Please refer to Table 1 for the
recommended positioning of the
heater. Do not install the heater in a
corner!

•

Do not mount the heater on plastic
soffits and fascia boards and ensure
the mounting surface will suitably
withstand the radiant heat from the
heater body.

5

I n s t a l l a t i o n c o n t i n u e d . . .

•

All installations must be in accordance with the latest I.E.E. safety regulations or
equivalent.

•

We recommend using a RCD where applicable.

•

If the supply cord becomes damaged, it must be replaced by the manufacturer,
its service agent or a similar qualified person in order to avoid a hazard.

•

Please observe the minimum safe distance between the heater body and any
inflammable surfaces.

•

If in any doubt, please contact a suitably qualified electrician.

•

To disconnect heater, remove the mains plug from the socket outlet.

Max. 70°

Min. 45°

2.0m MIN. HEIGHT FROM FLOOR

GROUND LEVEL

Fig. A

Continued on next page...