the evolution revealed
TS12
500W RMS
26Hz(-6dB)
15Hz
2 x line level phone
2 x XLR balanced
2 x XLR balanced
(direct or 80Hz high pass)
2nd order low pass,
50Hz - 150Hz, -6dB
After approximately 12 mins.
in absence of input signal
300mm (12“)
Closed box
22 litre / 0.78cu.ft
Phase control
Crossover defeat switch for
LFE operation
Soft limiting to avoid overload
LF extension control
372 x 335 x 335mm
5
14
/8 x 131/8 x 131/8”
12.5kg / 27.5 lbs
120V nominal AC~60Hz
230V nominal AC~50Hz
120V - T5AL / 250V
230V - T2.5AL / 250V
600VA
Features
Rigid cabinet, down-firing driver
BASH® digital power amplifier
Stereo line level inputs
XLR input and output
Direct or switched 80Hz high pass
Auto power on and sleep function
Soft-clip limiting
Gain and phase controls
&
&
&
PERFORMANCE TS8 TS10
Output power 200W RMS 300W RMS
Low frequency response 32Hz(-6dB) 29Hz(-6dB)
Limit for usable output 18Hz 16Hz
Inputs 2 x line level phone 2 x line level phone
Outputs 2 x XLR balanced 2 x XLR balanced
Input filter 2nd order low pass, 2nd order low pass,
Auto mute After approximately 12 mins. After approximately 12 mins.
Driver type 200mm (8”) 250mm (10”)
Enclosure type Closed box Closed box
Enclosure volume 12.5 litre / 0.45cu.ft 16.75 litre / 0.6cu.ft
Additional features Phase control Phase control
Enclosure (HxWxD)
- including feet 292 x 280 x 255mm 323 x 286 x 286mm
Enclosure weight 7.0kg / 15.4 lbs 9.5kg / 21 lbs
Mains voltage 120V nominal AC~60Hz 120V nominal AC~60Hz
&
2 x XLR balanced 2 x XLR balanced
(direct or 80Hz high pass) (direct or 80Hz high pass)
50Hz - 150Hz, -6dB 50Hz - 150Hz, -6dB
in absence of input signal in absence of input signal
Crossover defeat switch for Crossover defeat switch for
LFE operation LFE operation
Soft limiting to avoid overload Soft limiting to avoid overload
LF extension control LF extension control
1
11
/2 x 111/2 x 10” 121/16 x 115/16 x 115/16”
Mains fuse 120V - T2AL / 250V 120V - T3. 15AL / 250V
Maximum power
consumption 275VA 416VA
TS8, TS10 & TS12 Professional Active Subwoofers
Three powerful active subwoofers have been designed to complement the Reveal range of studio
monitors for 2.1, 5.1, 7.2 configurations or in any other multi channel combination required. All are
substantially constructed closed box cabinets with high power handling and long throw drive units
delivering tightly controlled bass with massive impact; ensuring that the punch and drive of the mix track
is faithfully reproduced.
230V nominal AC~50Hz 230V nominal AC~50Hz
230V - T1AL / 250V 230V - T1.6AL / 250V
Reveal 66
Reveal 66
Frequency response
(1) 60Hz-51kHZ
Recommended Amplifier Power 80 to 150W @ 8W
Power Handling Average RMS 80W
Normal Impedance 6
Sensitivity (3) 92dB for 1W at 1m
Distortion <0.6%
Crossover Frequency 2.7kHz
Dispersion (@-6dB) 90 degrees
DRIVE UNITS
Drive Units - LF/MID 2 x 165mm (6
1
/2”) multi fibre
paper pulp cone
WideBand™ HF 25mm (1”) titanium dome
neodymium magnet system
Cabinet
Type Optimised bass-reflex loaded
Construction MDF cabinet and front baffle.
Tongue and groove front and back
Finish Grey cabinet
Maroon painted baffle
Passive centre channel
reference monitor
Optimised bass-reflex loaded
cabinet with 40mm thick front
baffle
Two shielded 165mm (61/2”)
woofers, multi fibre paper pulp
cones
Shielded 25mm (1”) titanium
dome neodymium tweeter
WideBand™ HF extended to
51kHz corrects phase response
Whether you’re mixing for film, video
or 5.1 audio formats, a dedicated
centre-channel is a must.
The Reveal 66 is designed to fit into
your production environment with
minimal visual obstruction while
delivering the kind of performance
demanded of a centre-channel
speaker.
