Tannoy DI6T, DI6 DCT, DI5T, DI5 DC, Di5 User Manual

THE

RAN GE

USER MANUAL

Di5, Di5t,
Di5 DC & Di5 DCt
Di6, Di6t,
Di6 DC & Di6 DCt
Di8 DC & Di8 DCt

3

INTRODUCTION

3

SAFETY INSTRUCTIONS

4

PRODUCT IDENTIFICATION

5

STANDARD AND OPTIONAL ACCESSORIES

6-9

INSTALLATION GUIDELINES

6 Installation using supplied yoke bracket

7 Installation using optional K-Ball

8 Installation using supplied yoke bracket with optional pole-mount adaptor

9 Installation using optional K-Ball

10

PRODUCT DIMENSIONS

11

HARDWARE DIMENSIONS

TM

bracket

TM

bracket with optional pole-mount adaptor

12-13

14

14

15

2

TECHNICAL SPECIFICATIONS

12 Di ICT

13 Di Dual Concentric

TM

specifications

TM

specifications

PAINTING

WARRANTY STATEMENT

DECLARATION OF CONFORMITY

THE

Designed for a wide variety of sound reinforcement applications the Tannoy Di is an ultra compact loudspeaker system
capable of delivering high sound pressure levels with extremely low distortion, resulting in outstanding clarity, definition and
detail. A truly universal solution, the Di offers outstanding durability and resistance to scuffs and knocks. Able to deliver
consistent performance under a wide range of adverse conditions the Di is suited to applications indoors or out, whether it be
a theme bar or theme park. Available in black or white the Di will effectively blend into most backgrounds. Utilisation of the
point source loudspeaker allows the Di to be mounted on a wall or ceiling in either horizontal or vertical orientations without
affecting its performance. A range of hardware options ensures simple and effective installation. Also available with built in
line transformer.

For applications requiring extended low frequency enhancement, a range of Tannoy sub-bass systems are available and can
be used in conjunction with the Di.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. The user is responsible for fixing the hardware to the surface to ensure safe operation. The fixings must support the
weight of the product – please consult the manual’s specification page for the appropriate weights. Please consult the
relevant construction codes in your region for further information on suitable hardware fixing methods.

RANG E

USER MANUAL

6. Some regional construction codes require the use of a secondary method of securing loudspeakers to surfaces to provide
security of a back-up support. A secondary support line should be attached from the safety loop on the rear of the product
to a source point on the wall. Please consult the relevant construction codes in your region.

7. Tannoy will not be held accountable for any damage caused by incorrect installation.

3

GRILLE TRIM

Lift the grille trim back using the
tab to access the transformer
tapping switch on transformer
models.

GRILLE

YOKE TRIM

Remove the yoke trims on the top
and bottom panels to access the
yoke bracket fixing point

INPUT CONNECTOR

Remove the rubber grommet to
access the connector. The
rubber grommet ensures the rear
of the product is kept water-tight

SAFETY TAB

4

GRILLE

THE

RANG E

USER MANUAL

GRILLE TRIM

YOKE BRACKET

(SUPPLIED WITH
FIXINGS)

K-BALLTMBRACKET

POLE MOUNT ADAPTOR

5

USING SUPPLIED YOKE BRACKET

1. Fix the yoke bracket

to the surface using a
suitable fixing method.

5. For connection to the
loudspeaker, use pins
1 (+) and 2 (-).

Pins 3 (-) and 4 (+) are
in parallel for connection
to additional speakers in
a distributed line.
Note: Even if pins 3 and
4 are not used, they
should be tightend to
prevent the screws from
vibrating.

2. Remove the yoke
trims from the product
to access the bracket
fixing points.

6. Offer the speaker up
to the bracket and
attach it using a 5mm
alan key and supplied
fixings.

3. Remove the rubber
grommet from the rear of
the speaker. Inclusion of
the rubber grommet is
only required if installing
the product outdoors.

7. Connect the euro
plug then replace the
rubber grommet to
ensure the speaker is
watertight.

4. Feed the speaker
cable through the rubber
grommet then connect
the euro-type plug to the
wires, observing the
correct polarity.

8. Connect a secondary
support line to the
safety tab at the rear of
the cabinet.

TRANSFORMER
MODELS ONLY

9. Lift the grille trim

using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found on
the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.

6

TRANSFORMER
MODELS ONLY

10. The Di5t and Di5

DCt models are fitted
with 30W transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.

