n
S88-3
n
n
s88-Rückmelder
s88-Feedback Module
Décodeur s88
s88-Terugmelder
Art.-Nr. 44-01305 / 44-01306 / 44-01307
n
n
n
n
n
Anleitung
n
n
Manual
n
Mode d´emploi
n
Handleiding
n
n
n
© 06/2008 Tams Elektronik GmbH
Alle Rechte, insbesondere das Recht
der Vervielfältigung und Verbreitung
sowie der Übersetzung vorbehalten.
in jeglicher Form bedürfen der
schriftlichen Genehmigung durch die
All rights reserved. No part of this
publication may be reproduced or
transmitted in any form or by any
means, electronic or mechanical,
permission in writing from Tams
ainsi que le traduction. Toute
duplication ou reproduction sous
quelque forme que ce soit nécessite
l´accord écrit de la societé Tams
Sous réserve de modifications
Alle rechten voorbehouden. Niets uit
deze publicatie mag worden
vermenigvuldigd opgeslagen of
openbaar gemaakt, zonder
Technische wijzigingen voorbehouden.
Vervielfältigungen und Reproduktionen
Tams Elektronik GmbH.
Technische Änderungen vorbehalten.
n
n
n
n Deutsch 3
© 06/2008 Tams Elektronik GmbH
including photocopying, without prior
Elektronik GmbH.
Subject to technical modification.
© 06/2008 Tams Elektronik GmbH
Tout droits réservés, en particulier les
droits de reproduction et de diffusion
Elektronik GmbH.
techniques.
© 06/2008 Tams Elektronik GmbH
voorafgaande schriftelijke toestemming
van Tams Elektronik GmbH.
n English 18
n Français 33
n Nederlands 48
n
n
n
n
n
n
n
n
n
English S88-3
Table of contents
1. Getting started 19
2. Safety instructions 20
3. Safe and correct soldering 23
4. Operation overview 24
5. Technical specifications 25
6. Assembling the S88-3 25
7. Connecting the S88-3 29
8. Check list for troubleshooting 30
9. Manufacturer's note, CE and Warranty 30
Parts list I.1
Printed Circuit Board (PCB) layout (Fig. 1) I.2
Circuit Diagram (Fig. 2) II
Connections diagram (Fig. 3) III
(Pages I to III in the centre of this handbook are removable.)
Page 18
S88-3 English
!
1. Getting started
How to use this manual
This manual gives step-by-step instructions for safe and correct
assembly of the kit and fitting of the ready-built module, and operation.
Before you start, we advise you to read the whole manual, particularly
the chapter on safety instructions and the FAQ chapter. You will then
know where to take care and how to prevent mistakes which take a lot
of effort to correct.
Keep this manual safely so that you can solve problems in the future. If
you pass the kit or the ready-built module on to another person, please
pass on the manual with it.
Intended use
The kit or the ready-built module can be assembled and operated with
a digital model railway to feedback data via the s88 bus using this
manual.
Any other use is inappropriate and invalidates any guarantees.
The kit and the ready-built module should not be assembled or fitted by
children under the age of 14.
Reading, understanding and following the instructions in this manual
are mandatory for the user.
Caution:
The circuit contains integrated circuits. These are very sensitive to static
electricity. Do not touch components without first discharging yourself.
Touching a radiator or other grounded metal part will discharge you.
Page 19
English S88-3
Checking the package contents
Please make sure that your package contains:
§ one kit, containing the components listed in the parts and one PCB
or one ready-built module,
§ an Ethernet patch cable (length: 0,5 m),
§ one manual.
Required materials
For assembling the kit you need:
§ an electronic soldering iron (max. 30 Watt) with a fine tip,
§ a soldering iron stand,
§ a tip-cleaning sponge,
§ a heat-resistant mat,
§ a small side cutter and wire stripper,
§ a pair of tweezers and long nose pliers,
§ tin solder (0,5 mm. diameter),
In order to connect the module you need wire. Recommended
diameters: > 0,25 mm² for the connections to the rails.
2. Safety instructions
Mechanical hazards
Cut wires can have sharp ends and can cause serious injuries. Watch
out for sharp edges when you pick up the PCB.
Visibly damaged parts can cause unpredictable danger. Do not use
damaged parts: recycle and replace them with new ones.
Electrical hazards
§ Touching powered, live components,
§ touching conducting components which are live due to malfunction,
§ short circuits,
§ connecting the circuit to another voltage than specified,
Page 20
S88-3 English
§ impermissibly high humidity,
§ condensation build up
can cause serious injury due to electrical shock. Take the following
precautions to prevent this danger:
§ Never perform wiring on a powered module.
§ Assembling and mounting the kit should only be done in closed,
clean, dry rooms. Beware of humidity.
§ Only use low power for this module as described in this manual and
only use certified transformers.
§ Connect transformers and soldering irons only in approved mains
sockets installed by an authorised electrician.
§ Observe cable diameter requirements.
§ After condensation build up, allow a minimum of 2 hours for dispersion.
§ Use only original spare parts if you have to repair the kit or the
ready-built module.
Fire risk
Touching flammable material with a hot soldering iron can cause fire,
which can result in injury or death through burns or suffocation.
Connect your soldering iron or soldering station only when actually
needed. Always keep the soldering iron away from inflammable
materials. Use a suitable soldering iron stand. Never leave a hot
soldering iron or station unattended.
Thermal danger
A hot soldering iron or liquid solder accidentally touching your skin can
cause skin burns. As a precaution:
§ use a heat-resistant mat during soldering,
§ always put the hot soldering iron in the soldering iron stand,
§ point the soldering iron tip carefully when soldering, and
§ remove liquid solder with a thick wet rag or wet sponge from the
soldering tip.
Page 21
English S88-3
Dangerous environments
A working area that is too small or cramped is unsuitable and can cause
accidents, fires and injury. Prevent this by working in a clean, dry room
with enough freedom of movement.
Other dangers
Children can cause any of the accidents mentioned above because they
are inattentive and not responsible enough. Children under the age of 14
should not be allowed to work with this kit or the ready-built module.
Little children can swallow small components with sharp edges, with
fatal results! Do not allow components to reach small children.
In schools, training centres, clubs and workshops, assembly must be
supervised by qualified personnel.
In industrial institutions, health and safety regulations applying to
electronic work must be adhered to.
Page 22
Loading...