Operation Manual
Preliminary Version
OSPREY G3 series
KVM xx50W / xx51W
24558 Henstedt-Ulzburg | Germany | ..49 - (0)700 - TAMUZLCD [82 689 523]
All rights reserved. No part of this work may be reproduced or duplicated or spread or processed under
use of electronic systems, in any form (print, photocopy, microfilm or other proceedings), without written
permission of the right owner.
Alle Rechte vorbehalten. Kein Teil dieses Werkes darf in irgendeiner Form (Druck, Fotokopie, Mikrofilm
oder anderen Verfahren) ohne schriftliche Genehmigung des Rechteinhabers reproduziert oder unter
Verwendung elektronischer Systeme verarbeitet, vervielfältigt oder verbreitet werden.
Concept, Publishing and Production: E.L.B.E medi@, Henstedt-Ulzburg
Printed in Germany
I. Issue OSPREY G3 Series Digital Broadcast Monitor
valid for Firmware Release 2.05 and above
© 2014 Copyright by:
TAMUZ Broadcast Monitors
+49 - (0)700 TAMUZLCD [82 689 523]
eMail: info@tamuz.tv
www.tamuz.tv
Rights reserved to change specifications and design without notice
Technische und farbliche Änderungen vorbehalten
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 2 -
OSPREY G3 Series Digital Broadcast Monitor
Table of Content
Introduction...................................................................4
Digital Broadcast Monitor............................................4
OSPREY G3 series models...........................................5
ISO Product Quality....................................................6
Pixel Errors..............................................................6
Class of Usability.....................................................6
Class of Reflections..................................................7
General Safety Instructions.............................................8
Limitation of the product..............................................8
Duty of care of the user...............................................8
Safety symbols............................................................8
Basic Safety Instructions...............................................9
Service and Maintenance.........................................9
Observe environmental protection prescriptions.........9
Recycling..................................................................10
Recognition of the copyrights.....................................10
Guarantee agreement:.................................................11
Guarantee period..................................................11
Guarantee exceptions............................................11
Guarantee Certification..........................................11
Warranty Card.............................................................12
Transport of the equipment...........................................13
Transportation..........................................................13
Weight..................................................................13
Packing....................................................................13
Return dispatch......................................................13
Damages in transit................................................13
Conformity Declaration................................................14
Technical Data............................................................15
System Hardware......................................................15
Features......................................................................16
OSPREY G3 series.....................................................16
Image Display Functions and Measurement.............17
Controls and their Functions.........................................21
Front Panel...............................................................21
Rear Panel................................................................23
OSD Menu..................................................................24
Menu structure..........................................................24
Top- and Sub-Menus.............................................24
Menu Operation.......................................................25
Menu Item Description..............................................26
Picture..................................................................26
Image Adjustment..................................................26
Setup....................................................................27
Audio...................................................................29
PIP/PBP.................................................................29
System Status........................................................30
Factory Reset............................................................31
Remote Control............................................................32
Hardware connection................................................32
Software Configuration.............................................32
Communications test.................................................32
Commands...........................................................33
Stand Installation Instruction ........................................34
Block Diagrams...........................................................36
Blockdiagramm TFT Panels.................................36
Safety Notice...............................................................37
Remarques de sécurité.................................................38
Indicaciones de seguridad............................................39
Instruções de segurança...............................................40
Norme di sicurezza......................................................41
Sikkerhedsanvisninger..................................................42
Säkerhetsinformationer................................................43
Turvallisuusohjeet........................................................44
Sikkerhetsanvisninger...................................................45
Öryggisleiðbeiningar....................................................46
Veiligheidsvoorschriften................................................47
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 3 -
Introduction OSPREY G3 Series
Introduction
Digital Broadcast Monitor
The TAMUZ OSPREY G3 series monitors are our range of cost effective Digital Video Control Monitors
for SD and HD Broadcast and Production Applications in various screen sizes starting from 7“wide up to
to 24“ wide.
The OSPREY series monitors are designed as an universal digital control monitor, equipped with analog,
DVI/HDMI and SDI inputs, to display HD studio signals directly. They are an ideal solution for viewing
the output of Cameras, Switchers or other Broadcast Equipment for confidence or quality. This monitors
are available as desktop or rack mountable devices.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 4 -
Introduction OSPREY G3 Series
OSPREY G3 series models
The signal processor contains a set of micro computer controlled DSP's and scalers with native serial capability. Various models are available within series.
