Page 1
Operator’s manual Matrix printer
T2280
SprintPro
T2265
SprintPro
®
Page 2
Important Information
This equipment generates and uses radio frequency energy and
if not installed and used properly, that is, in accordance with the
manufacturer’s instructions, may cause interference in radio and
television reception. It has been type tested and found to comply
with the limits for class B computing devices in accordance with
the specification in subpart J of part 15 of FCC rules, which are
designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a partial installation. If
this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna,
Relocate the peripheral away from the receiver,
Move the peripheral away from the receiver
Plug the peripheral into a different outlet, so that the
peripheral and receiver are on different branch circuits
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The
user may find the following booklet, prepared by the Federal
Communications Commission, helpful: “How to Identify and
Resolve Radio-TV Interference Problems”.
This booklet is available from the U.S. Government Printing
Office, Washington DC 20402 Stock No. 004.000.00345.4.
WARNING:
To comply with FCC regulations on electromagnetic
interference for a class B computing device, the printer cable
must be shielded. To assure compliance with FCC regulations
for a computing device, use a shielded interface cable with a
metal shell connector. The use of cables not properly shielded
may result in violating FCC regulations.
This digital apparatus does not exceed the class B limits for radio
noise emissions from digital apparatus as set out in the radio
interference regulations of the Canadian department of communications.
This unit complies with DOC standard C108.8-M 1983
ATTENTION: Le présent appareil numérique n’ement pas de
bruits radioélectriques déspassant les limites applicables aux
appareils numériques de la classe B prescrites dans le règlement
sur le brouillage radio- électrique édicté par le minstère des
communications du Canada.
The paper used is made of raw materials treated with a
chlorine-free bleaching process.
WARNING For continued protection against risk of fire, replace only with same type and rating of fuse.
Only trained and qualified personnel may open covers or remove parts that are not explicitly shown and described in the User
Guide as being accessible to the operator.
ATTENTION Pour ne pas compromettre la protection contre les risques d’incendie, remplacer par un fusible de même type et de mêmes
caractèristiques nominales.
Seul un personnel qualifié et formé est habilité à démonter les sous-ensembles de la machine qui ne sont pas formellement
indiqués dans le Manuel d’utilisation meme s’ils sont accessibles par l’opérateur.
This device fulfils the European standards requirements by complying with the
Directive of the Commission dated May 3, 1989 (89/336/EEC) relating to
electromagnetic compatibility and the Directive dated February 19, 1973
(73/23/EEC) relating to low-voltage electrical equipment. Conformity with the above mentioned Directives is indicated by the CE symbol attached to the device.
Note: Conformity may be affected by:
using interface cables not complying with the specifications
non-observance of important instructions in the operator’s manual
installing components not approved for this device by the manufacturer
unauthorized manipulation
Page 3
Operator’s Manual
QUICK START-UP
T able of contents
Table of contents
Introduction 2
Symbols used 2
Important safety instructions 2
Using the Online-CD-ROM 3
Contents of the Online CD-ROM 3
Hardware requirements 3
Troubleshooting 3
Printer at a glance 4
Installation 5
Unpacking the printer 5
Placing your printer 6
Connecting the printer 7
Switching on the printer 7
Control panel 8
Online mode 8
Offline mode 8
Setup mode 8
Changing the ribbon cassette 9
Paper handling 14
Changing the paper type 14
Loading paper 15
Fanfold paper 15
Single sheets 17
Paper transport 18
Moving the paper to the tear position 19
Settings 20
Setting the tear position 20
Setting the first printing line (TOF) 21
Setting the print head gap 22
Selecting character density and font 23
Technical data 24
Printer specifications 24
Paper specifications 25
Accessories 26
ENGLISH
Quick start-up Table of contents
1
Page 4
Introduction This Operator’s Manual is intended as a quick introduction into working with the printer and
also to enable inexperienced users to operate the device properly. It describes the most important functions of the printer and contains the essential information for your everyday work
with the printer. A more detailed description of the printer, its characteristic features, and further information is contained in the Reference Manual on the Online CD-ROM, which is inserted at the back of this manual.
➤ Symbols used Important information is highlighted in this manual by two symbols.
