TANDOOR WS-GFT-31-CE, WS-GFT-35-CUS-CE, WS-GFT-35-CE Installation And Operation Manual

Installation and
Operation Manual

TANDOOR - CE

Speciality Ovens

Gas-Fired, Round, Square, Octagonal,
Barrel European Models

TANDOOR 31" WS-GFT-31-CE

TANDOOR 35" WS-GFT-35-CE

BARREL TANDOOR WS-GFT-35-CUS-CE

WOOD STONE CORPORATION

1801 W. Bakerview Rd.

Bellingham, WA 98226 USA

Toll Free 800.988.8103

Tel [phone]

Fax [phone]

www.woodstone-corp.com

DOC NO M0054.05 REVISED April 2017

TABLE OF CONTENTS

Tandoor CE Installation
and Operation Manual

TABLE OF CONTENTS

TANDOOR

CAUTIONS AND WARNINGS

GFT-31-CE SPECIFICATIONS

GFT-35-CE SPECIFICATIONS

GFT-35-CUS-CE (BARREL) SPECS

CLEARANCES & VENTING

GAS SPECIFICATIONS

� � � � � � � � � � � � � � � � � � � � � � � � � �3

� � � � � � � � � � � � �4

� � � � � � � � � � � � �5

� � � � � � � � � � � � �6

� � � � � � � � �7

� � � � � � � � � � � � � � �8

� � � � � � � � � � � � � � � � � �9

LOWER FLASHING INSTALL (BARREL)

OPERATION

LIMITED WARRANTY

� � � � � � � � � � � � � � � � � � � � � � � �11

� � � � � � � � � � � � � � � � �14

� � � � �10

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 2 OF 16

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

TANDOOR CE

Tandoor CE Installation
and Operation Manual

INSTALLATION AND OPERATION MANUAL FOR THE

WOOD STONE TANDOOR

GAS-FIRED TANDOOR OVEN

WS-GFT-31 (ROUND, SQUARE AND OCTAGONAL),

WS-GFT-35 (ROUND, SQUARE, OCTAGONAL)

WS-GFT-35-CUS (BARREL)

CE MODELS

ADDITIONAL COPIES AVAILABLE UPON REQUEST

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

Square model (shown with
optional utensil rails, pan rail
w/ pans and shelf)

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

Barrel model

Round modelOctagonal model

E-MAIL [e-mail]

woodstone-corp.com

PG 3 OF 16

CAUTIONS & WARNINGS

Tandoor CE Installation
and Operation Manual

INSTALLATION AND OPERATING INSTRUCTIONS FOR THE WOOD STONE

GFT-31-(RND, SQR, OCT)-CE-(NG, LP), GFT-35-(RND, SQR, OCT, CUS)-CE-(NG, LP)

TANDOOR OVENS

RETAIN THIS MANUAL FOR FUTURE REFERENCE

Additional copies of this manual at woodstone-corp�com�

For prompt responses to service/maintenance questions, call your local distributor�

READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE

Please read this entire manual before you install the oven. Failure to follow instructions may result in property
damage, bodily injury or even death. Contact your local building or fire officials about restrictions and installation
inspection in your area.

It is recommended that this oven be installed, maintained and

serviced by authorized professionals.

IMPORTANT: Consult your local gas supplier for a statement outlining a procedure to be followed in the event you smell gas�
Post the statement in a prominent location�

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or
any other appliance. Also, always keep the area under and around this appliance free and clear of any and all
combustible materials.

WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property damage, injury
or death. Read the installation, operation and maintenance instructions thoroughly before installing or servicing this
equipment.

DO NOT THROW THIS MANUAL AWAY

Wood Stone's gas-fired Tandoor was tested and approved by Intertek Testing Services,

to the requirements of BS-EN 203-1:2014.

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 4 OF 16

0359-14

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

GFT-31-CE SPECIFICATIONS

G

G

30 3/4"
780mm

30 3/4"
780mm

O

12"
300mm

Open ing

O

12"
300mm

Opening

12 3/4"
320mm

G

G

G

30 3/4"
780mm

30 3/4"
780mm

30 3/4"
780mm

12"
300mm

Open ing

O

12"
300mm

Open ing

O

12"
300mm

Opening

12 3/4"
320mm

21 1/2"
550mm

21"
530mm

G

G

30 3/4"
780mm

O

12"
300mm

Opening

12 3/4"
320mm

G

30 3/4"
780mm

O

12"
300mm

Opening

12 3/4"
320mm

Tandoor CE Installation
and Operation Manual

WS-GFT-31 (ROUND, OCTAGONAL AND SQUARE MODELS)

Plan view (Round)

30 3/4"
780mm

12"

O

300mm

Open ing

Plan view (Square)

30 3/4"
780mm

Front view (Round)

Air intake: Do not
facade or cover over

G

37 3/4"
960mm

Shipping weight:
431 Kg
(750 lbs.)

