Tannoy CVS 8, CVS 6, CVS 4 Installation Manual

6481 0487
Tannoy has a policy of continuous improvement and this specification sheet provides the latest information at the time of printing.
All specifications may be subject to further change. Please contact the Tannoy website for the latest information.
CVS 4 CVS 6 CVS 8
INSTALLATION MANUAL
CVS 4 TEMPLATE CUTOUT SIZE: 180mm CVS 6 TEMPLATE CUTOUT SIZE: 250mm
AT
CVS 8 TEMPLATE CUTOUT SIZE: 320mm
;HUUV`°+PYLJ[°<2 ;*.0°96>°ZHSLZ
° ;!°°°°° ,!°LUX\PYPLZ'[HUUV`JVT
;!°° ° ,!°PUMV'[JNYV\WPU[LYUH[PVUHSJVT ;*.((TLYPJHZZHSLZ ;!°°° °° ,!°PUMV'[JNYV\WHTLYPJHZJVT ;HUUV`°4PKKSL°,HZ[ ;!° ° ,!°LUX\PYPLZ'[HUUV`JVT
;HUUV`°HKVW[Z°H°WVSPJ`°VM°JVU[PU\V\ZPTWYV]LTLU[HUK° WYVK\J[°ZWLJPMPJH[PVU°PZ°Z\IQLJ[°[VJOHUNL°
2
TSNETNOC
3
INTRODUCTION
1
UNPACKING
2
SAFETY NOTICES
3
ACCESSORIES
5
INSTALLATION GUIDE
6
MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS
MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK CEILINGS
MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING
WIRING AND SETTING UP
DIMENSIONS
CVS 4 DIMENSIONS
CVS 6 DIMENSIONS
TECHNICAL SPECIFICATIONS
WARRANTY
DECLARATION OF CONFORMITY
6.1
6.2
6.3
7
8
8.1
8.2
9
11
12
CVS 8 DIMENSIONS8.3
SAFETY NOTE: In order to comply with the relevant fire safety regulations (ie. BS 5839:1998), it is required that in the event of fire,
that failure of the circuit to which the loudspeaker is connected does not occur before evacuation of the building is complete. Suitable measures include: ­ a) use of terminal blocks (for connection to primary) with a melting point of not less than 650°C, for example constructed from ceramic materials; b) use of terminal blocks of a lower melting point but protected with thermal insulation; c) use of terminal blocks such that, on melting, an open-circuit or a short-circuit does not occur.
1. INTRODUCTION
Thank you for purchasing this Tannoy Ceiling loudspeaker.This product range is suited for high­level music and speech reinforcement applications requiring exceptional sonic quality with uncompromised reliability.
2. UNPACKING
Every Tannoy product and accessory is carefully inspected before packing. After unpacking, please inspect your product to make sure no damage has occurred in transit. In the unlikely event of any damage, would you please notify your dealer immediately and retain your shipping carton, as your dealer may ask you to return the faulty unit to them for inspection.
Each CVS loudspeaker is packed in pairs and provided with the following accessories as standard; C Ring, tile-bridge kit, grille, cut-out template, and paint mask. A plaster (mud) ring is also available as an optional extra.
PAINTING10
3. SAFETY NOTICES
Some regional construction codes require the use of a secondary method of securing loudspeakers in ceiling to provide security of a backup support. A secondary support line should be attached from the safety loop on the rear of the product to a source point on the ceiling. Please consult the relevant construction codes in your region.
When using a power driver to install the product it is essential to use the correct torque level settings to avoid over tightening and damage to the ceiling material or clamps
Recommended torque setting: 1.5Nm Tannoy will not be held responsible for any damages caused by the improper installation of
these loudspeakers. Electrical Safety Notice: to comply with the standard UL1480 , metal-clad flexible conduit (BX) is
required for connection to the terminal block for proper earth grounding.
PRODUCT FEATURE IDENTIFICATION
4
Conduit/Cable Clamp
Safety Tab
Mounting Wings
4
5
4. PRODUCT FEATURE IDENTIFICATION: 5. ACCESSORIES:
Standard Accessories
C-Ring Tile bridge kit
Note: A tile bridge kit must always be used when installing into suspended ceiling tiles
Grille Cut-out template
Paint Mask
Optional Accessories
Plaster (Mud) Ring
CVS 4
CVS 6
CVS 8
Conduit/Cable Clamp
Mounting Wings
Safety Tab
Tuning Ports
Rotary Switch
Screws for mounting wings
Tuning Ports
Rotary Switch
Screws for mounting wings
Tuning Ports
Rotary Switch
Screws for mounting wings
Conduit/Cable Clamp
Mounting Wings
Safety Tab
6
6.1 MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS
Slide the tile panel back into the suspended ceiling. The tile bridge ends will catch over the railings, supporting the weight of the speaker.