TRANSFORMER
MODELS ONLY

11. The Di6t, Di6 DCt,

& Di8 DCt models are
fitted with 60W
transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

USING OPTIONAL K-BALLTMBRACKET

THE

RANG E

USER MANUAL

1. If attaching the
K-BallTMbracket to a
flush mounted inwall
conduit junction box
(J-box), pass the
speaker wire through the
bracket adaptor plate
then attach the adaptor
plate to the J-box using
the fixings provided.

5. Offer the speaker up
to the K-BallTMBracket.
Push the speaker onto
the bracket to engage
the euro plug.

2. Connect the speaker
wires to the connector
block in the bracket.
For connection to an
amplifier use pins 1 (+)
and 2 (-)
Pins 3 (-) and 4 (+) are
in parallel for
connection to additional
speakers in a
distributed line.

6. Fit the rubber
grommet and finger­tighten the bracket bolt
while supporting the
speaker. If the
connector has engaged
properly the speaker
will lock onto the
bracket

3. If a conduit junction
box has been used,
offer the bracket up to
the adaptor plate, with
the foam gasket**
squeezed in between
the J-box and the wall.
Attach the bracket to
the surface using a
suitable fixing method*.

7.Swivel the speaker
into position then use
a 19mm wrench to give

1

another 2

/2turns to
ensure the speaker is
locked in position.

4. If you are attaching
the bracket directly to a
surface, offer the
bracket up to the
surface with the foam
gasket** squeezed in
between. Attach the
bracket to the surface
using a suitable fixing
method*.

8. Connect a secondary
support line to the
safety tab at the rear of
the cabinet.

TRANSFORMER
MODELS ONLY

9. Lift the grille trim

using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found on
the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.

TRANSFORMER
MODELS ONLY

10. The Di5t and Di5

DCt models are fitted
with 30W transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET
FOR LOW IMPEDANCE.

TRANSFORMER
MODELS ONLY

11. The Di6t, Di6 DCt,

& Di8 DCt models are
fitted with 60W
transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

NOTE

* See safety notices on

page 3

** The foam gasket is

intended to provide a
water tight seal.
Inclusion of the foam
gasket is only a
requirement if

installing outdoors.

7

IUSING OPTIONAL POLE MOUNT ADAPTOR
IWITH SUPPLIED YOKE BRACKET

1. Use the supplied
fixings to fix the yoke
bracket to the pole
bracket adaptor.

Note that the Di5 models
require 2 fixing screws
whereas the Di6 and Di8
models require 4 fixing
screws.

5. Feed the speaker
cable through the rubber
grommet then connect
the euro-type plug to the
wires, observing the
correct polarity.

2. Fix the pole mount
bracket adaptor to the
pole using the strapping
provided. The bracket
can be mounted in
portrait or landscape
orientations.

6. For connection to the
loudspeaker, use pins 1
(+) and 2 (-)

Pins 3 (-) and 4 (+) are
in parallel for connection
to additional speakers in
a distributed line.
Note: Even if pins 3 and
4 are not used, they
should be tightend to
prevent the screws
from vibrating.

3. Remove the yoke
trims from the product
to access the bracket
fixing points.

7. Offer the speaker up
to the bracket and
attach it using a 5mm
alan key and supplied
fixings.

4. Remove the rubber
grommet from the rear
of the speake. Inclusion
of the rubber grommet is
only required if installing
the product outdoors.

8. Connect the euro
plug then replace the
rubber grommet to
ensure the speaker is
watertight.

9. Connect a secondary
support line to the safety
tab at the rear of the
cabinet.

8

TRANSFORMER
MODELS ONLY

10. Lift the grille trim

using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found
on the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.

TRANSFORMER
MODELS ONLY

11. The Di5t and Di5

DCt models are fitted
with 30W transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

TRANSFORMER
MODELS ONLY

12. The Di6t, Di6 DCt,

& Di8 DCt models are
fitted with 60W
transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

USING POLE MOUNT ADAPTOR

WITH OPTIONAL K-BALLTMBRACKET

THE

RANG E

USER MANUAL

1. Pass the speaker wire
through the pole-mount
adaptor plate then fix the
pole mount bracket
adaptor to the pole using
the strapping provided.
The bracket can be
mounted portrait or
landscape orientations.

5. Remove the rubber
grommet from the rear of
the speaker then offer
the speaker up to the

TM

K-Ball

Bracket.

