Takstar X6 User Manual

User Manual

GUANGDONG TAKSTAR ELECTRONIC CO., LTD.

Address: Longqiao Road Longxi Boluo Huizhou Guangdong China 516121

Tel: [phone] Fax: + 86 752 6383952

E-mail: [e-mail]
Website: www.takstar.com

INTELLIGENT UHF WIRELESS MICROPHONE

※Notice

1

1. Table of Contents…………………………………………………………....................................1

2. Safety Instruction/Features/How to Setup……………………………………….............2-3

3. Function and Operation………………………………………..........................................3-4

4. LCD Panel Instruction………………………………………..............................................4-6

5. Operating Instruction/Correct Usage……………………………………….........................7

6. Trouble Shooting/Maintenance……………………………………………............................8

7. Specification/Product content……………………………………………..............................9

Please read this manual detailedly before using to make
sure the correct operation of this product and exert the best
performance; please also keep this user manual properly
for future needs.

Table of Content s

9 2

Specification

System Specification

Audio Response: 80Hz~18KHz(±3dB)

Frequency Steadiness: <±0.005%

Max. Frequency Deviation: ±45KHz

S/N Ratio: >105dB

Frequency Range: 740~790MHz

Adjustable Range: 50MHz

Frequency Spacing: 250KHz

Dynamic Range: 100dB

THD: ≤0.5%

Operating Temperature: -10℃ +40℃

~

Modulation Mode: FM

Number of Channels: 200

Receiver Specification

Receiver Mode: Do uble conversio n superh eterodyn e

Interm ediate Fre quency : First: 110 MHz, Seco nd: 10.7MHz

Wirele ss Interfa ce: TNC/ 50Ω

Sensi tivity Adjustme nt Range: 1 2-32dB µ V

Max. Output Level: +10dBV

Sensi tivity: 12 dB µ V (80 dB S/ N)

Spuri ous Suppression : ≥75 dB

Transmitter Specification

Output Power: ＜10mW

Power Supply: 2pcs AA battery

Spurious Suppression: -60dB

Playtime: ＞10hrs

Product Content

Rec eiver

Han dheld m icrop hon e

Aud io conn ectin g cable

Power ada ptor

Ant enna

Rac k mount

1.5 V batter y

Use r manua l

1pc

1pc

1pc

1pc

2pcs

2pcs

4pcs

1set

Safety Instruction

Use the supplied power adaptor only and make sure that the AC power voltage is same as the

power adaptor's requirement. The unit may be damaged if other power adaptor is used.

Power supply of this system is AC 220V, fire or malfunction maybe occurred if other voltage is

used.

Do not expose the system to high temperatures, humidity, dust or liquids.

Do not apply any strong shock to it.

Do not dismantle the system. If there are any troubles such as fume or strange smell during

using, please unplug the power adaptor and get in contact with your local retailer for further

checking immediately.

Please place the batteries according to correct polarities. Take out the batteries when not using

it for a long time.

Please do not use batteries with broken or scratched surface, or short circuit may occur.

Please turn off the system and unplug the power adaptor if the system is not used for a long

time.

Features

UHF intelligent wireless audio transmission technology features stable and high interference-free

performance

Advanced frequency scan function features automatical and fast interference-free frequency

selection

Built-in digital frequency assignment system provides more than 100 sets system for engineering
installation

Infrared frequency synchronization technology, LC-display on receiver and transmitter for easy

and convenient operation

Transmitter is powered by 2pcs 1.5V batteries for easy replacement

Balanced and unbalanced output on receiver for convenient connection with various

equipments

Long operating range up to 50 meters

Transmitter housing are treated with alloy oxidation for high ruggedness and against corrosion

How to Setup

It is important to adjust the audio sensitivity properly, too high sensitivity will cause signal

distortion, too low sensitivity will reduce S/N. It is unnecessary to adjust as we have finshed

the adjustment in production.

(1)(2)(2) (3)(4)(3)

DC INPUT ANT B SENSITIVITY B BAL B OUT MIX OUT BAL A OUT

SENSITIVITY A

!