5
Slide the speaker assembly through the hole and turn the screws on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved.
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
4
DO NOT OVERTIGHTEN!
Place the C-ring and tile-bridge on top of the ceiling panel, aligning the C-ring over the hole, and screw the C-ring to the tile bridge using the fixings provided.
3
Cut out the hole in the ceiling tile using a circular saw or pad saw.
2
Remove the ceiling tile from its frame and place it on a flat surface. Mark the cut-out area on the ceiling tile by tracing around the template provided.
1
Go to section 7 for instructions on wiring and set-up instructions.
6.2 MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK (PLASTER BOARD) CEILINGS
4
Go to section 7 for wiring and set-up instructions then return to point 4 below.
3
Cut out the hole in the ceiling using a circular saw or pad saw, then slide the C-ring into the ceiling, aligning it over the cut-out hole.
2
Mark the cut-out area on the ceiling by tracing around the template provided.
1
7
Connect a Secondary Support Line to safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
5
Connect a Secondary Support Line to safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
6
Insert grille by pushing it onto the speaker.
6
Slide the speaker assembly through the hole and turn the screws to extend the mounting wings. Tighten the screws until a firm grip is achieved.
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
8
9
6.3 MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING:
Lay the speaker wiring to where the speaker will be fitted and complete the plastering work on the ceiling.
2
Insert grille by pushing it onto the speaker.
7
Nail or screw the plaster ring to the joists.
1
An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings.
Cut out the hole in the ceiling using a circular saw or pad saw.
3
5
Go to section 7 for instructions on wiring then return to point 5 below.
4
7. WIRING AND SETTING UP:
The CVS 6 is fitted with a 60W transformer. When used in distributed-line systems, the transformer can be tapped at 60W, 30W, and 15W, with an additional 7.5W tapping for
70.7V line systems.
5
The CVS 8 is fitted with a 60W transformer. When used in distributed-line systems, the transformer can be tapped at 60W, 30W, and 15W, with an additional 7.5W tapping for
70.7V line systems.
6
Close the wiring cover and tighten both screws on the cable clamp. Use the rotary switch located on the front of the unit to select whether you wish to use the speaker in a low-impedance or distributed-line application.
3
THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE SPEAKER TO A 70/100 VOLT AMPLIFIER WHILE IT IS SET FOR LOW IMPEDANCE.
The CVS 4 is fitted with a 30W transformer. When used in distributed-line systems, the transformer can be tapped at 30W, 15W and 7.5W, with an additional 3.75W tapping for 70.7V line systems.
Connect a Secondary Support Line to safety tab. Some construction codes require use of this secondary support point, which should connect to a separate secure support point using a suitable support line. Consult construction codes in your region.
6
Slide the speaker assembly through the hole and turn the screws to extend the mounting wings.Tighten the screws until a firm grip is achieved.
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
4
Open the wiring cover at the back of the speaker can to access the Euro type connector plug and socket.
1
For connection to an amplifier, use pins 1 and 2:
Pin 1 is positivePin 2 is negative
For connection to additional speakers in a distributed line, pins 3 and 4 are in parallel where:
Pin 3 is negativePin 4 is positive
2
10
11
8.1 CVS 4 DIMENSIONS:
CVS 4 TEMPLATE CUTOUT SIZE: 180mm
8.2 CVS 6 DIMENSIONS:
CVS 6 TEMPLATE CUTOUT SIZE: 250mm
ø244.6 [9.63"]
246.5
[9.70"]
15.9
[0.63"]
258.5
[10.18"]
ø279.6
[11.01"]
ø174.8 [6.88"]
14.7
[0.58"]
202.5
[7.97"]
214.9
[8.46"]
ø213.0 [8.39"]
12
13
8.3 CVS 8 DIMENSIONS:
CVS 8 TEMPLATE CUTOUT SIZE: 320mm
355.6
[14.00"]
19.6
[0.77"]
251.0
[9.88"]
264.0
[10.39"]
315.2
[12.41"]
CVS4
TECHNICAL SPECIFICATIONS
System
Frequency Response (-3dB)
(1)
Frequency Range (-10dB)
(1)
System Sensitivity (1W @1m)
(2)
Nominal Coverage Angle
Coverage Angle (1kHz to 6kHz)
