Tamarack Technologies Infinity 1100 Product Manual & Installation Manual
All Weather
VENTILATOR
PRODUCT MANUAL & INSTALLATION GUIDE
TC1000-H
One (1) TC1000-H All Weather Ventilator
TC1000-T
One (1) TC1000-T
All Weather
Ventilator
One (1) Line Voltage Thermostat
The serial number is located on the shipping carton
and on a label affixed to the upper housing.
TC1000
READ AND SAVE THESE INSTRUCTIONS
T
CPG.3
Serial Number
Date of Purchase
Point of Purchase
The TC 1000 can be installed in one of three ways:
• In a glazing system -
The TC 1000 must be installed by a qualified installer. If it is to be installed in a double glazing
system, an internal spacer to match the thickness of the glazing must be factory installed, or one fabricated on the site.
If a spacer is site fabricated, please note that it must be installed UNDER the fan.
• On a conventional or stress skin panel roof -
The TC 1000 will have no internal spacer - its flanges will be 1/4" thick.
After a 12 1/2" x 27" rough opening is cut through the roof, a sheet metal "thimble" should be installed to line the opening
The fan should be installed using standard skylight flashing techniques and an optional grille is recommended to
cover the opening in the ceiling.
• On a vertical wall -
We strongly suggest installing a piece of flashing above the TC 1000 to sweep the rain away before
it hits the edge of the fan.
WARNI
NG
:
TO
R
ED
U
C
E TH
E R
ISK O
F FIR
E, ELEC
TR
IC
SH
O
C
K, O
R
IN
JU
R
Y
TO
PER
SO
N
S, O
BSER
VE TH
E FO
LLO
WIN
G
:
Use
th
i
s u
n
i
t i
n
th
e
ma
n
n
e
r
i
n
te
n
d
e
d
b
y th
e
ma
n
u
fa
ctu
r
e
r. If yo
u
h
a
ve
a
n
y q
u
e
sti
o
n
s, co
n
ta
ct th
e
ma
n
u
fa
ctu
r
e
r.
Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being
switched on accidentally. When the service disconnect cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
When cutting or drilling into wall or ceiling, do not damage electrical wiring or other hidden utilities.
Never place a switch where it can be reached from a tub or shower.
Do not use this fan over a tub or shower.
Do not use this fan over cooking appliances.
WAR
NING:
T
o
Re
du
ce
Th
e Risk o
f Fir
e
o
r Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.
CAUT
ION: F
or General
Venti
l
ati
on Us
e Onl
y
. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors
320 Main Street • Buzzards Bay, Ma 02532
508-759-4660 / 800-222-5932 / Fax 508-759-6001
When you have unpacked your TC carefully you will find the following:
Unpacking your TC:
Installation
Installing the TC1000 in a Wall
You will need the following items:
• Two pieces of 2x stock to match your existing framing
• Saw to cut the hole in the wall
• Hammer or Screw Gun to attach the blocking to the existing frame
• Phillips head Screwdriver to attach the grille
• Weather strip material
• Low expansion Spray Foam sealant
1. Create a box to hold the unit (Fig. 1).
2. Remove the sheathing that covers the box.
3. Attach TC1000, screwing through the mounting flange.
4. Install exterior finish materials over the mounting flange.
Note: additional flashing may be required above the unit to divert rain.
5. Remove any interior materials covering the box.
6. Install interior finish materials to trim the frame.
7. Attach optional grille to finish installation.
16” OC
Add framing as
shown to create
a box of 12 1/2”
x 27 3/4”. This
box will act to
hold the unit as
well as creating
a plenum for air
movement.
(Figure 1)
Loading...