31"
790mm

6 1/4"
160mm

Side view (Round)

21"
530mm

G

21 1/2"
550mm

Note: Side and front
view dimensions are
the same for the Round,
Square and Octagonal
models�

12"

O

300mm

Open ing

Plan view (Octagonal)

30 3/4"
780mm

G

O

12"
300mm

Opening

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

12 3/4"
320mm

UTILITY SPECIFICATIONS

Gas: 19mm (3/4") BPT gas inlet (female threaded)

See Gas Ratings in the GAS SPECIFICATIONS section of this manual�
Gas connection should be made using an approved flexible connector

and the unit must be restrained in accordance with all relevant local and
national codes� Gas connection is made beneath unit at rear�

Venting

This appliance must be installed under an exhaust hood, in accordance
with all relevant local and national codes, and in a manner acceptable to
the authority having jurisdiction�

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

PG 5 OF 16

GFT-35-CE SPECIFICATIONS

G

34 3/4"
880mm

O

13"
330mm

Opening

G

O

13"

34 3/4"
880mm

14 1/4"
360mm

G G

34 3/4"
880mm

O

13"
330mm

Opening

34 3/4"
880mm

G

O

13"
330mm

Opening

34 3/4"
880mm

14 1/4"
360mm

160mm

24 1/2"
620mm

24 3/4"
630mm

34 3/4"
880mm

O

13"
330mm

Opening

G

14 1/4"
360mm

34 3/4"
880mm

O

13"
330mm

Opening

34 3/4"
880mm

14 1/4"
360mm

Tandoor CE Installation
and Operation Manual

WS-GFT-35 (ROUND, OCTAGONAL AND SQUARE MODELS)

Plan view (Round)

34 3/4"
880mm

13"

O

330mm

Open ing

Plan view (Square)

Front view (Round)

Air intake: Do not
facade or cover over

G

40 3/4"
1040mm

33 3/4"
860mm

6 1/4"

Shipping weight:
431 kg
(950 lbs.)

Side view (Round)

24 3/4"
630mm

G

Note: Side and front
view dimensions are
the same for the Round,
Square and Octagonal
models�

24 1/2"
620mm

13"

O

330mm

Opening

Plan view (Octagonal)

34 3/4"
880mm

G

UTILITY SPECIFICATIONS

Gas: 19mm (3/4") BPT gas inlet (female threaded)

See Gas Ratings in the GAS SPECIFICATIONS section of this manual�
Gas connection should be made using an approved flexible connector and the unit

O

Opening

13"
330mm

14 1/4"
360mm

must be restrained in accordance with all relevant local and national codes� Gas
connection is made beneath unit at rear�

Venting

This appliance must be installed under an exhaust hood, in accordance with all
relevant local and national codes, and in a manner acceptable to the authority
having jurisdiction�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 6 OF 16

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

Plan view

G

36 1/2"
920mm

2"
50mm

14 3/4"
370mm

O

12"
300mm

Opening

35"
890mm

36 1/4"35 1/4"-

920mm900mm-

Height Adjustable

7"
180mm

GFT-35-CUS-CE (BARREL) SPECS

Tandoor CE Installation
and Operation Manual

WS-GFT-35-CUS (BARREL MODEL)

35"
890mm

G

12"

O

300mm

Opening

Air intake: Do not
facade or cover over

Shipping weight:
431 Kg
(750 lbs.)

Front view

21"
530mm

21 1/2"
550mm

Side view

7"
180mm

Height Adjustable

36 1/4"35 1/4"-

920mm900mm-

14 3/4"
370mm

G

16 1/4"

2"
50mm

36 1/2"
920mm

UTILITY SPECIFICATIONS

Gas: 19mm (3/4") BPT gas inlet (female threaded)

See Gas Ratings in the GAS SPECIFICATIONS section of this manual�
Gas connection should be made using an approved flexible connector and the unit must be restrained in accordance with all

relevant local and national codes� Gas connection is made beneath unit at rear�

Venting

This appliance must be installed under an exhaust hood, in accordance with all relevant local and national codes, and in a
manner acceptable to the authority having jurisdiction�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

PG 7 OF 16

CLEARANCES & VENTING

Tandoor CE Installation
and Operation Manual

WARNING: Do not pack required air space (clearance) with insulation or other materials. When non-

!