Model Screen Size Freq-V Hz Aspect Ratio Screen Resolutions SDI DVI/HDMI Analog
KVM 7050W 7“ 50 - 60 15 : 9 1024 x 600 2x 1x 3x
KVM 9050W 8.9“ 50 - 60 15 : 9 1280 x 768 2x 1x 3x
KVM 1730W 17“ 50 - 60 16 : 9 1366 x 768 2x 1x 3x
KVM 1750W 17“ 50 - 60 16 : 9 1920 x 1080 2x 1x 3x
KVM 1751W 17“ 50 - 60 16 : 9 1366 x 768 2x 1x 3x
KVM 1930W 19“ 50 - 60 16 : 9 1366 x 768 2x 1x 3x
KVM 2250W 21“ 50 - 60 16 : 9 1920 x 1080 2x 1x 3x
KVM 2350W 22.5“ 50 - 60 16 : 9 1920 x 1080 2x 1x 3x
KVM 2450W 24“ 50 - 60 16 : 10 1920 x 1200 2x 1x 3x
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 5 -
Introduction OSPREY G3 Series
ISO Product Quality
For the production of TAMUZ video monitors LCD panels complies with the standard ISO 13406-2, error-class 1 or 2, only. This ISO standard 13406-2 defines the scales for ergonomic and picture quality.
The LCD panel manufactures itself (like AU, CMO, LG-Philips, NEC, Samsung, Sharp or Toshiba) don't
guarantees absolute any errorlessness and don't guarantees that the LCD panels are free of sticking effects.
Pixel Errors
Following limited values which may not exceed are valid.
ISO 13406-2 Typ 1 Typ 2 Typ 3 max. Distance connected Defects
Class I 0 0 0
Class II 2 2 5
1 defect pixel within a circle of 5 mmmaximum 2 defective sub-pixel
beside each other
Class III 5 15 50
2 defect pixels within a circle of 5 mmmaximum 2 defective sub-pixel
beside each other
Class IV 50 150 500
Error-type #1 describes errors by a complete bright (white) pixel, error-type #2 describes errors by a
complete dark (black) pixel, error-type #3 describes errors by defective sub-pixels of the colors red,
green and blue, which are completely bright or dark.
A single LCD pixel is built by a set of three sub-pixels, one of red, green and blue.
Error class I contains highly selected panels with no pixel error anyway. Panels within this class are rare
and very high priced. Panels from the error class II are the most common selection for high quality industry applications. The error class III defines the mass production selection for IT applications. TFT panels
related to the error class IV are not useful for a LCD monitor at all.
Class of Usability
Next the standard ISO 13406-2 defines the classification of usability of LCD screens.
Usability Classification Description
Class 1 This permits several users to view the entire display area at the same time. This ap-
plies for intended viewing distance (between 40 to 60 cm, depending on the size
and resolution of the monitor) and for a viewing angle within an 80° cone in front
of the screen without any restriction of visual efficiency, in such a way that brightness, contrast and color is maintained
Class 2 Permits a single user to view the entire area of the display. This applies for inten-
ded viewing distance (between 40 to 60 cm, depending on the size and resolution
of the monitor) from every position in front of the screen, in such a way that brightness, contrast and color is maintained.
Class 3 Permits a single user to view the entire area of the display. This applies for inten-
ded viewing distance (between 40 to 60 cm, depending on the size and resolution
of the monitor) from one fixed position in front of the screen, in such a way that
brightness, contrast and color is maintained.
Class 4 Permits a single user to view the center area of the display. This applies for inten-
ded viewing distance (between 40 to 60 cm, depending on the size and resolution
of the monitor) from one fixed position in front of the screen, in such a way that
brightness, contrast and color is maintained.
All of the TAMUZ OSPREY series monitors comply with class 1.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 6 -
Introduction OSPREY G3 Series
Class of Reflections
The reflection characteristics of an LCD Screen are of particular importance in very bright ambient conditions or in an environment with multiple light sources. The ISO standard provides for three quality classes.
Reflection Classification Description
Class 1 General office conditions without special requirements as to workspace lighting.
Class 2 Appropriate for most office conditions, with few exceptions.
Class 3 Appropriate for office environments, with controlled luminance conditions.
All of the TAMUZ OSPREY series monitors comply with class 1.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 7 -
General Safety Instructions OSPREY G3 Series
General Safety Instructions
Limitation of the product
The technology itself and some parts built-in the TAMUZ OSPREY G3 series have limitations which the
user have to understand and accept.
