Tannoy iw62 TDC User Manual
iw62 TDC
Product Description
The iw62 TDC is a full bandwidth in wall speaker system, using a 165mm (6.50") Tannoy
Dual Concentric™ point source, constant directivity drive unit with an additional 165mm
(6.50") bass driver and 25mm (1.00") Tannoy SuperTweeter™. Designed primarily for
installation into standard stud partition wall systems, it may also be used in cavity wall
installations constructed with standard thickness drywall as well as a wide range of other
wall construction types with a surface thickness of up to 25mm (1.00”).
The 165mm (6.50") Tannoy Dual Concentric™ drive unit comprises a multi fibre paper pulp
mid bass cone and a 25mm (1.00") ferrofluid cooled, titanium dome HF unit with
neodymium magnet system. The mid-bass and tweeter sections of this constant directivity
driver are coincidentally aligned to a true point source; ensuring a wide and controlled
dispersion for optimum coverage; this while avoiding the massive loss of energy, in the
vertical plane at the crossover frequency, inherent in two-way discrete designs.
An additional acoustically matched 165mm (6.50") bass driver delivers low frequency
reinforcement for the Dual, while a 25mm (1.00") titanium dome SuperTweeter™ extends
the frequency bandwidth out to over 50kHz. Not only does this further enhance the already
class leading, low distortion performance with an exceptionally natural and open
soundstage, it also ensures that this is a high output, high impact performer. The iw6 TDC
is equipped with dynamic high frequency protection.
The drivers and passive frequency dividing network are mounted in an injection moulded,
paintable front baffle manufactured from UV/weather resistant UL94V-0 ABS material.
The class leading performance is further enhanced by the inclusion of eight self aligning,
spring loaded clamps; allowing for quick install but also for simple removal or reorientation
of the loudspeaker. The rigidity of the clamps and baffle combination crucially provides the
acoustically optimum bond to the wall surface without risk of distortion to the baffle itself.
Gold plated spring loaded terminals are provided for ease of installation and a steel back
can is available as an optional installation accessory.
Features
• Extended frequency response and very low distortion
• Wide, controlled constant directivity dispersion for
optimum coverage
• Does not suffer from massive loss of energy in the
vertical plane at crossover caused by two way
discrete designs
• UV/weather resistant UL94V-0 ABS construction for
structural integrity
• Dynamic high frequency protection
• Eight way self-aligning clamp mounting system
• Ferrofluid cooled neodymium high frequency driver
• Five year warranty
Applications
• Foreground music & paging systems
• Multi-room audio systems
• Home theatre
• Business music systems
• Boardrooms and offices
• Retail environments
• Retail outlets and shopping malls
• Lounges and bars
• Cruise ships
• Courtrooms
Complementing any style of decor, the perforated metal grille and discreet moulded baffle
can be painted to blend seamlessly with any environment. Ideally suited to applications
requiring the combination of intelligibility, premium sonic quality for music and speech
reinforcement and exceptional reliability, the high power handling iw62 TDC is particularly
suited to custom AV installations and business music systems.
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: anfragen@tannoy.com
E: ventes@tannoy.com
iW62TDC data file issue:1.06 // 15.01.08
iw62 TDC
TECHNICAL SPECIFICATIONS
System iw62 TDC
1)
requency Response (-3dB)
F
Frequency Range (-10dB)
System Sensitivity (1W @1m)
Nominal Coverage Angle 90 degrees conical
overage Angle (1kHz to 6kHz) 120 degrees conical
C
Directivity Factor (Q) 4.6 averaged 1kHz to 6kHz
Directivity Index (DI) 6.0 averaged 1kHz to 6kHz
Rated Maximum SPL
Average 112dB
verage 110dB
A
eak 118dB
P
Power Handling
Average 105W
Programmed 210W
Peak 420W
Recommended Amplifier Power 210W @ 8 Ohms
Nominal Impedance 8 Ohms
Distortion
10% Full Power (5.5V) 2nd Harmonic 3rd Harmonic
250Hz 0.64% 0.06%
1kHz 0.6% 0.52%
10kHz 0.69% 0.06%
1% Full Power (1.73V) 2nd Harmonic 3rd Harmonic
250Hz 0.18% 0.11%
1kHz 0.08% 0.23%
10kHz 0.27% 0.17%
Crossover Passive, 750Hz, 1.8Hz, 16Hz
Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis.
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
(
0Hz - 51kHz
7
(1)
34Hz - 54kHz
(2)
92dB (1W - 2.83V for 8 Ohms)
(3)
with optional THP60 transformer)
(
Transducers
Dual Concentric™ Point source constant directivity drive unit
Low Frequency 1 x 165mm (6.50”) with multi fibre paper pulp cone
igh Frequency 19mm (0.75”) titanium dome with neodymium
H
magnet system
Supertweeter™ 19mm (0.75”) titanium dome with neodymium
magnet system
Low Frequency 1 x 165mm (6.50”) additional bass driver
Physical
Enclosure Baffle UL 94V-0 rated ABS
Optional accessory: Back can Zinc plated steel
Clamping Design Eight way self aligning security toggle clamp system
Connectors Gold plated connectors with spring terminals
Hole Cutout Size 426.10 x 187.6 (16.76 x 7.39”)
Dimensions
Front Baffle 473.5mm x 227mm (18.64” x 8.94”) (H x W)
Front of wall to rear 99mm (3.90”)
of magnet assembly
Net Weight 5kg (11lbs)
Included Accessories
Optional Accessories
Transformer Taps
70V
100V
rille Steel, with weather resistant coating
G
Maximum wall thickness - 25mm (1.00”)
Painted mask, cutout template, grille
Steel back can
Steel back can with THP60 transformer
Plaster (mud) ring
(optional)
60W / 30W / 15W / 7.5W / OFF & Low Impedence operation
60W / 30W / 15W / OFF & Low Impedence operation
Ordering Information
PART NUMBER PACKED QUANTITYCOLOURMODEL NAME
8000 3770 iw62 TDC White 1
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: anfragen@tannoy.com
E: ventes@tannoy.com
iW62TDC data file issue:1.06 // 15.01.08
50
60
70
80
9
0
1
00
10 100 1000 10000 100000
0
5
10
15
20
25
30
35
40
1 10 100 1000 10000 100000
50
60
70
80
90
100
10 100 1000 10000 100000
0 deg
10 deg
20deg
30deg
40deg
NECHOIC
A
FREQUENCY
RESPONSE
iw62 TDC
PERFORMANCE MEASUREMENTS
m on-axis frequency response
1
SPL, 1W/1m (dB)
frequency (Hz)
Impedance vs frequency
Impedance (ohms)
IMPEDANCE
Level (dB)
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
OFF AXIS
RESPONSE
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: anfragen@tannoy.com
E: ventes@tannoy.com
frequency (Hz)
Horizontal off-axis response
frequency (Hz)
iW62TDC data file issue:1.06 // 15.01.08
Loading...