CAUTION highlights information which must be observed in order to prevent injuries to the
user and damage to the printer.
NOTE highlights general or additional information about a specific topic.
➤ Important safety
instructions
Read the following instructions thoroughly before starting up your printer in order to prevent
injuries and avoid damage to the device.
Keep this Operator’s Manual in a place which is easily accessible at all times.
Place the printer on a solid base so that it cannot fall down to the ground.
Do not expose the printer to high temperatures or direct sunlight.
Keep all liquids away from the printer.
Protect the printer from shock, impact and vibration.
Be sure to connect the printer to a socket with the correct mains voltage.
The power supply cable may be damaged if the paper edges constantly chafe the insulating
sheath. The user must always ensure that there is sufficient distance between the power supply cable and the paper.
Never carry out maintenance or repair work yourself. Always contact a qualified service
technician.
Whenever you want to disconnect the printer from the power supply, pull the plug out from
the mains socket.
Additional safety instructions are provided at the relevant places in the text.
STOP
STOP
STOP
Ah ha!
!
Introduction Quick start-up
2
Page 5
➤ Using the
Online-CD-ROM
First install the Adobe Acrobat Reader on your hard disk, unless the program has already
been installed. To install it, follow the steps described in the README file in the READER
directory.
To start the online documentation, call the File Manager (Windows 3.1) or Explorer
(Windows 95/98, Windows ME, Windows 2000, Windows NT4) and double click on the
ST ART.PDF file. Then follow the instructions and menus on the screen.
➤ Contents of the
Online CD-ROM
The Online CD-ROM contains
– the Reference Manual: A detailed description of the printer and its impressive features
– Drivers: For Windows 3.1, Windows 95/98, Windows ME, Windows 2000, Windows NT4
– Additional documentation: Programming instructions and descriptions of the available
options
If your CD-ROM is be defective or missing, please consult your dealer. The Online Documentation is also available as a hardcopy (at a cost) or can be downloaded via the Internet.
➤ Hardware
requirements
Minimum hardware requirements: PC 486 MHS, quad-speed CD-ROM, 15" display screen,
mouse.
➤ Troubleshooting The online documentation supplied on the CD-ROM contains detailed information on trouble-
shooting.
ENGLISH
Quick start-up Introduction
3
Page 6
Printer at a glance
Top cover
Soundproofing cover
Control panel
Power switch
Front cover
Bottom cover
Printer in tractor mode View from the front
Tractors
Printer in single-sheet mode View from the rear
Power cord connector
Interface
connectors
Paper support
Single sheet feeder Paper guide
Rear cover
Printer at a glance Quick start-up
4
Page 7
Installation
➤ Unpacking the printer
Place your printer on a solid base.
Make sure that the “Up” symbols point in the correct direction.
Open the packaging, take out the accessory cassette and unpack it. Pull the printer out of the cardboard box towards you
and remove the remaining packaging material.
Check the printer for any visible transport damage and missing items. In addition to this Operator’s Manual (➀) the CDROM (➁, at the back of this manual), the power cable (➂)
and the ribbon (➃) must be included.
If you find any transport damage or if any accessories are
missing, please contact your dealer.
➀
➁
➂
➃
ENGLISH
Quick start-up Installation
5
Page 8
➤ Placing your printer Place the printer on a solid, flat, surface, ensuring that the printer is positioned in such a way
that it can not topple, and that there is easy access to the control panel and paper input
devices. Also ensure that there is sufficient space for the printed output.
If you expect that frequent forward and reverse feeds will
occur, you should place the printer as shown in the figure, if
possible.
When selecting the printer location, observe the following additional instructions:
Never place the printer in the vicinity of inflammable gas or explosive substances.
Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain.
When connecting a computer to the printer, make sure not to exceed the maximum cable
length (see Reference Manual on the Online CD-ROM, Technical Specifications).
Ensure sufficient distance between the printer and any heating devices/radiators.
Avoid exposing the printer to extreme temperature or air humidity fluctuations. Protect the
printer from dust.
It is recommended to install the printer in a place which is acoustically isolated from the
workplace because of the noise it may produce.