INSTALLATION CLEARANCES

The Wood Stone gas-fired Tandoor must be installed with at least 25mm
(1") side clearance to combustible construction� Install the unit on a
non-combustible floor, or one provided with a non-combustible covering
that extends at least 92mm (36") in all directions� Any combustible
construction above (overhanging) the appliance should be protected in
a manner acceptable to the authority having jurisdiction�

ENCLOSURES

If the appliance is enclosed, provisions should be made so that it can
easily be removed from the enclosure�

combustible building materials contact the body of the oven, the clearances to combustibles are
transferred to those non-combustibles.

Combustible construction overhanging
the appliance should be protected in
a manner acceptable to the authority
having jurisdiction.

Shaded area must be left unobstructed for
critical combustion air and easily accessible
for removal of the drip pan and operation
of the pilot safety valve. If this area must

25mm (1") side
clearance to
combustible
construction

be covered, the cover should be easily
removable and heavily perforated.

Install on a noncombustible floor, or one
protected in a manner acceptable to the
authority having jurisdiction, extending
92mm (36") in all directions.

VENTING

The Wood Stone gas-fired Tandoor must be installed under an appropriate grease rated exhaust hood� Refer to local and/or national
codes for hood specification requirements� The hood must be designed for the removal of the combustion products of gas, as well
as the cooking vapors related to the intended use of the oven� Make up air must be provided as necessary for the proper operation
of the ventilation system�

Some jurisdictions may require that the Tandoor be interlocked to the hood ventilation system to prevent operation of the appliance
when the ventilation system is not turned on� If an interlock is required, use an approved gas solenoid (supplied and installed by
others), wired so that the gas supply to the appliance is turned off whenever the ventilation system is turned off�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 8 OF 16

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

GAS SPECIFICATIONS

Tandoor CE Installation
and Operation Manual

GAS CONNECTION

The gas connection is made at the lower rear of the appliance� See next page for details�

This appliance is equipped with casters; it must be installed using the casters supplied with an approved gas connector/quick
disconnect device in accordance with all pertinent national and local regulations� It must also be installed with restraining means to
guard against transmission of strain to the connector�

IMPORTANT: The gas supply to this appliance should be equipped with an individual appliance shutoff valve that is capable
of completely isolating the appliance from the main gas supply� This valve should be installed in such a manner as to be readily
accessible to the operator of the appliance�

The Wood Stone gas-fired Tandoor is equipped with a 19mm (3/4") BPT female gas connection, located on the underside of the
rear of the unit� Anchor points for the restraining means are provided on the underside of the Tandoor; these are holes punched in
the rear portion of the drip/debris pan rails�

GAS RATINGS

Model WS-GFT-31 and WS-GFT-35
Input (kW)
Gas Group I

Inlet Pressure (mbar) 20 25 20 28-30/37 30/37/50 28-30/37 50
Gas Pressure at Valve Outlet

(mbar)

11�7 11�7 11�7 14�2 11�7 14�2 14�2

2H

I

2L

I

2E

I

3+

I

3P

I

3B/P

I

3B/P

10 10 10 25 25 25 25

THIS APPLIANCE IS NOT FOR USE WITH SOLID FUEL

GAS CODE LIMITATIONS

The installation of this appliance must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223�1, the Natural Gas installation Code CAN/CGA-B149�1 or the Propane Installation Code, CAN/CGA-B149�2, as
applicable�

The appliance and its individual shutoff valve (supplied by others) must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3�45 kPa)�

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve (supplied by others)
during any pressure testing of the gas supply piping system at test pressure, equal to or less than 1/2 psi (3�45 kPa)�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

PG 9 OF 16

LOWER FLASHING INSTALL (BARREL)