The user must accept that it is necessary
•
to avoid condensation of water within the OSPREY G3 series. It may result in improper
operation or disconnection of electrodes.
•
not to exceed the absolute maximum rating value. (input voltage variation, environmental
temperature and so on) Otherwise the receiver may be damaged.
•
the antenna must be grounded correctly. Please observe the relevant regulations.
Duty of care of the user
The OSPREY G3 series was designed and built under the harmonized norms to be adhered as well as
further technical specifications. It corresponds to the state of the art and ensures a maximum amount of
safety.
However, this safety can only be reached, if all safety measures are taken in the operational practice. It is
the duty of the OSPREY G3 series user, to plan these measures and check their explanation.
The user must guarantee that
•
the OSPREY G3 series is only used as agreed (cf. chapter product specification)
•
the OSPREY G3 series is operated only in faultless, working condition and particularly the
safety facilities are checked for their function efficiency regularly
•
the OSPREY G3 series operator's manual always be placed in a complete and legible
condition for disposal
•
only sufficiently qualified and authorized staff operates, maintains and repairs the OSPREY
G3 series
•
staff is instructed to meet work safety and environmental protection regulation and knows the
operator's manual as well as there particularly contained safety instructions
•
all appropriate safety and warning notes not being removed and remaining legible at the
OSPREY G3 series
Constructive changes at the OSPREY G3 series may be carried out only after written permission by the
manufacturer!
Safety symbols
The following safety symbols are applied in this operator's manual. These symbols shall primarily draw
the attention of the reader to the text of the accompanying safety note.
This symbol points out that there are dangers for life and health of
persons.
This symbol indicates information which contributes for a better
understanding of the function of the equipment.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 8 -
General Safety Instructions OSPREY G3 Series
This symbol points out that there are dangers for material and
environment or the equipment himself.
Warning about dangerous electrical voltages to or within the
equipment.
Basic Safety Instructions
The OSPREY G3 series only may be used by persons who are trained, authorized and has knowledge of
the operator's manual.
Before every production, check the OSPREY G3 series for visible damages and make sure that it is ope-
rated in faultless condition! Report noticed deficiencies to the supervisor immediately or schedule to restore by qualified persons.
Service and Maintenance
Adhere to the specified inspection and maintenance intervals in the operator's manual!
•
Before maintenance and repair work it must be guaranteed that all parts of the OSPREY G3
series have cooled down on space temperature!
•
Smear-, cool- or cleaning-fluids, endangering the environment, must be disposed duly!
•
Repair work on the electrical power supply of the OSPREY G3 series system must be done by
a trained electric qualified employee!
•
Damaged lines or cables have to be immediately replaced!
Released bolted joints must be checked for solid seat before putting into operation after maintenance or
repair work and it must be guaranteed, that removed system-unit cover parts or filters were re-installed!
Observe environmental protection prescriptions
The legal duties for waste avoidance and proper utilization for elimination must be adhered at all work
stations, also including the OSPREY G3.
During repair, installation and maintenance work, be aware of water endangering substances such as;
•
Lubricating greases and oil
•
Hydraulics oils
•
Coolant
•
solvent containing cleaning liquids
don't load the floor or reach into the sewage system!
Note: The valid environmental protection prescriptions must be observed.
These water endangering substances must be kept, transported, caught and disposed in suitable containers!
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 9 -
General Safety Instructions OSPREY G3 Series
Recycling
If OSPREY G3 series monitor no longer operates or is un-repairable, please do not dispose the receiver
in the trash.
Please return the receiver to your local dealer or TAMUZ directly, we will grant the correct and suitable
recycling of the old monitor.
Note: Don't waste unused, old or broken monitors. Follow your local environmental protection
prescriptions.
Recognition of the copyrights
The user of the OSPREY G3 series appreciates, that in the OSPREY G3 series contains software programs as well as this documentation is subject to the copyright laws as well as copyright propriety and
other protection rights and does not purchase this with the acquisition or the use of the OSPREY G3 se-
ries system by any time. The user obtains rather merely the right for the exclusive use of the OSPREY G3
series.
In the OSPREY G3 series contained software as well as the accompanying documentation may not be
changed, enlarged or adapted to other systems or translated into other languages, without written permission of the author. With the installation and use of the OSPREY G3 series the user recognizes these license and use conditions.
