DC700WICR
User Manual
talossecurity.com
TOP
FRONT
104
130
VIDEO NTSC PAL
Image Pick-up Device
Total Pi xels 1020(H) x 508(V) 1020(H) x 596(V)
Effective Pixe ls 976(H) x 494(V) 976(H) x 582(V)
Inter. H/V
15,734/59.94Hz 15,625/50Hz
LL H/V 15,750/60Hz 15,625/50Hz
Horizontal Resolution
S / N Ra tio (Y signal)
OSD
Day & Night
ATW
High Spee d Shutter
Flickerle ss
WDR
AGC
Iris
Intelli gent DNR
Sens Up
Smart I R
White Bala nce
Line Lock
Camera ID
Motion Detection
Privacy Ma sking
Etc. Function
External Control
Alam Output
Video Output
Powe r Input
Powe r Consumption
Operating Temperature
Operating Humidity
Dimensions
Wei ght
104(H) x 130(D)
460g
700TV line
On/Off (Level Setting)
Level Setting
DC Auto Iris / Manual Iris
X 512
On/Off
Absolute :-10°C ~ +50°C
Less than 90%
4 Area
15 Area (W/Mosaic etc.)
BLC, Intelligent HLC, DIS, D-Zoom, Sharpness, M irror
On/Off (Phase Control)
ATW/Push/User1/User2/Anti CR/Manual/Push Lock
RS-485 (PELCO D)
Sony 1/3" Dual Sc an 520K-Effective Pixel Super HAD CCD II
2D + 3D
Less than 400mA
Min. Il lumination(F1.2)
Color : 0.1 Lux(50IRE) / 0.0002 Lux(Sens up X512)
B/W : 0.08 Lux(50IRE) / 0.00015 Lux(Sens up X512)
More than 52dB
1ea (Open Collector)
VBS 1.0Vp-p (75Ω Terminated)
DC12V
Multi-language support
Software / Lens Color or BW(with Motor Drive)
1800 ~ 10,500K
1/60(1/50) ~ 1/10Ksec
On/Off
On/Off (Letter A to Z, Numerals 0 to 9, Sy mbols)
Video Jack
(BNC/RCA)
Video Signal
Video GND
Cable Connection
12V DC & 24V AC Automatic Power
conversion System Built-in
Video Jack
DC/AC Switched
Without
Nega(-)/Posi(+)
Camera Adjustment
1. Please stick the surface mounting base on the wall or ceiling after placing water-resistance gasket on the bottom of base.
(As occasion demands, please use Anchor & Ceiling screw at the same time)
(In case of Flush Mounting base, make sure the insert hole & Video/Power connection in advance )
2. Connect Video (BNC-Fe or RCA-Ma) & Power (12VDC ro 24VAC Power Input)
- Warning!!!
The use of a CSA Certified/UL Listed Class2 Power supply is required to ensure compliance with electronical safety standard.
Camera automatically converts its proper power input whether it is 12VDC or 24VAC.
3. Please slowly insert Flush mounting base in the sticking surface mounting base and tighten base fixing screw.
4. Tighten body cover locking screw(Hexa Screw) using 'L'wrench after setting the camera view position & focus.
Termial
Block
UP
RIGHT
LEFT
DOWN
PUSH
MENU SETUP/ENTER
Extra Service Preview
Video output
Ceiling Screw hole
INSTALLATION
Gimbal Cap
Ceiling Screw
Camera Mounting
Base
Body Cover
2
/ AC24V ±10%
DIMENSIONS
SPECIFICATIONS
Loading...