TAKARA MB1200, MB1200D User Manual

Download

Page 1

USER MANUAL

Translation of the original version

BALANCE BIKE ELECTRIC FOLDABLE

TAKARA MB1200

Page 2

Page2

1. Warnings / Residual Hazards / Precautions for Use a. Warnings / Precautions for Use b. Residual Hazards c. Handling / Transport / Storage / Battery

i) Handling / Transport / Storage ii) Battery

2. Product Description a. Description / Presentation

b. Mounting accessories

i) Mounting the toe clips ii) Seat Mounting iii) Mounting the fenders iv) Mounting the buzzer

c. Technical characteristics (technical table)

3. Functions a. Folding / Unfolding the Handlebar of the Balance Bike

i) Unfolding the Handlebar of the Balance Bike

ii) Folding the Handlebar of the Balance Bike b. Protection against unauthorized use c. Charge the battery of the balance bike

i) Description of the charging of the battery

ii) Loading steps

iii) Warnings on the charge d. Functions

i) Position Parking

ii) Turning on / turning on the Balance Bike

iii) Front / Rear lighting

iv) Buzzer

v) Start / Driving

Content of the manual

Page 3

Page3

vi) Braking

4. Cleaning / Maintenance / Repairs a. Cleaning b. Brakes: maintenance / adjustments

i) Adjusting brake cable tension ii) Brake Caliper Adjustments

c. Wheels

i) Inflation ii) Wheel Alignment iii) Warnings on shocks

5. Legal indications

Importé par DIECI SAS

59 Avenue Henry Dunant, 06105 Nice Cedex 2

Page 4

Page4

1) Warnings / Residual Hazards / Precautions for Use

a) Warnings / Precautions for Use

- Do not lend your electric balance bike to anyone who is not

familiar with the device.

- When using the Balance Bike please wear appropriate

clothing and all necessary protective equipment: helmet, knee pads, elbow guards and other protections.

- Do not drive after using alcohol or drugs.

- This article is not a toy.

- You must subscribe to an insurance policy for this type of

device in the case of damage or injury caused to a third party but also in the case of injury to the user. Please inquire with your insurer.

- This device may be used by persons 14 years of age or older

and by persons with reduced physical, sensory or mental abilities, if properly supervised by an adult, and instructions for the use of the device has been given safely, and cleaning and maintenance of the balance machine can only be done by a trained adult.

- Do not allow people under 14, the elderly and pregnant women

to use the Balance Bike.

- Children should not play with the balance bike. Cleaning and

maintenance by the user should not be done by children without supervision or training.

- In case of an accident, please stay on the spot and wait for

help.

- This device is designed for personal pleasure, it is forbidden

to use it to transport people.

- Users must not exceed the weight indicated in the maximum

weight specifications, otherwise the driver could fall and get hurt, or even damage the balance (stability) function of the device.

- To ensure the safety of all, the device must be able to stop at

any time.

Page 5

Page5

- Do not be distracted while driving, answering the phone,

listening to music or doing any other activity.

- This device is allowed to run only on private roads and is

tolerated on pedestrian routes at a maximum speed of 6km / h according to local regulations, please make sure of these different regulations.

- Please use this device only in authorized locations, if this

location requires permission, please request it.

- Do not use the product on the roadway. The device is not an

approved device.

- Do not drive in dimly lit places and in the dark.

- Avoid obstacles, smooth surfaces, snow, ice and unstable

surfaces.

- Avoid irregular objects such as rolling on a branch, rubbish,

pebbles, paved streets.

-Used on rough passages or too long use could cause many

vibrations of the body that can trigger some pains, use this balance bike in a reasonable way to limit these risks.

- Avoid narrow spaces or spaces with obstacles.

- Does not allow driving on slippery roads in rainy weather

- Avoid steep slopes.

- Do not roll in sand, puddles, mud, or other wet, damp or

rugged surfaces as this may damage the electronic components of the unit.

