VD960AW
AHD/960H Fixed 3.6mm Vandal IR Dome Camera
Overview
- 1/4" 1MP CMOS Sensor
- AHD 720P and 960H Resolution
- 3.6mm Fixed Lens
Note: Before providing power to the camara, please read this user guide in detail.
Do not attempt to disassemble the camera. If problems persist, please contact your local dealer or Talos Security.
Introduction
Thank you for your purchase of Talos product VD960AW.
Please read this instruction manual carefully to ensure proper use of
this equipment.
To prevent fire or shock hazard, do not expose the
unit to excessive rain or moisture.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
DIGITAL
WDR
0
52dB
DC 12V
Specifications
Model:
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Image Pick-up Device
Scanning System
Synchronization
Horizontal Resolution
Min. Illumination
S / N Ratio
Video Output
LENS
Auto Electronic Shutter
Focal Length
Angle Field of View
OPERATIONAL
Gama Characteristics
Auto Gain Control
IR Distance
3-DNR & AGC
ENVIRONMENTAL
Operating Temp/Humidity
Storage Temp/Humidity
MECHANICAL
Dimensions
Weight
(Y signal)
12V DC (±10%) , 500mA – 650mA
8 Watt
1/4" 1.0 Megapixel CMOS Sensor
Progressive
Internal, Negative sync
720p
0.01 Lux/F1.2, 0 Lux (with IR LED ON )
Less than 50dB
1.0Vp-p, 75
NTSC: 1/60s~1/100,000s, PAL: 1/50s~1/100,000s
3.6mm Fixed Lens
70°
0.45
Auto
20 meters
On / Off (Low / Middle / High) Selectable
-10~50°C RH95% Max
-30~+60°C RH95% Max
260 (W) x 98 (H) x 95 (D)
450 g (1 lbs)
VD960AW
Features
● 1/4" 1MP CMOS Sensor
● Built-in auto gain
● 130° ~ 28° angle field of view
● D-WDR (Digital Wide Dynamic Range)
● IR illuminators for seeing in the dark!
● Water resistance: IP66
Packing List
No Name Model Number
1
2
Vandalproof Dome Camera VD960AW 1
User Guide VD960AW 1
Dimensions
94
69
Unit : mm
VD960AW
EXPOSURE
BACK LIGHT
AHD/960H Fixed 3.6mm Vandal IR Dome Camera
OSD Menu Settings
960H MODE: Hold “left” key 5 sec. AHD MODE: Hold “right” key 5 sec.
System Menu: Push “depress” joystick 5 sec.
MANUAL/DC
AUTO, 1/30, 1/60, FLK, 1/240, 1/480, 1/1000
1/2000, 1/5000, 1/10000, 1/50000, X2, X4,
X6, X8, X10, X15, X20, X25, X30
0 – 15
AUTO (X2 - X30)/OFF
0 – 100
OFF/ON
OFF/AUTO
OFF
BLC:LEVEL/AREA/DEFAULT
HSBLC:SELECT AREA/DISPLAY/BLACK MASK/
LEVEL/MODE/DEFAULT
D→N(DELAY)/N→D(DELAY)
D→N(AGC)/D→N(DELAY)/
N→D(AGC)/N→D(DELAY)
BURST/IR SMART/IR PWM
OFF/LOW/MIDDLE/HIGH
OFF/LOW/MIDDLE/HIGH
FREEZE/MIRROR/NEG.IMAGE
SELECT AREA1-4/DISPLAY/SENSITIVITY/
COLOR/TRANS/ALARM/DEFAULT
ENG/CHN1/CHN2/GER/FRA/ITA/
BAUDRATE:2400/4800/9600/19200/38400
OFF/ON
OFF/ON
SPA/POL/RUS/POR/NED/TUR
LIVE DPC
WHITE DPC
BLACK DPC
CAM ID:0-255
ID DISPLAY
AUTO/OFF
LCD/CRT
OFF/ON
PAL/NTSC
MAIN
MENU
LENS
WHITE BAL
DAY &
NIGHT
NR
SPECIAL
ADJUST
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
ATW/ATC→SET/INDOOR/OUTDOOR/MANUAL/AWB
EXT
AUTO
COLOR
B/W
2DNR
3DNR
CAM TITLE
D-EFFECT
MOTION
PRIVACY
LANGUAGE
DEFECT
RS485
SHARPNESS
MONITOR
LSC
VIDEO.OUT
Connecting
Monitor/DVR
VD960AW
Connection Polarity:
VIDEO
POWER
Troubleshooting
1. No Picture after providing power
GND VIDEO
LEFT
ENTER - PUSH DOWN
~ Check that the power supply is the proper voltage and polarity.
~ Check all connections to DVR.
~ Check the video signal type.
2. The picture has rolling lines or ripples
~ Check for AC power lines running in close proximity to the camera
or its cabling.
~ Check that all connections are securely connected to the DVR.
3. Innaccurate/changing color balance
~ External lighting sources such as fluorescent lamps can confuse
the image sensor. Move the camera or change the light source
in the monitored area.
4. Blurred or hazy image
~ Check that the camera lens is clean and free of any dirt,
fingerprints, moisture.
~ Check that camera lens has not been adjusted out of its focus range.
~ Check that camera has not been disassembled or missi
any moisture seals.
OSD CONTROL
UP
DOWN
RIGHT
ng
DC12V
Power Supply
VIDEO
DC12V
Notes:
● The power supply must be installed in a dry location. Only use a
power supply with the proper voltage, current and polarity as
required by this camera.
● During severe weather, it is recommended that the product be
disconnected from the power source to prevent damage from
voltage spikes.
● For proper operation, avoid excessive cable lengths.
● Only use the camera in the proper operating temperature range
of -10º to 115ºF.
● Avoid installing in direct sunlight as this can damage the image sensor.
● Do not mount the camera near any heat source.
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER OR BACK.
NO USER SERVICABLE PARTS INSIDE.
TO PREVENT ELECTRIC SHOCK AND RISK OF FIRE HAZARDS,
DO NOT USE OTHER THAN SPECIFIED POWER SOURCE.
Loading...