Tannoy SYSTEM 600A User Manual

System 600a

USER MANUAL

Contents

INTRODUCTION 1

OPERATING INSTRUCTIONS 1

Unpacking and visual checks 1
Preliminary recommendation 1
Installing and connecting the system 2
Controls and indicators 3
Use close to TV screens and video monitors 3

SYSTEM DESCRIPTION AND PHILOSOPHY 4

Drive unit. 4
Cabinet 4
Active crossover and amplifier 5

SERVICING

Cabinet finish 6
Dual Concentric driver removal 6
Drive unit servicing 6
Checking the unit 6
Amplifier 6
List of spare parts 7
Warranty 7

CURVES 8

TECHNICAL SPECIFICATIONS 9

System 9
Electronic section 9
Cabinet 9

Declaration of Conformity 10

INTRODUCTION

Thank you for purchasing the Tannoy System 600A Active Monitor.
The System 600A is a very compact, active near-field reference monitor. Using an

advanced Dual Concentric 6.5” driver, it offers the advantages of point source operation
in a cost-effective design, combined with the benefits of active speaker technology: a
highly optimised active crossover section; ideal matching between amplifiers and
transducers; higher output for lower distortion. Active user controls are also provided to
allow further bass extension (LF contour) and greater flexibility. The attractive octagonal
shape of the cabinet, with its original rounded edge front panel also contributes to the
excellent acoustic performance of the system.

Designed to be located on top of the mixing console, in a landscape format, it will
equally suit other situations where it can be used in portrait mode without any drawback,
thanks to its point source operation.

This manual is intended to provide the user with some useful advice on how to install
and use the loudspeakers, as well as more technical information about how the system
is designed, and its detailed specifications. Our goal is to help you get the best results
from this monitoring system.

OPERATING INSTRUCTIONS

Unpacking and visual checks

The System 600A are packed in pairs. To get the speakers out of the carton without
damage open the end flaps fully and bend them right back . Remove the upper cushion,
then lift each loudspeaker out carefully.

Inspect the speakers for signs of transit damage. In the unlikely event of this having
occurred inform the carrier and the supplier. Keep all the packaging if damage has
occurred as this will show evidence of any excessive handling forces. It is also a good
idea to keep the carton for future transportation.

Preliminary recommendation

Initially we would like to give you a word of warning about the high sound pressure
levels which these speakers are capable of generating. Over a sustained period of time
levels over 95 dB for 8 hours per day will eventually cause permanent hearing loss.
Because Tannoy monitors have very low levels of time, amplitude and frequency
distortion it is not always obvious that the sound pressure level is high whilst working
with them.

For continuous exposure we recommend the occasional use of a sound level meter
capable of integrating the sound level over a period of exposure according to noise
control standards. This should be used just to check that noise levels are always within
safe limits.

Installing and connecting the system.

The compact, integrated design of a self-powered unit like the System 600A makes it
particularly easy to install.

After having unpacked the unit, first check that the operating voltage is properly set
(rear panel, location 1 in figure 1), and if it is not adjust the selector to the appropriate
position. Also check and if necessary replace the fuse (location 3), as its rating should
match the operating voltage.

When choosing a suitable location for the monitors, bear in mind that the physical
mounting of loudspeakers can have a large influence on performance. For best results

the monitors should be mounted on a rigid structure, preferably with the use of soft pads
(rubber, Sorbothane, Blu-Tak etc..).

When used in the landscape orientation, we recommend location of the monitors so that
the drive units are toed inwards, with their axes oriented towards the listening position.
The distance between the two speakers should be about 1.5 to 2 metres, depending on
the monitoring position. The distance between the monitoring position and each speaker
should be slightly greater than the distance between the speakers. If the speakers are
placed too close to each other the full stereo image may not develop, on the other hand
if you place them too far apart you will notice an audible hole in the middle of the stereo
image.

Ensure that the console position does not obscure the direct sound radiation from the
Dual Concentric drive unit when sitting down. The engineer and producer should have a
clear, uninterrupted view of the monitor loudspeakers.

Having chosen an appropriate location for your monitors and arranged them
accordingly, connect the power cord to the mains socket and turn the power on (mains
switch, location 2 in figure 1). The blue LED on the front panel should now be
illuminated. Before connecting the source to the monitor, it is advisable to ensure that
there is no signal present (by setting the output faders) so that the signal is not likely to
overload the system.

Connect the audio signal source (console output) to the input connector (combined
XLR/jack socket) at the back of the monitor (location 4 in figure 1).

Figure 1. System 600A - Rear view

As indicated on the silk screen printing, the input connector is wired to the balanced
input as indicated below :

XLR input Jack input

Signal (+) pin 2 Tip (T)
Signal (-) pin 3 Ring (R)
Ground pin 1 Screen (S)