TC1000
T
CPG.3
All Weather
VENTILATOR
PRODUCT MANUAL & INSTALLATION GUIDE
Serial Number
Date of Purchase
Point of Purchase
The serial number is located on the shipping carton
and on a label affixed to the upper housing.
Unpacking your TC:
TC1000-T
One (1) TC1000-T
One (1) Line Voltage Thermostat
The TC 1000 can be installed in one of three ways:
• In a glazing system -
system, an internal spacer to match the thickness of the glazing must be factory installed, or one fabricated on the site.
If a spacer is site fabricated, please note that it must be installed UNDER the fan.
• On a conventional or stress skin panel roof -
After a 12 1/2" x 27" rough opening is cut through the roof, a sheet metal "thimble" should be installed to line the opening
The fan should be installed using standard skylight flashing techniques and an optional grille is recommended to
cover the opening in the ceiling.
• On a vertical wall -
it hits the edge of the fan.
The TC 1000 must be installed by a qualified installer. If it is to be installed in a double glazing
We strongly suggest installing a piece of flashing above the TC 1000 to sweep the rain away before
When you have unpacked your TC carefully you will find the following:
TC1000-H
All Weather
Ventilator
The TC 1000 will have no internal spacer - its flanges will be 1/4" thick.
One (1) TC1000-H All Weather Ventilator
CA
W
UT
WARNI
READ AND SAVE THESE INSTRUCTIONS
NG
:
TO
R
ED
U
C
E TH
E R
ISK O
F FIR
E, ELEC
Use
th
i
s u
n
i
t i
n
th
e
ma
n
n
e
r
i
n
te
n
d
e
d
b
y th
Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being
switched on accidentally
device, such as a tag, to the service panel.
When cutting or drilling into wall or ceiling, do not damage electrical wiring or other hidden utilities.
Never place a switch where it can be reached from a tub or shower.
Do not use this fan over a tub or shower.
Do not use this fan over cooking appliances.
ARNING:
ION: F
To Red
or General
u
c
Venti
. When the service disconnect cannot be locked, securely fasten a prominent warning
e The Risk of Fir
l
ation Us
e or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.
e Onl
y. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors
e
ma
TR
IC
SH
O
C
K, O
R
IN
JU
R
Y TO
PER
SO
N
S, O
BSER
VE TH
E FO
LLO
WIN
n
u
fa
ctu
r
e
r. If yo
u
h
a
ve
a
n
y q
u
e
sti
o
n
s, co
n
ta
ct th
e
ma
n
u
fa
ctu
r
e
r.
320 Main Street • Buzzards Bay, Ma 02532
508-759-4660 / 800-222-5932 / Fax 508-759-6001
G
:
Installation
Installing the TC1000 in a Wall
You will need the following items:
• Two pieces of 2x stock to match your existing framing
• Saw to cut the hole in the wall
• Hammer or Screw Gun to attach the blocking to the existing frame
• Phillips head Screwdriver to attach the grille
• Weather strip material
• Low expansion Spray Foam sealant
Add framing as
shown to create
a box of 12 1/2”
x 27 3/4”. This
box will act to
hold the unit as
well as creating
a plenum for air
movement.
(Figure 1)
16” OC
1. Create a box to hold the unit (Fig. 1).
2. Remove the sheathing that covers the box.
3. Attach TC1000, screwing through the mounting flange.
4. Install exterior finish materials over the mounting flange.
Note: additional flashing may be required above the unit to divert rain.
5. Remove any interior materials covering the box.
6. Install interior finish materials to trim the frame.
7. Attach optional grille to finish installation.
Loading...