STOP
Installation Quick start-up
6
Page 9
➤ Connecting the printer
Make sure that the printer is set to the correct voltage (e.g.
230 V in Europe, 120 V in the U.S.A.). To do this, check the
plate above the power inlet at the rear of the printer.
If the setting is incorrect, set the coloured switch at the rear
of the printer to the correct position, using a pointed object
(e.g. screwdriver, ball pen or tweezers).
Make sure that the printer and the computer are switched off,
and connect the printer to the computer with the data cable
(interface cable).
Connect the power cable to the power inlet of the printer.
Connect the power cable plug to a mains socket.
➤ Switching on the printer
The power switch for switching on the printer is located at
the bottom left at the front of the printer when viewed from
the front.
120V
Make sure that the printer is switched off before setting the correct voltage; otherwise severe damage
may be caused.
Never switch on the printer if the voltage setting is
incorrect, since this may cause severe damage to
the printer.
STOP
ENGLISH
Quick start-up Installation
7
Page 10
Control panel The control panel and the keys are used for controlling the printer operation.
The upper line of the display shows whether the printer is in Online or Offline mode and the
paper path selected (Tractor1 or Single).
➤ Online mode After switching on, the printer is automatically set to online mode. Only in this mode can it
receive data from the computer.
Tear key (4): Activates the tear function when fanfold paper is loaded (see
page 19, Moving the paper to the tear position). If Load is displayed above
this key, no paper is loaded in the printer; press the key to feed paper to the
printing position.
Setup key: Sets the printer to setup mode.
Online key: Sets the printer to offline mode.
➤ Offline mode Only in this mode is it possible to perform step, line, or form feeds from the control panel (see
page 18, Paper transport); however, data cannot be received.
Park key (1): Clears the paper path with paper loaded and activates paper
path quick selection (see page 14, Changing the paper type).
Key (2): Short keypress: Microstep forward.
Long keypress: Continuous paper feed.
Key (3): Short keypress: Microstep reverse.
Long keypress: Continuous paper reverse feed back to the park position.
Load key (4): If no paper is loaded, see above.
If paper is loaded: Short keypress: Line Feed (LF);
long keypress: Form Feed (FF).
Setup key: Sets the printer to setup mode.
Online key: Sets the printer to online mode.
➤ Setup mode In this mode, the following settings are available:
Setup key: Sets the printer to setup mode, in which the following
settings can be selected:
Menu key (1): Other menu settings.
Adjust key (2): Tear position, first printing line and print head gap.
Paperway key (3): Paper path.
Char key (4): Font and number of characters per inch.
Access to the other menu settings (Menu) may be disabled by the manufacturer. For information on how to enable access and about the available settings, refer to the Reference Manual
on the Online CD-ROM (chapter The Menu, section Enabling the menu).
Online Tractor1
Tear
Online
Setup
21
3
4
Offline Tractor1
Load
Online
Setup
Park Load
21
3
4
Adjust Paperway
Menu Char
Online
Setup
21
3
4
Control panel Quick start-up
8
Page 11
Changing the
ribbon cassette
Before opening the cover, make sure that the printer is switched on so that it can execute automatic preparations for ribbon changing (widening the print head gap).
Move the paper to the park position.
Open the printer top cover.
Carefully slide the print head carriage to the left stop (viewed
from the printer front).
The print head becomes hot during printing. For
this reason, let it cool down before touching it.
STOP
ENGLISH
Quick start-up Changing the ribbon cassette
9
Page 12
Move the coloured friction tab to the left (direction of the
arrow) as shown in the figure and raise the friction mechanism.
Remove the used cassette.
We recommend use of genuine ribbon cassettes only.
Changing the ribbon cassette Quick start-up
10
Page 13
Raise the coloured insertion tongue A.
Insert the coloured ribbon tension knob into the right-hand
front location of the new ribbon cassette. Turn the knob in the
direction of the arrow in order to take up the slack of the ribbon.
Tilt the ribbon cassette slightly forward, and thread in the ribbon between the coloured insertion tongue and the ribbon
support (transparent plastic plate).
Align the cassette and insert it, then press down until it clicks
into place.
A
ENGLISH
Quick start-up Changing the ribbon cassette
11
Page 14
Insert the coloured tension knob into one of the two locations.