Note: The OSPREY G3 series system contains copyright protected software and
documentation's.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 10 -
Guarantee agreement: OSPREY G3 Series
Guarantee agreement:
In the OSPREY G3 series system contains software and the instructions are left to the user as they are.
This means, the author of the software or the instructions doesn't assume any liability for the suitability of
the software or the documentation to any special purpose. He particularly isn't liable for damages or sequential damages which indirectly deliberately or unintentionally arise from the use of the OSPREY G3
series or the documentation directly.
The OSPREY G3 series system and the documentation can be changed and enlarged without previous
announcement at any time. Rights for updates free of charge does not apply.
Guarantee period
TAMUZ Monitors, the manufacturer of the OSPREY G3 series grants a guarantee period of 24 months
on the faultless function of the system and its components.
Guarantee exceptions
Claims for defects shall not exist in cases of
•
natural wear and tear and damages, defects, reduced output, and changes of condition or
operation of our product due to extraneous cause (for example impact, blows, agitation, water,
fire), improper storage, treatment or erection, unusual climatic conditions, special conditions at
receipt or operational conditions at the location of use, or force majeure;
•
defects due to construction and material deficiencies, as far as the customer has specified the
construction or the material.
•
Image Sticking on LCD-Panel, which is caused by permanent pictures as well as Gap Mura on the
LCD-Panel.
Guarantee Certification
Please, send in the full guarantee certification upon receipt of the product to the manufacturer or suppliers within 21 working days. The manufacturer or supplier only then can grant possible rights to claim
under guarantee in full size and transmitting current information about software updates and indications
for expansions or for the operation of the equipment to you.
Note: Only if the guarantee card of the OSPREY G3 series has been returned intime to the
manufacturer or supplier, rights to claim under guarantee can be asserted against the
manufacturer or supplier.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 11 -
Warranty Card OSPREY G3 Series
Warranty Card
To come in the position to reclaim your warranty rights, send in this warranty card within 21 days to the
manufacturer (TAMUZ Monitors, Germany) or your local dealer. Check the web site www tamuz.tv, www
tamuz.de or www tamuz.us for the correct address.
Garantie Registrierungskarte - Warranty Registration Card
Model:
TAMUZ OSPREY G3
Type:
Seriennummer: Serial Number:
Dieses Gerät wurde gekauft bei: - The Unit was purchased from:
Händler:
Ort.
Land:
Dealer:
City:
Country:
Verkaufsdatum: Purchase Date:
Dieses Gerät wurde gekauft von: - The Unit was purchased by:
Kunde: Customer:
Ansprechpartner: Contact Person:
Firma: Company:
Strasse: Street:
PLZ: Zip Code:
Ort: City:
Land: Country:
Telefon: Phone:
Telefax: Fax:
Email: Email:
Dieses Gerät wird eingesetzt im: - This Unit will be used at:
Regieraum: Control Room:
Schaltraum: Distribution:
Studio: Studio:
Ü-Wagen: OB-Truck:
Kopieranlage: VTR-Dubbing:
Schnittplatz: Editing:
Sprecher-Raum: Off-Room:
Andere: Other:
Unser Bestreben ist es, unsere Produkte kundengerecht zu entwickeln und fertigen. Wir sind Ihnen dankbar, wenn Sie sich Zeit
für Anregungen oder Kommentare nehmen:
Our mutual interest is, to design and manufacture practical products. We appreciate you taking the time to note your informati-
on and comments you may have.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 12 -
Transport of the equipment OSPREY G3 Series
Transport of the equipment
Transportation
The OSPREY G3 series is a sensitive electronic product and should be transported with all caution. Throwing the equipment or hard pushes during the transport must be avoided.
Weight
The OSPREY G3 series weights inclusive of the accessories and his packing less then 10 kg and should
be carried under consideration of the accident prevention measures or transported with help of corresponding aids therefore by two persons.
Note: Observe the accident prevention prescriptions at the transport of the OSPREY G3 series
to the avoidance of persons and damages to property.
Packing
The OSPREY G3 series is delivered in a special transport carton. It recommends itself to keep this carton
and the accompanying packaging. So in the case of a later necessary transport and dispatch the equipment can be packed and protect against damages as delivered to you.
Return dispatch
At a return dispatch without original packing to the supplier or manufacturer the liability is excluded.
Don't forget to ask for a RMA (return material authorization) number before you send any material back
to the manufacturer. Check for a RMA the web-site www.tamuz.tv, www.tamuz.de or www.tamuz.us.