2. Connect the speaker
wires to the connector
block in the rear of the
K-BallTMbracket.
For connection to an
amplifier use pins 1 (+)
and 2 (-).
Pins 3 (-) and 4 (+) are
in parallel for
connection to additional
speakers in a
distributed line.

6. Finger-tighten the
bracket bolt to extend
the bracket out to
connect with the euro
plug socket. Position
speaker then use a
19mm wrench to give

1

another 2

/2turns to
ensure the speaker is
locked in position.

3. Offer the K-Ball

TM

bracket up to the
adaptor plate, with the
foam gasket**
squeezed in between.
Use the supplied fixings
to fix the K-Ball

TM

bracket to the pole
bracket adaptor.

7.Connect a secondary
support line to the
safety tab at the rear of
the cabinet.

4. Fix the pole mount
bracket adaptor to the
pole using the strapping
provided. The bracket
can be mounted in
portrait or landscape
orientations.

TRANSFORMER
MODELS ONLY

8. Lift the grille trim

using the tab to access
the rotary transformer
tapping switch. The
rotary switch is found
on the top of the Di5
models, and on the
bottom of the Di6 and
Di8 models.

TRANSFORMER
MODELS ONLY

9. The Di5t and Di5 DCt

models are fitted with
30W transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

TRANSFORMER
MODELS ONLY

10. The Di6t, Di6 DCt,

& Di8 DCt models are
fitted with 60W
transformers.

THE SPEAKER IS SUPPLIED
IN LOW IMPEDANCE MODE.
NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT
AMPLIFIER WHILE IT IS SET

FOR LOW IMPEDANCE.

NOTE

** The foam gasket is

intended to provide a
water tight seal.
Inclusion of the foam
gasket is only a
requirement if

installing outdoors.

9

Di5

Di6

10

Di8

65.0

[2.56"]

180.0

[7.09"]

R15.0

[R0.59"]

241.0

[9.49"]

123.0

[4.84"]

54.0

[2.13"]

R15.0

[R0.59"]

85.0

[3.35"]

90.0

[3.54"]

6.0

[0.24"]

?22.0

[?0.87"]

35.0

[1.38"]

358.0

[14.09"]

145.0

[5.71"]

150.0

[5.91"]

35.0

[1.38"]

6.0

[0.24"]

?22.0

[?0.87"]

[2.56"]

R15.0

[R0.59"]

217.0

[8.54"]

70.0

[2.76"]

406.0

[15.98"]

165.0 170.0

47.7

[1.88"]

137.9

[5.43"]

93.2

[3.67"]

155.0

[6.10"]

65.0

[2.56"]

165.0

[6.50"]

170.0

[6.69"]

35.0

[1.38"]

R11.0

[R0.43"]

[

5” YOKE BRACKET

6” YOKE BRACKET

THE

RANG E

USER MANUAL

8” YOKE BRACKET

K-BALL

TM

BRACKET

11

TM

ICT

MODELS

Di5 Di6

SYSTEM

Frequency Response (-3dB)

Frequency Range (-10dB)

System Sensitivity (1W @1m)

1W = 2.45V for 6 Ohms

Dispersion 90 90
Degrees conical -6dB

Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”)
Mineral loaded polypropylene

High Frequency Driver ICT

Crossover 7kHz 7kHz

Inductively Coupled ICT™

(1)

(1)

(2)

90Hz - 25kHz 75Hz - 22kHz

80Hz - 30kHz 55Hz - 24kHz

88dB 90dB

TM

ICT

TM

Directivity Factor (Q) 1kHz to 10kHz 5.3 averaged 10.5 averaged

Directivity Index (DI) 1kHz to 10kHz 6.6 averaged 8.4 averaged

(2)

Rated Maximum SPL

Average 105dB 107dB

Peak 111dB 113dB

Power Handling Average 50W 60W

Programme 100W 120W

Peak 200W 240W

Recommended Amplifier Power 100W @ 6 Ohms 120W @ 6 Ohms

Nominal Impedance 6 Ohms 6 Ohms

Distortion 10% Full Power (5.5V) 2nd Harmonic 3rd Harmonic (6.0V) 2nd Harmonic 3rd Harmonic

250Hz 2.00% 0.26% 1.86% 0.12%

1kHz 0.53% 0.19% 1.17% 0.54%

10kHz 2.50% 0.35% 1.10% 0.04%

Distortion 1% Full Power (1.73V) 2nd Harmonic 3rd Harmonic (1.9V) 2nd Harmonic 3rd Harmonic