- It is forbidden to use the electric balance bike in dangerous

places, with presence of flammable gases, vapors, liquids, dusts which could cause a fire or an explosion.

- The device must be used only with the power supplied with

the device, if the power supply is defective please return the device to the seller. The device must be powered only under the very low safety voltage corresponding to the marking of the device.

- In case of damage to the external power supply cable, it must

be replaced by a cord available from the manufacturer, you

Page 6

Page6

must under no circumstances disassemble the device or modify the components of this product.

- Do not open the device, if the device is defective or

malfunctioning, contact the seller immediately, do not try to repair by yourself.

While driving, you may be exposed to unexpected hazards or dangerous situations, which may result in serious injury, please exercise caution and care.

b) Residual Hazards

The correct use of the balance bike while respecting the good conditions of safety, does not exclude certain risks of bodily injury and material.

Residual risk

Details

Mechanicals

Cut

Training or imprisonment (caused by hair, clothing, etc. caught by moving parts)

Crushing

Risks of friction or abrasion

Loss of stability

Collision

Thermal

Explosions

Harmful to health due to hot or cold surfaces

Vibrations

Strong vibrations can be harmful to your health in case of prolonged use, or if the product is not used and

Page 7

Page7

maintained in accordance with the instructions

Materials from the

environment

Inhalation of dust and noxious fumes

Formation of dust and explosive fumes

Hydraulic fluids on the track

Damage to property and persons resulting from the projection of objects.

Ergonomic

Repetitive injuries

Bad posture

Non-use of personal protective devices

Battery failure

Unexpected restoration of power supply after a failure

c) Handling / Transport / Storage / Battery

i) Handling / Transport / Storage

When handling and / or transporting the balance bike, avoid any physical or electrical shock.

When handling, the Balance Bike must be in the "parking" position (kickstand in the open position, on a flat, sloped or uneven surface), the charger must be unplugged and the Balance Bike must be off (off).

During transport, the Balance Bike must be switched off (extinguished), properly packaged and protected to avoid any

Page 8

Page8

shocks or accidental start-up, this may cause malfunctions of the device, see a significant deterioration of the device or the battery.

Store the balance bike in a cool, ventilated, clean and dry place, in the "parking" position (kickstand in the open position, on a flat surface, on a slope or uneven), when the charger is unplugged and that the balance bike is off (off), the storage location should not be subject to large temperature differences.

The exercise machine should not be stored outdoors without protection, the balance bike should not be stored in the harsh weather, and prolonged exposure to the sun will damage the components and the battery.

The Balance Bike can be stored / handled at temperatures between 5 ° C and 45 ° C. Storage / handling temperatures should not exceed these.

The Balance Bike can be transported at temperatures between -20 ° C and 60 ° C, transport temperatures should not exceed them.

The storage without use must not exceed 2 months, it will fully charge the balance bike every 2 months to prevent the battery of the balance bike is damaged.

ii) Battery

Your balance bike contains a high capacity LithiumIon battery, for a safe use please follow the following instructions:

Page 9

Page9

- The battery cover must not be disassembled by someone who is not authorized.

- Only an authorized person can open the battery cover.

- Do not use the balance bike in the following cases: o Overheating / smoke / strong smell o Substance leaking at the battery location

- The battery used in the device contains dangerous substances.

- Do not insert anything into the battery cover.

- Only an authorized person can change the battery.

- If the battery is defective or damaged, contact a Takara electric cycle specialist who can disassemble the balance bike and change the battery.

- The balance bike equipped with a battery must not be close to a fire or a source of heat.

- The balance bike equipped with a battery must not be immersed in an acid or alkaline liquid.

- Only charge the balance machine at temperatures between 5 ° C and 45 ° C and use it only at temperatures between -20 ° C and 60 ° C.

- To maintain the longevity of the battery of the balance bike, respect the charging cycle, do not exceed the maximum charging time, regularly recharge the balance bike.