Damages in transit
Check the contents of the received transport carton with the delivery note or the invoice on completeness
and inform your supplier if you have missing parts upon receipt of the product. Please contact within 5
working days. If you receive a delivery on which the transport carton or the contents is damaged, proceed after the known guidelines of the cargo shipper, (which as a rule is enclosed with the delivering papers). Perhaps stricter terms must be taken into account.
Note: Check before using the OSPREY G3 series whether damages in transit have been
happened and arrange a repair of these damages if necessary.
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 13 -
Conformity Declaration OSPREY G3 Series
Conformity Declaration
to EMV/EMC guideline (89/336/EC)
to low-voltage guideline (73/23/EC chapter 10)
The manufacturer:
TAMUZ Broadcast
Kirchweg 62B
D-24558 Henstedt-Ulzburg
declares hereby, that the product:
Product name: Monitor
Model number: OSPREY G3 series
Year of construction: 2012
corresponds to the regulations of the guidelines described above:
The following harmonized norms were used:
EN 55011 ISM Equipment, Group 1, Class A
EN 55022 Conducted Emissions, Class B
EN 50081-2 Generic standard interference transmission, industry area
EN 50082-2 Generic standard interference immunity, industry area
prEN55103-1 EMV product family norm for Audio-, Video and audio-visual facilities
as well as for studio light control facilities for the professional usage,
-Part 1: Limiting values and measurement procedure for disturbing
emissions
prEN55103-2 EMV product family norm for Audio-, Video and audio-visual facilities
as well as for studio light control facilities for the professional usage,
-Part 2: Requirements on the interference immunity
EN 61000-3-2 Power Factor Harmonic Correction
EN 61000-3-3 Flicker & Voltage Fluctuation Limits
EN 61000-4-2 Electrostatic Discharge Immunity
EN 61000-4-3 Radiated Electromagnetic Fields
EN 61000-4-4 Fast Transients-Burst Immunity
EN 61000-4-5 Input Surge Immunity
EM 61000-4-6 Conducted RFI
EN 61000-4-11 Voltage Dips
The following national or international norms (or parts/clauses from this) and specifications were used:
DIN EN 6099 Verbindungsmaterial für Niederspannungsstromkreise für Haushalt und
ähnliche Zwecke; Teil 1: Allgemeine Anforderungen
IEC 127-6 Geräteschutzsicherungen
Henstedt-Ulzburg, 08.10.2012
Erwin W. Lissy
CEO / President
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 14 -
Technical Data OSPREY G3 Series
Technical Data
System Hardware
The hardware of the Video Monitor consists of the following components which are installed in an elegant and emission shielded full metal system-unit cover of high quality:
Item KVM 1750W KVM 1751 W KVM 2250W KVM 2350W KVM 2450W
System Frame KVM 1750 KVM 1750 KVM 2250 KVM 2350 KVM 2450
Dimensions 430 x 290 x 80 430 x 290 x80 530 x 350 x 85 560 x 410 x 85 575 x 420 x 85
Weight 5,8 kg 5,8 kg 6,7 kg 0 kg 9,3 kg
Mounting VESA 100 VESA 100 VESA 100 VESA 100 VESA 100
Display Size 17.1“ 17“ 215“W 23.5“W 24“
Display Type *
1
*
1
*
1
*
1
*
1
Display Technology amorph silicon amorph silicon amorph silicon amorph silicon amorph silicon
Resolution 1920 x 1080 1366 x 768 1920 x 1080 1920 x 1080 1920 x 1200
Dot Format RGB, square RGB, square RGB, square RGB, square RGB, square
Display Aspect Ratio 16 : 9 16 : 9 16 : 9 16 : 9 16 : 10
Color Format 30 bit full color 24 bit full color 24 bit full color 24 bit full color 30 bit full color
Luminance max. 300 cd/m2max. 400 cd/m2max. 400 cd/m2max. 450 cd/m2max. 400 cd/m
2
Contrast >1.000 : 1 >900 : 1 >1.000 : 1 >1.000 : 1 >1.000 : 1
Viewing Angle ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V
Viewing Direction 06:00 h 06:00 h 06:00 h 06:00 h 06:00 h
Display Class ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2
Pixel Error Class class 2 class 2 class 2 class 2 class 2
*1 = or similar alternative, *2 = optional feature
© 03.14 TAMUZ Broadcast Digital Broadcast Monitor Page - 15 -
Loading...