250Hz 0.65% 0.09% 0.70% 0.14%

1kHz 0.144% 0.11% 0.45% 0.39%

10kHz 0.52% 0.298% 0.25% 0.065%

CONSTRUCTION

Enclosure Weather resistant high impact polystyrene (HIPS), IP64 to EN60529 (IEC529)

Grille Steel, with weather resistant coating

Finish Textured black or white paint with matching rubber trims

Factory fitted custom trim colours available to special order

Connectors Removable locking Euroblock type connector

with screw terminals and "loop through" facility

Fittings 1 x socket for K-Ball™ bracket and 2 x M8 yoke bracket inserts

Supplied Accessory Yoke bracket

Dimensions 240.7 x 155.0 x 162.0mm 357.5 x 230.0 x 223.2mm

9.47 x 6.10 x 6.38” 14.08 x 9.05 x 8.79”

Weight 2.2kg (4.85lbs) 3.7kg (8.15lbs)

TRANSFORMER VERSIONS Di5t Di6t

Specifications as above except:

Transformer Taps 70V
Rotary switch & Low Impedance operation & Low Impedance operation
mounted under trim

100V

*

Rated Maximum SPL

(2)

Average 103dB (using 30W transformer tap) 107dB (using 60W transformer tap)

30W / 15W / 7.5W / 3.75W / OFF 60W / 30W / 15W / 7.5W / OFF

30W / 15W / 7.5W / OFF & 60W / 30W /15W / OFF &
Low Impedance operation Low Impedance operation

Weight 2.7kg (5.94lbs) 5.0kg (11.02lbs)

*

See Passive models above for max SPL figures on low impedance settings.

12

Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis in an anechoic chamber
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber

A full range of measurements, performance data, and EaseTMData can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notice.

DUAL CONCENTRIC

Di5 DC Di6 DC Di8 DC

SYSTEM

Frequency Response (-3dB)

Frequency Range (-10dB)

System Sensitivity (1W @1m)

1W = 2.83V for 8 Ohms

Dispersion 90 90 90
Degrees conical -6dB

Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”) 1x 200mm (8.00”)
Dual Concentric
with a resin treated multi fibre paper pulp cone

High Frequency Driver 19mm (0.75”) 25mm (1.00”) 25mm (1.00”)
titanium dome with neodymium magnet system

Crossover 2kHz - 2nd order LF, 1.6kHz - 2nd order LF, 1.5kHz - 2nd order LF,

Directivity Factor (Q) 1kHz to 10kHz 5.3 averaged 5.6 averaged 5.5 averaged

Directivity Index (DI) 1kHz to 10kHz 6.6 averaged 7.0 averaged 7.0 averaged

Rated Maximum SPL

Power Handling Average 60W 90W 90W

Recommended Amplifier Power 120W @ 8 Ohms 180W @ 8 Ohms 180W @ 8 Ohms

Nominal Impedance 8 Ohms 8 Ohms 8 Ohms

Distortion 10% Full Power (6.9V) 2nd Harmonic 3rd Harmonic (8.0V) 2nd Harmonic 3rd Harmonic (8.5V) 2nd Harmonic 3rd Harmonic

250Hz 4.00% 0.20% 1.00% 0.32% 1.55% 0.42%

1kHz 0.76% 0.60% 0.18% 0.32% 0.41% 0.63%

10kHz 0.65% 0.15% 1.00% 0.18% 1.20% 0.65%

Distortion 1% Full Power (2.2V) 2nd Harmonic 3rd Harmonic (2.5V) 2nd Harmonic 3rd Harmonic (2.7V) 2nd Harmonic 3rd Harmonic

250Hz 2.00% 0.15% 0.25% 0.25% 0.43% 0.48%

1kHz 0.009% 0.124% 0.06% 0.18% 0.07% 0.47%

10kHz 0.32% 0.17% 0.45% 0.14% 0.55% 0.13%

TM

constant directivity driver

(1)

(1)

(2)

88dB 89dB 91dB

(2)

Average 106dB 109dB 111dB

Peak 112dB 115dB 117dB

Programme 120W 180W 180W

Peak 240W 360W 360W

90Hz - 50kHz 75Hz - 30kHz 65Hz - 30kHz

80Hz - 54kHz 55Hz - 35kHz 53Hz - 35kHz

2nd order HF with 2nd order HF with 2nd order HF with
Dynamic HF protection Dynamic HF protection Dynamic HF protection

TM

MODELS

THE

RANG E

USER MANUAL

CONSTRUCTION

Enclosure Weather resistant high impact polystyrene (HIPS), IP64 to EN60529 (IEC529)