Turn the tension knob to take up slack in the ribbon until it is
seated correctly at the bottom in the ribbon support.
Press down the coloured insertion tongue A.
A
Changing the ribbon cassette Quick start-up
12
Page 15
Move the print head carriage backwards and forwards several
times. If the ribbon is correctly seated, there must be no perceptible resistance.
Press the friction mechanism down until it clicks into place.
Close the front section of the top cover.
The ribbon should be transported during the travel
from left to right. If this is not the case, you should
check that the ribbon cassette is correctly inserted
on the right.
ENGLISH
Quick start-up Changing the ribbon cassette
13
Page 16
Paper handling This section describes how to set the paper type, load fanfold paper and single sheets, trans-
port paper and move the paper to the tear position.
➤ Changing the
paper type
You can change the paper type either from an application program, by means of the paper
path quick selection feature or in the Setup menu. In this section, the quick selection feature
is described; for detailed information on how to make this setting via the Setup menu, refer
to the Reference Manual on the Online CD-ROM.
On some printer models, the single sheet paper source cannot be selected since these models
are not designed for manual single sheet feeding.
Make sure that the printer is in offline mode; press the Online key, if necessary.
Press the Park (1) key. If fanfold paper is loaded in the printer, it is fed to the
tear position. The text tear paper off appears in the display. Then press any
key. If a single sheet is loaded in the printer, it is ejected.
Use one of the marked keys to select the desired paper path, for example,
Single (2).
The printer returns to offline mode. The display alternates between the basic
menu and the menu in the following figure:
Insert a single sheet (for the procedure, see page 17, Loading single sheets).
Press the Online key to set the printer to ready status. When the printer re-
ceives data from the computer, the single sheet is automatically loaded. Press
the Load (4) key to load the single sheet before starting the printout.
Offline Tractor1
Park Load
Online
Setup
21
3
4
Single Tractor
Online
Setup
21
3
4
If you do not make a selection within 5 seconds, the menu is closed.
Load paper from
Single
Online
Setup
21
3
4
Online Single
Load
Online
Setup
21
3
4
Paper handling Quick start-up
14
Page 17
➤ Loading paper Your printer can process both fanfold paper and single sheets. For information on the
supported paper sizes, please refer to page 25 (Paper specifications).
You should only use those paper types which are approved for this printer. For more infor-
mation, please refer to the Reference Manual on the Online CD-ROM.
Fanfold paper
Make sure that the printer is set for fanfold paper printing. If
necessary, change the paper type (see page 14, Changing the
paper type).
Raise the front cover.
Remove the bottom cover A.
Open the right and left tractor flaps.
Release the coloured latch lever of the left-hand tractor and
align the tractor so that the first printing position on the paper
matches the X mark on the printer housing.
Lock the coloured lever again.
Place fanfold paper into the left-hand tractor.
A
Not available on some printer types.
ENGLISH
Quick start-up Paper handling
15
Page 18
Open the coloured latch lever of the right-hand tractor and
align it to the paper width.
Insert the fanfold paper into the right-hand tractor.
Make sure that it is inserted by the same length as on the lefthand tractor in order to avoid any paper jam.
Close the tractor flap and lock the tractor by turning the tractor lever to the rear.
Be sure to align the paper stack in parallel with the printer
and that the paper flow is unobstructed.
Re-install the bottom cover.
Lower the front cover.
Switch the printer on. The active paper source (Traktor1) appears in the display. The paper is automatically loaded when the printer is in online mode
and receives data from the computer.
Press the Load (4) key to load paper before starting the printout.
Do not tighten the paper excessively to avoid tearing the perforation holes; do not allow excessive
slack or the paper will not remain flat enough to ensure accurate feeding.
90
Online Tractor1
Load
Online
Setup
21
3
4
Paper handling Quick start-up
16
Page 19
Single sheets
Some printer models are designed for fanfold paper operation only and therefore do not feature a single sheet feeder. The front cover can therefor e not be opened on these models.
Make sure that the printer is set to single sheet mode. If
necessary, change the paper type (see page 14, Changing the
paper type).
