Tanaka TPE-2501, TPE-270PF-PN, TPE-2510, TPE-25OPF User Manual

Owner’Owner’

Owner’

Owner’Owner’

s Mans Man

s Man

s Mans Man

ualual

ual

ualual

Model Numbers:

TPE-2501,TPE-2510TPE-2501,TPE-2510

TPE-2501,TPE-2510

TPE-2501,TPE-2510TPE-2501,TPE-2510
TPE-250PFTPE-250PF

TPE-250PF

TPE-250PFTPE-250PF

POLE EDGERSPOLE EDGERS

POLE EDGERS

POLE EDGERSPOLE EDGERS

,TPE-270PF/PN,TPE-270PF/PN

,TPE-270PF/PN

,TPE-270PF/PN,TPE-270PF/PN

P/N 28575
Date 02-27-01

TPE-2510

TPE-270PF

ISM, Inc. • 1028 4th Street SW • Auburn, WA 98001 • Phone: [phone] • Fax: [phone]

www.tanakapowerequipment.com [e-mail]

Supplier To The Outdoor Power Equipment Industry

t

TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF

Owner’s Manual

Before using this unit:

• Read the operator’s manual carefully.

• Check that the cutting equipment is correctly assembled

and adjusted.

• Start the unit and check the carburetor adjustment.

See “Maintenance”.

Always wear eye, head and ear
protectors when using this unit.

WARNING

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects and other reproductive harm.

Read, understand and follow all
warnings and instructions in this
manual and on the unit.

Keep all children, bystanders and helpers 15m
(50ft.) away from the unit. If anyone
approaches you, stop the engine and cutting
attachment immediately.

It is important that you read, fully understand and
observe the following safety precautions and
warnings. Careless or improper use of the uni
may cause serious or fatal injury.

www.tanaka-usa.com 1 [e-mail]

TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF

Owner’s Manual

1. What is What?

Since this manual covers several models, there may be some difference between pictures and your
unit. Use the instructions that apply to your unit.

1. Fuel Cap

2. Throttle Trigger

3. Starter Handle

4. Blade guard

5. Blade

6. Drive shaft pipe

7. Loop handle

8. Spark plug

9. Ignition Switch

10. Depth guide wheel

11. Lock Button

12. Knob nut

13. Choke lever

www.tanaka-usa.com 2 [e-mail]

TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF

2. Warnings and safety instructions

Operator safety

• Always wear a safety face shield or goggles.

• Always wear heavy, long pants, boots and gloves. Do

not wear loose clothing, jewelry, short pants, sandals
or go barefoot. Secure hair so it is above shoulder
length.

• Do not operate that tool when you are tired, ill or

under the influence of alcohol, drugs or medication.

• Never let a child or inexperienced person operate the

machine.

• Wear hearing protection.

• Never start or run the engine inside a closed room or

building. Breathing exhaust fumes can kill.

• Keep handles free of oil and fuel.

• Keep hands away from cutting equipment.

• Do not grab or hold the unit by the cutting

equipment.

• When the unit is turned off, make sure the cutting

attachment has stopped before the unit is set down.

• When operation is prolonged, take a break from time

to time so that you may avoid possible white finger
disease which is caused by vibration.

Tool safety

• Inspect the entire tool before each use. Replace

damaged parts. Check for fuel leaks and make sure
all fasteners are in place and securely fastened.

• Replace parts that are cracked, chipped or damaged

in any way before using the tool.

• Make sure the safety guard is properly attached.

• Keep others away when making carburetor

adjustments.

• Use only accessories as recommended for this tools

by the manufacturer.

WARNING!

Never modify the tool in any way. Do not use your cutting tool
for any job except that for which it is intended.

Fuel safety
NOTE!

• Empty the fuel tank before storing the tool.

Especially, in case of over three month storage,
it is a must otherwise fuel may corrode causing
carburetor damage. It is recommended that
the fuel be emptied after each use. If fuel is
left in the tank, store so fuel will not leak.

• Mix and pour fuel outdoors and where there are no

sparks or flames.

• Use a container approved for fuel.

• Do not smoke or allow smoking near fuel or the tool

or while using the tool.

• Wipe up all fuel spills before starting engine.

• Move at least 3 m (10ft.) away from fueling site

before starting engine.

• Stop engine before removing fuel cap.

• Empty the fuel tank before storing the tool. It is

recommended that the fuel be emptied after each
use. If fuel is left in the tank, store so fuel will not
leak.

• Store tool and fuel in area where fuel vapors cannot

reach sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.

WARNING!

Anti-vibration systems do not guarantee that you will not
sustain white finger disease or carpel tunnel syndrome.
Therefore, continual and regular users should monitor closely
the condition of their hands and fingers. If any of the above
symptoms appear, seek medical advice immediately.

Cutting safety

• Inspect the area to be cut before each use. Remove

objects which can be thrown or become entangled.

• For respiratory protection, wear an aerosol protection

mask when cutting the grass after insecticide is
scattered.

• Keep others including children, animals, bystanders

and helpers outside the 15 m hazard zone. Stop the
engine immediately if you are approached.

• Always keep the engine on the right side of your

body.

• Hold the tool firmly with both hands.

• Keep firm footing and balance. Do not over-reach.

• Keep all parts of your body away from the muffler

and cutting attachment when the engine is running.

• Keep cutting attachment below waist level.

Maintenance safety

• Maintain the tool according to recommended

procedures.

• Disconnect the spark plug before performing

maintenance except for carburetor adjustments.

• Keep others away when making carburetor

adjustments.

• Use only genuine replacement parts as recommended

by the manufacturer.

Transport and storage

• Carry the tool by hand with the engine stopped and

the muffler away from your body.

• Allow the engine to cool, empty the fuel tank, and

secure the tool before storing or transporting in a
vehicle.

• Empty the fuel tank before storing the tool. It is

recommended that the fuel be emptied after each
use. If fuel is left in the tank, store so fuel will not
leak.

• Store tool out of the reach of children.

• Clean the unit carefully and store it in a dry place.

• Make sure engine switch is off when transporting or

storing.

• When transporting in a vehicle, cover blade with

blade cover.
If situations occur which are not covered in this manual, take
care and have a good judgment. Contact your dealer if you
need assistance.
Pay special attention to statements preceded by the following
words:

WARNING!

Indicates a strong possibility of severe personal injury or loss
of life, if instructions are not followed.

CAUTION!

Indicates a possibility of personal injury or equipment damage,
if instructions are not followed.

NOTE!

Helpful information for correct function and use.

Owner’s Manual

www.tanaka-usa.com 3 [e-mail]