Wide dynamic range, equal capability
with vocal and music tracks and
more than enough acoustic output
make the Reveal 66 the perfect
centre channel in any Reveal
system.
Reveal 6
Frequency response
(1) 63Hz-51kHZ
Recommended Amplifier Power 50 to 100W @ 8W
Power Handling Average RMS 50W
Normal Impedance 6
Sensitivity (3) 90dB for 1W at 1m
Distortion <0.6%
Crossover Frequency 2.9kHz
Dispersion (@-6dB) 90 degrees
DRIVE UNITS
1
Drive Units - LF/MID 165mm (6
/2”) multi fibre
paper pulp cone
WideBand™ HF 25mm (1”) titanium dome
neodymium magnet system
Cabinet
Type Optimised bass-reflex loaded
Construction MDF cabinet and front baffle.
Tongue and groove front and back
Finish Grey cabinet
Maroon painted baffle
Reveal 6
Passive nearfield reference monitor
Optimised bass-reflex loaded cabinet with 40mm thick front baffle
Shielded 165mm (61/2”) woofer, multi fibre paper pulp cone
Shielded 25mm (1”) titanium dome neodymium tweeter
WideBand™ HF extended to 51kHz corrects phase response
The Reveal 6 combines all the heritage and purity of the original Reveal series
with the very latest in technology. The result is a no-nonsense nearfield
reference monitor with deep, punchy bass, clean and open mid-range
and unrivalled vocal intelligibility. Combine the Reveal 6 with your
preferred power amplifier and hear just how good a passive reference
monitor can sound.
Just because a speaker sounds great in one room doesn’t mean it will sound great in your studio.
Room acoustics, speaker placement and monitoring distance play a great role in the way a speaker
sounds. Until now there wasn’t much you could do about that without spending more money on
expensive equalisers and a professional acoustician to place the speakers and tune them to the room.
Tannoy’s exclusive Activ-Assist™ technology ensures that the great-sounding monitors we build will
sound great where it matters; right there in your studio! It all starts with Activ-Assist™ software running
on a PC/MAC with a sound card. The program automates the acoustic measurement process and
allows you to measure the speakers in the room like a pro.
Once the measurement is made the software calculates the right settings from over 2,000 potential
choices. Tuning the speaker is as simple as setting the switches on the rear panel to match the graphic
on the computer screen. In seconds your Reveal D monitors have been tuned and optimised for the
room with the same degree of precision that is used in some of the world’s best recording studios.
Activ-Assist™ software is available at no charge from www.tannoy.com for use with your own
measurement microphone. A calibrated Tannoy measurement microphone is also available as an
accessory from your local Tannoy dealer.
Automated speaker measurement system for Reveal D studio monitors
Recommends speaker EQ settings from 2,000 options
Performs dual-channel FFT measurements of great precision
Fool-proof on screen wizard-driven design
Free software works with all Reveal D-series models
Trim/Gain control
(on SPDIF input - post DAC)
over -10dB /- 4dBu range.
Ref: 0dBu (0.775V)
input for full rated output
RCA input for SPDIF with
75 Ohm terminating impedance
2nd RCA for SPDIF output
for slaving a stereo pair
XLR / 1/2”
jack combination
connector for
balanced input
Digital input
on / off
3-way switch
(post 2 channel DAC)
selects SPDIF stream
channel to be decoded
- Left/Right/Mono
Switch selection of
12dB/8ve 80Hz high
pass filter for use with
AV subwoofers
10 Activ-Assist™
DIP switches control
LF alignment mid/near/close field
& half/quarter/eighth
space compensation
10 Activ-Assist™
DIP switches
control mid band
and HF shelving trim
DIP switch ‘flat’
setting shown on
the back
panel artwork
SPEC NOTES : (1) +/- 3 dB, measured at 1m in an anechoic chamber.
Applications:
(2) Peak SPL at mix position for 1 pair driven
(3) Average over specified bandwidth for half space environment
Home studios/composition
Project studios, users of PC/MAC
DAW’s
Professional recording, broadcast,
post production studios & editing suites
PERFORMANCE 66D
Frequency response
Max SPL
(2) 117dB
(1) 49Hz-51kHZ
Distortion <0.4%
Dispersion @-6dB, 10kHz, horizontal 90 degrees
DRIVE UNITS
Drive Units – LF/MID 2 x 165mm (61/2”) multi fibre
paper pulp cone
WideBand
TM
HF 25mm (1”) titanium dome,
neodymium magnet system.