Press the latch at the middle of the front cover. The single
sheet input tray opens downwards.
Align the left paper guide with the mark on the left of the
single sheet input tray. Adjust the right paper guide to the
width of the paper used.
ENGLISH
Quick start-up Paper handling
17
Page 20
Insert the single sheet as far into the input tray as possible.
Press the Online key to set the printer to ready status.
The sheet is automatically loaded when the printer is in online mode and receives data from the computer. Press the
Load (4) key to load paper before starting the printout.
➤ Paper transport Loaded paper (fanfold paper/single sheets) can be transported in the printer in several ways.
Make sure that the printer is in offline mode; press the Online key, if
necessary .
Key (2)
Short keypress: Paper is transported upwards step by step.
Long keypress: Continuous transport upwards.
Key (3)
Short keypress: Paper is transported downwards step by step.
Long keypress: Continuous transport downwards.
LF/FF key (4)
Short keypress: Line Feed (LF) is effected.
Long keypress: Form Feed (FF) is effected.
Offline Tractor1
Online
Setup
Park LF/FF
21
3
4
Paper handling Quick start-up
18
Page 21
➤ Moving the paper to
the tear position
You can use the Tear key to move the paper to the tear position.
Swing the soundproofing cover towards the front.
Make sure that the printer is in online mode. If necessary, press the Online
key.
Press the Tea r (4) key. The printer moves the perforation edge of the fanfold
paper to the tear edge of the top cover (see below).
The display alternates between…
and…
After having torn off the paper, press the Exit (4) key. The printer returns the
paper to the first printing position.
If a print job is active, the printer automatically returns the paper to the first
printing position.
Online Tractor1
Tear
Online
Setup
21
3
4
Tear position
Tractor1
Online
Setup
21
3
4
Online Tear
Exit
Online
Setup
21
3
4
Tear edge
ENGLISH
Quick start-up Paper handling
19
Page 22
Settings This section describes how to set the tear position, the first printing line, the print head gap as
well as the font selection and the character density.
➤ Setting the tear
position
If the tear position of the paper is not aligned with the tear edge of the top cover of the printer,
you can adjust it.
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key .
Press the Tea r (4) key. The printer performs a form feed.
Press the < (2) or > (3) key to move the perforation to the desired position.
Confirm the input by pressing the Set (1) key.
Confirm the input again by pressing the Setup key. The printer is reset to the
initial status.
The correction made – a maximum of approx. 2.5 cm (1") in each direction – will be retained
after switching the printer off.
Adjust Paperway
Menu Char
Online
Setup
21
3
4
TOF
Head Tear
Online
Setup
21
3
4
TearAdj= 00/72"*
Set < > Exit
Online
Setup
21
3
4
Settings Quick start-up
20
Page 23
➤ Setting the first
printing line (TOF)
You can use the TOF function for setting the position of the first printing line for each paper
source and each menu individually.
Before using the TOF function (if fanfold paper is used), you should first set the tear position
(see above).
Open the top cover.
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key .
Press the TOF (3) key. The printer performs a form feed.
The paper is fed to the position where the bottom edge of the
first printing line A is aligned with the tear edge of the top
cover B. The factory setting for the first printing position
(TOF) is 12/72".
Press the < (2) or > (3) key to move the first printing line to the desired position. You can set values from 0 to 220/72" for fanfold paper or for single
sheets.
Adjust Paperway
Menu Char
Online
Setup
21
3
4
TOF
Head Tear
Online
Setup
21
3
4
ComputerdruckerComputerdrucker
A
B
FormAdj= 12/72"*
Set < > Exit
Online
Setup
21
3
4
ENGLISH
Quick start-up Settings
21
Page 24
Confirm the input by pressing the Set (1) key.
Press the Setup key. The printer returns to the initial status.
The setting made will be retained after switching off the printer. For more details, please refer to the Reference Manual on the Online CD-ROM.
➤ Setting the print
head gap
The printer features automatic print head gap adjustment to the thickness of the paper used. In
setup mode, you can enter a correction value to modify the head gap that is normally determined automatically. This correction is useful for modifying the appearance of the type face
and the impact force for multi-layer paper.