Tandoor CE Installation
and Operation Manual

DO NOT LOWER STRIP FLASHING UNTIL TANDOOR IS LOCATED IN ITS FINAL INSTALLED POSITION

Leveling the Tandoor

Position Tandoor in its final installed position�

With the Flashing still in the UP position, level

the Tandoor using the four adjustable feet�

Plumbing the Tandoor

If the gas connection is made below the Tandoor,

plumb before lowering the flange�

If the gas connection is not from below the

Tandoor,

it will be necessary to notch the flashing�

Screw holding up

flashing

•

•

• •

Ü

Center punch and

pre-drill using the

existing hole as a guide,

then fasten with screw

Protective black Edge Cover

•

•

• •

Ü

•

•

• •

Ü

This should be done after the flashing

is lowered�

Lowering the Flashing

The unit ships with the Strip Flashing secured into

its “UP” position with a screw at each leg�

Remove the screw from all 4 legs and lower the

flashing evenly around the Tandoor, flat to the floor�

Center punch and pre-drill each Leg using the

existing hole in the flashing as a guide�

Secure the flashing at each leg using the screw

previously removed�

Remove the protective black Edge Cover�

PG 10 OF 16

M0054.05 APRIL 2017

OPERATION

Tandoor CE Installation
and Operation Manual

PILOT LIGHTING PROCEDURE

Turn the Temperature Control Knob on the top of the unit to the OFF posiiton before attempting to light the pilot.

Turn the Gas Control Knob on the safety valve to the PILOT position.

1.

Push down on the Gas Control Knob and light the pilot immediately by pressing the red button of the spark igniter.

2.

Press the igniter every 2 seconds until a pilot flame is established� Hold the Gas Control Knob down for one full minute after
lighting the pilot�

3. Release the Gas Control Knob – the pilot flame should continue to burn. If the pilot flame does not remain lit, turn the

gas control valve to the OFF position, wait 5 minutes, and then repeat the steps above�

4. Once pilot is established, turn the Gas Control Knob on the safety valve (counterclockwise) from the PILOT to the
ON position. NOTE: failing to turn the gas control knob to the full ON position will reduce the flow of gas and could result in

poor ignition of the main burner�

5. Use the Temperature Control Knob on top of the Tandoor to control the height of the cooking flame. For Barrel
models, temperature control is located on the control box at the front end of the oven�

Plan view

Front view

Temperature
Control Knob

Drip/ debris pan

Gas Control Knob

FIRST FIRING

The first time the Tandoor is fired, the heat-up should be slow and steady� Hold the burner at a
very low flame (Temperature Control Knob set at “1” on models that are marked) for at least 8
hours with the lid on� Following this procedure will safely saturate the chamber with heat� You may
notice some small "crazing" cracks in the ceramic chamber after a few heat-ups and cool-downs�
Don't be alarmed as this is normal and will not affect the longevity or performance of the Tandoor�

Lid

Spark Igniter Button (Red)

Temperature Control Knob

First firing setting

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

PG 11 OF 16

DAILY OPERATION

DAILY OPERATION

Tandoor CE Installation
and Operation Manual

At the start of the day, the Tandoor will need to be heated
for approximately 60–90 minutes at full flame height with the lid on�
Set the Temperature Control Knob to its highest setting: 5.

Temperature
Control Knob

Heat-up setting

Once the chamber is at the desired temperature, typically 620 °F–650 °F, remove the lid completely for the cooking
day� Temperature can be determined using the optional Fluke Hand Held IR Thermometer (see the Tools and
Accessories section of the Wood Stone website)�

Set the Temperature Control Knob to the cooking temperature range:

1.3–1.5

� This should maintain a good cooking temperature for breads
and proteins� The Temperature Control Knob can be adjusted the
appropriate heat setting, depending on cooking style� Note that settings

Temperature
Control Knob

Typical cooking
flame setting

may also vary slightly depending on gas type (NG or LP)�

Heat is managed exclusively through the use of the Temperature Control Knob.

Do not operate the unit with the lid on, except during heat-up or overnight.

Partially covering the opening with the lid while cooking will damage the top of the Tandoor.

Heat damage caused by operating the Tandoor with the lid partially on

will not be covered by the warranty.

The use of ceramic briquettes, or seasoning the chamber, is unnecessary and will void the warranty.

SKEWER INDEX RING

The Tandoor comes standard with a stainless steel Skewer Indexing
Ring� It sits atop the opening with the tabs facing down� With the ring
in place, skewer spacing and orientation can be easily maintained� The
ring can be removed if you like when preparing Naan bread�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 12 OF 16

Skewer Index Ring

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

CLEANING & MAINTENANCE

Tandoor CE Installation
and Operation Manual

CLEANING

Debris that falls in the Tandoor will accumulate in the bottom of the chamber� Push the debris towards the center and under the
circular flame deflector, using the supplied Tandoor Naan Hook, where it will fall into the drip/debris pan under the unit� This pan
should be checked daily and emptied as necessary�

To remove debris from the chamber walls, first brush the walls with the optional In-Line Floor Brush (see the Tools and
Accessories section of the Wood Stone website)� Use a moist towel (water only) to swirl around the chamber� Any debris which
falls to the bottom of the chamber can be removed as described above�

The stainless cabinet and granite top of the unit should be cleaned as necessary, using a mild detergent and a nonabrasive
scouring pad�

TIP: Watch Wood Stone’s Tandoor-related videos for additional helpful information� Visit the Resource Center/Videos section of the
Wood Stone website�

Note: Some discoloration of the stone may occur.