Directivity Factor (Q)
Directivity Index (DI)
Rated Maximum SPL
Power Handling
(3)
Average Programme Peak
Recommended Amplifier Power
Nominal Impedance
Transformer Taps
(via front rotary switch) 70V
100V
Distortion
1% Full Power 250Hz 1kHz 10kHz
10% Full Power 250Hz 1kHz 10kHz
Crossover Point
Notes (1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber (2) Unweighted Pink noise input, measured at 1m on axis" (3) Long term power handling capacity as defined in EIA - 426B test
CVS4
85Hz - 19kHz
77Hz - 22kHz
87dB (1W = 2.45V for 6 Ohms)
90 degrees conical
102 degrees
5.6 averaged 1kHz to 6kHz
7.1 averaged 1kHz to 6kHz
103dB (average) 109dB (peak)
40W 80W 160W
80W @ 6 Ohms
6 Ohms
30W / 15W / 7.5W / 3.75W / OFF & low impedance operation
30W / 15W / 7.5W / OFF & low impedance operation
2nd Harmonic 3rd Harmonic
0.231% 0.112%
0.229% 0.253%
0.163% 0.025%
2nd Harmonic 3rd Harmonic
0.99% 0.169%
0.816% 0.323%
0.444% 0.027%
2.7kHz
Transducers
Low Frequency High Frequency
100mm (4.00") Mineral Loaded 19mm (0.75")
Physical
Enclosure
Back can Baffle Grille
Safety Features
Clamping Design
Back Can Options
Cable Entry Options
Connectors
Safety Agency Ratings Hole Cutout Diameter Dimensions
Bezel diameter Front of ceiling to
rear of back can Front of ceiling to
top of safety loop
Net Weight (ea) Included Accessories
Optional Accessories
Zinc plated steel Reflex loaded UL 94V-0 rated ABS Steel, with weather resistant coating
Safety ring located at rear of enclosure for load bearing safety bond
Security toggle clamp
Cable clamp & squeeze connector for conduit up to 22mm
Removable locking connector with sctrew terminals with "loop through" facility
UL-1480, UL-2043, CE 180mm
213.0mm (8.39”)
202.5mm (7.97”)
214.9mm (8.46”)
2.60kg C Ring, tile bridge, paint mask,
cutout template, grille Plaster (mud) ring
14
15
CVS8
TECHNICAL SPECIFICATIONS
System
Frequency Response (-3dB)
(1)
Frequency Range (-10dB)
(1)
System Sensitivity (1W @1m)
(2)
Nominal Coverage Angle
Coverage Angle (1kHz to 6kHz)
Directivity Factor (Q)
Directivity Index (DI)
Rated Maximum SPL
Power Handling
(3)
Average Programme Peak
Recommended Amplifier Power
Nominal Impedance
Transformer Taps
(via front rotary switch) 70V
100V
Distortion
1% Full Power 250Hz 1kHz 10kHz
10% Full Power 250Hz 1kHz 10kHz
Crossover Point
Notes (1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber (2) Unweighted Pink noise input, measured at 1m on axis (3) Long term power handling capacity as defined in EIA - 426B test
CVS8
79Hz - 21kHz
60Hz - 24kHz
93dB (1W = 2.45V for 6 Ohms)
90 degrees conical
84 degrees conical
14.7 averaged 1kHz to 6kHz
11.7 averaged 1kHz to 6kHz
111dB (average) 117dB (peak)
60W 120W 240W
120W @ 6 Ohms
6 Ohms
60W / 30W / 15W / 7.5W / OFF & low impedance operation
60W / 30W / 15W / OFF & low impedance operation
0.33% 0.25%
0.15% 0.63%
0.12% 0.03%
1.10% 0.25%
0.55% 0.70%
0.52% 0.03%
6kHz
Transducers
Low Frequency
High Frequency
Coaxial 200 mm (8.00") mineral loaded cone material
19mm (0.75")
Physical
Enclosure
Back can Baffle Grille
Safety Features
Clamping Design
Back Can
Cable Entry Options
Connectors
Safety Agency Ratings (pending) Hole Cutout Diameter Dimensions
Bezel diameter Front of ceiling to
rear of back can Front of ceiling to
top of safety loop
Net Weight (ea) Included Accessories
Optional Accessories
Zinc plated steel
Blind Mount (BM) Reflex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating Safety ring located at rear of enclosure
for load bearing safety bond Security toggle clamp
Cable clamp & squeeze connector for conduit up to 22mm
Removable locking connector with sctrew terminals with "loop through" facility
UL-1480, UL-2043, CE 320mm (12.6")
355.6mm (14.00”)
251.0mm (9.88”)
264.0mm (10.39”)
Template hole cutout size
250mm (9.84")
5.3kg (11.68lbs) C Ring, tile bridge, paint mask,
cutout template, grille Plaster (mud) ring
CVS6
TECHNICAL SPECIFICATIONS
System
Frequency Response (-3dB)
(1)
Frequency Range (-10dB)
(1)
System Sensitivity (1W @1m)
(2)
Nominal Coverage Angle
Coverage Angle (1kHz to 6kHz)
Directivity Factor (Q)
Directivity Index (DI)
Rated Maximum SPL
Power Handling
(3)
Average Programme Peak
Recommended Amplifier Power
Nominal Impedance
Transformer Taps
(via front rotary switch) 70V
100V
Distortion
1% Full Power 250Hz 1kHz 10kHz