- During prolonged non-use you must recharge the balance bike completely every 2 months.

- The battery of your balance bike is recyclable and must be recycled or disposed of according to local regulations.

- Therefore the battery of your balance bike should not be disposed of as a normal household waste and

Page 10

Page10

should NEVER be incinerated as there is a risk of explosion.

- Please contact local authorities for recycling practices in your jurisdiction.

2) Product Description

a) Description/Presentation

You have just purchased a TAKARA model MB1200D electric balance bike. This new type of mobility, entirely electric and non-polluting, will enable you to perform leisure activities smoothly and without fatigue. Its 12-inch wheels equipped with disc brake allow you to enjoy your leisure comfortably and safely. This product must be used on private road. Prohibition of traffic on roads open to the public. The power of its engine will allow you to climb gentle slopes without effort, the capacity of the battery will allow you to enjoy your balance bike throughout the day. When using the Balance Bike, please wear appropriate clothing and all necessary protective equipment: helmet, knee pads, elbow guards and other protections. Do not use your electric balance machine until you have read this manual and become familiar with the device. Before using this electric balance machine, familiarize yourself with its operation, it will allow you to keep this device in the best possible conditions. This manual can help you learn how to safely operate this electrical appliance. This manual includes all instructions and notes for use; please read carefully and follow these instructions.

Page 11

Page11

List of product elements

34 5 67

Page 12

Page12

* Spare parts available for 2 years on www.takara.fr

N°

Name

Ref.

Spare parts *

Brake handle

MB1201

Handlebar

MB1202

Start button

MB1203

Folding buckle

MB1204

Front lighting

MB1205

Tire

MB1206

Front & rear brake disc

MB1207

Front mudguard

MB1208

Frame

MB1209

Footrest

MB1210

Inner tube

MB1211

Crutch

MB1212

Brake caliper

MB1213

Rear mudguard

MB1214

Rear lighting

MB1215

Saddle

MB1216

Seat height adjustment buckle

MB1217

Battery location

MB1218

Fork

MB1219

Front and rear light button

MB1220

Brake cable

MB1221

Brake cable

MB1222

Battery charge level indicator

MB1223

Throttle grip

MB1224

Handlebar folding ring

MB1225

Handle

MB1226

Buzzer

MB1227

Drums

MB1228

Front rim

MB1229

Engine with rear rim

MB1230

Charger

MB1231

Padlock

MB1232

Page 13

Page13

Seat

Fenders

Footrests

Buzzer

AC charger

Accessories

User Manual

FRONT

REAR

Padlock supplied two

keys

Page 14

Page14

WARNING ASSEMBLY FOOTBED

b) Mounting accessories

i) Mounting the footrests

Unpack the footrests. Take the first footrest and screw it clockwise onto the indicated support. Take the second footrest and screw it clockwise on the indicated support :

WARNING ASSEMBLY / DISASSEMBLY

When assembling the elements you must comply with the instructions below and the precautions to take, if you do not comply with these instructions it could cause a malfunction of the device and cause a loss of balance (stability), a fall or an accident.

Page 15

Page15

WARNING ASSEMBLY / DISASSEMBLY OF THE SEAT

ii) Seat assembly

Remove the tube frame protection, and unlock the buckle, take the saddle and unpack it, insert the saddle end into the frame tube, relock the buckle.

iii) Mounting the fenders

Inserting the

seat

Tightening the

seat down

Seat adjustment

upwards

Page 16

Page16

WARNING ASSEMBLY / DISASSEMBLY OF MUDGUARDS

Unpack the mudguards, the smaller ones attach to the front using the supplied screw and nut, the larger ones attach to the back using the screw and nut provided.

Front fender mounting :

Rear fender mounting:

iv) Mounting the buzzer

Page 17

Page17

WARNING ASSEMBLY / DISASSEMBLY SOUND ALARM

WARNING

Be sure to follow the operating instructions and settings described in this manual. It is important to prevent any mounting errors.