This normal discoloration is only cosmetic and does not harm the unit.

MAINTENANCE

It is normal over time that the silicon joints will need to be renewed with a high temperature NSF approved silicone such as
Dow 732 or similar� This product can be obtained locally or ordered through the Wood Stone Service Department� Call your local
distributor�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

PG 13 OF 16

LIMITED WARRANTY

Tandoor CE Installation
and Operation Manual

WOOD STONE WARRANTS ITS EQUIPMENT TO THE ORIGINAL PURCHASER AGAINST DEFECTS IN

MATERIAL OR MANUFACTURE FOR A PERIOD OF ONE YEAR FROM THE ORIGINAL DATE OF PURCHASE,

SUBJECT TO THE FOLLOWING EXCLUSIONS AND LIMITATIONS.

CONTACT YOUR LOCAL DISTRIBUTOR FOR WARRANTY SERVICE

EXCLUSIONS

The warranties provided by Wood Stone do not apply in the following instances:
1� In the event that the equipment is improperly installed� Proper installation is the responsibility of the installer; proper installation

procedures are prescribed by the Wood Stone Installation and Operation Manual�

2� In the event the equipment is improperly or inadequately maintained� Proper maintenance is the responsibility of the user;

proper maintenance procedures are prescribed in the Wood Stone Installation and Operation Manual� Burner problems
resulting from debris or ash in the burner well will not be covered by the warranty� Call with questions regarding maintenance
frequency�

3� In the event that the failure or malfunction of the appliance or any part thereof is caused by abnormal or improper use or is

otherwise not attributable to defect in material or manufacture�
4� In the event that the appliance, by whatever cause, has been materially altered from the condition in which it left the factory�
5� In the event that the rating plate has been removed, altered or obliterated�
6� On parts that would be normally worn or replaced under normal conditions�
7� Normal cracking due to expansion and contraction stress relief in the ceramic firebox�
8� In wood-fired equipment configurations, in the event that pressed log products of any type have been burned in the equipment�
9� In coal-fired oven configurations, in the event any type of coal other than anthracite coal fuel has been used�
10� Damage resulting from the use of chemical cleaning products in the oven, as well as any damage from liquids or chemicals,

including water, being poured or sprayed into the oven�

If any oral statements have been made regarding this appliance, such statements do not constitute warranties and are not part of
the contract of sale� This Limited Warranty constitutes the complete, final and exclusive statement with regard to warranties�

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE OR WARRANTY AGAINST LATENT DEFECTS

LIMITATIONS OF LIABILITY

In the event of warranty claim or otherwise, the sole obligation of Wood Stone shall be the repair and/or replacement, at the
option of Wood Stone, of the appliance or component or part thereof� Such repair or replacement shall be at the expense of Wood
Stone with the exception of travel over 100 miles or two hours, overtime, and holiday charges which shall be at the expense
of the purchaser� Any repair or replacement under this warranty does not constitute an extension of the original warranty for
any period of the appliance or for any component or part thereof� Parts to be replaced under this warranty will be repaired or
replaced at the option of Wood Stone with new or functionally operative parts� The liability of Wood Stone on any claim of any
kind, including claims based on warranty, expressed or implied, contract, negligence, strict liability or any other theories shall be
solely and exclusively the repair or replacement of the product as stated herein, and such liability shall not include, and purchaser
specifically renounces any rights to recover, special, incidental, consequential or other damages of any kind whatsoever,
including, but not limited to, injuries to persons or damage to property, loss of profits or anticipated profits, or loss of use of the
product�

TO SECURE WARRANTY SERVICE:

Contact your local distributor�

M0054.05 APRIL 2017

An ongoing program of product improvement may
require us to change specifications without notice.

PG 14 OF 16

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TEL [phone]
FAX [phone]

E-MAIL [e-mail]

woodstone-corp.com

M0054.05 APRIL 2017

PG 15 OF 16

WOOD STONE CORPORATION

1801 W. Bakerview Rd.

Bellingham, WA 98226 USA

Tel [phone]

Fax [phone]

www.woodstone-corp.com

An ongoing program of product improvement may
require us to change specifications without notice.

PG 16 OF 16

M0054.05 APRIL 2017