ELECTRONIC SYSTEM
Inputs 600
balanced XLR/Jack,
SPDIF RCA
SPDIF sampling rate 44.1 – 96kHz
Input Sensitivity (0dBu = 0.775mV) -10dBu to +4dBu
for a max SPL of 117dB
Amplifier output power 100W LF / 50W HF
Outputs SPDIF slave out RCA
User Controls Front panel mounted
on/standby/mute switch,
multi-function LED,
Rear panel mounted trim +6/-12dB,
80Hz high pass switch for AV use,
16-way Activ-Assist
TM
switch array
Reveal 66D
Active centre channel reference
monitor with Active-Assist™
Optimised bass-reflex loaded
cabinet with 40mm thick front
baffle
Two shielded 165mm (61/2”)
woofers, multi fibre paper
pulp cones
Shielded 25mm (1”) titanium
dome neodymium tweeter
WideBand
TM
HF extended to
51kHz corrects phase response
Active bi-amplification
(100W LF / 50W HF)
Putting together an active surround
system? Look no further than the
Reveal 66D as the ideal centre
channel monitor.
With its extended WideBand™
response, the R66D preserves the
harmonic structure of recorded music
and vocals; this results in a more
natural and accurate reproduction
of the original source. Ready to
integrate with your analogue or digital
production environment the R66D
includes Tannoy’s Activ-Assist™
equalisation technology.
PERFORMANCE 8D
Frequency response
Max SPL
(2) 118dB
(1) 46Hz-51kHz
Distortion <0.4%
Dispersion @-6dB, 10kHz, horizontal 90 degrees
DRIVE UNITS
Drive Units – LF/MID 200mm (8”) multi fibre
paper pulp cone
TM
WideBand
HF 25mm (1”) titanium dome,
neodymium magnet system.
ELECTRONIC SYSTEM
Inputs 600
balanced XLR/Jack,
SPDIF RCA
SPDIF sampling rate 44.1 – 96kHz
Input Sensitivity (0dBu = 0.775mV) -10dBu to +4dBu
for a max SPL of 118dB
Amplifier output power 120W LF / 60W HF
Outputs SPDIF slave out RCA
User Controls Front panel mounted
on/standby/mute switch,
multi-function LED,
Rear panel mounted trim +6/-12dB,
80Hz high pass switch for AV use,
16-way Activ-Assist
TM
switch array
Reveal 8D
High power active near field reference monitor with Activ-Assist™
Optimised bass-reflex loaded cabinet with 40mm thick front baffle
Shielded 200mm (8”) multi fibre paper pulp cone woofer
Shielded 25mm (1”) titanium dome neodymium tweeter
WideBand
TM
HF extended to 51kHz corrects phase response
Active bi-amplification (120W LF / 60W HF)
Tannoy Activ-Assist™ set-up software enabled
Get the big, deep low-frequency performance of an 200mm (8”) woofer with
the same purity and articulation of the rest of the Reveal range with the
R8D. Combining 180 Watts of bi-amplification, with Activ-Assist™
equalisation technology and an SPDIF digital input, the R8D is ready
for the most demanding applications. Classic Reveal performance
with extended LF response and up to 118dB of power output
makes the R8D the new standard for world-class nearfield
monitoring applications.
PERFORMANCE 6D
Frequency response
Max SPL
(2) 115dB
(1) 60Hz-51kHZ
Distortion <0.5%
Dispersion @-6dB, 10kHz, horizontal 90 degrees
DRIVE UNITS
1
Drive Units – LF/MID 165mm (6
/2”) multi fibre
paper pulp cone
TM
WideBand
HF 25mm (1”) titanium dome,
neodymium magnet system.