Unpack the horn, attach it to the left side of the handlebar using the fixing ring and the screw so that you can reach it with your thumb without removing the left hand of the handlebar (see photo).

Page 18

Page18

c) Technical characteristics

Height and

weight

SETTINGS

STANDARD DATA

Materials

Aluminum alloy / steel

Size (folded)

1080 * 430 * 490mm

Size (unfolded)

1080 * 430 * 1140mm

Wedge height

200mm

Wheel size

12 inches

Frame color

Black

Shipping weight

18.6kg

Product weight

14.3kg

Performances

Maximum load

120kg

Maximum speed

24km / h ≈

Distance

15-18km

Slope

7.2 °

Sealing

IP54

Technical

Standards

Operating temperature

Between -10 and 45 ° C Drums

6.0Ah

Max motor power

0.35kW

Basic engine power

0.25kW

Voltage of the charger

42V Loading time

4-5hours

Braking system

Front and rear disc brakes

The total value of vibrations, which are exposed the hand-arms, does not exceed 2,5 m / s².

Page 19

Page19

WARNING FOLDING / UNFOLDING THE HANDLEBAR

Make sure that the Balance Bike is in the "parking" position

(kickstand in the open position, on a flat, sloping or uneven

surface), that the charger is unplugged and that the Balance

Bike is off (off).

3) Functions

a) Folding / Unfolding the Handlebar of the Balance Bike

i) Unfolding the Handlebar of the Balance Bike

- After unpacking the product, raise the steering column

(photos n ° 1 & 2 / p22)

- Lock the folding loop (photo n ° 3 / p22), the safety pin will

automatically position itself in the closed position.

- Unlock the handlebar locking buckle (photo n ° 4 / p22)

- Position the handlebars so that the brake handles are

horizontal (photo n ° 5 / p22)

- Re-lock the handlebar locking buckle (photo n ° 6 / p22)

Page 20

Page20

Unfolding detail

Photo n°1

Photo n°2

Photo n°3

Photo n°4

Photo n°5

Photo n°6

Page 21

Page21

ii) Folding the handlebar of the balance bike

- Unlock the handlebar locking buckle (photo n ° 4 / p22).

- Position the handlebars so that the brake handles are

vertical.

- Re-lock the handlebar locking buckle (photo n ° 6 / p22).

- Unlock the safety pin up in the open position and unblock the

folding buckle AT THE SAME TIME:

- Then bend the steering column.

Page 22

Page22

b) Operating system against unauthorized use

To prevent unauthorized use of the product, please use the lock provided with the product.

When you no longer use the balance bike, when it is parked or in parking mode, including in your garage, secure it by connecting the lock in this way:

- Position the lock so that it surrounds the wheel and the fork to lock the wheel system.

- Insert the cable end into its hole at the other end of the cable.

- Insert the key into the lock and turn the key to lock or unblock the lock.

Blocked wheel

Page 23

Page23

LOADING WARNING

Make sure that the balance bike is in the "parking" position (kickstand in the open position, on a flat surface, neither on a slope nor uneven), that the Balance Bike is off (off). DO NOT ABSOLUTELY HAVE THE DRAISIAN TURNED ON DURING THE LOAD CYCLE, that the Balance Bike is in a dry place, away from the sun, rain, that the Balance Bike and the charging port are completely dry, do not use a standard 220Volt outlet.

c) Charge the battery of the balance bike

i) Description of the charging of the battery

- Connect the power cable to the charger.

- Open the charging port cover and the charging port

sealing plug (photo # 1 / p25).

- Plug the charger cable with the male charging port into

the charging socket on the balance machine (photo # 2 / p25).

- Connect the power cable to the standard 220Volt

socket (photo n ° 3 / p25).

220V

Page 24

Page24

- To disconnect after charging, please disconnect the power cable from the 220V socket.

- Then disconnect the charging cable (photo n° 3 / p25).