The AGA (automatic gap adjustment) function must be set to On. For more detailed informa-
tion, refer to the Reference Manual on the Online CD-ROM.
Press the Setup key. The printer changes to setup mode.
Press the Adjust (2) key .
Press the Head (1) key.
Use the < (2) or > (3) key to set the range within which the automatic gap adjustment is to be corrected. You can select values in the range from -10 to +10.
Confirm the input by pressing the Set (1) key.
Press the Setup key. The printer returns to the initial status.
Negative values decrease the print head gap, positive values increase it.
The setting made will be retained after switching off the printer.
FormAdj= 17/72"
Set < > Exit
Online
Setup
21
3
4
Adjust Paperway
Menu Char
Online
Setup
21
3
4
TOF
Head Tear
Online
Setup
21
3
4
Head= 0 *
Set < > Exit
Online
Setup
21
3
4
Settings Quick start-up
22
Page 25
➤ Selecting character
density and font
You can use the CPI (= Characters Per Inch) key in setup mode to select the number of characters per inch to be printed. You can use the Font key to select resident fonts.
Press the Setup key, then the Char (4) key.
Press the CPI (3) or Font (2) key (in our example, press CPI).
Use the < (2) or > (3) key to set the desired character density. Confirm the selection by pressing the Set (1) key.
You can cancel the selection and leave the setting unchanged by pressing the
Exit (4) key.
If you pressed the Font (2) key, use the < (2) or > (3) key to select the desired
font. Confirm the selection by pressing the Set key.
You can cancel the selection and leave the setting unchanged by pressing the
Exit (4) key.
Press the Setup key. The printer returns to the initial status. It is also possible
to press the Online key. The printer then changes directly to online mode.
The selection made will not be retained after switching off the printer. For more details on
how to set the character density permanently, please refer to the Reference Manual on the Online CD-ROM.
Adjust Paperway
Menu Char
Online
Setup
21
3
4
Font CPI
Online
Setup
21
3
4
10 CPI *
Set < > Exit
Online
Setup
21
3
4
ROMAN NLQ
Set < > Exit
Online
Setup
21
3
4
Adjust Paperway
Menu Char
Online
Setup
21
3
4
ENGLISH
Quick start-up Settings
23
Page 26
T echnical data
➤ Printer
specifications
For more information on printer specifications as well as interface specifications, refer to the
Reference Manual on the Online CD-ROM.
Type T2265 T2280
Printing method Serial with 24-needle print head
Printing width 136 characters at 10 cpi
Print speed
HSQ (Matrix 12 x 10)
DPQ (Matrix 12 x 12)
CPQ (Matrix 24 x 12)
NLQ (Matrix 24 x 18)
LQ (Matrix 24 x 36)
(bidirectional mode, 10 cpi)
650 cps
600 cps
300 cps
200 cps
100 cps
(bidirectional mode, 10 cpi)
800 cps
700 cps
330 cps
245 cps
120 cps
Printing rate 540 pages/h
9 pages/min (ECMA)
600 pages/h
10 pages/min (ECMA)
Character densities 10 cpi, 12 cpi, 15 cpi, 17.1 cpi, 20 cpi
Max. resolution horizontal: 360 dpi; vertical: 360 dpi
Emulations Standard: MTPL, Epson LQ2550/LQ2170, IBM XL 24
Noise level
≤ 55 dB (A) (LQ Mode Sans Serif)
Dimensions 624 x 430 x 276 mm (B x T x H)
Weight 19 kg
Power supply
U.S.A./Canada 120 V
± 10%, 60 Hz ± 2%
Europe 230 V
± 10%, 50/60 Hz ± 2%
Power consumption at 100% throughput 60 VA
when idling: 20 VA
at 100% throughput 70 VA
when idling: 24 VA
Ambient conditions Temperature: 10° to 35°C; Air humidity: 16% to 73%
Print head No. of needles: 24; Needle diameter: 0.25 mm
No. of copies: 1 original + 6 copies
Approvals ISO 950, CE, GOST, VDE/GS+CB, cULus, FCC/B
Technical data Quick start-up
24
Page 27
➤ Paper
specifications
For more information on general paper specifications as well as paper specifications for the
optional tractor units and the automatic sheet feeder, refer to the Reference Manual on the
Online CD-ROM.
