The WEBS-RETRO-MT is a kit that converts an existing ETP-MT Tower to a WEBS
Unit. This instruction manual assumes that a fully functional ETP-MT Tower has already been installed.
-capable Mass Notification
II. Contents
Before beginning installation, make sure you have all the included components. Each kit consists of two
packages. Package #1, labeled WEBS-RETRO-MT contains the painted WEBS
labeled WEBS-RETRO-KIT contains the following:
®
retrofit tower top. Package #2,
QTY Part Number Description
4 83073 WEBS® Loudspeaker
2
2
2
3 42841 10-24 x 3/4" pan head tamperproof screw
2 42839 3/4"-10 hex nut
8 42840 3/4" washer
4 42847 10-24 Hex nuts for Amplifier Bracket
III. Installation
(A) Installing the Retrofit Tower Top
1) Unplug the strobe light from the power supply and the emergency phone.
2) Take off the strobe light attached to the top of the tower by unfastening the three 10-24 x 3/4" pan
head tamperproof screws and keep them safely aside.
3) Remove the cap plate of the retrofit tower top and fasten the unit to the top of the tower with the help
of the three 10-24 x 3/4" pan head tamperproof screws provided.
4) Install the four WEBS
bottommost speakers first (see Figure 1).
5) Fasten the strobe light to the top of the cap plate of the WEBS
3/4" pan head tamperproof screws that were kept aside.
6) Pass the speaker and strobe light wiring through the center hole at the bottom of the retrofit top and
down to the bottom of the tower.
7) Close the top of the retrofit tower top with its cap plate and reconnect the strobe light wiring to the
emergency phone and to its power source.
24651 Amplifier Mounting Bracket
NA Paging Amplifier
NA 2’ Extension wire for WEBS
®
loudspeakers by locking each down with the retainer bracket starting with the
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Copyright 2009 Talk-A-Phone Co. All rights reserved.
WEBS-RETRO-MT Installation Instructions
Figure 1. Installing the WEBS® Retrofit Tower Top: (1) Cap, (2) Loudspeaker, (3) Retainer Bracket, (4) Blue Light/Strobe
(B)Installing the Amplifiers
1) Remove the rear access panel from the ETP-MT Tower.
2) Fasten the amplifiers on to the mounting plates with the hex nuts provided.
3) Connect two WEBS
other end of the cables to each of the amplifiers using the COM and 25V screw terminals (it does not
matter which wire goes to which screw terminal).
®
loudspeakers to each extension wire using the plug-in connectors. Connect the
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 2 of 4
All prices and specifications are subject to change without notice.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
Copyright 2009 Talk-A-Phone Co. All rights reserved.
WEBS-RETRO-MT Installation Instructions
4) Place a washer along with the amplifier mounting bracket on the desired anchor bolt. After adjusting
the mounting plate with the help of the obround slotted hole, fasten the plate to the anchor bolt with
another washer and hex nut (see Figure 2).
Figure 2. Installing the Paging Amplifier: (5) Paging Amplifier, (6) Amplifier Mounting Bracket, (7) 3/4"-10 hex nut, (8) 3/4"
washer, (9) Anchor bolts, (10) 3/4"-10 hex nut for tightening anchor bolts (11) Base plate of tower, (12) 3/4"-10 hex nut for
leveling anchor bolts
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 3 of 4
All prices and specifications are subject to change without notice.
NOTE: Depending on the length of threading available on the anchor bolt, you may need to use the additional
washers provided to elevate the amplifier mounting bracket so that the anchor bolt does not interfere with the
amplifier. If there is not enough threading available to install as shown above, either do not use the additional
washers, or remove the existing nut and washer and mount directly above the tower base plate.
Because this kit is being added to existing towers, installers may find conduit, electrical boxes and other objects
obstructing the area above the anchor bolts where the amplifier brackets mount. These brackets can be installed
on any 2 of the 4 anchor bolts—if you find that it is not possible to fit the brackets in the towers due to specifics of
your existing installation, please call Talk-A-Phone technical support for help.
Copyright 2009 Talk-A-Phone Co. All rights reserved.
Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.
WEBS-RETRO-MT Installation Instructions
5) Repeat steps 3 and 4 to install the second amplifier with mounting bracket to a second anchor bolt of
the ETP-MT Tower.
NOTE: Although the amplifier mounting brackets have rain shields, it is the installer's obligation to ensure that
proper drip loops are created with the help of the extension wire, in order to prevent condensation from damaging
the amplifiers.
6) Connect the power supply for the paging amplifier, blue light/strobe and any optional devices (e.g.
VOIP-CM-1.)
7) Use the PAGE VOL screwdriver-adjustable control on the paging amplifier to adjust the volume of the
page output. Rotate the control clockwise to increase the volume and counterclockwise to decrease
the volume.
8) Reattach the rear access panel.
Figure 3. Fully assembled WEBS-RETRO-MT showing Retrofit Tower Top and Paging Amplifier kit (wiring not shown)
Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Page 4 of 4