- Close the waterproof plug of the charging port and close the charging port cover (photo n ° 1 / p25).

ii) Loading steps

- After properly connecting the charging port and the

power cable, the charger indicator light will glow red.

Photo n°1

Photo n°2

Photo n°3

RED

Page 25

Page25

- After 4-5 hours the charging cycle will be complete, the

indicator light of the charger will change from red to green.

- It will be necessary to correctly disconnect the charging

port and the power cable as seen in the previous step (See point i - description of the charging - photo n ° 3 / p25).

iii) Warnings on the charge

Please keep the loading environment clean and dry.

Please use a 220Volt standard outlet. Make sure that the charging port of the balance bike and

charger are dry. If the charging port is wet, do not charge the balance bike. The MAXIMUM charging time should not exceed 6 hours, if it is

exceeded it will affect the longevity of the battery, too long

GREEN

Page 26

Page26

WARNING PARKING POSITION

The balance bike must be put in "parking" position on a flat surface, neither sloping nor uneven.

charging time could cause overheating and thus increase the risk of fire or explosion.

ALWAYS unplug the charger from the balance machine and the power outlet after a full charging cycle to avoid overheating and not to alter the life of the battery. Do not leave the charger and the balance connected. continuous (whole day), this could increase the risk of fire or explosion.

ABSOLUTELY NOT leave the balance bike charge unattended at night.

Do not leave the Balance Bike unattended. People under 14 years of age or with reduced physical, sensory or mental abilities can not handle the charging of the balance bike.

When using the balance bike too much, it is possible that the battery will go down to a level of load below the minimum threshold required. In this case it is possible to reboot the load by connecting and disconnecting the charger several times to the charge port of the balance bike (Coaxial plug). Check during this operation that the charger is connected to a power outlet (220 Volts)

NEVER TURN THE DRAISIAN ON DURING THE LOAD CYCLE.

Functions

iv) Position Parking

To put the balance bike in the parking position, you must make sure that the balance bike is off (no lights / charge indicators

Page 27

Page27

WARNING START UP

Make sure that the Balance Bike is in the "parking" position (kickstand in the open position, on a flat, sloping or uneven surface), folding ring, safety pin, clamping ring tightly closed, that the loader unplugged and the balance bike is off (off). The balance bike must be put in "parking" position on a flat surface, neither sloping nor uneven.

on), then you have to open the stand so that you can keep the balance bike upright without human assistance.

v) Turning on / turning on the Balance Bike

To turn on your balance bike you must press the button to the left of the handlebar with the pictogram, the button will remain in the depressed position..

Page 28

Page28

On power-up an electronic anti-start safety device will prevent you from operating the accelerator during the lighting of the balance bike as follows:

- Press the power button

*** Start-up security ***

- Flash of the green charge indicators

- One after another ignition of the green charge indicators

according to the charge of the balance bike (1/2/3/4 lights come on consecutively)

*** End of boot safety ***

- Possibility of operating the accelerator

- It is impossible to operate the accelerator before the ignition

process is completed, that is to say before the end of the antistart electronic security.

Page 29

Page29

This electronic immobilizer anti-start will allow you not to operate the accelerator and the power of the balance bike, thereby limiting the risk of falling at the start.

vi) Front / Rear lighting

Front / rear lighting: press the push button on the right side of the handlebar for 3 seconds to switch on the headlights. A second press of 3 seconds on this push button will turn off the front and rear lights.

NB: If you turn off the balance, the headlamps will turn off automatically.

