Tanaka 746280 User Manual

PROFESSIONAL CUTTING HEADS

Owner’s Manual

(#29592 - Page 1)

FIXED LINE

ITEM NUMBER

746280

Aluminum

Cutting Heads

Safety Instructions

1.) *Warning! Read this owners manual as well as

the owners manual supplied with your grass trimmer.
Be sure to follow all warnings and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.

2.) Wear eye protection that complies with ANSI
Z87-1 standard.

3.) Do not operate this or any type of power
equipment when you are tired, ill, or under the
influence of alcohol, drugs, or medication.

4.) Always wear heavy long pants, boots, and
gloves. Do not wear loose clothing, short pants,
sandals, or go bare foot. Secure hair so it is above
shoulder level.

5.) Inspect unit before each use. Replace parts that
may be cracked, chipped, or damaged in any way .
Make sure the cutting head is properly installed and
securely fastened. Be sure the cutting attachment
shield is properly attached in the position recom­mended by the manufacturer.

MANUAL FEED

ITEM NUMBER

746290

Installation (continued)

This shoulder is necessary to mount these heads
securely and in the proper position. The diameter of
many mounting shoulders is 1” (25.4mm) and
heads require this size. For mounting shoulder diam­eters that are .79” (20mm), a special shim is included
in the package contents to provide the necessary
spacing.

A variety of adapters are provided to accommodate
mounting to Tanaka as well as other units (see
sizes listed below). To mount the “Fixed Line”
head, (Ref. 1), place the recessed side on to the
mounting shoulder of the gear case. When using
the 8mm nut, always use the 10mm washer.

The “Manual Feed” head
is mounted in the same

Ref. 2A

manner , except that the
“Cutter Holder” (Ref. 2-4
show below) must always
be used as shown in Ref.
2A & 2B.

Ref. 1

Ref. 2B

both

6.) Clear the work area before each use. Remove
all objects such as rocks, broken glass, nails, wire,
or string which can be thrown or become entangled
in the cutting head. Clear the area of children,
bystanders, and pets in a 50 foot (15m) radius. It is
recommended that bystanders wear eye protection.
If you are approached, stop the engine and cutting

Aluminum Cutting Head Mounting Hardware

746280 / Fixed Line 746290 / Manual Feed

1-1

1-2

2-1

attachment immediately.

Installation

The Aluminum Cutting Heads
are designed for use on

straight shaft Grass Trim­mers and they are mounted to

the unit in the same manner.
T ypically, the gear case has a
separate piece or cover which
includes a mounting shoulder

WARNING!

These heads are

NOT RECOMMENDED

for use on units without a

mounting shoulder

1-3

Ref.# Part No. Description

1-2 312-33386-20

1-3 313-38100-20

1-4 27288

1-5 992-01100-011 Washer (10mm)

Adapter Bolt

(8mm x 1.25 LHM)

Adapter Nu t

(10mm x 1.25 LHF)

Mounting Shim

(20mm to 1")

1-4

2-3

Ref.# Part No. Description

2-1 312-33386-20

2-2 313-38100-20

2-3 27288
2-4 311-37300-203 Cutter Holder

on which blades are held and
centered.

ISM, Inc. • 1028 4th St. SW • Auburn, WA 98001 • Phone: [phone] • Fax: [phone] • www.tanakapowerequipment.com

2-2

2-4

Adapter Bolt

(8mm x 1.25 LHM)

Adapter Nut

(10mm x 1.25 LHF)

Mounting Shim

(20mm to 1")

PROFESSIONAL CUTTING HEADS

Aluminum Cutting Heads

Nylon Line Replacement

FIXED LINE

ITEM NUMBER

746280

1.) This head is designed to accommodate nylon

line with a diameter of .095” - .130”. The pre-cut
lengths included in the package are 14” which will
provide a total cutting swath diameter of approxi­mately 13”. However this length can be longer (or
shorter) depending on the following factors:

A. The diameter of line being used
B. The unit’s power
C. The desired cutting speed
D. The desired total cutting swath diameter.

2.) Fold a pre-cut length of line in half.

3.) On the gear case facing side of the head, insert

the two ends of the folded line in to the two holes
(just above the Tanaka logo) and pull them com­pletely through the underside evenly .

Owner’s Manual

(#29592 - Page 2)

MANUAL FEED

ITEM NUMBER

746290

1.) This head is designed to accommodate nylon

line with a diameter of .095” - .105” and can hold up
15’ (total length). The cutting swath (determined by
the length of the line exiting the head from each
side) is variable depending on the following:

A. The diameter of line being used
B. The unit’s power
C. The desired cutting speed

2.) Fold a pre-cut length of line with one side slightly
longer than the other (as shown below).

3.) On the ground facing side of the head, insert the
two ends of the folded line in to the two holes and
pull them completely through (as shown below).

4.) Wind

both lengths of line together in either
direction until 8-10” remain. Insert the shortest line
into the nearest exit hole slot then wind the
remaining line to the slot on the opposite side. More

4.) From the opposite side of the head, feed the
lines through the holes located on the side of the
head and pull until they are totally extended

line can be extended (in increments of 3”) by
unwinding both lines to next exit hole. The total line
length (to extend from each side) will be subject to
the factors listed above, however a good starting
length could be 6”.

TANAKA OFFERS OTHER HIGH QU ALITY CUTTING HEADS

Fully Automatic

The Original

BRAIN

Order # 746251
Std. Line Diameter: .095”
Line Capacity: 30ft. / 9.1m

ISM, Inc. • 1028 4th St. SW • Auburn, WA 98001 • Phone: [phone] • Fax: [phone] • www.tanakapowerequipment.com

®

The BRAIN

2000

Order # 746751
Std. Line Diameter: .095”
Line Capacity: 20 ft./ 6.7m

®

Semi- Automatic

Order # 746451
Std. Line Diameter: .095”
Line Capacity: 25 ft. / 7.6m

Manual Feed

Order # 746551
Std. Line Diameter: .095”
Line Capacity: 25ft / 7.6 m