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

ANT A

(6) (7) (8) (9) (10) (7)(8)(9)

12V 600mA

(5)

3 8

If the frequency is set appropriately, up to 12 transmitters can be used in the same frequency

band; if the frequency is set inappropriately, mutual interference will be caused.

When several systems are used at one venue, please avoid overlapping the receivers.

Receiver Function and Operation

Front Panel

Rear Panel

(1) On/off power switch: press to turn on/off. The LCD lights when it is turned on.

(2) Volume control: adjust the output volume.
(3) Function buttons: adjust frequency, lock the frequency function key and automatically scan

the frequency.

(4) LCD: indicate working status, frequency/channel, squelch, signal level and audio dynamic

level.

(5) Infra-red data synchronization window: transmitting frequency specification signal to

transmitter by pressing “ACT”.

(6) Power socket: connect 12V DC power to the socket. Central electrode of socket connects

positive voltage.
(7) Antenna input socket: connect antennas for longer operating range.
(8) Sensitivity adjustment: the adjustment range is 0-10dB. The smaller value, the lower

sensitivity and shorter distance but with stronger interference rejection capacity, and vice

versa.
(9) Balanced audio output: XLR socket, two independent signal outputs.
(10) Unbalanced audio output: P socket, two mixed signal outputs.

Trou ble Sho oting

Trouble s

Pos sib le re aso ns

No indication on transmitter and

receiver

No RF signal on receiver

With RF signal, but without audio

signal

Running out of batteries or bad connection between

receiver and power supply

Frequency of transmitter and receiver is not the same or

out of operation range

The capsule of transmitter is broken or not well connected;

the squelch of receiver is too high and lead to short

operating range

Background noise of audio

signal is too loud

Audio signal distortion

Operating distance is too short,

signal is not stable

Output level of receiver is too low; there is interference

signal around or antenna on receiver is not installed

Transmitter's modulation frequency deviation is too

high; output level of receiver is too high

Squelch of receiver is too high; receiver antenna is wrongly

placed; there is a strong electro-magnetic interference

around

If there are other troubles, please contact us or your local distributor. Please do not

dismantle the product as it will void warranty.

Maintenance

Do not keep or use the system in high humidity, high electromagnetic or high temperature

environment, please take out the batteries and unplug the power adaptor if not used for a long

time.

Cleaning: please unplug the adaptor before cleaning and clean it with wet cloth. To protect the

do not use any detergent or dissolved liquid.

Power supply: make sure the power supply is within the required range, too high or too low will

affect the performance. Please place the batteries into the transmitter according to correct polarity.

Maintenance: if there are any troubles of the system, please contact your local distributor for

maintenance. Please do not dismantle the products as it will void warranty and be harmful to

yourself.

Accessory: please use the accessories supplied by manufacturer or recognized accessories to exert

the best performance.

Warranty: any dismantling without authorization may lead to cancellation of the warranty.

(1)

(2)

(3) (4)

(5)

(7)

1．

①

②
③

④

⑥

⑤

7 4

(6)

Operating Instruction/Correct Usage

A. Do not turn on the transmitter before receiver is powered on. First of all turn the receiver volume

to the minimum. Then press power button for turning on the receiver. After that, background
light of LCD indicator lights and all data as well as receiver channel, frequency and automatic
frequency matching status will display.

B. Before turning on the transmitter, please observe the RF and AF level. If there's strong

interference, please press “SCAN” button for avoiding frequency interference.

C. When the transmitter is turned on, the RF level for corresponding channel will light. Adjust the

receiver to appropriate volume and speak to the microphone, the AF level for corresponding
microphone volume will light. If there is no volume output or level meter doesn’t light, it means
the system is working abnormally and need repair.

D. Long press the power button for 3 seconds, the receiver will be power off.

1. How to use handheld wireless microphone

(1) Hold the middle part of the microphone. Please avoid holding the microphone bottom

where the antenna locates, otherwise, operating distance will be shortened. Please avoid

holding near the wire mesh cap or it will affect the sound pick up effect.
(2) Adjust the distance between microphone and mouth to adjust the tone volume.

