TAKAYA TR3 L4D01 24 Users Manual
User’s Manual
TR3-L4D01-24
Manual No.TDR-MNL-L4D01-24-EN-100
Manual No.TDR-MNL-L4D01-24-EN-090
TAKAYA RFID TR3 Series
Introduction
Thank you for purchasing a TR3-L4D01-24 RFID READER/WRITER.
Be sure to read this manual before using the product.
After reading it, store the manual in a convenient place for future reference.
Manual No.TDR-MNL-L4D01-24-EN-090
TAKAYA RFID TR3 Series
FCC
This product is conform to the FCC standards.
FCC Rules (Federal Communications Commission)
This product complies with Part 15 Subpart B and C of the FCC Rules.
FCC ID : MK4TR3-L4D01-24
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment must be professionally installed to ensure compliance with Part 15.
Antennas not allowed are strictly prohibited for use with This equipment.
This equipment is to be professionally installed by professional service trained personnel only.
SMB sockets are provided in the equipment for connecting the external antenna.
The following sentence has to be displayed on the outside of the device in which the transmitter module
is installed : “Contains FCC ID: MK4TR3-L4D01-24”
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any
other antenna or transmitter within a host device,
except in accordance with FCC multi-transmitter product procedures.
The final system integrator must ensure there is no instruction provided in the user manual or customer
documentation indicating how to install or remove the transmitter module except such device has
implemented two-ways authentication between module and the host system.
FCC §15.27 b) - Special Accessories –
If a device requiring special accessories is installed by or under the supervision of the party marketing
the device, it is the responsibility of that party to install the equipm ent using the special accessories.
For equipment requiring professional installation, it is not necessary for the responsible party to market
the special accessories with the equipment.
However, the need to use the special accessories m ust be detailed in the instruction manual, and it is
the responsibility of the installer to provide and to install the required accessories.
Regulations and Standards
Manual No.TDR-MNL-L4D01-24-EN-090
TAKAYA RFID TR3 Series
Japan Radio Law
Equipment using high frequencies: Inductive Reading/Writing Communications Equipment
Conforming standards: Inductive Reading/Writing Communications Equipment;
Standard: ARIB STD-T82
RoHS is support
Restriction of Hazardous Substances
Waste
Dispose of the Products as industrial waste.
Manual No.TDR-MNL-L4D01-24-EN-090
TAKAYA RFID TR3 Series
Failure to comply with a WARNING may result in serious injury or
death.
Failure to comply with a CAUTION may result in injury to the
operator, or damage to the items involved.
Be sure to observe the following precautions to ensure safe use of the Products.
Decomposition of this product and cable, repair, remodeling, please strictly prohibited. There is the
possibility of fire or electric shock injuries.
This product is using the RFID reader writer radio equipment. Therefore, depending on where the
applications you use may affect medical equipment. To minimize the impact of medical equipment for use,
please observe the following countermeasure. The Japan Automatic Identification Systems Association
(JAISA) guidelines are as follows: RFID antennas from implanted cardiac pacemakers or other medical
devices please 22cm apart. We recommend that you paste "RFID sticker" at equipment.
Be sure to observe the following precautions to ensure safe use of the Products.
Installation and storage environment
1. Do not use the Products in sunlight.
2. Do not use the Products in environment of spray of water, oil or chemicals.
3. Do not use the Products in environments with flammable, explosive, or corrosive gasses.
4. Do not use the Products in environment of hot humid.
5. Do not use the Products in environment of vibration or shock.
6. Do not use the Products in environment of condensation.
7. Do not use the Products in environment of around the metal is covered.
8. Do not use the Products in environment of high temperature.
9. Do not use the Products in environment that has a device that generates magnetic field and shock voltage.
10. Do not use the Products in unstable place.
11. If there is failure, discontinue use immediately, please contact us or the distributor.
Installation
1. Turn off the power before installation or removing.
2. The following effects may not work correctly.
･ Near 13.56MHz radio device
･ Near speakers , Inverter, motor and Plasma Display
3. The communication range may vary due to environment and conditions.
← RFID Sticker
Safety Precautions
The following symbols are used in this manual to indicate precautions that must be observed to ensure safe use of
this product. The precautions provided here contain important safety information. Be sure to observe these
precautions.
The following signal words are used in this manual.
Manual No.TDR-MNL-L4D01-24-EN-090
TAKAYA RFID TR3 Series
Contents
1 Product Overview ...................................................................................................... 1
1.1 Features .............................................................................................................................................. 1
2 Names of Parts and Functions ..................................................................................... 2
2.1 TR3-L4D01-24 .................................................................................................................................... 2
2.2 Antenna .............................................................................................................................................. 4
3 Setting and connection ................................................................................................ 8
3.1 Setting ................................................................................................................................................. 8
3.1.1 DeskTop ........................................................................................................................................... 8
3.1.2 Wall Mounting .................................................................................................................................. 8
3.2 Antenna installation into a host device ................................................................................................. 9
3.2.1 Installation example by Screw holes ................................................................................................... 9
3.3 Connection ......................................................................................................................................... 11
3.3.1 Attaching the Cable and Antenna ....................................................................................................... 11
3.3.2 Direct connection to the Host Device Interface. .................................................................................. 11
4 Specifications ........................................................................................................... 12
4.1 TR3-L4D01-24 .................................................................................................................................. 12
4.2 Antenna ............................................................................................................................................ 16
4.2.1 TR3-CA033 .................................................................................................................................... 16
4.2.2 TR3-CA034 .................................................................................................................................... 18
4.2.3 TR3-CA044 .................................................................................................................................... 20
4.2.4 TR3-CA045 .................................................................................................................................... 22
4.3 Coupler Cable ................................................................................................................................... 24
4.4 Antenna Cable................................................................................................................................... 25
4.4.1 WIR42696 ...................................................................................................................................... 25
4.4.2 WIR42763 ...................................................................................................................................... 25
4.4.3 09019M16 ...................................................................................................................................... 26
5 Accessories .............................................................................................................. 27
5.1 AC Adapter(TR3-PWR-19V-2) .......................................................................................................... 27
5.2 RS232C Cross-cable(CB-232C-3) ...................................................................................................... 28
6 Maintenance ............................................................................................................ 29
Revision History ............................................................................................................. 30
Manual No.TDR-MNL-L4D01-24-EN-100
1 Product Overview
TAKAYA RFID TR3 Series
Antenna
CPU
RF-ASIC
TR3-L201W4(READER/WRITER)
LED/BUZZER
Interface Module
Tags
Host Device Interface
RS-232C
Communications
UART(CMOS Level)
TR3-L4D01-24
Block Diagram
Multiplexer
Antenna
Antenna
1.1 Features
1 Product Overview
1.1 Features
This product uses the 13.56MHz frequency. This product is the electromagnetic induction type non-contact
IC can read and write RFID tag data.