Brake / rear lighting: the action on one or the other of the brake handles will make the rear light blink.

vii) Buzzer

Page 30

Page30

WARNING STARTING

WARNING DRIVING

Do not turn the handlebar abruptly as this may increase the risk of falls, as well as damage the steering column of the balance bike. Control your speed! You must adapt your speed to your area of use, NEVER push the balance bike to its maximum speed as

A bell positioned on the handlebars will allow you to signal your presence to others.

viii) Start / Driving

1 Sit on the saddle of the balance bike. 2 Put your Balance Bike in the On position. 3 Raise the stand and place both feet on the ground to maintain stability (stability) before starting. 4 Gently turn the throttle grip on the right side of the handlebar. 5 The balance bike will move, you can accelerate to gain speed. 6 After a few meters, you can put your feet on the footrests, the balance bike will be in equilibrium position (stability). 7 To turn right, turn the handlebar to the right, to turn left, turn the handlebar to the left. 8 If you release the throttle the balance bike will slow down until it stops, it will be necessary to put the feet on the ground to not lose the balance (stability). 9 The use of the right and left brakes is discussed in the following paragraph. 10 Put the balance bike back in the "parking" position when it is completely switched off

Page 31

Page31

ix) Braking

The balance bike is equipped with two disc brakes for a safe use experience.

The brake handle on the right handlebar activates the front brake.

The brake handle on the left of the handlebar activates the rear brake.

Front disc brake

Rear disc brake

Page 32

Page32

WARNING BRAKING

The use of the brake must be done smoothly, do not press too hard on the brakes to avoid slippage or tilting. It is not possible to operate the accelerator during the action of one of the brake handles because the action of the brake handles cut the engine, this being to prevent the risk of slipping and limit the chances of losing control of the balance bike.

CLEANING WARNING

Make sure that the Balance Bike is in the "parking" position (kickstand in the open position, on a flat, sloped or uneven surface), that the charger is unplugged and that the Balance Bike is off (off). Make sure that the charging port is protected by the rubber plug, to avoid damaging the device by introducing water.

During the action of one of the brake handles this cuts the

electric motor preventing the effect of slippage and allowing a faster and softer braking.

4) Cleaning / Maintenance / Repairs a) Cleaning

- Clean with a damp cloth to remove dust and dirt.

- Do not use industrial cleaners or solvents as this may damage the surfaces.

- Do not use alcohol or ammonia cleaners as this may damage the components.

Page 33

Page33

WARNING BRAKES

Make sure that the Balance Bike is in the "parking" position (kickstand in the open position, on a flat, sloping or uneven surface), that the charger is unplugged and that the Balance Bike is OFF (off). Please check the brakes before use. Pay attention to the brake voltage and use the supplied key if they are too loose or too tight.

b) Brakes: maintenance / adjustments

i) Adjustment of brake cable tension

The manipulations are identical for the front and rear brakes.

To tighten or loosen the brakes use the supplied wrench, unscrew the nuts at the cables placed on the brake shoes and pull the cable slightly to shorten or lengthen it according to the desired action:

Page 34

Page34

- Shortening the cable will release the brake voltage:

- Lengthening the cable will tighten the brake voltage :

- Retighten the screw with the key while holding the cable to the desired length :

Page 35

Page35

- Test the cable tension with the corresponding brake handle :

Right brake handle => front brake.

Left brake handle => rear brake.

- The tension in the handle should be neither too strong nor too loose.

WARNING THE BALANCE BIKE MUST ALWAYS REMAIN OFF DURING SETTINGS.

Page 36

Page36

BRAKING TEST

Raise the balance wheel, manually turn the wheel corresponding to the brake you have just adjusted.

While the wheel is spinning, operate the brake handle, stopping the rotation of the wheel must be instantaneous.

If the stop is not immediate, braking will not be optimal. Repeat the procedure.

BRAKE HANDLE MUST NOT TOUCH HANDLEBAR HANDLE.

ii) Brake Caliper Adjustments

When dismounting the front or rear wheels, it is essential to adjust the brake calipers.

To adjust the disc and brake calipers, use the supplied key. The disc must be perfectly aligned between the pads as below. You can check by looking over the stirrup.

Page 37

Page37

To make the settings:

- Loosen the screws (pictures n ° 2 and 3 p40). The stirrup must be able to move transversely when it is handled.