10% Full Power 250Hz 1kHz 10kHz
Crossover Point
Notes (1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber (2) Unweighted Pink noise input, measured at 1m on axis (3) Long term power handling capacity as defined in EIA - 426B test
CVS6
79Hz - 21kHz
60Hz - 24kHz
91dB (1W = 2.45V for 6 Ohms)
90 degrees conical
93 degrees
7.7 averaged 1kHz to 6kHz
8 averaged 1kHz to 6kHz
109dB (average) 115dB (peak)
60W 120W 240W
120W @ 6 Ohms
6 Ohms
60W / 30W / 15W / 7.5W / OFF & low impedance operation
60W / 30W / 15W / OFF & low impedance operation
2nd Harmonic 3rd Harmonic
0.439% 0.140%
0.396% 0.458%
0.235% 0.023%
2nd Harmonic 3rd Harmonic
1.16% 0.214%
1.014% 0.685%
0.944% 0.047%
2.5kHz
Transducers
Low Frequency
High Frequency
150mm (6.00") Mineral Loaded polypropylene ICT™
19mm (0.75")
Physical
Enclosure
Back can Baffle Grille
Safety Features
Clamping Design
Back Can
Cable Entry Options
Connectors
Safety Agency Ratings Hole Cutout Diameter Dimensions
Bezel diameter Front of ceiling to
rear of back can Front of ceiling to
top of safety loop
Net Weight (ea) Included Accessories
Optional Accessories
Zinc plated steel Reflex loaded UL 94V-0 rated ABS Steel, with weather resistant coating
Safety ring located at rear of enclosure for load bearing safety bond
Security toggle clamp
Cable clamp & squeeze connector for conduit up to 22mm
Removable locking connector with sctrew terminals with "loop through" facility
UL-1480, UL-2043, CE 250mm
279.5mm (11.01”)
246.5mm (9.70”)
258.5mm (10.18”)
4.75kg C Ring, tile bridge, paint mask,
cutout template, grille Plaster (mud) ring
1
6
1
7
12. DECLARATION OF CONFORMITY:
The following apparatus is/are manufactured in China for Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to operate as intended, and, the apparatus has an adequate level of intrinsic immunity to electromagnetic disturbance to enable operation as specified and intended. This equipment conforms to the requirements of the EMC Directive 89/336/EEC, amended by 92/31/EEC and the requirements of the Low Voltage Directive 73/23/EEC, amended by 93/68/EEC.
Details of the Apparatus: Tannoy Contractor Loudspeaker
Model Numbers: CVS 4
CVS 6 CVS 8
Applicable Standards: EN55103-1 1996 Emission
EN55103-2 1996 Immunity
Electrical Safety EN 60065: 1993
Signed:
Position: Director of Engineering
Tannoy Professional
Date: 23/11/2011
For Tannoy Ltd
10. PAINTING
If desired, the grille and baffle panel may be painted to match the surrounding décor. Painting the baffle:
Carefully mask off the driver assembly using the paint-mask provided to ensure that the paint does not come into
contact with the cone and roll surround.
Apply several thin coats of paint – this will provide a better finish than one overly thick coat.
Painting the grille:
Carefully remove the acoustically transparent foam from the reverse side of the grille. Paint the grille and then replace the foam - several thin coats of paint will provide a better finish than one
overly thick coat. Re-bond the foam to the grille over the entire area using a light spray-adhesive to avoid audible resonances.
11. WARRANTY
No maintenance of the CVS loudspeaker is necessary. All Tannoy professional loudspeaker products are covered by a 5 year warranty from the date of manufacture
subject to the absence of misuse, overload or accidental damage. Claims will not be considered if the serial number has been altered or removed. Work under warranty should only be carried out by a Tannoy Professional dealer or service agent. This warranty in no way affects your statutory rights. For further information please contact your dealer or distributor in your country. If you cannot locate your distributor please contact Customer Services, Tannoy Ltd at the address given below.
Customer Services Tannoy Ltd. Rosehall Industrial Estate Coatbridge Strathclyde ML5 4TF Scotland
Tel: 01236 420199 (National) +44 1236 420199 (International) Fax: 01236 428230 (National) +44 1236 428230 (International) E-mail: enquiries@tannoy.com
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Our policy commits us to incorporating improvements to our products through continuous research and development. Please confirm current specifications for critical applications with your supplier.
18
1
9
NOTESNOTES
Loading...