Fanfold paper Tractor1
Continuous single forms
Single set of forms
(requires individual testing)
Paper weight
No. of copies
Form thickness (max.)
60–120 g/m
2
1 + 6
0.60 mm
Single sheet feeder
Single sheets
Single set of forms
(requires individual testing)
Paper weight
No. of copies
Form thickness (max.)
80–120 g/m
2
1 + 5
0.60 mm
Sets of forms Sets of forms can only be processed if the top edge is bound.
ASF-F: Multi-part forms must be loaded with the bound top
edge down. They must be tested individually for their
suitability.
ENGLISH
Quick start-up Technical data
25
Page 28
Accessories
For additional accessories, please refer to the Reference Manual on the Online-CD-ROM.
Ribbon cassettes Order no.
Black ribbon cassette 060097
Ribbon cassette 1 x red, 3 x black 060099
Ribbon cassette with yellow, magenta, cyan, black 060098
Ribbon cassette with red, green, blue, black 060100
Accessories Quick start-up
26
Page 29
“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different f orm requires our explicit approval.
We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual.
However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.”
TRADEMARK ACKNOWLEDGEMENTS
“CENTRONICS” is a trademark of Centronics Data
Computer Corporation.
“EPSON” and “EPSON ESC/P” are registered
trademarks and “EPSON/P2” is a trademark of
SEIKO EPSON Corporation.
“IBM” is a trademark of International Business
Machines Corporation.
“MS-DOS” is a trademark of Microsoft Corporation.
“Windows”, “Windows 95”, “Windows 98“, “Windows
ME“, “Windows 2000“ and “Windows NT” are
trademarks of Microsoft Corporation.
Page 30
© September 2001 Tally Computerdrucker GmbH 063 050a
T ALLY REPRESENTATIVES
FRANCE
Tally S.A.
19 avenue de L’lle Saint Martin
F-92237 Nanterre Cedex
France
Tél.: +33 1 41 30 11 00
Fax: +33 1 41 30 11 10
http://www.Tally.fr
AUSTRIA
Tally Ges.m.b.H.
Eduard-Kittenberger-Gasse 95 B
A-1232 Wien
Austria
Tel.: +43 1 863 40 0
Fax: +43 1 863 40 240
http://www.Tally.co.at
Russian Federation and C.I.S.
Tally Representative
Park Place Moscow
Office D-206
Leninsky Prospekt 113/1
117198 Moscow
Russian Federation
Phone: +7 095 956 56 40
Fax: +7 095 956 55 41
http://www.Tally.ru
GERMANY
Tally Computerdrucker GmbH
Postfach 2969
D-89019 Ulm
Deutschland
Tel.: +49 7308 80 0
Fax: +49 7308 5903
http://www.Tally.de
ITALY
Tally S.R.L.
Via Borsini 6
I-20094 Corsico (MI)
Italia
Tel.: +39 02 48608 1
Fax: +39 02 48601 141
http://www.Tally.it
SPAIN
Tally SRL
Aleixandre 8, 2°A
28033 Madrid
España
Phone: +34 91 7219 181
Fax: +34 91 7219 936
http://www.Tally.es
SINGAPORE
T ally AMT Printers Pte. Ltd
63 Hillview Avenue
#08-22, Lam Soon Industrial Building
Singapore 669569
Phone: +65 760 8833
Fax: +65 760 1066
http://www.Tally.com.sg
U.S.A.
Tally Corp.
P.O.Box 97018
8301 South, 180th Street
Kent, WA 98032
U.S.A.
Phone:+1 425 25155 00
Fax: +1 425 25155 20
http://www.Tally.com
UNITED KINGDOM
Tally Limited
Rutherford Road
Basingstoke, Hampshire
RG24 8PD
England, U.K.
Phone: +44 870 872 2888
Fax: +44 870 872 2889
http://www.Tally.co.uk
CANADA
Tally Corp.
125 Traders Boulevard, 9
Missisauga, Ontario L4Z 2E5
Canada
Phone:+1 905 8904646
Fax: +1 905 8904567
http://www.Tally.com
Loading...