- Align the disc and the pads so that the space is parallel and identical from left to right of the disc.

You will need to move the brake caliper from left to right and up and down to find the correct position.

Photo n°2

Photo n°3

Photo n°1

Page 38

Page38

- If the adjustment is correct, tighten the screws slowly so as not to lose the position.

- Tighten the brake handle corresponding to the brake caliper you have just adjusted and then release.

- Visually check the alignment (photo n ° 1 / p40)

- If it is not optimal, repeat the procedure.

- If the alignment is visible, ask an assistant to turn the wheel. The wheel must turn without forcing or making noise during its rotations.

Page 39

Page39

WARNING WHEELS

PRESSURE : 2.2 Bars

- If the wheel seems to force or make friction noises, repeat the procedure.

ATTENTION LA DRAISIENNE DOIT TOUJOURS RESTER

HORS TENSION PENDANT LES REGLAGES DES FREINS.

c) Wheels

i) Inflation

The manipulations are identical for the inflation of the front and rear wheels.

WARNING THE DRAISIAN MUST ALWAYS REMAIN OFF DURING SETTINGS. DES FREINS.

Page 40

Page40

- Make sure that the beak of the inner tube is perpendicular to the rim (see picture below) to avoid pinching the tube and / or premature wear of the tube.

- Use a suitable inflator, type car inflator to check the tire pressure and if necessary reinflate the tube.

- Remove the nozzle cap from the inner tube, insert

the nozzle of the inflator, inflate the tire, screw the cap of the nozzle of the tube.

- The pressure must be 2.2 Bars in each wheel.

Page 41

Page41

ii) Wheel Alignment

The two wheels must be perfectly aligned with the frame, if this is not the case, do not use the balance bike, the wheels could be veiled, the frame, the fork or the twisted axis of direction making the use of the dangerous balance bike. In one of these cases, use a person authorized to perform the necessary repairs. If the wheels are aligned, you can use your balance bike normally.

Page 42

Page42

iii) Warnings on shocks

If you suffer a shock on one of the wheels of your balance bike, it could result in:

▪ Abolish the tube ▪ Absorb the rim of the wheel ▪ To sail the wheel ▪ Twist the fork ▪ Abolish the steering axis ▪ Twist the frame

So a big shock on one of the wheels can have consequences on the possibility of use of the balance bike, it will be necessary to appeal to a person authorized to make a diagnosis on the overall condition of your balance bike. If your bike suffers a big shock on its wheels no longer use the balance bike and have a diagnosis by a professional.

5) Legal indications

Imported by: DIECI SAS 59 Avenue Henry Dunant 06105 Nice Cedex 2

Copyright 2018 DIECI SAS, this manual and all the information indicated in it are the property of DIECI SAS, any partial or complete copy of this document exposes the offender to prosecution. The photos in this manual are not contractual.

Page 43

Page43

We, DIECI SAS - 59 Avenue Henry Dunant - 06105 Nice Cedex 2 - FRANCE, declare that this declaration of conformity is established under our sole responsibility :

Brand : TAKARA Reference : MB1200D Type : DRAISIENNE ELECTRIQUE PLIABLE

To which this declaration refers, it complies with the essential requirements and other relevant provisions of EC Directive 2014/30 / EU and the MD 2006/42 / EC machine directive in application of the following relevant harmonized standards:

-EN 55014-1:2017 et EN 55014-2:2015

-EN 61000-3-2:2014 et EN 61000-3-3:2013

-EN ISO 12100 :2010

-EN 60204-1 :2006+A1 :2009+AC : 2010 As well as the essential requirements of the ROHS directive

2011/65 / EU of the directive LVD 2014/35 / EU and the REACH regulation.

DIECI SAS can not be held responsible for changes made by the user and their consequences, which could in particular affect the conformity of the product with the CE marking, any unauthorized modification of the product cancels this declaration of conformity.

Nice, the 10th of October 2018 Roger-David Lellouche PDG