Grille Steel, with weather resistant coating

Finish Textured black or white paint with matching rubber trims

Factory fitted custom trim colours available to special order

Connectors Removable locking Euroblock type connector

with screw terminals and "loop through" facility

Fittings 1 x socket for K-Ball™ bracket and 2 x M8 yoke bracket inserts

Supplied Accessory Yoke bracket

Dimensions 240.7 x 155.0 x 162.0mm 357.5 x 230.0 x 223.2mm 404.3 x 260.0 x 260.3mm

Weight 2.2kg (4.85lbs) 5.0kg (11.02lbs) 6.0kg (13.23lbs)

TRANSFORMER VERSIONS Di5 DCt Di6 DCt Di8 DCt

Specifications as above except:

Transformer Taps 70V
Rotary switch & Low Impedance operation & Low Impedance operation & Low Impedance operation
mounted under trim

100V

*

Rated Maximum SPL

Weight 2.7kg (5.95lbs) 5.5kg (12.12lbs) 7.0kg (15.87lbs)

*

See Passive models above for max SPL figures on low impedance settings.

(2)

Average 106dB

9.47 x 6.10 x 6.38” 14.08 x 9.05 x 8.79” 15.92 x 10.24 x 10.25”

30W / 15W / 7.5W / 3.75W / OFF 60W / 30W / 15W / 7.5W / OFF 60W / 30W / 15W / 7.5W / OFF

30W / 15W / 7.5W / OFF & 60W / 30W / 15W / 7.5W / OFF 60W / 30W / 15W / OFF &

Low Impedance operation Low Impedance operation Low Impedance operation

(103dB - 30W transformer tap)

109dB

(107dB - 60W transformer tap)

111dB

(109dB - 60W transformer tap)

Notes:
(1) Average over stated bandwidth. Measured at 1 metre on axis in an anechoic chamber
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber

A full range of measurements, performance data, and EaseTMData can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notice.

13

All Di products can be custom painted. If you choose to paint your product, the entire product should be spray painted with the
grille and grille trim still attached to the cabinet. Flexible vinyl paint should be used and care must be taken not to over apply
paint, especially to the grille.

No maintenance of the Di loudspeaker is necessary.

All of our products have been produced and tested with care and precision to give first-class service.

All passive components are guaranteed for a period of five years from the date of purchase from an authorised Tannoy dealer
subject to the absence or evidence of misuse, overload, or accidental damage.

All active and electronic components are guaranteed for a period of one year from the date of purchase from an authorised
Tannoy dealer subject to the absence of, or evidence of, misuse, overload or accidental damage.

If at any time during this warranty period the equipment proves to be defective for any reason other than accident, misuse,
neglect, unauthorised modification or fair wear and tear, we will repair any such manufacturing defect or, at our option, replace it
without charge for labour, parts or return carriage.

If you suspect a problem with a Tannoy product then, in the first instance, discuss it with your Tannoy dealer. If you require further
assistance then we ask that you deal directly with your local Tannoy distributor. If you cannot locate your distributor please contact
Customer Services, Tannoy Ltd at the address given below.

Customer Services, Tannoy Ltd., Rosehall Industrial Estate, Coatbridge, Strathclyde ML5 4TF, Scotland

Telephone: [phone] (National)

[phone] (International)

Fax: [phone] (National)

[phone] (International)

E-mail: [e-mail]

DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION

Our policy commits us to incorporating improvements to our products through continuous research
and development. Please confirm current specifications for critical applications with your supplier.

14

The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF
and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives
relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic
disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to
operate as intended, and, the apparatus has an adequate level of intrinsic immunity to electromagnetic disturbance to enable
operation as specified and intended.

THE

RANG E

Details of the Apparatus: Tannoy Contractor Loudspeaker

Model Number: Di

Associated Technical File: EMCi6
Applicable Standards: EN 50081-1 Emission

EN 50082-1 Immunity

Signed:
Position: Director of Engineering (Professional)
Date: 11th Dec. 06

USER MANUAL

15

REVISION DATE: 19 Feb ‘07

Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: [e-mail]
Tannoy North America T: 00 1 [phone] E: [e-mail]
Tannoy Deutschland T: 00 49 (180) 1111 881 E: [e-mail]
Tannoy France T: 00 33 (0)1 7036 7473 E: [e-mail]

Tannoy adopts a policy of continuous improvement and product specification is subject to change.

6481 0471 02/06