This Product is designed to be embedded and integrated within OEM devices and finished products such as label
printers, cashless payment terminals or any other device that can benefit from integrated RFID capabilities.
■ Conform to international standards
ISO/IEC15693 and ISO/IEC18000-3(Mode1) is supports.
■ Software
TR3-series common communication protocol
Software Development Kit
■ Multiplexer
Select the RF output.
■ Useful
Continuous inventory mode
UID of the tag automatically sends Host Device.
RDLoop mode
UID or User Data of the tag automatically sends Host Device.
For more information please refer to the TR3-PROTOCOL manual.
■ Environmentally
EU RoHS(2002/95/EC) Support
1
Manual No.TDR-MNL-L4D01-24-EN-100
2 Names of Parts and Functions
TAKAYA RFID TR3 Series
⑨
①
②
⑥
④
⑤
⑦
⑨
③
2 Names of Parts and Functions
2.1 TR3-L4D01-24
2.1 TR3-L4D01-24
2
Manual No.TDR-MNL-L4D01-24-EN-100
2 Names of Parts and Functions
TAKAYA RFID TR3 Series
No
Name
Description
①
LED
Displays the status of this product.
②
Nameplate
RFID sticker
Production numbers.
Specify that the RFID radio waves are radiated.
③
ANT1 to ANT24
Connect the Antenna cable.
Please connect from ANT1.
④
Power Button
Power ON/OFF.
⑤
DC Jack
DC +19V input.
⑥
Connector
Connect the RS-232C cable.
⑦
FCC ID sticker
Production numbers, will be 8-digit serial number.
⑧
TÜV mark
TÜV certification mark
⑨
Screw holes
6.5mm×13mm mounting holes.
Model Name
Serial number：＊＊＊＊＊＊＊＊
2.1 TR3-L4D01-24
3
Manual No.TDR-MNL-L4D01-24-EN-100
TAKAYA RFID TR3 Series
No
Name
Description
①
Screw holes
M3 holes.
②
CN (PH)
Connect the coupler board.
③
CN (SMA)
Connect the antenna cable.
④
ferrite sheet
Paste on TR3-CA033-1 reverse side.
⑤
Nameplate
Production numbers, will be 8-digit serial number.
⑥
Inspection mark
Sub Antenna 1
TR3-CA033-1
Sub Antenna 2
TR3-CA033-2
Coupler Board
09019P04
①
①
①
①
②
②
②
③
④
⑤
⑤ ⑤ ⑥ ⑥ ⑥
Model Name
Serial number：＊＊＊＊＊＊＊＊
2.2 Antenna
2.2.1 TR3-CA033
CA033 is combined by 2 loop sub antennas and a coupler board.
2 Names of Parts and Functions
2.2 Antenna
4
Manual No.TDR-MNL-L4D01-24-EN-100
TAKAYA RFID TR3 Series
No
Name
Description
①
Screw holes
M3 holes.
②
CN (PH)
Connect the coupler board.
③
CN (SMA)
Connect the antenna cable.
④
ferrite sheet
Paste on TR3-CA034 surface side.
⑤
Nameplate
Production numbers, will be 8-digit serial number.
⑥
Inspection mark
Antenna
TR3-CA034
Coupler board
09019P05
①
①
②
③ ⑤ ④
⑥
①
①
⑤
⑥
②
Model Name
Serial number：＊＊＊＊＊＊＊＊
Antenna
TR3-CA034
Reverse side
2.2.2 TR3-CA034
TR3-CA034 is combined by loop antenna and a coupler board.
2 Names of Parts and Functions
2.2 Antenna
5
Manual No.TDR-MNL-L4D01-24-EN-100
TAKAYA RFID TR3 Series
No
Name
Description
①
Screw holes
M3 holes.
②
CN (PH)
Connect the coupler board.
③
CN (SMA)
Connect the antenna cable.
④
Nameplate
Production numbers, will be 8-digit serial number.
⑤
Inspection mark
Antenna
TR3-CA044
Coupler board
09019P16
① ① ②
③
④ ④ ⑤
①
②
⑤
Antenna
TR3-CA044
Reverse side
①
Model Name
Serial number：＊＊＊＊＊＊＊＊
2.2.3 TR3-CA044
TR3-CA044 is combined by loop antenna and a coupler board.
2 Names of Parts and Functions
2.2 Antenna
6
Loading...