ELECTRONIC SYSTEM
Inputs 600
Frequency response (1) 60Hz-51kHZ
Max SPL
SPDIF sampling rate 44.1 – 96kHz
Distortion < 0.5%
Input Sensitivity (0dBu = 0.775mV) -10dBu to +4dBu
Dispersion (@-6dB) 90 degrees
(2) 115dB
Drive Units- LF/MID 165mm (6”) multi fibre
Amplifier output power 75W LF / 35W HF
Outputs SPDIF slave out RCA
WideBand
TM
HF 25mm (1”) titanium
User Controls Front panel mounted
on/standby/mute switch, multi-function LED,
Shielded Yes
Electronic System
Inputs 600Ω balanced
paper pulp cone
dome neodymium
magnet system
Rear panel mounted trim +6/-12dB,
80Hz high pass switch for AV use,
16-way Activ-Assist
balanced XLR/1/4” jack
combination, SPDIF RCA
for a max SPL of 115dB
TM
switch array
XLR/Jack
Reveal 6D
Active near field reference monitor with Activ-Assist™
SPDIF Sample Rate 44.1 – 96kHz
Optimised bass-reflex loaded cabinet with 40mm thick front baffle
Sensitivity 775mV for 100W
Shielded 165mm (61/2”) woofer, multi fibre paper pulp cone
Shielded 25mm (1”) titanium dome neodymium tweeter
WideBand
Features:
Active bi-amplification (75W LF / 35W HF)
40mm thick contoured baffle
TM
HF extended to 51kHz corrects phase response
Driver lossy-coupled to cabinet
A whole generation of artists and producers have built their award-winning recordings
10 screw driver chassis fixing
on the original Reveal active; now the Reveal 6D takes nearfield monitoring to
Flux control rings on LF drivers
a new level. Incorporating Tannoy’s exclusive Activ-Assist™ technology allows
you to tune the monitor to the room’s acoustics for an unparalleled sonic
integration. Go ahead and connect it directly to the SPDIF output from
Applications:
your DAW, or stay in the analogue
Home studios/composition
Project studios, users of PC/MAC
DAW’s
Professional recording, broadcast,
post production studios & editing suites
SPDIF RCA
PERFORMANCE 5A
Frequency response
Max SPL
(2) 109dB
(1) 70Hz-30kHZ
Distortion <0.7%
Dispersion @-6dB, 10kHz, horizontal 90 degrees
DRIVE UNITS
Drive Units – LF/MID 130mm (5”) multi fibre
paper pulp cone
TM
WideBand
HF 25mm (1”) soft dome,
neodymium magnet system.
ELECTRONIC SYSTEM
Inputs 600
balanced XLR/1/4”
jack combination
Sensitivity 775mV for 40W
Amplifier output power 40W LF / 20W HF
User controls Front panel mounted
on/standby/mute switch, multi-function LED,
gain control
Cabinet dimensions 298.8 x 271.5 x 184mm
3
(HxWxD exc. heatsink) 11
/4 x 103/4 x 71/4”
Reveal 5A
Active compact reference monitor
Ultra high bandwidth response out to 30kHz
Optimised bass-reflex loaded cabinet with 40mm thick front baffle
Shielded 130mm (5”) woofer, multi fibre paper pulp cone
Shielded 25mm (1”) soft dome neodymium tweeter
Features:
40mm thick contoured baffle
Whether you’re building a studio on a budget, or you just need an active monitor
Driver lossy-coupled to cabinet
with a small footprint, the Reveal 5A is your choice. Built to the same high standard
10 screw driver chassis fixing
as the rest of the Reveal line, the R5A packs performance, accuracy and value
Flux control rings on LF drivers
into a compact enclosure that’s ready to share the desktop with the rest of
your gear. Priced right for the beginner, the R5A delivers WideBand™
performance that will impress even the most seasoned pro.
Applications:
Home studios/composition
Project studios, users of PC/MAC
DAW’s
Professional recording, broadcast,
post production studios & editing suites
The Antidote to Compromise
Few if any manufacturers have the reputation and track record of Tannoy in the professional
studio monitor market. Right from the emergence of the studio monitor itself as a product
in the early 1940’s through the British invasion of the ‘60’s and every genre of music since
then, Tannoy has been helping track, mix and master the hits.
You don’t dominate a segment for over 60 years by cutting corners.
You do it by staying true to your values; and letting others chase the latest fad or cheapest
option. Considering the crucial role that monitors play in the production of audio
programming we believe that this is one place in your signal chain where compromise
is simply unacceptable.
See and hear the Tannoy Reveal range at an authorized dealer near you and see for
yourself why Reveal is truly the antidote to compromise.
Tannoy United Kingdom T: +44 (0) 1236 420199 F: +44 (0) 1236 428230 E: enquiries@tannoy.com
Tannoy North America T: (519) 745 1158 F: (519) 745 2364 E: inquiries@tannoyna.com
Tannoy Deutschland T: (04102) 888 393 F: (04102) 888 959 E: info@tannoy.com
6483 0944
Loading...