2. How to use receiver

(1) The receiver consists of diversity receiver and non-diversity receiver. Non-diversity

receiver is more economic while diversity receiver has longer and better transmission effect.
(2) When receiver adopts omni antenna, the distance between antenna and wall (especially metal)

should be at least 0.5m.
(3) The receiving range is related to many factors with great changes. When there is no large metal

parts obstruct its transmission direction, it will have a better transmission effect.
(4) If the receive condition is unsatisfactory, please use extension cable with external high gain

antenna or even antenna amplifier to achieve obvious distance increasing effect.

(5) When receiver panel is put towards the operating direction or the receiver is built in the metal

case, please connect the antenna to front panel to achieve better receiving effect.

3. How to use several systems at one venue

(1) First, please choose an interference-free RF-frequency. Within 50MHz range, usually 12pcs

of transmitters can be used at the same time. If more sets need to be used at the same time,

please choose other frequency range.
(2) When several transmitters are used at the same time, the distance between transmitters in

different frequencies should be at least 20cm to avoid interference.
(3) When several receivers are used at the same time, it is suggested to install high gain antenna,

antenna amplifier and receiver multi-coupler.

Handheld Microphone Function and Operation

(1) Wire mesh cap and capsule: wire-mesh cap protects the capsule, eliminates pop noise and

prevent rolling.

(2) LCD indicator: indicate channel, battery power and RF power.

(3) Power switch: press to turn on/off the transmitter.

(4) Microphone housing: assemble wire mesh cap and capsule on the top, with battery and PCBA

inside, and antenna at the rear.

(5) Infra-red frequency matching window: transmit frequency specification signal to transmitter by

pressing ACT on receiver.

(6) Tightening screw: protects capsule, prevents the cap and capsule from being disassembled by

non-professional person.

(7) Battery compartment: assemble 2pcs AA batteries.

LCD Panel Instruction

LCD all lights indication

①

②

③

④

⑥

⑤

7-level RF indication: indicates the receiver RF signal strength

7-level power level indication: indicates vocal signal dynamic

Frequency menu: indicates the current frequency

Channel menu: indicates the current channel

Lock indication: indicates the function key lock status

Channel indication: indicates the current channel

B

5mW

BAT

5 6

Button function and operation

1) Short press “SCAN” button for automatic frequency scan and “ACT” for automatic frequency

2) Long press “SCAN” for manual adjustment mode, and long press “ACT” for function key locking.

LCD panel instruction

Under the initial interface as picture 1, short press “SCAN” button for automatic channel scan.

When stop scanning, it will finish channel selection.

Under the initial interface as picture 1, long press “SCAN” button, the LED will glitter, indicates

manual frequency adjustment status; Short press or long press “ACT” or “SCAN” button for

adjusting the channel. Once loosen the button, the LED will glitter 5 seconds and stop, it means

channel adjustment is finished.

A. Channel/frequency indication and adjustment

1. Automatic channel scan mode

2. Manual frequency adjustment mode

B. Infrared frequency matching

1. Under the initial interface as picture 1, select the channel, turn on the transmitter and point the

“IR” frequency reception window to the “IR” frequency window on the receiver in line (distance

between transmitter and receiver is 10CM-30CM); short press “ACT” button, the LED indication

as picture 2 will automatically change into the actual frequency/channel display interface after

successfully transmitting the frequency. If it fails, it will show the LED indication as picture 3,

short press “ACT” to continue the frequency matching until it succeeds.

Picture 1

Picture 2

Picture 3

Picture 4

Picture 5

Picture 6

Picture 7

C. System locking

1. Under the initial interface as picture 1, long press “ACT” for function key locking. When locking

is finished, it will show the LED indication as picture 4 and all function key will be locked (except

power button and frequency matching button). Long press “ACT” button for unlocking and it will

show the interface as picture 5.

D. Power off

1. Long press “POWER” for power off and LCD indicator will show the interface as picture 6

E. LCD indicator of microphone

1. When the microphone is powered on, the LCD will light (like picture 7) and it indicates curent

channel, RF strength and battery power level. For changing the channel, please first change the

receiver channel, then point the infrared frequency window of transmitter and receiver to each

other. Then press the “ACT” button on receiver, the new channel specification signal will be

transmitted to the transmitter.

2．

3．

matching.